. 4K PTZ REMOTE CAMERA KY-PZ400NWU/KY-PZ400NWE KY-PZ400NBU/KY-PZ400NBE INSTRUCTIONS (Installation/IP Address Settings) Specifications and appearance of this unit are subject to change for further improvement without prior notice. Details For details on settings and operation, refer to “INSTRUCTIONS” on the website. Please check the latest INSTRUCTIONS, tools, etc. from the URL below. North America: http://pro.jvc.com/prof/main.jsp Europe: https://eu.jvc.
FOR USA These are general Important Safety Instructions and certain items may not apply to all appliances. Important Safety Instructions 8. 9. 10. 11. 12. 13. Getting Started 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
POUR LES ÉTATS-UNIS Ces informations sont des CONSIGNES DE SÉCURITÉ IMPORTANTES et certains points peuvent ne pas s’appliquer à tous les appareils. CONSIGNES DE SÉCURITÉ IMPORTANTES Getting Started 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Lire ces instructions. Conserver ces instructions. Tenir compte de tous les avertissements. Respecter toutes les instructions. Ne pas utiliser cet appareil à proximité de l’eau. Ne nettoyer qu’avec un chiffon sec. Ne pas boucher les ouvertures de ventilation.
Safety Precautions POUR CANADA FOR USA AND CANADA ATTENTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION NE PAS OUVRIR LE BOITER. AUCUNE PIECE INTERIEURE N’EST A REGLER PAR L’UTILISATEUR. SE REFERER A UN AGENT QUALIFIE EN CAS DE PROBLEME. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Getting Started Supplier's Declaration of Conformity Model Number: KY-PZ400NWU KY-PZ400NBU JVC Trade Name: JVCKENWOOD USA Responsible Corporation party: 500 Valley Road, Address: Suite 203 Wayne, NJ 07470 973-317-5000 Telephone Number: Déclaration de conformité du fournisseur KY-PZ400NWU Numéro de KY-PZ400NBU modèle : Nom de marque : JVC JVCKENWOOD USA Personne Corporation responsable : 500 Valley Road, Adresse : Suite 203 Wayne, NJ 07470 973-317-5000 Numéro de téléphone : This device complies with Part
CAUTION: Attention: The mains plug shall remain readily operable. Remove the mains plug immediately if the camera functions abnormally. La prise secteur doit être opérationnelle. Débranchez immédiatement la fiche secteur si le caméscope ne fonctionne pas normalement. Getting Started . . WARNING: Avertissement: The battery pack, the camera with battery installed, and the remote control with battery installed should not be exposed to excessive heat such as direct sunlight, fire or the like.
Si le matériel est installé dans un coffret ou sur une étagère, s’assurer qu’il y a un espace suffisant sur tous les côtés pour permettre la ventilation (10 cm (3-15/16") ou plus sur les deux côtés, au dessus et à l’arrière). Ne pas boucher les orifices de ventilation. (Si les orifices de ventilation sont bouchés par un journal, un tissu, etc., la chaleur peut ne pas s’éliminer.) Aucune source à flamme nue, telle que des bougies allumées, ne doit être placée sur l’appareil.
Lorsque vous utilisez l'adaptateur secteur ailleurs qu’aux États-Unis The provided AC adapter features automatic voltage selection in the AC range from 110 V to 240 V. L'adaptateur secteur fourni dispose d'une sélection de tension automatique dans la plage CA de 110 V à 240 V.
IMPORTANT (for owners in the U.K.) Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this equipment. Getting Started If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or contact the local dealers in your area. BE SURE to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover.
o Para Brasil . Para Retirar a Bateria Recarregável Pressione botão e puxe a bateria para fora. Mounting to a firm place As the unit contain parts rotating at high speed, mount it on a firm place with sufficient strength to support the vibration and weight of the unit. Mass : Approx. 1.7 kg If the strength is weak, the vibration will cause fuzzy images on the monitor screen. In the worst scenario, the camera may even fall off and hit somebody, resulting in serious accidents.
Contents Getting Started Getting Started Safety Precautions ............................................ 5 Contents .......................................................... 12 Precautions ..................................................... 13 Names of Parts ................................................ 16 Basic System Diagram .................................... 20 Installation/Connection Mounting the Camera to the Ceiling Mount Bracket ............................................................
Precautions Installation Location o Be sure to install the camera horizontally. Carrying the Camera o Do not drop or hit this unit against a hard object when transporting. o Remove the connecting cables when transporting the unit. o When transporting the unit, turn off the power of the system. o Pack the unit with cushioning material so as to avoid shock when transporting. o Handle the unit with care and do not subject it to vibration or shock.
License Notices Getting Started o MPEG LA AVC THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
Getting Started o An afterimage can appear if you view a moving object on the monitor output, however this is not a malfunction. o Do not put anything into the camera unit. Metal and flammable items entering from the connectors can result in fire or electric shock. o The camera recorder may not show stable pictures for a few seconds immediately after the power is turned on, but this is not a malfunction. o Do not drop this unit or subject it to strong impact or vibration as it is a precision equipment.
Names of Parts A B C D E F G H I J Getting Started A B C . A Tally lamp Light turns on or goes off during external control. Turns on/off according to the menu setting and blinks depending on the status of this camera. B STANDBY lamp Lights up in green during standby. C POWER lamp Lights up in blue when the power is turned on. Terminal Section L K A J B I C . 16 H D Names of Parts EF G LINE OUT terminal LINE IN terminal DC 12V terminal LAN terminal USB 2.
Corresponding Pins between Camera and Windows DB-9 Windows DB-9 1.DTR 2.DSR 3.TXD 4.GND 5.RXD 6.GND 7.IR OUT 8.NC 1.CD 2.RXD 3.TXD 4.DTR 5.GND 6.DSR 7.RTS 8.CTS 9.RI . Corresponding Pins between Camera and Mini DIN . Camera Mini DIN 1.DTR 2.DSR 3.TXD 4.GND 5.RXD 6.GND 7.IR OUT 8.NC 1.DTR 2.DSR 3.TXD 4.GND 5.RXD 6.GND 7.NC 8.
Infrared Remote Control A Getting Started B C 2 3 4 REV 1 2 3 4 5 6 7 8 9 0 F1 D Q CAMERA SELECT 1 STD F2 F3 PRESET E P F4 HOME F MENU SLOW ZOOM O N M L RESET FAST G I H L/R SET BACKLIGHT P/T RST AUTO FAR NEAR FOCUS MANUAL K J . A STANDBY button Switches between the standby and normal modes. Memo : Power consumption in the standby mode is approximately half of that in the normal mode. B NUMBER button For preset configuration or invoking a preset number.
P # button To be used together with other buttons. Q CAMERA SELECT button Press the number of the camera you want to control using the infrared remote control. Memo : 0 The remote control unit makes use of 2 AAA dry-cell batteries. 0 Make sure to load the battery in the correct +/orientation. Image freeze feature Pressing the [F4] button freezes the video image and displays a “Freeze” caption at the top left corner of the screen for about 5 seconds.
Basic System Diagram 3.5 mm audio cable (Sold separately) Getting Started 3.5 mm audio cable (Sold separately) RS485 Cable (Sold Separately) RS232C Cable (Supplied) RS232 Cable (Sold Separately) 3G-SDI cable (Sold separately) HDMI cable (Sold separately) USB cable (Sold separately) LAN cable (Sold separately) Computer, TV, VCR with Audio Input Jack, AC adapter (Supplied) Router or Switch, Speaker Power cord (Supplied) Microphone, etc. DC 12V IN .
Mounting the Camera to the Ceiling Mount Bracket Memo : Check that the screws are tighten securely when mounting is completed. 0 Be sure to put on protective glasses to protect Memo : 0 The ceiling mount bracket is not necessary when the camera is installed on a desktop or attached to a tripod. 0 If necessary, make a hole (Φ40 mm) to route the connection cable and fall prevention wire (ceiling) into the ceiling. Caution : 0 The fall prevention wire (for ceiling) is not supplied.
Installing the Camera on the Ceiling 4 Use three M3 screws that come with the camera to attach Configure the video format settings using the SYSTEM SELECT switch before installing. 1 Remove the 4 feet from the bottom surface of the camera Installation/Connection . Fasten the drop prevention wire (sold separately) together with one of the screws. .
Installing the Camera on a Desktop Connect the cables after these procedures. Attaching the Camera to a Tripod Configure the video format settings using the SYSTEM SELECT switch before installing. 0 Attach a tripod using the screw hole at the bottom of this product. (1/4-20UNC, ISO1222 (6.35 ㎜)) 0 To prevent the camera recorder from falling off, which may result in injuries or damages, read the “INSTRUCTIONS” of the tripod to be used and make sure that it is securely attached.
Network Features Operating Environment Installation/Connection Operation has been verified for the following environments. 0 Computer 0 OS: Windows 10 Web browser: Google Chrome 0 OS: macOS 10.12. 6 Web browser: Google Chrome IP address settings There are two ways to configure the IP address of the camera. A Log in to the web page, and select [Network] B [LAN Settings] to make changes to the IP address, subnet mask and gateway. Click “Apply” to restart the camera. B Use “upgrade_standard.
3 After changing of “IP Address”, “NetMask”, and “GateWay” is complete, click the [Set] button. Confirming the Connection . 0 When the setting is successful, the following display appears and the camera recorder restarts. 2 Enter the user name and password. Enter the user name (jvc) and the password (initial password: 0000) on the login screen to display the Live View screen. Memo : The screen for changing the password is displayed when you log in for the first time. Please change the password. . .
Troubleshooting Problem Video image does not appear on the monitor Others Sometimes the video image is not displayed Video image becomes blurry when zoomed to the Tele end Video image does not appear on the Web browser Unable to access camera from the Web browser Action 0 Check to ensure that the power supply of the camera is properly connected, the power voltage is normal and the POWER lamp is on at all times. 0 Restart the camera and check whether the camera has been initialized.
Specifications Item [3G-SDI] terminal General Item Power Description DC 12 V (when an AC adapter is used) PoE 0.62 A (*1) 0.18 A (*2) Approx. 1.7 kg 0 °C to 40 °C (32 °F to 104 °F) Terminal Section Item [LINE IN] terminal [LINE OUT] terminal [RS485] terminal [RS232 IN] terminal [RS232 OUT] terminal [LAN] terminal Description Φ3.5 mm Line input Φ3.
Video Item Signal system Infrared Remote Control Description 3840x2160/30p, 25p, 29.97p 1920x1080/60p, 50p, 30p, 25p, 59.94p, 29.97p, 60i, 50i, 59.94i 1280x720/60p, 50p, 59.94p Network Item Video compression Video stream Others Main stream resolution Sub stream resolution Video bit rate Bit rate type Frame rate Audio compression Audio bit rate Protocols 28 Description H.264/H.
Dimensional Outline Drawing (Unit: mm) 164.5 Φ70.7 Others 141.5 168.4 . * The specifications and appearance of this product are subject to changes for further improvement without prior notice.
Software License Agreement Others The software embedded in the Product (hereinafter the “Licensed Software”) provided by JVCKENWOOD Corporation (hereinafter the “Licensor”) is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Article 9 Destruction of the Licensed Software If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination. Article 10 Export Restriction Article 11 Miscellaneous 1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force. 2.
. Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for countries that have adopted separate waste collection systems) Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste by products. Contact your local authority for details in locating a recycle facility nearest to you.
. Bu ürün 28300 sayılı Resmi Gazete’de yayımlanan Atik Elektrikli ve Elektronik Eşyalarin Kontrolü Yönetmeliğe uygun olarak üretilmiştir. Eski Elektrikli ve Elektronik Cihazların ve Pillerin İmhası Hakkında Bilgi (ayrı atık toplama sistemlerine sahip olan ülkelerde geçerlidir) Bu sembolü (üzeri çizili çöp bidonu) içeren ürün ve piller evsel atı k çöpleri ile birlikte atılamaz.
. KY-PZ400NWU KY-PZ400NBU KY-PZ400NWU/KY-PZ400NBU © 2021 JVCKENWOOD Corporation B5A-3984-00
