FIXED DOME CAMERA TK-C2201U TK-C2201E INSTRUCTIONS For Customer Use: Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. TK-C2201U,TK-C2201E Serial No. .
Introduction Contents Introduction Contents ............................................................................................................. 2 Features ............................................................................................................. 3 Operating Precautions ....................................................................................... 4 Name of Parts ....................................................................................................
Introduction Thank you for purchasing this product. Before use, please read this "INSTRUCTIONS" and the information materials included to ensure proper use of this product. These instructions are for TK-C2201U/TK-C2201E. Features v v v v Easy DAY/NIGHT function 3D noise reduction (3DNR) 4 areas privacy mask Built-in display mode (CRT or LCD selectable) How to read this manual Conventions and symbols Note : Indicates operating precautions.
Introduction Operating Precautions m v v v v m v m v m v v v 4 Storage and Location of Use This camera has been designed for indoor use. It cannot be used outdoors. Do not install the camera in the following places. - In a place exposed to rain or moisture. - In a place with vapor or oil, for example in a kitchen. - When the ambient temperature rises above or falls below the acceptable range (from -10 f to 50 f) - In a place at which corrosive gases are emitted.
Introduction m v m v v v v v v v v v v Disclaimer We will not be responsible for any inconveniences or disturbances caused in the event of privacy invasion as a result of camera footages of this product. Others When using this camera with [AGC] set to "MID" or "HIGH", the sensitivity increases automatically for dark images and the screen may appear grainy, but this is not a malfunction.
Introduction Name of Parts Camera (Interior) . The dome cover and inner dome are removed. Refer to "Mounting the camera directly to the ceiling or on the wall" (A page 13) step 2 to 3 on the removal methods. A B G H C I J D K E F F. ADJ MENU .
Introduction F Tilt Fastening Screw (A page 18) G Focus Adjust Gear (A page 19) H Shooting Direction Mark (A page 15) (A page 18) I Pan Center Mark (A page 18) J Rotation Center Mark (A page 18) K Function Selection Switches (A page 9) L [MENU] Button Display the menu screen. Refer to the attached manual "MENU SETTING" for more details about setting the menu. M Status Indication Lamp Lights up when the power is turned on.
Introduction Name of Parts (Continued) . Camera D E F A G .
Setup Setting the Switches Before mounting the camera, set the function setting switches on the camera. To set the switches, use a fine-tipped screwdriver. Function selection switches F. ADJ DIP SW MENU D/N AUTO 1 BLC OFF 2 MONITOR LCD 3 TYPE NOT USED 4 OFF ON CRT SEE INSTRUCTION MANUAL . DIP Switch Settings Chart 1 [D/N AUTO/OFF] Easy Day & Night Switch Set this to "AUTO" when shooting a subject with continually changing brightness (day/night).
Setup About Connection Cables . The maximum connection distance varies with the type of cable used. v Be sure to turn off the power of devices before connecting cables. To video Signal Cable . To DC 12 V or AC 24 V Power Supply Video signal cable (coaxial cable) Connect a RG-59 75 K coaxial cable (BNC) to the video signal output connecter (BNC).
Setup DC 12 V or AC 24 V power supply cable Connect the power cord to the DC 12 V or the AC 24 V power supply. The following table shows the connection distances when 2-core VVF (vinylinsulated vinyl sheath cables) are used. (Reference value) Conductor diameter Maximum connection distance: DC 12 V Maximum connection distance: AC 24 V Φ 1.0 mm (AWG 18) 50 m (160 ft) 130 m (420 ft) Φ 1.6 mm (AWG 14) 140 m (450 ft) 350 m (1100 ft) Φ 2.
Installation Mounting the Camera Mounting the camera to the ceiling Note v v v . v When mounting the camera to the ceiling, ensure to wear safety glasses to protect the eye from any falling objects. It maybe mandatory to mount an embedded cover in the ceiling (recessed bracket) in certain areas. If an embedded cover (recessed bracket) is required, ensure it is securely mounted before installing the camera.
Installation Mounting the camera directly to the ceiling or on the wall When mounting to a wall, replace areas indicated as "ceiling" in the procedures by "wall". Setup 1 Open a hole in the ceiling (Φ 30 mm, 1-1/8 inches), and draw the fall prevention wire, power supply cable and coaxial cable out from the ceiling (fall prevention wire is not included) . m 30 mm (1-1/8 inches) Power cable Fall prevention wire (not supplied) Approx. 100 mm (3-7/8 inches) .
Installation Mounting the Camera (Continued) Connection 1 Attach the fall prevention wire from the ceiling to the camera (fall prevention wire is not included) 2 Connect the coaxial cable (A page 10) m Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to cover the connectors. This will isolate and protect the metallic parts of the connectors from the ceiling structures.
Installation Mounting 1 Align (ñ) with the shooting direction, and mount the camera onto the ceiling m Mounting screw (not included) v The diameter of the attachment hole is Φ 4.5 mm (3/16 inch). v Do not use flathead screws. v When using an impact screwdriver, do not tighten the screws fully. Tighten using your hand instead. Failure to do so may damage the outer case. . . Note m Adjusting images After mounting is completed, adjust the images while checking the actual image.
Installation Mounting the Camera (Continued) Mount by allowing the cable to exit from the side When mounting the camera to the ceiling or a wall, it is possible to guide the cable from the side without opening any holes. The basic mounting method is identical to steps in "Mounting the camera directly to the ceiling or on the wall" (A page 13) . . . 1 Cut both ends of the extraction hole for the cable with a nipper and break off the excess material using tools such as long-nose pliers .
Adjustment Adjusting Image After mounting the camera, adjust the images while looking at the actual image. Discharge the static electricity from your body by touching the metallic part of the monitor terminal before handling the camera as static electricity may cause the camera to malfunction. 1 Mount the monitor Connect the monitor terminal of this camera to a test monitor to adjust the camera’s shooting direction, image and focus. . 2 Turn on the camera Monitor terminal 75 terminal .
Adjustment Adjusting Image (Continued) 3 Adjust the shooting direction of the camera Adjust the camera for pan, tilt and rotation, and face the camera towards the subject. Pan: 175 Tilt fastening screw Rotation: 100 Tilt: 80 Shooting direction mark Pan center mark Rotation center mark . Rotation knob ( 2) Memo v v v Note v v v 18 Rotate both pan 5175 7 and rotation 5100 7 from the positions aligned with the camera’s shooting direction mark, pan center mark and rotation center mark.
Adjustment 4 Adjust the image size Loosen the fastening screw for the zoom adjustment ring and move the ring to the left/right to adjust the image size. After adjustment is complete, fasten the screw with pressing it slightly toward the lens direction (toward the shooting direction). 5 Adjust the focus . . ① Hold the focus adjust gear knob, shift the catch from point A to point B as illustrated in the diagram to disengage the gear.
Adjustment Adjusting Image (Continued) 6 Fine adjust the focus . . ① Press and hold the [J] button. v Focus adjust mode will be activated and "FOCUS ADJUST MODE" is displayed on the monitor screen. v The contours are emphasized as the iris opens and the depth of field becomes shallow. v After adjustment, press [K, H, I], [SET] or [MENU] to exit focus adjust mode. The mode is also automatically deactivated after about 30 seconds.
Adjustment 7 Tighten the fastening screw of the focus adjustment ring . Hold and press the focus adjust gear between your fingers in the direction of the arrows in the diagram, and tighten the fastening screw of the focus adjustment ring. .
Adjustment Adjusting the Auto White Balance Each light source has its own color temperature. Therefore, when the main light source lighting the subject is changed, adjust the white balance again. 1 Press the [MENU] button. 2 Select [WHITE BALANCE] with the [J/K] button and "AWC" with the [H/I] button, then press the [SET] button. 3 Zoom in to fill the screen with white.
Adjustment Mounting the Dome Cover Attach the dome cover back when all settings are finished. 1 Mount the inner dome . Mount the inner dome in a way that supports the tilt direction of the lens. Insert the inner depression of the inner dome into the protruding parts beside the fastening screw. Push it in until it is locked by the catches (2 locations). Protruding part Catches ( 2) Inner depression .
Adjustment Mounting the Dome Cover (Continued) 2 Mount the dome cover, and peel off the dome cover protection sheet . ① Align the position marks of the same shape on the camera unit and dome cover. (Camera unit: double track, dome cover: double track) ② Turn and secure the dome cover in the clockwise dirction. Memo Secure the dome cover with the two screws provided if necessary. Note v When the cover is removed again after mounting the dome cover, the field angle may changed.
Others Specifications Horizontal resolution Video S/N Minimum illumination : 550TV lines (typical) : 52 dB (typical, AGC OFF) : Color mode: 0.05 lx (typical, 50 %, F1.2, AGC HIGH) Black and white mode: 0.03 lx (typical, 50 %, F1.2, AGC HIGH) Zoom ratio : 3.75 Focal length : 2.8 mm to 10.5 mm Maximum aperture : F 1.2 (f = 2.8 mm) F 3.6(f = 10.5 mm) ratio Minimum aperture : Equivalent to F 360 Angle of view : f = 2.8 mm 99.5 7 (H) 2 73.2 7 (V) f = 10.5 mm 24.4 7 (H) 2 20.
Others Specifications (Continued) External Dimensions [Unit: mm (inch)] . . m 46(1-13/16) /2) 95(3-3/4) * Specifications and appearance of this unit are subject to change for further improvements without prior notice. 26 97(3-7/8) 39(1-9/16) R4 2(1 -11 /16 ) 3-1 .5( 87 83.
Others Ceiling Mounting Hole [Unit: mm (inch)] . m Front up Screw 110 (4-3 /8) 46 (1-13/16) Camera Body 0 35 20 (13/16) 83.5 (3-5/16) 30 (1-3/16) Hole for cables Lens shooting range Screw Cable direction . 7.
TK-C2201U/TK-C2201E FIXED DOME CAMERA Q 2009 Victor Company of Japan, Limited LST0952-001A