HD PTZ REMOTE CAMERA KY-PZ100WU / KY-PZ100WE KY-PZ100BU / KY-PZ100BE INSTRUCTIONS (Installation/IP Address Settings) Specifications and appearance of this unit are subject to change for further improvement without prior notice. Details For details on settings and operation, refer to “INSTRUCTIONS” on the website. Please check the latest INSTRUCTIONS, tools, etc. from the URL below. North America: http://pro.jvc.com/prof/main.jsp Europe: http://www.service.jvcpro.eu/public/ China: http://www.jvc.com.
FOR USA These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. IMPORTANT SAFEGUARDS Getting Started 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Safety Precautions FOR USA AND CANADA CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. POUR CANADA ATTENTION Getting Started RISQUE D’ELECTROCUTION NE PAS OUVRIR AVERTISSEMENT : POUR EVITER LES RISQUES D’INCENDIE OU D’ELECTROCUTION, NE PAS EXPOSER L’APPAREIL A LA PLUIE NI A L’HUMIDITE. ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION NE PAS OUVRIR LE BOITER. AUCUNE PIECE INTERIEURE N’EST A REGLER PAR L’UTILISATEUR. SE REFERER A UN AGENT QUALIFIE EN CAS DE PROBLEME.
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear). Do not block the ventilation holes. (If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.) No naked flame sources, such as lighted candles, should be placed on the apparatus.
IMPORTANT (for owners in the U.K.) Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this equipment. Getting Started If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or contact the local dealers in your area. BE SURE to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover.
o Para Brasil CAUTION: To avoid electric shock or damage to the unit, first firmly insert the small end of the power cord into the AC Adapter until it is no longer wobbly, and then plug the larger end of the power cord in to an AC outlet. FOR EUROPE WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Importer (EU only) 12 Priestley Way, London NW2 7BA, UNITED KINGDOM Importeur (Nur EU) Getting Started Konrad-Adenauer-Allee 1-11, 61118 Bad Vilbel, DEUTSCHLAND Importateur (EU uniquement) 7 Allee des Barbanniers, CS20034 92632 Gennevilliers Cédex, FRANCE Importatore (Solo EU) Via G. Sirtori 7/9, 20129 Milano, ITALIA Importador (Solamente EU) Ctra.
. ḏ䌰ἀ䒩㚠旑 ḏḨ⑂ᶮ䘅㚊⬴䇪岩 恩ṷ⎎䥱 乀嵰㜀久ṷ 㚻䬲 ⫧䱼习 ḥ㳂廭㋣◩ ṗ旅ṷ 摆 澐Qc澑 㯟 澐Ih澑 ȵ ȵ ȵ ȵ ȵ 㚊⬴䇪岩 擊 ⃮Ṹ摭 ⢛㸵俕剰 ⢛㸵ḍ剰愛 澐De澑 澐Ds)WJ*澑 )QCC* 澐QCEF澑 ȵ ȵ ȵ ȵ ȵ ȵ ȵ ȵ ȵ ȵ ȵ ȵ ȵ ȵ ȵ 㚭埩㞽㋯!TK0U22475!䘅奅⬛亗↷ɝ ȵ澢埩䢻学㚊⬴䇪岩⚩学恩ṷ㇁㚊⛈岩㛑㔚ᶮ䘅⎬慐⛈⚩!HC0U37683!奅⬛䘅 !!!!旑慐夂㯃Ṧᶌɝ 澢埩䢻学㚊⬴䇪岩兴⮒⚩学恩ṷ䘅㝑ᶁ⛈岩㛑㔚ᶮ䘅⎬慐崆ⅻ!HC0U37683 !!!!奅⬛䘅旑慐夂㯃ɝ For KY-PZ100WE, KY-PZ-100BE GB4943.1-2011 GB9254-2008 GB17625.
Consult your dealer as special technique is required when installing this product. Ensure that the fixing screws or nuts are tightened securely, otherwise, the unit may fall off. Mounting to a firm place Getting Started As the unit contain parts rotating at high speed, mount it on a firm place with sufficient strength to support the vibration and weight of the unit. Mass : Approx. 2.0 kg If the strength is weak, the vibration will cause fuzzy images on the monitor screen.
Contents Content of this manual Symbols used Getting Started Installation/Connection Mounting the Camera to the Ceiling Mount Bracket ............................................................ Installing the Camera on the Ceiling ................ Installing the Camera on a Desktop ................. Attaching the Camera to a Tripod .................... Connecting the Cables .................................... IP Address Settings ......................................... Using the IP Setting Tool .....
Precautions Installation Location o Be sure to install the camera horizontally. Getting Started Storage and Usage Locations o Allowable ambient temperature and humidity Be sure to use this unit within the allowable temperature range of 0 °C to 40 °C and a relative humidity of 30 % to 80 %. Using this unit at a temperature or humidity outside the allowable ranges could result not only in malfunction but also serious impact on the CMOS elements as small white spots may be generated.
microSDHC/microSDXC Cards Handling of microSD Cards o Do not remove the microSD card during data access (such as recording or formatting). And, do not turn off the power or remove the AC adapter during access. o Do not use or store the microSD card in a place that is subject to static electricity or electrical noise. o Do not place the microSD card near locations that are exposed to strong magnetic fields or radio waves.
Encryption in Network Connection o Wireless LAN connections make use of an encryption function. This encryption is designed for commercially-sold equipment, and it cannot be altered.
Getting Started o An afterimage can appear if you view a moving object on the monitor output, however this is not a malfunction. o Do not insert objects other than the memory card into the card slot. o Do not put anything into the camera unit. Metal and flammable items entering from the connectors can result in fire or electric shock. o Do not turn On/Off the power or remove the supplied AC adapter during recording.
Names of Parts Bottom Section Getting Started A B A C B D C E D E F . . A Camera head Rotates horizontally. B Lens section Rotates vertically. C Tally lamp Turns on/off according to the menu setting and blinks depending on the status of this camera. For details, refer to the “INSTRUCTIONS” downloadable from the URL stated on the cover page. D Infrared remote control sensor E POWER lamp Lights up as follows depending on the status of this camera.
Terminal Section 1 3 5 7 2 4 6 8 G A B C D Getting Started H [HDMI] HDMI terminal Output terminal for HDMI video signal. I [AUDIO IN] AUDIO input terminal For connecting the stereo mini plug. J [RS-422] RS-422 terminal For connecting the RS-422 cable. H I J K . E F . L M N A Anti-theft wire mounting hole B [LAN(PoE+)] LAN (PoE+) terminal For connecting the LAN cable. C microSD card slot For inserting the microSD card.
Infrared Remote Control A L B Getting Started C D E F G H M I J K N . A ZOOM button Pressing the button at the T end moves the zoom lens toward the telephoto range and the angle of view becomes narrower. Pressing the button at the W end moves the zoom lens toward the wide-angle range and the angle of view becomes wider. B AF button Sets the camera to the Auto Focus mode. C Pan/Tilt, Menu operation button Moves the display area. Moves the cursor when the menu is displayed.
About microSD Cards Compatible microSD Cards System HD Format Usable microSD Card Class 10 or higher Class 6 or higher Bit Rate QuickTime 50M 35M 28M 18M 5M Inserting an microSD Card Memo : 0 To use a microSDHC card, set [4GB File Spanning(SDXC)] to “On”. Caution : 0 Using cards other than those from Panasonic, TOSHIBA or SanDisk may result in recording failure or data loss. 0 If an UHS-I card with no classification indication is used, it may not be possible to perform recording.
DIP Switch Setting Configure the DIP switch before installing this unit. Getting Started ON ON 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 . Switch Bit Left 1 Function Select communication mode 2 to 4 Select protocol Description For selecting a communication mode. Remarks OFF: LAN; ON: Serial For selecting protocols.
o Connection example 1: IP control Switch Bit Left 1 Function Select communication mode 2 to 4 Select protocol KY-PZ100 KY-PZ100 KY-PZ100 Left Right ON RM-LP100 .1 Set to JVC (0). ON 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 .
Mounting the Camera to the Ceiling Mount Bracket 2 Place the supplied template against the ceiling, and fasten the ceiling mount bracket with four screws (M4 wooden screws: Φ4.1). 0 Be sure to put on protective glasses to protect Installation/Connection your eyes from falling objects when mounting the camera. 0 Be sure to place the base of the camera horizontally. The camera will not operate properly if it is slanted.
Installing the Camera on the Ceiling and the line indicated on the camera. Press the camera unit to insert, and then turn the camera clockwise. 5 Fix the camera and the fall prevention wire (ceiling) on the ceiling mount bracket using the provided screw (M3). Installation/Connection 1 Set the DIP switch. 0 Set the DIP switch prior to mounting the camera to the ceiling mount bracket. 2 Insert an microSD card. 0 Insert the card as necessary during installation.
Installing the Camera on a Desktop Attaching the Camera to a Tripod 0 Set the DIP switch prior to installing the camera. 0 Place the camera on a flat surface. 0 Be sure to place the base of the camera 0 Set the DIP switch prior to installing the camera. 0 Attach a tripod using the screw hole at the Installation/Connection horizontally. The camera will not operate properly if it is slanted. Memo : 0 The use of ceiling mount bracket is not required.
Connecting the Cables 1 Connect the power cable. 0 To supply power from an AC adapter, connect an AC adapter cable. 0 To supply power via PoE+, proceed to the next step without connecting an AC adapter cable. 0 Fix the AC adapter cable with a cable clamp. 6 Remove the protective sheet attached to the infrared remote control sensor. Caution : 0 For safety reasons, turn on the power only after ensuring that all the connections are in place.
IP Address Settings Using the IP Setting Tool 0 Connect the camera to be configured to the network via the LAN terminal. 0 Download the “IPSettingTool” from the URL stated on the cover page. . 0 Connect the computer for executing the Installation/Connection “IPSettingTool” to the network to establish communication with the camera to be configured. 1 Start up “IPSettingTool”. 2 Click the [Search] button. 0 If setting is successful, the search list display will be updated.
Confirm the connection Installation/Connection Operating Environment Operation has been verified for the following environments. 0 Computer 0 OS: Windows 7 Web browser: Google Chrome 0 OS: Windows 10 Web browser: Google Chrome 0 OS: Mac OS X 10.11 Web browser: Safari 1 Start up the web browser on the terminal you wish to connect to the camera recorder, and enter the [IP Address] in the address field. 0 (Example: http://192.168.0.25) Memo : 0 The default IP address of camera is http:// 192.168.0.10.
Troubleshooting Others Problem Symptom Action Power does not turn on. The AC adapter is not properly Check whether the AC adapter is properly connected. connected. There is problem in the connection 0 Check whether connection is established using a PoE+ with the PoE+ (IEEE802.3at Type2) power supply device. (IEEE802.3at Type2) power supply device and a LAN cable of Category 5e or higher.
Problem Cannot connect to wireless LAN. Symptom Wireless LAN is not correctly configured. The passphrase is incorrect. Unable to start recording. The recording mode is not supported by the microSD card. The actual recording time is shorter than the estimated time. The clips cannot be [Clip Server] is not correctly uploaded to the FTP configured. server. The size of the recorded clip has exceeded 64 GB. An FTP transfer error message is displayed. The maximum size of the recorded clip is 64 GB.
Specifications General Item Power Description DC 12 V (when an AC adapter is used) DC 42 V to 57 V (when PoE+ power supply is used) 1.2 A (*1) 0.4 A (*2) Approx. 2.0 kg 0 °C to 40 °C Others Current consumption Mass Allowable operating temperature 30 %RH to 80 %RH (No Allowable condensation) operating humidity -20 °C to 50 °C Allowable storage temperature Dimensions (W 154 mm × 200.7 mm × 191 mm × H × D) *1 During recording in the factory settings when an AC adapter is in use.
Video/Audio Infrared Remote Control Item Description Remote control Infrared type system Battery CR2025 (DC 3.0 V) Battery life Approx. 1 year (varies with the frequency of use) Operating 7 m (horizontal distance from distance the front) 0 °C to 40 °C Allowable operating temperature Dimensions (W 42 mm × 14.6 mm × 90 mm × H × D) Mass Approx.
Dimensional Outline Drawing (Unit: mm) 148 Others 54 1.2 49.2 137 199.5 Φ1 154 . 172 182 191 * The specifications and appearance of this product are subject to changes for further improvement without prior notice.
Software License Agreement Article 1 General Provision The Licensor shall grant to the User a nonexclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User (the country where the User bought the Product (hereinafter the “Country”)). Article 2 License 1. The license granted under this Agreement shall be the right to use the Licensed Software in the Product. 2.
Article 8 Termination In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.
Important Notice concerning the Software Software License Attached to the Product : A Start up Live View. B Open the [MENU] tab and click the [MENU] button to display the camera menu. C Select [Main Menu] B [System] B [System Information] B [Open Source License].
B5A-1712-00 © 2016 JVC KENWOOD Corporation KY-PZ100WU / KY-PZ100WE / KY-PZ100BU / KY-PZ100BE HD PTZ REMOTE CAMERA .