KW-V230BT KW-V235DBT KW-V330BT MONITOR WITH DVD RECEIVER INSTRUCTION MANUAL This instruction manual is used to describe models listed below. Model availability and features (functions) may differ depending on the country and sales area. • Region 2 (DVD Region Code 2 area) • Region 5 (DVD Region Code 5 area) © 2016 JVC KENWOOD Corporation 2017_KW-V_Entry_E.
CONTENTS BEFORE USE............................................................ 2 How to reset your unit.................................................... 3 INITIAL SETTINGS .................................................. 4 Initial setup ......................................................................... 4 Clock settings .................................................................... 4 BASICS ....................................................................
BEFORE USE Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for countries that have adopted separate waste collection systems) Products and batteries with the symbol (crossedout wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you.
INITIAL SETTINGS Initial setup When you power on the unit for the first time or reset the unit, the initial setting screen appears. • You can also change the settings on the screen. (Page 57) Select the viewing angle (Page 59) in relation to the monitor panel to make the panel easier to see. 3 Display the setting screen. 2 Finish the procedure. 1 Perform the initial settings. 4 Display the screen. The Home screen is displayed.
INITIAL SETTINGS 5 Set the clock time. BASICS Component names and functions V Caution on the volume setting: Digital devices produce very little noise compared with other sources. Lower the volume before playing these digital sources to avoid damaging the speakers by sudden increase of the output level. KW-V230BT/KW-V235DBT *1 FM Radio Data System. *2 Synchronizes the clock time with Digital Audio Broadcast. Sets the clock manually.
BASICS KW-V330BT 5 button • Switches the screen. (Press) – The screen switched to depends on the setting. (Page 59) • Turns off the screen. (Hold) (Page 7) • Turns on the screen. (Hold) (Page 7) 6 Volume +/– button Adjusts the audio volume. (Page 7) 7 Monitor panel* 8 Screen (touch panel) * You can change the color of the buttons on the monitor panel. (Page 53) 1 button • Turns on the power. (Press) (See the far right column.) • Turns off the power. (Hold) (See the far right column.
BASICS ❏ Adjusting the volume ❏ Turning off the screen To adjust the volume (00 to 35) KW-V230BT KW-V330BT KW-V235DBT On the monitor panel: KW-V230BT KW-V330BT KW-V235DBT (Hold) Press + to increase, and press − to decrease. • Holding + increases the volume continuously to level 15. KW-V330BT (Hold) On the pop-up short-cut menu (Page 11) (only for KW-V230BT/KW-V235DBT): Display the pop-up short-cut menu by pressing FNC on the monitor panel, then select [Display OFF].
BASICS Common screen operations ❏ Common screen descriptions You can display other screens any time to change the source, show the information, or change the settings, etc. Source control screen Performs source playback operations. • The operation buttons and information displayed vary depending on the selected source. KW-V230BT/KW-V235DBT Common operating buttons: 1 Displays the other operation button window.* 2 Only for KW-V230BT/KW-V235DBT: Displays the screen.
BASICS Common operating buttons: 1 Displays all playback sources and items. (Page 10) 2 Displays the screen. (See the right column.) 3 Displays the setting screen. (Page 4) 4 Displays the phone control screen. (Page 43) 5 Only for KW-V230BT/KW-V235DBT: Displays the source currently played back. 6 Changes the playback source. (Page 11) 7 Only for KW-V330BT: Ejects the disc. (Press) (Page 12) 8 Only for KW-V330BT: Displays the screen.
BASICS Selecting the playback source 1 Display all playback sources and items. On the Home screen: KW-V230BT KW-V330BT KW-V235DBT 2 KW-V230BT/KW-V235DBT KW-V330BT • You can change the icon design on the screen. (Page 53) [DAB]*1 Switches to the digital audio broadcast (DAB). (Page 32) [Tuner] Switches to the radio broadcast. (Page 27) [Disc] Plays a disc. (Page 12) [USB] Plays files on a USB device. (Page 16) [iPod] Plays an iPod/iPhone. (Page 20) [Android™] Plays an Android device.
BASICS ❏ Selecting the playback source on the Home screen Using the pop-up short-cut menu • You can arrange the items to display on the Home screen. (Page 55) While displaying the source control screen, you can jump to another screen from the pop-up short-cut menu. KW-V230BT/KW-V235DBT 1 Display the pop-up short-cut menu.
DISCS Playing a disc KW-V330BT On the Home screen: • If a disc does not have a disc menu, all tracks on it will be played repeatedly until you change the source or eject the disc. • For playable disc types/file types, see page 69. ❏ Playback information on the source control screen For video playback KW-V230BT/KW-V235DBT 1 2 3 4 ❏ Inserting a disc Insert a disc with the label side facing up.
DISCS ❏ Operation buttons on the source control screen For audio playback KW-V230BT/KW-V235DBT 1 2 345 6 7 8 KW-V330BT 13 5 4 2 8 6 7 1 Media type 2 Track/file information • Pressing [H] scrolls the text if not all of the text is shown. 3 Playing time 4 IN indicator 5 Playback status 6 Playback mode (Page 15) 7 File type 8 Current playback item information (folder no./file no./track no.) • To display all available operation buttons, press [ ]/[ ]*1. All the other available buttons are shown.
DISCS ❏ Video menu operations You can display the video control menu during video playback. • The operation buttons disappear when the screen is touched or when no operation is done for about 5 seconds. For video playback except VCD [ MENU] [T MENU] [ ] [ ] [ ] [ ] [ ] [ ] [ [ • Available buttons on the screen and operations differ depending on the type of disc/file being played back. ] ] Displays the disc menu (DVD). Displays the disc menu (DVD). Switches to the direct disc menu mode.
DISCS To select a track directly on a VCD • When playing a VCD with PBC activated, stop playback to deactivate the PBC function, then use the direct selection buttons to select a track number. • The locations of the buttons differ depending on the type of disc/file being played back. – When [ ]/[ ]* is not displayed, display the other operation button window by pressing [ ]/[ ]*.
USB DISCS ❏ Setting items
USB [FNC J]*4 KW-V330BT Playback operations 3 4 2 7 1 When the operation buttons are not displayed on the screen, touch the area shown on the illustration. • To change settings for video playback, see page 52. • The information and available operation buttons on screen differ depending on the type of file being played back.
Android USB ❏ Settings for USB playback— 1 ❏ Selecting a folder/track on the list 1 Display the folder/track list during playback. 2 Select the folder (1), then the item in the selected folder (2). • Repeat the procedure until you select the desired track. 2 wide screen picture on the external monitor. 16:9 (Initial) 4:3 LB 4:3 PS • You can change the page to display more items by pressing [ ]/[ ].
Android ❏ Connecting an Android device Connect an Android device with a cable. • For details about connecting Android devices, see page 65. Compatible Android devices • This unit supports Android OS 4.1 and above. • Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory (AOA) 2.0. • If the Android device supports both mass storage class device and AOA 2.0, this unit always plays back via AOA 2.0 as priority.
iPod/iPhone Android ❏ Selecting a track from the menu 1 Display the audio menu. ❏ Settings for playback on the Android device— 1 ❏ Connecting iPod/iPhone • For details about connecting iPod/iPhone, see page 65. • For playable iPod/iPhone types, see page 70. 2 Select a category (1), then a desired item Connect your iPod/iPhone according to your purpose or the type of iPod/iPhone. (2). • To list the items in alphabetical order, press [ A-Z], then select the first character on the keypad.
iPod/iPhone ❏ Selecting iPod/iPhone device to play and the connection method 4 Select the connection method (1), then confirm the selection ([OK] or [Next]) (2). 1 Display the screen. 5 When selecting [Bluetooth] as the connection method: Select the device (1), then press [OK] to connect (2). On the Home screen: KW-V230BT KW-V330BT KW-V235DBT 2 Display the setting screen.
iPod/iPhone ❏ Displaying/hiding artwork of iPod/ iPhone Playback operations 1 When the operation buttons are not displayed on the screen, touch the area shown on the illustration. • To change settings for video playback, see page 52. ❏ Playback information on the source control screen 1 Artwork (Shown if the song contains artwork) 2 Song/video information • Pressing [H] scrolls the text if not all of the text is shown. 3 Playing time 4 Playback status 5 Playback mode (Page 23) 6 File type 7 Track no.
iPod/iPhone ❏ Operation buttons on the source control screen • To display all available operation buttons, press [ ]/[ ]*1. All the other available buttons are shown. – To hide the window, press [ ]/[ ]*1. Displays the screen. [ ]*2 (Page 49) [FNC J]*3 Displays the pop-up short-cut menu. (Page 11) • To close the menu, press [K]. Displays the audio/video file menu. [ ] (See the right column.) [S] [T] • Selects a track. (Press) • Reverse/forward search. (Hold) Starts/pauses playback.
APPs You can use an App of the connected iPod touch/ iPhone/Android on this unit. • For Apps you can use on this unit, visit . ❏ Playback operations 1 Start the App on your iPod touch/iPhone/ Android. 2 Select “Apps” as the source. (Page 10) Preparation 1 Connect the iPod touch/iPhone/Android. • For Android: Connect the Android device via Bluetooth. (Page 39) • For iPod touch/iPhone: Connect iPod touch/ iPhone with a cable.
Spotify (Only for KW-V230BT Region 2/KW-V235DBT/KW-V330BT Region 2) With Spotify, your music is everywhere. Working out, partying or relaxing, the right music is always at your fingertips. There are millions of songs on Spotify— from old favorites to the latest hits. Just choose the music you love, or let Spotify surprise you. You can stream Spotify from connected iPod touch/iPhone or Android devices.
Spotify 1 Picture data 2 Track information • Pressing [H] scrolls the text if not all of the text is shown. 3 Playing time 4 Playback status 5 Progress bar ❏ Operation buttons on the source control screen • To display all available operation buttons, press [ ]/[ ]*1. All the other available buttons are shown. – To hide the window, press [ ]/[ ]*1. [ ]/[ ] Changes the displayed information each time this button is pressed ( : artist/ : album). Displays the screen.
TUNER Listening to the radio ❏ Playback information on the source control screen KW-V230BT/KW-V235DBT 1 2 3 4 5 6 789 KW-V330BT 2 1 1 Text information • Pressing [H] scrolls the text if not all of the text is shown. • Pressing [Radio Text] switches the information between Radio Text, Radio Text Plus, and PTY code.
TUNER ❏ Tuning in only FM stations with strong signals—Local Seek 2 Presetting stations ❏ Storing stations in the memory 1 Display the screen. You can preset 5 stations for each band. Automatic presetting—SSM (Strong-station Sequential Memory) (for FM only) The unit tunes in only to stations with sufficient signal strength. The LO.S indicator lights up. To deactivate Local Seek: Press [OFF]. (Hold) The local stations with the strongest signals are found and stored automatically.
TUNER Manual presetting ❏ Selecting a preset station KW-V330BT 1 Tune in to a station you want to preset. KW-V230BT/KW-V235DBT 1 Select the band (1), then display the (Page 27) 2 Select a preset number. 1 Select the band (1), then display the preset station window (2). preset station window (2). KW-V230BT/KW-V235DBT (Hold) • You can also select a preset station by pressing [P1] – [P5]. 2 Select a preset station. KW-V330BT • You can also select a preset station by pressing [P1] – [P5].
TUNER FM Radio Data System features ❏ Searching for FM RBDS programs—PTY Search ❏ Activating/deactivating TI/News Standby Reception News Standby Reception 1 Display the screen. TI Standby Reception You can search for your favorite programs being broadcast by selecting the PTY code. 1 2 Select a PTY code. 2 (Hold) • You can change the page to display more items by pressing [ ]/[ ]. PTY Search starts.
TUNER ❏ Tracing the same program—NetworkTracking Reception When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM Radio Data System station of the same network, possibly broadcasting the same program with stronger signals. • When shipped from the factory, Network-Tracking Reception is activated. To change the Network-Tracking Reception setting 1 Display the screen.
DIGITAL RADIO (DAB) (Only for KW-V235DBT) About DAB (Digital Audio Broadcasting) What is DAB system? DAB (Digital Audio Broadcasting) is one of the digital radio broadcasting systems available today. It can deliver digital quality sound without any annoying interference or signal distortion. Furthermore, it can carry text and data. In contrast to FM broadcast, where each program is transmitted on its own frequency, DAB combines several programs (called “services”) to form one “ensemble.
DIGITAL RADIO (DAB) ❏ Selecting a service from the list 1 Display the screen. ❏ Selecting a preset service Presetting services 1 Display the preset services window. ❏ Storing services in the memory You can preset 5 services for each band. 1 Select a service you want to preset. 2 Select a service from the list. (Page 32) 2 Select a preset number. • You can also select a preset service by pressing [P1] – [P5]. 2 Select a preset service.
DIGITAL RADIO (DAB) Radio Data System features ❏ Activating/deactivating TI Standby Reception 2 Select a PTY code. ❏ Searching for Radio Data System programs—PTY Search You can search for your favorite programs being broadcast by selecting the PTY code. 1 (Hold) • You can change the page to display more items by pressing [ ]/[ ]. PTY Search starts. If there is a service broadcasting a program of the same PTY code as you have selected, that service is tuned in.
DIGITAL RADIO (DAB) Settings for Digital Audio Radio You can set the Digital Radio related items. ❏ Setting items • ON (Initial): If the same service is provided by Digital Radio during Radio Data System reception, the unit automatically switches to Digital Radio. If the same service is provided by Radio Data System when reception of the service being provided by Digital Radio becomes poor, the unit automatically switches to Radio Data System. • OFF: Deactivates.
OTHER EXTERNAL COMPONENTS Using the rear view camera To display the picture from the rear view camera manually 4 • To connect a rear view camera, see page 66. • To use a rear view camera, a REVERSE lead connection is required. (Page 64) KW-V230BT KW-V235DBT ❏ Settings for the rear view camera KW-V330BT 1 Display the screen. On the Home screen: KW-V230BT KW-V330BT KW-V235DBT [ON] [OFF] 2 Display the setting screen.
OTHER EXTERNAL COMPONENTS To adjust the picture While the camera screen is displayed... 3 Display the screen. 1 Display the screen. (See the far left column.) 2 Display the parking guidelines adjustment screen. 4 • The video control menu is displayed. (Page 52) To close the picture adjustment menu, touch the same area again.
OTHER EXTERNAL COMPONENTS Using external audio/video players—AV-IN When the operation buttons are not displayed on the screen, touch the area shown on the illustration. • To change settings for video playback, see page 52. ❏ Changing the AV-IN name You can change the AV-IN name displayed on the “AV-IN” source control screen. 1 Display the
BLUETOOTH Information for using Bluetooth® devices Bluetooth is a short-range wireless radio communication technology for mobile devices such as mobile phones, portable PCs, and other devices. Bluetooth devices can be connected without cables and communicate with each other. Notes • While driving, do not perform complicated operations such as dialing numbers, using the phone book, etc. When you perform these operations, stop your car in a safe place.
BLUETOOTH Pairing a Bluetooth device using a PIN code (for Bluetooth 2.0) 1 Display the screen. On the Home screen: KW-V230BT KW-V330BT KW-V235DBT 4 Change the PIN code. • If you wish to skip changing the PIN code, go to step 3. • The PIN code is initially set to “0000”. • The maximum number of digits in the PIN code is 15. 6 Select the unit (“JVC KW-V”) on your Bluetooth device. • If a PIN code is required, enter “0000” (initial).
BLUETOOTH ❏ Connecting/disconnecting a registered Bluetooth device Two devices can be connected simultaneously. 4 Select [ON] (to connect) or [OFF] (to disconnect) for the target (1), then display the screen (2). 1 Display the screen. • When a Bluetooth mobile phone is connected, the signal strength and battery level are displayed when the information is acquired from the device.
BLUETOOTH Using a Bluetooth mobile phone ❏ Receiving a call ❏ Ending a call While talking... ❏ Switching between handsfree mode and phone mode While talking... When a call comes in... • Call information is displayed if acquired. • Phone operation is not available while the picture from the rear view camera is displayed. (Page 36) ❏ Adjusting the volume of calls/earpiece/ microphone While talking...
BLUETOOTH ❏ Sending text during a call You can send text during a call using the DTMF (Dual Tone Multi Frequency) function. While talking... ❏ Switching between two connected devices You can change the device to use in the following situations: • When 2 devices are connected • While in phone control screen 2 Select a method to make a call. 1 2 3 4 5 • The active device is highlighted. ❏ Making a call 1 Display the phone control screen.
BLUETOOTH From the call history/phone book/preset list • To use the A to Z search in the phone book: 1 1 • To display other phone numbers: When the phone book list is displayed, you can switch between phone numbers if several phone numbers are registered for the same contact (up to 10 phone numbers per contact). 1 Switch the phone number. [ [ [ ] ] ] From the call history (missed calls/ received calls/dialed calls) From the phone book 2 Select the initial.
BLUETOOTH Direct number entry You can enter up to 31 numbers. Voice dialing • Available only when the connected mobile phone has a voice recognition system. 1 Activate voice dialing. On the phone control screen: • Press [ ] to delete the last entry. • Press and hold [0/+] to add “+” to the phone number. ❏ Presetting phone numbers You can preset up to 5 phone numbers. 1 Display the phone control screen. (Page 43) 2 Select phone book or call history. 3 Select a phone number to preset.
BLUETOOTH Using the Bluetooth audio player • To register a new device, see page 39. • To connect/disconnect a device, see page 41. • When “BT Audio” is selected as the source, you can connect to five Bluetooth audio devices and switch between these five devices. ❏ Playback information on the source control screen • The operation buttons, indications and information displayed on the screen differ depending on the connected device.
BLUETOOTH Settings for Bluetooth devices 4 Configure the Bluetooth settings. You can change various settings for using Bluetooth devices on the screen. 1 Display the screen. On the Home screen: KW-V230BT KW-V330BT KW-V235DBT ❏ Setting items 2 Display the setting screen. 3 Display the screen.
SETTINGS Settings for using applications of iPod touch/iPhone/Android 3 Display the screen. Before using applications of iPod touch /iPhone/ Android, select the device to use. When connecting the device for the first time, the setup screen (for connection, etc.) appears. Follow the procedure on the setup screen to configure the settings. Preparation: • For Android: Connect the Android device via Bluetooth.
SETTINGS Sound adjustment ❏ Using the sound equalization • The adjustments are memorized for each source until you adjust the sound again. If the source is a disc, the adjustments are stored for each of the following categories. – DVD/VCD – CD – DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC/ FLAC • You cannot adjust the sound when the unit is in standby. Selecting a preset sound mode 1 Display the screen.
SETTINGS ❏ Setting the speakers—car type, speaker size and crossover frequency Preparation: Select the appropriate crossover network mode beforehand. (Page 49) 4 Select the speaker type (1), select the size of the selected speaker (2), then display the screen (3). 1 Display the screen. On the Home screen: KW-V230BT KW-V330BT KW-V235DBT 2 Display the screen. • When a speaker is not connected, select .
SETTINGS ❏ Adjusting the Digital Time Alignment (DTA) 4 Select an item to make an adjustment. Make fine adjustments to the delay time of the speaker output to create a more suitable environment for your vehicle. 1 Display the screen. On the Home screen: KW-V230BT KW-V330BT KW-V235DBT [Distance] [Gain] 2 Display the
SETTINGS Adjustment for video playback ❏ Adjusting the picture You can adjust the picture quality. 1 Display the picture adjustment screen. On the source control screen: Adjusts the brightness. (−15 to +15) Adjusts the contrast. (−10 to +10) Adjusts the blackness. (−10 to +10) Adjusts the color. (−10 to +10) Adjusts the tint. (−10 to +10) Adjusts the sharpness.
SETTINGS ❏ Zooming the picture You can zoom the picture (, to ). • When < > is set to or (Page 52), the picture is zoomed with the aspect ratio of the setting. 1 Display the magnification level selecting Changing the display design You can change the background and panel color. 1 Display the screen. On the Home screen: KW-V230BT KW-V330BT KW-V235DBT 4 Select an item to change, then select the design or color.
SETTINGS Only for KW-V330BT: To change the panel color Display the panel color selection screen (1), select the dimmer setting ([ ]: dimmer on or [ ]: dimmer off) (2), then select the panel color (3). KW-V330BT Display the background design selection screen (1), select the dimmer setting ([ ]: dimmer on or [ ]: dimmer off) (2), then select the background design (3). *1 • You can also adjust the color yourself.
SETTINGS Customizing the Home screen You can arrange the items to display on the Home screen. KW-V230BT/KW-V235DBT 4 Select an item to replace (1), then select the item you want to display in the selected position (2). KW-V330BT 1 Select an item to replace. On the Home screen: Press and hold the icon you want to replace. 1 Display the screen. On the Home screen: (Hold) 2 Display the setting screen. Repeat this step to place icons for other items.
SETTINGS Customizing the system settings ❏ Updating the system 4 You can update the system by connecting a USB device containing an update file. • To update the system, visit . ❏ Memorizing/recalling the settings • You can memorize the settings changed in the menu and recall the memorized settings any time. • The memorized settings are kept even when the unit is reset. 1 Display the screen.
SETTINGS ❏ Adjusting the touch position 5 You can adjust the touch position on the touch panel if the position touched and the operation performed do not match. 1 Display the setting screen. (Page 56) 2 Display the screen. * Updates the system application. Updates the system. Updates the DVD system application. Updates the Digital Radio (DAB) module application.
SETTINGS ❏
SETTINGS ❏ setting screen • Auto (Initial): Dims the screen and button illumination when you turn on the headlights. • ON: Activates dimmer. • OFF: Cancels. Change the display design. (Page 53) • ON: Displays the clock while a video source is playing. • OFF (Initial): Cancels. • ON (Initial): Activates the demonstration on the screen. • OFF: Cancels. • ON: Scrolls the displayed information repeatedly.
SETTINGS ❏ setting screen * Select the text language used for on-screen information. • English (Initial for KW-V230BT Region 2/ KW-V235DBT/KW-V330BT)/Español/Français/ Deutsch/Italiano/Nederlands/Português/ Türkçe/Руccĸий (Initial for KW-V230BT Region 5)/ / / / / / / Bahasa Malaysia/Bahasa Indonesia – For external monitors, only English/Spanish/ French/German/Italian/Dutch/Russian/ Portuguese are available.
REMOTE CONTROLLER (Only for KW-V230BT Region 2/KW-V235DBT/KW-V330BT) To use the remote controller, purchase RM-RK258 separately. Preparation ❏ Removing the battery sheet Pull the battery sheet out from the remote controller to activate the battery. ❏ Changing the battery of the remote controller CR2025 (+side) You can also operate this unit from Smartphone using JVC Remote APP. For details, visit . • Use a commercially available button battery (CR2025).
REMOTE CONTROLLER Operations using the remote controller (RM-RK258) 1–5 ANGLE ❏ Basic button functions ATT DISP FM/J / AM/K / VOL +/ VOL – SRC I/W Attenuates/restores the sound. Switches the screen between the current source and the App screen from the connected iPod touch/iPhone/Android. • Selects the band. • Selects a title/item/folder. • Searches for stations automatically.* • Searches for stations manually.* (Hold) • Selects a track. Adjusts the volume level. Selects the source.
CONNECTION/INSTALLATION Before installing the unit V WARNING • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse.
CONNECTION/INSTALLATION Connection ❏ Connecting wires to terminals USB terminal (1.0 m): See page 65.*1 See page 66. 10 A fuse *2 Connect the aerial cord to the aerial terminal.*3 Connect to the vehicle’s reverse lamp harness when using the Purple with white stripe optional rear view camera. (Reverse sensor wire) See page 66. 1 Light green (Parking sensor wire) To the OE remote adapter (not supplied) which is compatible with your car.
CONNECTION/INSTALLATION ❏ Connecting a USB device ❏ Connecting an Android device USB device (commercially available) Android device (commercially available) ❏ Connecting iPod/iPhone iPod/iPhone (Lightning connector models) (commercially available) iPod/iPhone (30-pin connector models) (commercially available) KS-U62 (optional accessory) 1.0 m KW-V230BT KW-V235DBT (Front panel) USB 2.0 cable (commercially available) 0.8 m 30-pin to USB cable (accessory of iPod/ iPhone) 0.8 m 1.
CONNECTION/INSTALLATION ❏ Connecting external components Connecting external amplifiers for 3 way speakers system ❏ Connecting microphone for Bluetooth Connect the microphone (5) to the MIC terminal. • To install the microphone, peel off the adhesive tape, fix on the installation position, then adjust the direction of the microphone to face the driver. After installing, fix the microphone cable to the car with clamps (commercially available).
CONNECTION/INSTALLATION Installing/removing the unit ❏ Installing the unit ❏ Removing the trim plate ❏ Removing the unit 1 Engage the catch pins on the extraction 1 Remove the trim plate. (See the left key (4) and remove the two locks on the lower part. Lower the frame and pull it forward. column.) 2 Insert the two extraction keys (4), then pull them as illustrated so that the unit can be removed.
REFERENCES Maintenance ❏ Caution on cleaning the unit Do not use any solvent (for example, thinner, benzine, etc.), detergent, or insecticide. This may damage the monitor or the unit. ❏ To keep discs clean Dirty discs may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from the center to the edge. Recommended cleaning method: Gently wipe the panel with a soft, dry cloth.
REFERENCES Playing audio files (MP3/WMA/WAV/AAC/FLAC) • This unit can play back files with the extension code: – For disc: <.mp3>, <.wma>, <.wav>, <.m4a> – For USB mass storage class device: <.mp3>, <.wma>, <.wav>, <.aac>, <.m4a>, <.flac> • This unit can play back files that meet the conditions below: – Bit rate: MP3: 8 kbps – 320 kbps WMA : For disc: 5 kbps – 320 kbps For USB : 32 kbps – 192 kbps AAC: 16 kbps – 320 kbps – Sampling frequency: MP3/WMA: 8 kHz – 48 kHz WAV: 44.
REFERENCES Playing Recordable/Rewritable discs • This unit can recognize a total of 5 000 files and 250 folders (a maximum of 999 files per folder). • Use only “finalized” discs. • This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing. • Some discs or files may not be played back due to their characteristics or recording conditions.
REFERENCES • When operating an iPod/iPhone, some operations may not be performed correctly or as intended. In this case, visit the following JVC web site: • For some iPod/iPhone models, the performance may be abnormal or unstable during operation. In this case, disconnect the iPod/iPhone device, then check its condition. If the performance is not improved or slow, reset your iPod/iPhone. • When you turn on this unit, the iPod/iPhone is charged through the unit.
REFERENCES Error message list If an error occurs while using the unit, a message appears. Take appropriate action according to the following message/remedy/cause list. “No Signal”/“No Video Signal”: • Start playback on the external component connected to the iPod/AV-IN input terminal. • Check the cords and connections. • Signal input is too weak. “Miswiring DC Offset Error”/“Warning DC Offset Error”: • A speaker cord has shorted or it has come into contact with the car chassis.
REFERENCES ❏ Discs ❏ USB ❏ Android Recordable/Rewritable discs cannot be played back. • Insert a finalized disc. • Finalize the discs with the component which you used for recording. “Reading” does not disappear from the screen. • Turn the power off and on again. Sound cannot be heard during playback. • Reconnect the Android device. • When is set to [AUDIO MODE], launch any media player application on the Android device and start playback.
REFERENCES ❏ iPod/iPhone ❏ Tuner ❏ Bluetooth No sound comes out of the speakers. • Disconnect the iPod/iPhone, then connect it again. • Select another source, then reselect “iPod”. SSM automatic presetting does not work. • Store stations manually. (Page 29) Phone sound quality is poor. • Reduce the distance between the unit and the Bluetooth mobile phone. • Move the car to a place where you can get a better signal reception. The iPod/iPhone does not turn on or does not work.
REFERENCES The connected audio player cannot be controlled. • Check whether the connected audio player supports AVRCP (Audio Video Remote Control Profile). The Bluetooth device does not detect the unit. • Search from the Bluetooth device again. The unit does not pair with the Bluetooth device. • For devices compatible with Bluetooth 2.1: Register the device using a PIN code. (Page 40) • For devices compatible with Bluetooth 2.0: Enter the same PIN code for both the unit and target device.
REFERENCES ❏ USB interface section ❏ Bluetooth section ❏ DSP section USB Standard USB 2.0 Full Speed/High Speed Compatible Device Mass Storage Class Technology Frequency Output Power Equalizer 13 Band Band Frequency (Hz) (BAND1-13): 62.5/100/160/250/400/630/1k/ 1.6k/2.5k/4k/6.3k/10k/16k Level: −09 to +09 (−9 dB to +9 dB) Q: 1.35/1.5/2.0 File System FAT 16/32 Maximum Power Supply Current DC 5 V 1.5 A Bluetooth 3.0 2.402 GHz to 2.
REFERENCES ❏ FM tuner section ❏ LW tuner section ❏ Audio section Frequency Range 50 kHz: 87.5 MHz to 108.0 MHz 30 kHz*: 65.0 MHz to 74.0 MHz Frequency Range (9 kHz) 153 kHz to 279 kHz Maximum Power (Front & Rear) 50 W × 4 Usable Sensitivity 45 μV Full Bandwidth Power (Front & Rear) 22 W × 4 (at less than 1%THD) ❏ MW tuner section Preout Level 4 V/10 kΩ Preout Impedance ≤ 600 Ω Speaker Impedance 4 Ω to 8 Ω Usable Sensitivity 50 kHz (S/N: 30 dB, 22.5 kHz): 6.2 dBf (0.
REFERENCES ❏ Trademarks and licenses • Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby Laboratories. • “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other countries. • The “AAC” logo is a trademark of Dolby Laboratories. • Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Declaration of Conformity with regard to the RE Directive 2014/53/EU Declaration of Conformity with regard to the RoHS Directive 2011/65/EU Manufacturer: JVC KENWOOD Corporation 3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan EU Representative: JVC Technical Services Europe GmbH Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany English Italiano Český Slovensko Hereby, JVCKENWOOD declares that the radio equipment “KW-V230BT/ KW-V235DBT/KW-V330BT” is in compliance with Directi
Eesti ROMÂNĂ Українська Käesolevaga JVCKENWOOD kinnitab, et „KW-V230BT/KW-V235DBT/KW-V330BT“ raadiovarustus on vastavuses direktiiviga 2014/53/EL. ELi vastavusdeklaratsiooni terviktekst on kättesaadav järgmisel internetiaadressil: http://www.jvc.net/cs/car/eudoc/ Prin prezenta, JVCKENWOOD declară că echipamentul radio “KW-V230BT/ KW-V235DBT/KW-V330BT” este în conformitate cu Directiva 2014/53/UE.