cover_NX-PN10[C].
safety_NX-PN10[C].fm Page 1 Monday, April 27, 2009 4:22 PM Warnings, Cautions and Others Mises en garde, précautions et indications diverses CAUTION The button in any position does not disconnect the mains line. Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. • When the system is on standby, the STANDBY lamp lights red.
safety_NX-PN10[C].fm Page 2 Monday, April 27, 2009 4:22 PM For Canada/pour le Canada THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
safety_NX-PN10[C].fm Page 3 Monday, April 27, 2009 4:22 PM Caution: Proper Ventilation To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: 1. Front: No obstructions and open spacing. 2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below. 3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
NX-PN10[C].BOOK Page 1 Friday, May 21, 2010 11:24 AM Contents Introduction................................................. 2 Precautions ................................................................ 2 Getting Started............................................ 3 Connections................................................................ 4 Canceling the Display Demonstration (Demo) .......... 6 Turning on the Power Automatically (Motion Sensor) ..................................................
NX-PN10[C].BOOK Page 2 Friday, May 21, 2010 11:24 AM Introduction Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. Precautions Installation • Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C. • Install the unit in a location with adequate ventilation to prevent internal heat buildup inside the unit.
NX-PN10[C].BOOK Page 3 Friday, May 21, 2010 11:24 AM Getting Started • In this manual, operations using the remote control are mainly explained; however, you can use the buttons and controls on the unit if they have the same (or similar) name and marks. • In this manual, “iPod” means both iPod and iPhone devices. When iPhone device is especially mentioned, “iPhone” is used in this case.
NX-PN10[C].BOOK Page 4 Friday, May 21, 2010 11:24 AM Connections Do not connect the AC power cord until all other connections have been made. Connecting the Antenna FM antenna (supplied): Extend it so that you can obtain the best reception. Rear side For better FM reception Disconnect the supplied FM antenna and connect to an outdoor FM antenna using a 75 Ω wire with coaxial type connector.
NX-PN10[C].BOOK Page 5 Friday, May 21, 2010 11:24 AM Connecting the Video Cord to View a Video/Picture from iPod When viewing a video/picture from iPod on your TV, use a composite video cord (not supplied) to connect the VIDEO OUT jack on the unit and the composite video input on your TV. • After you have connected the unit, change the video input mode on your TV. For details, also refer to the instruction manual for your TV.
NX-PN10[C].BOOK Page 6 Friday, May 21, 2010 11:24 AM Canceling the Display Demonstration (Demo) When you connect the AC power cord for the first time, the display demonstration starts automatically. • When you operate the unit, the display demonstration stops temporarily. If no operation is done for about 2 minutes, the unit starts the display demonstration again. Button Operation On the unit Hold down until “DEMO OFF” appears on the display.
NX-PN10[C].BOOK Page 7 Friday, May 21, 2010 11:24 AM Basic Operations Main Unit Illumination panel (P.10) Dock A (P.13) Dock B (P.13) Motion sensor (P.6) Display (P.8) Remote control sensor STANDBY lamp Operating on the Main Unit Buttons Operations Turns on or off (standby) the power. Activates or deactivates Motion Sensor (P.6).
NX-PN10[C].BOOK Page 8 Friday, May 21, 2010 11:24 AM Buttons Operations Activates or deactivates the display demonstration (P.6). Adds the powerfulness to the sound (P.11). Stops the timer sound and restarts it 5 minutes later (P.22). • iPod (P.14): Press: Reverse skip/forward skip. Hold down: Reverse search/forward search. • FM (P.17): Tunes in to a station. • Changes the source to iPod /iPod (P.14). • Starts playback and pauses for iPod (P.14). Changes the source to FM (P.17) or AUDIO IN (P.19).
NX-PN10[C].BOOK Page 9 Friday, May 21, 2010 11:24 AM Symbols Description ST Lights up when FM stereo broadcast is received. MONO Lights up when FM monaural reception mode is activated. TUNED Lights up when an FM station of sufficient signal strength is tuned in. FM Lights up when FM is selected as the source. 1/2/3 SLEEP • Lights up when Timer is set (P.21). • 1/2/3 icon flashes while Timer is working. Lights up when Sleep Timer is activated (P.11). Remote Control P.10 P.11 P.20, P.22 P.14, P.
NX-PN10[C].BOOK Page 10 Friday, May 21, 2010 11:24 AM Buttons Main operations Changes the display information. • For iPod A/iPod B/AUDIO IN: • When the unit is turned off: Source name Clock Day of the week Clock Day of the week • For FM: Frequency Clock Day of the week Changes the source to FM (P.17) or AUDIO IN (P.19). • Changes the source to iPod /iPod (P.14). • Starts playback and pauses for iPod (P.14). Adjusts the volume level (VOL MIN/VOL 0 to VOL MAX/VOL 30). Drops the volume in a moment.
NX-PN10[C].BOOK Page 11 Friday, May 21, 2010 11:24 AM To turn off the unit after a certain period of time—Sleep Timer Press repeatedly to specify the time (in minutes) as follows: 10 30 20 OFF (Canceled) 180 60 150 90 120 • To check the time remaining before the shut-off time, press SLEEP once. If you press the button repeatedly, you can change the shut-off time. To emphasize the sound—Sound Turbo You can add the powerfulness to the sound. Press to activate Sound Turbo.
NX-PN10[C].BOOK Page 12 Friday, May 21, 2010 11:24 AM Playing Back from iPod Devices You can connect 2 iPod devices to the unit and enjoy sound and video from them.
NX-PN10[C].BOOK Page 13 Friday, May 21, 2010 11:24 AM Connecting iPod Connect iPod to dock A or B on the unit. You can have 2 iPod devices connected at the same time. • Make sure the unit is on standby when you connect iPod. Dock adapter (supplied with iPod or sold separately) Dock A Dock B To detach the dock adapter from the dock: Pull up the dock adapter with your fingernail or a sharp-pointed tool using the slot. • Be careful not to injure your fingertips or damage the terminal of the dock.
NX-PN10[C].BOOK Page 14 Friday, May 21, 2010 11:24 AM Operations For details, also refer to the instruction manual for iPod. NOTES: • Before viewing a video/picture from iPod on your TV, make the appropriate video setting on iPod. For details of the setting, see the instruction manual for iPod.
NX-PN10[C].BOOK Page 15 Friday, May 21, 2010 11:24 AM Buttons On the unit Operations On the remote Confirms an item on the menu/screen. — * Control of iPod Center button* — Press: Applies Shuffle Play to iPod or iPod selected as the source. Select the desired shuffle mode. “SHUFFLE” appears for a while. • The shuffle icon lights up on the display of iPod. • To cancel, press again until the shuffle icon disappears. Hold down: Applies Shuffle Play to both iPod and iPod if connected.
NX-PN10[C].BOOK Page 16 Friday, May 21, 2010 11:24 AM NOTES: • JVC is not responsible for any loss of or damage to iPod that might result from the use of this product. • Do not touch or hit the terminals of the dock and of iPod. It might cause damage to these terminals. • When you connect iPod to the dock, make sure the terminal on the dock is fully inserted into iPod. • Always set the volume to the minimum level when connecting or disconnecting iPod. • Do not carry the unit with iPod connected.
NX-PN10[C].BOOK Page 17 Friday, May 21, 2010 11:24 AM Listening to FM Broadcasts Basic Operations Buttons Operations On the unit On the remote Selects FM as the source. FM AUDIO IN When an FM program is broadcasted in stereo, ST (stereo) lights up on the display (only when the reception is good). Press: Changes the frequency. Hold down and release: The unit starts searching for stations and stops when a station of sufficient signal strength is found. • To stop searching, press again.
NX-PN10[C].BOOK Page 18 Friday, May 21, 2010 11:24 AM Presetting Stations You can preset 30 FM stations. 1 Select FM as the source. 2 Tune in to the station you want to preset. • You can also store the monaural reception mode for FM preset stations if selected. 3 Activate the preset number entry mode. “SET” flashes on the display for a few seconds. • Complete the following operations while the indication is flashing. Select a preset number for the station you want to store. 4 5 Store the station.
NX-PN10[C].BOOK Page 19 Friday, May 21, 2010 11:24 AM Playing Back from Other Equipment Connecting Other Equipment By using a stereo mini plug cord (not supplied), you can connect other equipment with analog audio output jacks, such as a portable audio player, etc. To headphones or audio out Stereo mini plug cord (not supplied) Portable audio player Rear side • Refer to the instruction manual supplied with the equipment.
NX-PN10[C].BOOK Page 20 Friday, May 21, 2010 11:24 AM Setting the Clock and Timer Setting the Clock Set the built-in clock before using Timer. • You can set the clock when the unit is turned on or on standby. 1 Activate the clock setting mode. “ADJCLOCK” appears then the hour digit of the time indication flashes on the display. • If you have already set the clock before, press the button twice to activate the clock setting mode. TIMER 1/TIMER 2/TIMER 3* Canceled 2 Clock setting * See “Using Timer”.
NX-PN10[C].BOOK Page 21 Friday, May 21, 2010 11:24 AM Select Timer you want to set. TIMER 1 2 TIMER 2 TIMER 3 Select Timer type. WEEKLY 3 ONCE WEEKLY: See step 4 below. ONCE: Timer works once on a selected day of the week. Select the desired day of the week. • When “WEEKLY” is selected in step 3: SUN DAY THU DAY MON-SAT 4 MON DAY FRI DAY EVERYDAY WED DAY TUE DAY SAT DAY MON-FRI Back to the beginning SUN DAY to SAT DAY: Timer works every week on the selected day.
NX-PN10[C].BOOK Page 22 Friday, May 21, 2010 11:24 AM To Cancel Timer Select Timer you want to cancel. TIMER 1 1 2 TIMER 2 TIMER 3 “CANCEL” flashes on the display. The icon and the timer number indicator (1/2/3) disappear. NOTE: The settings you have made are memorized though you cancel Timer. To Turn off the Timer Sound briefly—Snooze Using Snooze, you can have the timer sound stop and restart it 5 minutes later. 1 Set Timer following the steps 1 to 6 on pages 20 and 21.
NX-PN10[C].BOOK Page 23 Friday, May 21, 2010 11:24 AM Troubleshooting If you have a problem with your unit, check this list for a possible solution before calling for service. General iPod Operations Power does not come on. iPod doesn’t play though iPod /iPod The power plug is not inserted securely. Plug lights up on the display. it in securely (P.5). The battery is empty. Leave it connected for more than 10 minutes. Power turns on even though you turned off. Motion Sensor is activated (P.6).
NX-PN10[C].BOOK Page 24 Friday, May 21, 2010 11:24 AM Specifications Accessories Main Unit See page 3. Output Power 10 W (5W+5W) at 8 Ω (10%THD) Dimensions (W/H/D): 326 mm × 135 mm × 130 mm Mass: Approx. 1.6 kg Terminals Speaker Specifications Amplifier AUDIO IN Input Sensitivity/Impedance (1 kHz): LEVEL 1: 500 mV/47 kΩ LEVEL 2: 315 mV/47 kΩ LEVEL 3: 125 mV/47 kΩ Dock A and B for iPod/iPhone Compatible iPod/iPhone models: See page 12.
NX-PN10_FR_5.book Page 1 Monday, April 27, 2009 3:12 PM Table des matières Introduction................................................. 2 Précautions ................................................................ 2 Pour commencer ......................................... 3 Connexions................................................................. 4 Annulation de la démonstration des affichages (Demo) ...............................................................
NX-PN10[J].fm Page 2 Tuesday, April 28, 2009 10:20 AM Introduction Merci pour avoir acheté un produit JVC. Veuillez lire attentivement toutes les instructions avant d’utiliser l’appareil afin de bien comprendre son fonctionnement et d’obtenir les meilleures performances possibles. Précautions Installation • Installez la chaîne dans un endroit plat, sec, et ni trop chaud, ni trop froid—entre 5°C et 35°C.
NX-PN10[J].fm Page 3 Tuesday, April 28, 2009 10:20 AM Pour commencer • Dans ce manuel, nous expliquons principalement les opérations à l’aide de la télécommande; cependant, vous pouvez utiliser les touches et les commandes de l’appareil si elles portent le même nom (ou un nom similaire) et la même marque. • Dans ce manuel, “iPod” est utilisé à la fois pour iPod et pour iPhone. Quand un appareil iPhone est spécialement mentionné, “iPhone” est utilisé à la place.
NX-PN10_FR_5.book Page 4 Monday, April 27, 2009 3:12 PM Connexions Ne branchez pas le cordon d’alimentation secteur avant d’avoir effectué toutes les autres connexions. Connexion de l’antenne Antenne FM (fournie): Étendez-la de façon à obtenir la meilleure réception possible. Arrière Pour une meilleure réception FM Déconnectez l’antenne FM fournie et connectez l’appareil à une antenne FM extérieure en utilisant un connecteur de type coaxial 75 Ω.
NX-PN10[J].fm Page 5 Tuesday, April 28, 2009 1:45 PM Connexion de cordon vidéo pour voir une séquence vidéo/image de l’iPod Pour afficher une séquence vidéo ou d’une image à partir de votre iPod sur votre téléviseur, utilisez un cordon vidéo composite (non fourni) et connectez-le à la prise VIDEO OUT sur l’appareil et à l’entrée vidéo composite du téléviseur. • Après avoir connecté l’appareil, changez le mode d’entrée vidéo de votre téléviseur.
NX-PN10_FR_5.book Page 6 Monday, April 27, 2009 3:12 PM Annulation de la démonstration des affichages (Demo) Quand vous connectez le cordon d’alimentation pour la première fois, la démonstration des affichages démarre automatiquement. • Quand vous utilisez l’appareil, la démonstration des affichages s’arrête temporairement. Si aucune opération n’est réalisée pendant environ 2 minutes, l’appareil démarre de nouveau la démonstration des affichages.
NX-PN10_FR_5.book Page 7 Monday, April 27, 2009 3:12 PM Opérations de base Appareil Panneau d’illumination (P.10) Dock A (P.13) Dock B (P.13) Capteur de mouvement (P.6) Affichage (P.8) Capteur de télécommande Témoin STANDBY Fonctionnement sur l’appareil Touches Opérations Met en marche/arrête (met en veille) l’appareil. Met en ou hors service le capteur de mouvement (P.6).
NX-PN10_FR_5.book Page 8 Monday, April 27, 2009 Touches 3:12 PM Opérations Met en ou hors service la démonstration des affichages (P.6). Ajoute de la puissance au son (P.11). Arrête le son de la minuterie et le redémarre 5 minutes plus tard (P.22). • iPod (P.14): Appuyez sur: Saut vers l’arrière/saut vers l’avant. Maintenez pressée la touche: Recherche vers l’arrière/vers l’avant. • FM (P.17): Accorde une station. • Change la source sur iPod /iPod (P.14).
NX-PN10_FR_5.book Page 9 Monday, April 27, 2009 Symboles 3:12 PM Description ST S’allume quand une émission FM stéréo est reçue. MONO S’allume quand le mode de réception FM monophonique est en service. TUNED S’allume lors de la réception d’une station FM dont le signal est suffisamment fort. FM S’allume quand FM est choisi comme source. 1/2/3 SLEEP • S’allume lorsque la minuterie est réglée (P.21). • L’icône 1/2/3 clignote pendant le fonctionnement de la minuterie.
NX-PN10_FR_5.book Page 10 Monday, April 27, 2009 Touches 3:12 PM Opérations principales Change les informations de l’affichage. • Pour iPod A/iPod B/AUDIO IN: Nom de la source Horloge Jour de la semaine • Quand l’appareil est mis hors tension: Horloge Jour de la semaine • Pour FM: Fréquence Horloge Jour de la semaine Change la source sur FM (P.17) ou AUDIO IN (P.19). • Change la source sur iPod /iPod (P.14). • Démarre et interrompt la lecture pour iPod (P.14).
NX-PN10[J].fm Page 11 Tuesday, April 28, 2009 10:20 AM Pour mettre l’appareil hors tension après une certaine période de temps—Minuterie d’arrêt Appuyez répétitivement sur la touche pour spécifier la durée (en minutes) de la façon suivante: 10 30 20 OFF (Annulée) 180 60 150 90 120 • Pour vérifier le temps qui reste avant que l’appareil s’éteigne automatiquement, appuyez une fois sur SLEEP. Si vous appuyez répétitivement sur la touche, vous pouvez changer l’heure de mise hors tension.
NX-PN10_FR_R1.book Page 12 Thursday, May 20, 2010 2:05 PM Lecture à partir d’un iPod Vous pouvez connecter 2 iPod à l’appareil et écouter leur son et voir leurs images.
NX-PN10_FR_5.book Page 13 Monday, April 27, 2009 3:12 PM Connexion de iPod Connectez l’iPod au dock A ou B de l’appareil. Vous pouvez connecter 2 iPod en même temps à l’appareil. • Assurez-vous que l’appareil est en mode d’attente quand vous connectez un iPod. Adaptateur de dock (fourni avec iPod ou vendu séparément) Dock A Dock B Pour détacher l’adaptateur de dock du dock: Tirez sur l’adaptateur de dock avec le bout de votre doigt ou un outil pointu que vous insérez dans la fente.
NX-PN10_FR_5.book Page 14 Monday, April 27, 2009 3:12 PM Opérations Pour plus d’information, référez-vous aussi au mode d’emploi fourni pour votre iPod. REMARQUES: • Avant de regarder une séquence vidéo/image à partir de iPod sur votre téléviseur, faites réglages vidéo appropriés sur le iPod. Pour en savoir plus sur les réglages, référez-vous au manuel d’instruction de iPod.
NX-PN10_FR_5.book Page 15 Monday, April 27, 2009 3:12 PM Touches Sur l’appareil Opérations Sur la télécommande Valide un élément sur le menu ou sur l’écran. — * Commande du iPod Bouton central* — Appuyez sur: Applique la lecture aléatoire à l,iPod ou à l’iPod choisi comme source. Choisissez le mode de lecture aléatoire souhaité. “SHUFFLE” apparaît sur l’affichage pendant un instant. • L’icône de lecture aléatoire s’allume sur l’affichage de l’iPod.
NX-PN10_FR_5.book Page 16 Monday, April 27, 2009 3:12 PM REMARQUES: • JVC ne peut être tenu responsable pour toute perte ou dommage à iPod résultant de l’utilisation de ce produit. • Ne touchez pas ni ne frappez les prises du dock et du iPod. Cela pourrait endommager ces bornes. • Quand vous connectez iPod sur le dock, assurez-vous que la prise sur le dock est complément inséré sur le iPod. • Réglez toujours le volume au minimum lorsque vous connectez ou déconnectez iPod.
NX-PN10_FR_5.book Page 17 Monday, April 27, 2009 3:12 PM Écoute d’émissions FM Opérations de base Touches Sur l’appareil Opérations Sur la télécommande Choisit FM comme source. FM AUDIO IN Quand un programme FM est diffusé en stéréo, l’indicateur ST (stéréo) s’allume sur l’affichage (uniquement quand la réception est bonne). Appuyez sur: Change la fréquence.
NX-PN10_FR_5.book Page 18 Monday, April 27, 2009 3:12 PM Préréglage des stations Vous pouvez préréglez 30 stations FM. 1 Choisissez FM comme source. 2 Réglez la station que vous souhaitez mémoriser. • Vous pouvez aussi mémoriser le mode de réception monophonique pour les stations FM préréglée s’il est choisi. 3 Mettez en service le mode d’entrée de numéro de préréglage. “SET” clignote sur l’affichage pendant quelques secondes. • Terminez les opérations suivantes pendant que l’indication clignote.
NX-PN10_FR_5.book Page 19 Monday, April 27, 2009 3:12 PM Lecture à partir d’un autre appareil Connexion d’un autre appareil En utilisant un cordon à mini-fiche stéréo (non fourni), vous pouvez connecter un autre appareil muni de prises de sortie audio analogique tel qu’un lecture audio portable, etc. Au casque d’écoute ou à la sortie audio Lecture audio portable Cordon à mini-fiche stéréo (non fourni) Arrière • Référez-vous aux manuels d’instruction fournis avec l’appareil.
NX-PN10_FR_5.book Page 20 Monday, April 27, 2009 3:12 PM Réglage de l’horloge et de la minuterie Réglage de l’horloge Réglez l’horloge intégrée avant d’utiliser la minuterie. • Vous pouvez régler l’horloge quand l’appareil est sous tension ou en mode d’attente. 1 Mettez en service le mode de réglage de l’horloge. “ADJCLOCK” apparaît puis les chiffres de l’heure clignotent sur l’affichage.
NX-PN10_FR_5.book Page 21 Monday, April 27, 2009 3:12 PM Choisissez la minuterie que vous souhaitez régler. 2 TIMER 1 TIMER 2 TIMER 3 Choisissez le type de minuterie. WEEKLY 3 ONCE WEEKLY: Voir l’étape 4 ci-dessous. ONCE: La minuterie fonctionne une fois le jour choisi de la semaine. Choisissez le jour de la semaine souhaité.
NX-PN10_FR_5.book Page 22 Monday, April 27, 2009 3:12 PM Pour annuler la minuterie Choisissez la minuterie que vous souhaitez annuler. 1 2 TIMER 1 TIMER 2 TIMER 3 “CANCEL” clignote sur l’affichage. L’icône et l’indicateur du numéro de la minuterie (1/2/3) disparaît. REMARQUE: Les réglages que vous avez réalisés sont mémorisés bien que vous ayez annulez la minuterie.
NX-PN10_FR_5.book Page 23 Monday, April 27, 2009 3:12 PM Guide de dépannage Si vous des problèmes avec votre appareil, cherchez d’abord une solution dans cette liste avant d’appeler un réparateur. Général iPod L’alimentation n’arrive pas. La fiche d’alimentation n’est pas insérée correctement. Insérez-la solidement (P.5). La lecture sur le iPod ne fonctionne pas bien que iPod /iPod soit allumé sur l’affichage. La batterie est déchargée.
NX-PN10[J].fm Page 24 Tuesday, April 28, 2009 10:19 AM Spécifications Accessoires Appareil Voir page 3. Dimensions (L/H/P): 326 mm × 135 mm × 130 mm Masse: Approx. 1,6 kg Amplificateur Puissance 10 W (5W+5W) à 8 Ω (10%DHT) Prises AUDIO IN Sensibilité/Impédance d’entrée (1 kHz): LEVEL 1: 500 mV/47 kΩ LEVEL 2: 315 mV/47 kΩ LEVEL 3: 125 mV/47 kΩ Dock A et B pour iPod/iPhone Modèles d’iPod/iPhone compatibles: Voir page 12.
cover_NX-PN10[C].