KW-V660BT KW-V66BT MONITOR WITH DVD RECEIVER INSTRUCTION MANUAL • Updated information (the latest Instruction Manual, system updates, new functions, etc.) is available from . © 2020 JVCKENWOOD Corporation !B5H-0357-03_JVC_KWV_K_En.
Contents Before Use 4 Tuner 25 Precautions.................................................................... 4 Tuner Basic Operation.............................................25 How to read this manual.......................................... 5 Memory Operation...................................................26 Selecting Operation.................................................26 Basic Operations 6 Functions of the Buttons on the Front Panel.... 6 Turning on the Unit....................
Controlling Audio 48 Speaker/ X’over setup..............................................48 Controlling General Audio.....................................49 Equalizer Control.......................................................50 Volume Offset.............................................................51 Sound Effect................................................................51 Listening Position/ DTA...........................................
Before Use Before Use Precautions # WARNINGS ÑÑTo prevent injury or fire, take ÑÑHow To Reset Your Unit • If the unit or the connected unit fails to operate properly, reset the unit. Press the button. The unit returns to factory settings. the following precautions: • To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. • Do not watch or fix your eyes on the unit’s display when you are driving for any extended period.
Before Use ÑÑPrecautions on handling discs How to read this manual • Do not touch the recording surface of the disc. • Do not stick tape etc. on the disc, or use a disc with tape stuck on it. • Do not use disc type accessories. • Clean the disc from the center toward the outside rim. • When removing a disc from this unit, pull it out horizontally. • If the disc center hole or outside rim has burrs, use the disc only after removing the burrs with a ballpoint pen etc.
Basic Operations Basic Operations Functions of the Buttons on the Front Panel Turning on the Unit The method of turning on is different depending on the model. 1 2 1 Press the [ ] button. 3 4 5 6 7 hh The unit is turned on. NOTE • The panels shown in this guide are examples used to provide clear explanations of the operations. For this reason, they may be different from the actual panels. Name ●● To turn off the unit: 1 Press the [ ] button for 1 second.
Basic Operations Getting Started ■■ [Camera] Set the parameters for the camera. 1 Touch [Camera]. 2 Set each item and touch [ ]. For detailed operation, see Camera Setup (P.42). Initial setup Perform this setup when you use this unit first time. 1 ■■ [DEMO] Set the demonstration mode. Default is “ON”. 1 Touch [DEMO] and set [ON] or [OFF]. Set each item as follows. 2 ■■ [Language] Select the language used for the control screen and setting items. Default is “[American English(en)]”.
Basic Operations 3 Touch [User Interface]. Adjusting the volume To adjust the volume (0 to 40), Press [+] to increase, and press [−] to decrease. Holding [+] increases the volume continuously to level 15. hh User Interface screen appears. 4 Touch [Clock Adjust]. Touch screen operations To perform operations on the screen, you need to touch, touch and hold, flick or swipe to select an item, display setting menu screen or to change the page, etc.
Basic Operations Display the HOME screen Gesture Touch Control: You can also control playback by moving your finger on the touch panel as follows (for some sources, the gesture control is not available). • Sliding the finger towards up/down: - Functions same as pressing [ ] / [ ] (Media) in the USB Control screen. - For the Tuner, tuner preset broadcast stations are switched. • Sliding the finger towards left/right: Functions same as pressing [E] / [F].
Basic Operations Select the playback source 1 To select the playback source on the HOME screen Touch [ ] on the HOME screen. From the screen, you can select the following sources and functions. • Switches to the Apple CarPlay screen from the connected iPhone. (P.19) • Switches to the Android Auto screen from the connected Android smartphone. (P.20) It is necessary to connect Android smartphone compatible with Android Auto and to set [Mode] to [Android Auto]. (P.
Basic Operations Customize Short-cut buttons on HOME screen 3 Secondary screen You can arrange the position of the source icons as you like. 1 Touch [ 2 Touch and hold the icon which you want to move to go into the customizing mode. 3 ] on the HOME screen. Drag it where you want to move. • [ ]/[ ] : The Secondary screen changes every time you touch it. You can also change the Secondary screen by flicking left or right on the screen. • Indicators: Displays the current source condition and so on.
Basic Operations FUNCTION screen 1 1 Press the [FNC] button. hh FUNCTION screen appears. 2 ●● To turn on the screen Touch the display. List screen There are some common function keys in the list screens of most sources. 1 Touch to display the FUNCTION screen. 2 3 The contents of the menu are as follows. • Displays the SETUP Menu screen. (P.44) • Displays the APP (Apple CarPlay/ Android Auto) screen. (P.19) • Displays the Screen Adjust screen. (P.44) • Displays the view camera. (P.
Disc Disc Playing a disc ÑÑInsert a disc 1 Insert the disc into the slot. DVD/VCD Basic Operation Most functions can be controlled from the source control screen and playback screen. NOTE • The screen shot below is for DVD. It may be different from the one for VCD. 1 When the operation buttons are not displayed on the screen, touch 7 area. Control screen hh The unit loads the disc and playback starts. 1 2 3 ÑÑEject a disc 1 2 Press the [FNC] button. hh FUNCTION screen appears. Touch [ ].
Disc 2 Play mode indicator/Playing time 5 Indicator Items • D, B, I, etc.: Current play mode indicator Meanings of the icons are as follows: D (play), B (fast forward), A (fast backward), I (stop), R (resume stop), H (pause), (slow playback), (slow reverse playback). • [IN]: Disc insertion status. White: A Disc is inside the unit. Orange: Disc player failure. 3 Information display area Displays the following information. • [Hide]: Hides the control screen. ] : Repeats the current content.
Disc ÑÑFunction panel 1 Touch on the left side of the screen. DVD VCD Music CD/Disc media Basic Operation Most functions can be controlled from the source control screen and playback screen. NOTE The functions of each key are as follows. [ ] [ ] : Fast-forwards or fast-backward the disc. Each time you touch the key, the speed changes. [ ] [ ] (DVD only): Plays in slow motion forward or backward. [I]: Stops playback. Touching twice will play the disc from the beginning when you play it next time.
Disc 2 [ ]/[ DVD Disc Menu Operation ] ] : Repeats the current track. Each time •[ you touch the key, repeat mode switches in the following sequence; Track/File repeat ([ ]), Repeat all ([ ]) ] : Randomly plays all tracks in current disc. •[ Each time you touch the key, random mode switches in the following sequence; Track random ([ ]) (Music CD only), Random off ([ ]) You can set up some functions using the DVDVIDEO disc menu. 1 Touch the framed area during playback.
Disc ■■ To switch among picture angles Touch [Angle]. Each time you touch this key, picture angles are switched. * These keys may not function depending on the disc. DVD Setup You can set up the DVD playback functions. 1 Touch the framed area during playback. ÑÑHighlight control Highlight control lets you control the DVD menu by touching the menu key directly on the screen. 1 2 Touch [Highlight] on the Menu Control screen. 2 Touch your desired item on the screen.
Disc ■■ [Screen Ratio] Sets the screen display mode. [16:9 ](Default): Displays wide pictures. [4:3LB]: Displays wide pictures in the Letter Box format (having black stripes at the top and bottom of screen). [4:3PS]: Displays wide pictures in the Pan & Scan format (showing pictures cut at the right and left ends). ÑÑLanguage setup This setting is for the languages used for the menu, subtitle, and voice. 1 2 Touch the desired item; [Menu Language], [Subtitle Language], [Audio Language].
APPS APPS Apple CarPlay Operation Apple CarPlay is a smarter, safer way to use your iPhone in the car. Apple CarPlay takes the things you want to do with iPhone while driving and displays them on the screen of the product. You can get directions, make calls, send and receive messages, and listen to the music from iPhone while driving. You can also use Siri voice control to make it easier to operate iPhone. For details about Apple CarPlay, visit https://www.apple.com/ios/carplay/.
APPS Android Auto™ Operation Android Auto enables you to use functions of your Android smartphone convenient for driving. You can easily access route guidance, make calls, listen to music, and access convenient functions on the Android smartphone while driving. For details about Android Auto, visit https://www.android.com/auto/ and https://support.google.com/androidauto. Compatible Android smartphone You can use Android Auto with Android smartphone of Android version 5.0 or later.
APPS USB Mirroring Operation (Android only) You can display and control the App on the unit while your smartphone is connected to the USB terminal. ÑÑPreparation 1 2 ÑÑCompatible Android smartphone • Android version 7.0 or later • Linux Kernel version 3.5 or later • Bluetooth support NOTE • This unit may not work for some Android smartphone's. Download Mirroring App from the Google Play. Install the latest version of the Mirroring application “Mirroring OA for JVC” on your Android.
USB USB Connecting a USB device 1 Connect the USB device with the USB cable. (P.57) USB Basic Operation Most functions can be controlled from the source control screen and playback screen. Control screen 1 2 3 4 Press the [ Touch [ 4 ]. Touch [USB]. (P.10) Press the [ Touch [ 3 ] button. ÑÑDisconnect the USB device 1 2 3 4 2 5 6 7 Open the drawer 5 ] button. 4 ]. Touch a source other than [USB]. Detach the USB device.
USB 2 [ ]/[ Video screen ] ] : Repeats the current track/folder. Each •[ time you touch the key, repeat mode switches in the following sequence; File repeat ([ ]), Folder repeat ([ ]), Repeat all ([ ]) ] : Randomly plays all tracks in current •[ folder. Each time you touch the key, random mode switches in the following sequence; File random ([ ]), Random off ([ ]) 3 Track information Displays the information of the current file.
USB Search Operation You can search music or video files by the following operations. 1 2 Touch [1]. 3 Select the list type. Touch [S]. ÑÑLink search You can search a file of same artist/album/genre as the current track. 1 2 ÑÑCategory search You can search a file by selecting category. 1 2 Touch [Category List]. 3 Touch the desired category. Touch the desired tag type. You can select from artist, album and genre. hh The list corresponding to your selection appears.
Tuner Tuner Tuner Basic Operation 3 Operation keys Most functions can be controlled from the source control screen. To enter Tuner source, touch [Tuner] icon in the source selection screen. (P.10) Control screen 1 • [E] [F] : Tunes in a station. The method of frequency switching can be changed (see 2 in table). •[ ] : Touch to mute or not to mute. 4 Preset list • Touch on the right side of the screen to display the Preset list. Touch again to close the list. • Recalls the memorized station.
Tuner Memory Operation Selecting Operation ÑÑAuto memory ÑÑPreset select You can store stations with good reception in memory automatically. You can list and select memorized station. 1 Touch desired band key. 2 Touch [ ] on the left side of the screen. Touch [AME]. 1 Touch [ ] on the right side of the screen. Select a station from the list. ÑÑSearch by program type (FM only) You can tune to a station with a specific program type when listening to FM.
Tuner Traffic Information (FM only) You can listen and watch the traffic information automatically when a traffic bulletin starts. However, this feature requires a Radio Broadcast Data System that includes the TI information. 1 Tuner Setup You can set tuner related parameters. 1 2 Touch [ ] on the left side of the screen. Touch [TI]. Touch [ ]. Touch [ ] on the left side of the screen. Touch [SETUP]. hh Tuner SETUP screen appears. hh Traffic information mode is set.
SiriusXM® SiriusXM® SiriusXM® Basic Operation Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com. To listen to the SiriusXM source, touch the [SiriusXM] icon on the source selection screen. (P.
SiriusXM® 3 Artwork / Function panel • Displays the album artwork for most SiriusXM music channels. • Touch [ ] of the screen to display the function panel. Touch [ ] to close the panel. –– [Direct Channel]: Touch and enter the desired number. For details, see Direct search (P.30). –– [SETUP]: Touch to display the SiriusXM SETUP screen. For details, see SiriusXM Setup (P.31). –– [Replay/Live]: Touch to turn on or off the replay mode. See Replay (P.31).
SiriusXM® Direct search You can tune in a channel directly. 1 2 Touch [ ] on the left side of the screen. Touch [Direct Channel]. Category/Channel search You can specify the desired category and select a channel. 1 Touch [1]. 2 Select a category. Enter the channel number and touch [Enter]. hh Channel list appears. 3 Select the desired content from the list. *1 NOTE • To clear the number you entered, touch [BS]. *1 Select a desired item ([Info], [CH Name], [Artist], [Title]).
SiriusXM® Replay You can replay the last 60 minutes of the program from the current channel. 1 SiriusXM Setup 1 Touch [ ] on the left side of the screen. Touch [SETUP]. Touch [L] or [Replay] on the function panel. ■■ [E] [F] Press to skip to the previous/next track. Press and hold to rewind or fast forward. ■■ [DH] Plays or pauses. ■■ Replay time bar/Play mode indicator Displays the recorded data capacity and playback position. [D], [B], etc.
SiriusXM® ÑÑParental code ÑÑParental Control You can set a SiriusXM parental code for Parental Control. The Parental Control feature allows you to limit access to any SiriusXM channels, including those with mature content. When enabled, the Parental Control feature requires you to enter a Parental Code to tune to the locked channels. 1 Touch [Parental Code] on the SiriusXM SETUP screen. hh Parental Code Set screen appears. NOTE • The code number is set to “1111” as default.
SiriusXM® When selecting [User] 4 This allows you to limit access to any SiriusXM channel (Parental Lock Channel). 1 Touch [Parental Lock Channel Selection] on the SiriusXM SETUP screen. hh Parental Lock Code screen appears. Touch each channel on the list and set to [ON] or [OFF]. [ON]: Locks the channel. [OFF]: Unlocks the channel. *1 NOTE • You need to set up a parental code beforehand as stated in Parental code (P.32).
Bluetooth Control Bluetooth Control Using the Bluetooth function, various functions can be used: listening to the audio file, making/ receiving a call. Information for using Bluetooth® devices Bluetooth is a short-range wireless radio communication technology for mobile devices such as mobile phones, portable PCs, and other devices. Bluetooth devices can be connected without cables and communicate with each other.
Bluetooth Control Register from the Bluetooth device It is necessary to register the Bluetooth audio player or cell-phone to this unit before using the Bluetooth function. You can register up to 7 Bluetooth devices. Bluetooth Setup 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. NOTE • Up to 7 Bluetooth devices can be registered. If an attempt is made to register the 8th Bluetooth device, the Bluetooth device connected on the earliest date will be deleted to register the 8th one.
Bluetooth Control ÑÑConnect the Bluetooth device 1 Touch [Select Device] in the Bluetooth SETUP screen. Playing Bluetooth Audio Device Most function can be controlled from the source control screen. To enter Bluetooth source, touch [BT Audio] icon in the source selection screen. (P.10) ÑÑBluetooth basic operation Control screen 5 2 Touch [ ] you want to connect. 1 2 4 3 1 Device name/ [ NOTE • If the icon is lighted, it means that the unit will use that device.
Bluetooth Control 4 Function panel 2 Touch on the left side of the screen to display the function panel. Touch again to close the panel. • [BT DEVICE CHANGE] : Selects the device to connect via Bluetooth audio (A2DP) or APP (SPP). See Connect the Bluetooth audio (P.37). Touch the device name you want to connect. 5 Play mode indicator/ Playing time [D], [H]: Current play mode indicator The meanings of each icon are as follows; [D] (play), [B] (fast forward), [A] (fast backward), [H] (pause).
Bluetooth Control Using Hands-Free Unit You can use telephone function by connecting the Bluetooth telephone to this unit. NOTE • While Apple CarPlay or Android Auto is being connected, Bluetooth Hands-Free function cannot be used. Only Apple CarPlay or Android Auto Hands-Free function can be used. ●● Bluetooth SETUP 1) Touch [ ]. Bluetooth SETUP screen appears. NOTE • The status icons such as battery and antenna displayed may differ from those displayed on the cell-phone.
Bluetooth Control Call using the preset number ÑÑVoice Recognition 1 2 You can access the voice recognition function of the cell-phone connected to this unit. You can search the cell-phone phonebook by voice. (The functionality depends on the cell-phone.) Touch [ ]. Touch the Name or phone number. 1 Press the [ ] button. hh Voice Recognition screen appears. 2 Call using the phonebook 1 2 Touch [ 3 Select the phone number from the list. ]. Start speaking.
Bluetooth Control ÑÑReceive a call 1 ÑÑOperations during a call Touch [ ] to answer a phone call or [ to reject an incoming call. ] ●● Adjust the receiver volume Press the [−] or [+] button. NOTE • While monitoring the view camera, this screen does not appear even if a call comes in. To display this screen, return the shift knob of car to the driver position. To end call 1 While talking, touch [ ]. ●● Output the dial tone Touch [DTMF] to display the tone input screen.
Bluetooth Control ÑÑPhone number preset ■■ [Delete] To delete a preset number, touch [Delete] and then touch [Yes] on the confirmation screen. You can register frequently used phone numbers to this unit. 1 2 Touch [ ]. Touch [Edit]. ÑÑPhonebook transfer You can transfer the phonebook in your Bluetooth smartphone via PBAP. 1 2 3 Touch [ ]. Touch [ ]. Select where to preset. hh The phonebook data transmission starts.
Other External Components Other External Components ÑÑCamera Setup View Camera NOTE • To connect a camera, see P.57. • To use a rear view camera, a REVERSE lead connection is required. (P.57) • The rear view screen is displayed when you shift the gear to the reverse (R) position. 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh SETUP Menu screen appears. 3 Touch [Camera]. ÑÑDisplay the camera screen 1 Press the [FNC] button. hh FUNCTION screen appears.
Other External Components To adjust the parking guidelines NOTE • Install the rear view camera in the appropriate position according to the instructions supplied with the rear view camera. • When adjusting the parking guidelines, make sure to use the parking brake to prevent the car from moving. 1 Touch [ON] of [Parking Guidelines] in the Camera screen. (P.42) 2 Touch [Guidelines SETUP] in the Camera screen. 3 Adjust the parking guidelines by selecting the [ ] mark.
Setting Up Setting Up Monitor Screen Setup You can adjust image quality in video screen. 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. System Setup 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh Screen Control screen appears. 3 Adjust each item as follows. ■■ [Contrast] / [Brightness] / [Color] / [Tint] Adjusts each item. NOTE • Adjusting items are different depending on the current source. hh See the following section for each setting.
Setting Up User Interface Setup Special Setup You can setup user interface parameters. You can setup Special parameters. 1 Press the [FNC] button. hh FUNCTION screen appears. 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh SETUP screen appears. 2 Touch [ ]. hh SETUP screen appears. 3 Touch [User Interface]. 3 Touch [Special]. hh User Interface screen appears. 4 Set each item as follows. hh Special screen appears.
Setting Up Display Setup 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh SETUP screen appears. 3 Touch [Display]. To register original image You can load an image from the connected USB device and set it for the background image. Before operating this procedure, it is necessary to connect the device which has the image to load. 1 Touch [User1 Select] or [User2 Select] in the Background screen. 2 Select the image to load. 3 Touch [Enter]. hh Display screen appears.
Setting Up AV Setup You can set AV parameters. 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh SETUP screen appears. 3 Touch [AV]. hh AV screen appears. 4 Set each item as follows. ■■ [AV-OUT] Specify whether to output the current source signal from the VIDEO OUT terminal. “[ON]”/ “[OFF]” (Default) NOTE • Images can be output only from the AV IN, USB (video file) and DISC (DVD video) source.
Controlling Audio Controlling Audio You can adjust the various settings such as audio balance or subwoofer level. 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh See the following section for each setting. • Set up speaker/ X’over (P.48) • Controlling equalizer (P.50) • Set listening position/ DTA (P.52) • Controlling general audio (Fader / Balance) (P.49) • Set volume offset (P.51) • Set sound effect (P.51) Speaker/ X’over setup 1 Press the [FNC] button.
Controlling Audio ■■ [Tweeter] (Only for Front) You can set the tweeter when you are selecting front speakers. [None], [Small], [Medium], [Large] ■■ [TW] (Tweeter) [Gain]*2 Adjusts the tweeter level. (When front is selected on Speaker Select screen) ■■ [Phase Inversion]*3 Sets the phase of subwoofer output. Check [Phase Inversion] to shift the phase 180 degrees. (When subwoofer is selected on Speaker Select screen) ■■ [Xʼover] Displays the speaker crossover setup screen.
Controlling Audio Equalizer Control ■■ [SW Level] Adjusts the subwoofer volume. You can adjust equalizer by selecting the optimized setting for each category. ÑÑRecall the EQ curve 1 1 2 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh Audio screen appears. 3 Touch [Equalizer]. 4 Touch the screen and set the Graphic Equalizer as desired. Touch [Preset Select]. Select EQ curve. ÑÑSave the EQ curve 1 2 3 Adjust the EQ curve. Touch [Memory]. Select where to save.
Controlling Audio Volume Offset Finely adjust the volume of the current source to minimize the difference in volume between different sources. Sound Effect You can set sound effects. 1 Press the [FNC] button. hh FUNCTION screen appears. Press the [FNC] button. hh FUNCTION screen appears. 2 2 Touch [ ]. hh Audio screen appears. Touch [ ]. hh Audio screen appears. 3 Touch [Sound Effect]. 3 Touch [Volume Offset]. 4 Set each item as follows. 1 4 Touch [+] or [−] to adjust the level.
Controlling Audio Listening Position/ DTA Adjust the sound delay time as nearer speakers to the selected seat have more delay time, so that the sound from each speaker arrive a listener at the same time. 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh Audio screen appears. 3 Touch [Position/DTA]. 4 Select listening position from [Front R] (Right front), [Front L] (Left front), [Front All] (All front), and [All].
Remote control Remote control This unit can be operated using the remote control RM-RK258 (optional accessory). Functions of the Remote control Buttons Key Name Function [DIRECT] Switches to the direct search mode. For details on the direct search mode, see Direct search mode (P.53). [ASPECT] Changes the aspect ratio. Numeric Keypad Specifies the number to search in direct search. For details on the direct search mode, see Direct search mode (P.53).
Connection/Installation Connection/Installation Before Installation Before installation of this unit, please note the following precautions. # WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Connection/Installation ÑÑSupplied accessories for Installing the unit installation 1 ÑÑNon-Japanese cars 2 (3 m) x1 x1 3 4 (2 m) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. x1 x1 6 5 (M5 × 6 mm) (M5 × 8 mm) x6 7 x6 8 x1 NOTE • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Connection/Installation ÑÑMicrophone unit ÑÑRemoving the unit 1) Check the installation position of the microphone (accessory 1). 2) Clean the installation surface. 3) Remove the separator of the microphone (accessory 1), and stick the microphone to the place shown below. 4) Wire the microphone cable up to the unit with it secured at several positions using tape or other desired method. 5) Adjust the direction of the microphone (accessory 1) to the driver.
Connection/Installation ÑÑConnecting wires to terminals USB terminal[1] (1.0 m) USB device[2] 5V=1.5A Cap SiriusXM Connect Vehicle Tuner connector Sirius XM For more information on how to install the SiriusXM Connect Vehicle tuner, consult the installation guide included with the tuner. For best safety, be sure to connect the parking sensor. PRK SW Light Green (Parking sensor wire) Accessory 3: Parking Extention cable Connect to the vehicle’s parking brake detection switch harness.
Connection/Installation ÑÑConnecting an iPhone/Android Android smartphone[2] USB cable[2] 1 3 5 7 2 4 6 8 1 3 5 7 2 4 6 8 iPhone[2] Lightning connector Accessory 7 Accessory 8 KS-U62 (0.8m)[3] Speaker impedance: 4-8 Ω White White/Black Gray Gray/Black Green Green/Black Purple Purple/Black To front left speaker USB terminal[1] (1.0 m) 5V=1.5A To front right speaker Cap To rear left speaker To rear right speaker SB maximum power supply current : U DC 5 V = 1.
Troubleshooting Troubleshooting Problems and Solutions If any trouble occurs, first check the following table for possible problems. NOTE • Some functions of this unit may be disabled by some settings made on this unit. • What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. ÑÑAbout settings • Cannot set up the subwoofer. • Cannot set up subwoofer phase. • No output from the subwoofer. • Cannot set up the low pass filter.
Troubleshooting Mecha Error The disc player is malfunctioning. Eject the disc and try inserting it again. Contact the JVC dealer if this indicator continues blinking or the disc cannot be ejected. [Disc Error An unplayable disc is inserted. Change the disc. See Playable Media and Files (P.61). [Read Error] The disc is quite dirty. Clean the disc. See Precautions on handling discs (P.5). Disc is upside down. Load the disc with the labeled side up.
Appendix Appendix Playable Media and Files You can play various kinds of media and files on this unit. ÑÑList of playable discs NOTE • 8-cm (3 inch) discs cannot be used.
Appendix ÑÑAbout files The following audio and video files are supported. ■■Playable Audio files Format AAC-LC (.m4a) MPEG2/4 AAC LC HE-AAC(V1,V2) MP3 (.mp3) MPEG 1/2 Audio Layer 3 WMA (.wma) Windows Media Audio Standard L3 profile (Version 7,8,9) Linear PCM RIFF waveform Audio Format (WAVE) (.wav) FLAC (.flac) flac Vorbis (.
Appendix Region Codes in the World The DVD players are given a region code according to the country or area it is marketed, as shown in the following map. 1 5 2 6 1 2 3 1 4 5 2 4 ■■DVD disc marks ALL Indicates a region number. The discs with this mark can be played with any DVD player. 8 ■■Operation regulatory marks With this DVD, some functions of this unit such as the play function may be restricted depending on the location where the DVD is playing.
Appendix DVD Language Codes Code Language Code Language Code Language [aa] [ab] [af] [am] [ar] [as] [ay] [az] [ba] [be] [bg] [bh] [bi] [bn] [bo] [br] [ca] [co] [cs] [cy] [da] [de] [dz] [el] [en] [eo] [es] [et] [eu] [fa] [fi] [fj] [fo] [fr] [fy] [ga] [gd] [gl] [gn] [gu] [ha] [he] [hi] [hr] [hu] [hy] [ia] [ie] Afar Abkhazian Afrikaans Amharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish German Bhutan
Appendix Specifications ■■Monitor section Picture Size : 6.75 inches (diagonal) wide : 151.8 mm (W) × 79.7 mm (H) 5-15/16 × 3-1/8 inch Display System : Transparent TN LCD panel Drive System : TFT active matrix system Number of Pixels : 1,152,000 (800H × 480V × RGB) Effective Pixels : 99.
Appendix ■■DSP section ■■Video section Graphics equalizer Band: 13 Band Frequency (BAND1 – 13) : 62.5/ 100/ 160/ 250/ 400/ 630/ 1k/ 1.6k/ 2.5k/ 4k/ 6.3k/ 10k/ 16k Hz Color System of External Video Input : NTSC/ PAL Gain : -9/ -8/ -7/ -6/ -5/ -4/ -3/ -2/ -1/ 0/ +1/ +2/ +3/ +4/ +5/ +6/ +7/ +8/ +9 dB 2Way X'Over High pass filter Frequency: Through, 30/ 40/ 50/ 60/ 70/ 80/ 90/ 100/ 120/ 150/ 180/ 220/ 250 Hz Slope: -6/ -12/ -18/ -24 dB/ Oct.
Appendix About this Unit ■■Copyrights • The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. • Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby Laboratories.
Appendix STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. • libvorbis Copyright (c) 2002-2008 Xiph.org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: –– Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Appendix ■■FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix ■■Informação sobre a eliminação de pilhas Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador. A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.
Important Notice on Software EULA ÑÑSoftware License on This Product ÑÑSoftware License Agreement The software embedded in this product comprises a number of independent software components, each of which is copyrighted by JVCKENWOOD Corporation or by a third party. JVCKENWOOD Corporation (hereinafter called “Licensor”) holds either the copyright to the embedded software or the right to sublicense it. This agreement establishes the conditions under which the customer uses this “Licensed Software.
Article 3 (Terms of License) Article 8 (Cancellation of the Agreement) 1. In assigning this product, User may not retain the original copy of the embedded Licensed Software (including associated literature, updates and upgrades) and any duplicates and associated literature with regard to the license to use Licensed Software. User may transfer Licensed Software only to the condition of binding the assignee to abide by the terms of this Software License Agreement.
!B5H-0357-03_JVC_KWV_K_En.
KW-V660BT KW-V66BT MONITOR WITH DVD RECEIVER Quick Start Guide MONITEUR AVEC RÉCEPTEUR DVD Guide de démarrage rapide MONITOR CON RECEPTOR DVD Guía de inicio rápido • Updated information (the latest Instruction Manual, system updates, new functions, etc.) is available from • Les informations les plus récentes (dernier mode d'emploi, mises à jour du système, nouvelles fonctions, etc.
Important Notice on Software EULA ÑÑSoftware License on This Product ÑÑSoftware License Agreement The software embedded in this product comprises a number of independent software components, each of which is copyrighted by JVCKENWOOD Corporation or by a third party. JVCKENWOOD Corporation (hereinafter called “Licensor”) holds either the copyright to the embedded software or the right to sublicense it. This agreement establishes the conditions under which the customer uses this “Licensed Software.
Article 3 (Terms of License) Article 8 (Cancellation of the Agreement) 1. In assigning this product, User may not retain the original copy of the embedded Licensed Software (including associated literature, updates and upgrades) and any duplicates and associated literature with regard to the license to use Licensed Software. User may transfer Licensed Software only to the condition of binding the assignee to abide by the terms of this Software License Agreement.
Before Use Contents Before Use...................................................................... 4 About the Quick start guide............................................................4 How to read this manual...................................................................4 Precautions.................................................................................................5 Basic Operations..........................................................
Before Use Precautions # WARNINGS ÑÑHow To Reset Your Unit • If the unit or the connected unit fails to operate properly, reset the unit. Press the button. The unit returns to factory settings. ÑÑTo prevent injury or fire, take the following precautions: • To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. • Do not watch or fix your eyes on the unit’s display when you are driving for any extended period.
Before Use ÑÑPrecautions on handling discs • Do not touch the recording surface of the disc. • Do not stick tape etc. on the disc, or use a disc with tape stuck on it. • Do not use disc type accessories. • Clean the disc from the center toward the outside rim. • When removing a disc from this unit, pull it out horizontally. • If the disc center hole or outside rim has burrs, use the disc only after removing the burrs with a ballpoint pen etc. • Discs that are not round cannot be used.
Basic Operations Basic Operations Functions of the Buttons on the Front Panel Turning on the Unit 1 Press the [ ] button. 1 2 3 4 5 6 7 hh The unit is turned on. ●● To turn off the unit: NOTE • The panels shown in this guide are examples used to provide clear explanations of the operations. For this reason, they may be different from the actual panels. 1 Press the [ ] button for 1 second.
Basic Operations Getting Started ■■ [Camera] Set the parameters for the camera. 1 Touch [Camera]. 2 Set each item and touch [ ]. For detailed operation, see Instruction Manual. Initial setup Perform this setup when you use this unit first time. 1 ■■ [DEMO] Set the demonstration mode. Default is “ON”. 1 Touch [DEMO] and set [ON] or [OFF]. Set each item as follows. 2 ■■ [Language] Select the language used for the control screen and setting items. Default is “[American English(en)]”.
Basic Operations 3 Touch [User Interface]. Adjusting the volume To adjust the volume (0 to 40), Press [+] to increase, and press [−] to decrease. Holding [+] increases the volume continuously to level 15. hh User Interface screen appears. 4 Touch [Clock Adjust]. Touch screen operations To perform operations on the screen, you need to touch, touch and hold, flick or swipe to select an item, display setting menu screen or to change the page, etc.
Basic Operations Display the HOME screen Gesture Touch Control: You can also control playback by moving your finger on the touch panel as follows (for some sources, the gesture control is not available). • Sliding the finger towards up/down: - Functions same as pressing [ ] / [ ] (Media) in the USB Control screen. - For the Tuner, tuner preset broadcast stations are switched. • Sliding the finger towards left/right: Functions same as pressing [E] / [F].
Basic Operations Select the playback source To turn off the AV source 1 1 Touch [ 2 Touch [AV Off]. Touch [ ] on the HOME screen. From the screen, you can select the following sources and functions. ] on the HOME screen. • Switches to the Apple CarPlay screen from the connected iPhone. • Switches to the Android Auto screen from the connected Android smartphone. It is necessary to connect Android smartphone compatible with Android Auto and to set [Mode] to [Android Auto].
Basic Operations Source control screen descriptions 4 [Û] Touch to display the Hands Free screen. (P.21) When connecting as Apple CarPlay or Android Auto, it works as a phone provided in Apple CarPlay or Android Auto. There are some functions which can be operated from most screens. Indicators 1 2 3 4 Sub menu 1 [ ]/[ ] Connected Bluetooth device information. 2 All sources icon Displays all sources. 3 Secondary screen • [ ]/[ ] : The Secondary screen changes every time you touch it.
Basic Operations FUNCTION screen 1 ●● To turn on the screen 1 Touch the display. Press the [FNC] button. List screen hh FUNCTION screen appears. 2 There are some common function keys in the list screens of most sources. 1 Touch to display the FUNCTION screen. 2 The contents of the menu are as follows. • Displays the SETUP Menu screen. • Displays the APP (Apple CarPlay/ Android Auto) screen. • Displays the Screen Adjust screen. • Displays the view camera. • Displays the source selection screen.
Disc Disc Playing a disc ÑÑInsert a disc 1 Insert the disc into the slot. DVD/VCD Basic Operation NOTE • The screen shot below is for DVD. It may be different from the one for VCD. 1 When the operation buttons are not displayed on the screen, touch 4 area. Control screen 1 2 hh The unit loads the disc and playback starts. ÑÑEject a disc 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. Video screen 3 When removing a disc, pull it horizontally.
Disc DVD Disc Menu Operation 2 Operation keys • [E] [F] : Searches for the previous/next content. Touch and hold to fast-forward or fast-backward the disc. • [D/H] : Plays or pauses. •[ ] : Touch to mute or not to mute. 3 Searching area Touch to search for the next/previous content. You can set up some functions using the DVDVIDEO disc menu. 1 Touch 5 area during playback. hh Menu Control screen appears. 2 Perform your desired operation as follows.
USB USB Connecting a USB device 1 Connect the USB device with the USB cable. (P.29) USB Basic Operation Most functions can be controlled from the source control screen and playback screen. Control screen 1 2 3 4 Press the [ Touch [ ] button. ]. Touch [USB]. (P.11) ÑÑDisconnect the USB device 1 2 3 4 Press the [ Touch [ 2 ] button. ]. Touch a source other than [USB]. Detach the USB device. ÑÑUsable USB device You can use a mass-storage-class USB device on this unit.
Tuner Tuner Tuner Basic Operation 3 Operation keys Most functions can be controlled from the source control screen. To enter Tuner source, touch [Tuner] icon in the source selection screen. (P.11) Control screen 1 • [E] [F] : Tunes in a station. The method of frequency switching can be changed (see 2 in table). •[ ] : Touch to mute or not to mute. 4 Preset list • Touch on the right side of the screen to display the Preset list. Touch again to close the list. • Recalls the memorized station.
Tuner SiriusXM® Memory Operation ÑÑAuto memory You can store stations with good reception in memory automatically. 1 Touch desired band key. 2 Touch [ ] on the left side of the screen. Touch [AME]. SiriusXM® SiriusXM® Basic Operation Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio.
SiriusXM® Control screen 3 Artwork / Function panel 1 2 3 5 4 Open the drawer 3 • Displays the album artwork for most SiriusXM music channels. • Touch [ ] of the screen to display the function panel. Touch [ ] to close the panel. –– [Direct Channel]: Touch and enter the desired number. For details, see Instruction Manual. –– [SETUP]: Touch to display the SiriusXM SETUP screen. For details, see Instruction Manual. –– [Replay/Live]: Touch to turn on or off the replay mode. See Instruction Manual.
Bluetooth Control Bluetooth Control ÑÑAbout the cell-phone and Bluetooth audio player 3 Operate your smartphone/cell-phone according to the displayed messages. This unit conforms to the following Bluetooth specifications: ■■ Confirm the request on the smartphone/cell-phone. Version Bluetooth Ver. 4.
Bluetooth Control 8 Touch [Select Device] in the Bluetooth SETUP screen. Using Hands-Free Unit You can use telephone function by connecting the Bluetooth telephone to this unit. NOTE • While Apple CarPlay or Android Auto is being connected, Bluetooth Hands-Free function cannot be used. Only Apple CarPlay or Android Auto Hands-Free function can be used. 9 Touch [ ] you want to connect. ÑÑMake a call 1 Touch [Phone]/[Û]. hh Hands Free screen appears. 2 Select a dialing method.
Bluetooth Control Call using call records Call using the preset number 1 2 1 2 Touch [ ]. Select the phone number from the list. Touch [ ]. Touch the Name or phone number. Call by entering a phone number Call using the phonebook 1 2 Touch [ 1 2 Touch [ 3 Touch [ 3 Select the phone number from the list. ]. Enter a phone number with number keys. ]. ]. Select the person you want to call from the list.
Bluetooth Control ÑÑReceive a call 1 ÑÑOperations during a call Touch [ ] to answer a phone call or [ to reject an incoming call. ] ●● Adjust the receiver volume Press the [−] or [+] button. NOTE • While monitoring the view camera, this screen does not appear even if a call comes in. To display this screen, return the shift knob of car to the driver position. To end call 1 While talking, touch [ ]. ●● Output the dial tone Touch [DTMF] to display the tone input screen.
Controlling Audio Controlling Audio You can adjust the various settings such as audio balance or subwoofer level. 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. ÑÑControlling General Audio 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh Audio screen appears. 3 Touch [Fader / Balance]. 4 Set each item as follows. ■■ [Fader] / [Balance] Adjust the volume balance around the touched area. [C] and [D] adjust the right and left volume balance.
Controlling Audio ÑÑEqualizer Control You can adjust equalizer by selecting the optimized setting for each category. 1 Press the [FNC] button. hh FUNCTION screen appears. 2 Touch [ ]. hh Audio screen appears. 3 Touch [Equalizer]. 4 Touch the screen and set the Graphic Equalizer as desired. ■■ [SW Level] Adjusts the subwoofer volume. ■■ [ALL SRC] Apply the adjusted equalizer to all sources. Touch [ALL SRC] and then touch [OK] on the confirmation screen.
Connection/Installation Connection/Installation Before Installation Before installation of this unit, please note the following precautions. # WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Connection/Installation ÑÑSupplied accessories for Installing the unit installation 1 ÑÑNon-Japanese cars 2 (3 m) x1 x1 3 4 (2 m) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. x1 x1 6 5 (M5 × 6 mm) (M5 × 8 mm) x6 7 x6 8 x1 NOTE • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Connection/Installation ÑÑMicrophone unit ÑÑRemoving the unit 1) Check the installation position of the microphone (accessory 1). 2) Clean the installation surface. 3) Remove the separator of the microphone (accessory 1), and stick the microphone to the place shown below. 4) Wire the microphone cable up to the unit with it secured at several positions using tape or other desired method. 5) Adjust the direction of the microphone (accessory 1) to the driver.
Connection/Installation ÑÑConnecting wires to terminals USB terminal[1] (1.0 m) USB device[2] 5V=1.5A Cap SiriusXM Connect Vehicle Tuner connector Sirius XM For more information on how to install the SiriusXM Connect Vehicle tuner, consult the installation guide included with the tuner. For best safety, be sure to connect the parking sensor. PRK SW Light Green (Parking sensor wire) Accessory 3: Parking Extention cable Connect to the vehicle’s parking brake detection switch harness.
Connection/Installation ÑÑConnecting an iPhone/Android Android smartphone[2] USB cable[2] 1 3 5 7 2 4 6 8 1 3 5 7 2 4 6 8 iPhone[2] Lightning connector Accessory 7 Accessory 8 KS-U62 (0.8m)[3] Speaker impedance: 4-8 Ω White White/Black Gray Gray/Black Green Green/Black Purple Purple/Black To front left speaker USB terminal[1] (1.0 m) 5V=1.5A To front right speaker Cap To rear left speaker To rear right speaker i Phone maximum power supply current : DC 5 V = 1.
Appendix Appendix Specifications ■■Bluetooth section Frequency : 2.402 – 2.480 GHz RF Output Power (E.I.R.P.) : +8 dBm (Avg.), Power Class 1 ■■General About this Unit ■■Copyrights • The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. • Manufactured under license from Dolby Laboratories.
Appendix • THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (¡)ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (¡¡)DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/ OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
Appendix • libogg Copyright (c) 2002, Xiph.org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: –– Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
■■FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Supplier’s Declaration of Conformity Trade Name: JVC Products: MONITOR WITH DVD RECEIVER Model Name: KW-V660BT / KW-V66BT Responsible Party: JVCKENWOOD USA CORPORATION 2201 East Dominguez Street, Long Beach, CA 90810, U.S.A. PHONE: 310 639-9000 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
!B5H-0357-03_QSG_JVC_KWV_K_EnFrEs.