ENGLISH FRANÇAIS ESPAÑOL KW-R940BTS KW-X840BTS CD RECEIVER DIGITAL MEDIA RECEIVER INSTRUCTION MANUAL INSTRUCTION MANUAL RÉCEPTEUR CD RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE MANUEL D’INSTRUCTIONS MANUEL D’INSTRUCTIONS RECEPTOR CON CD RECEPTOR DE MEDIOS DIGITALES MANUAL DE INSTRUCCIONES MANUAL DE INSTRUCCIONES For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No.
KW-R940BTS: CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Important Notice concerning the Software -jansson Copyright (c) 2009-2012 Petri Lehtinen
sha2 AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/ Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved. Author: Chris G. Demetriou Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved.
T-Kernel 2.0 This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum (www.tron.org) BSD-3-Clause Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved. You may obtain a copy of the license at https://opensource.org/licenses/BSD-3-Clause THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
Contents Before Use ................................................................................................. 3 References .............................................................................................. 36 Basics ......................................................................................................... 4 Maintenance Getting Started ........................................................................................
Before Use IMPORTANT • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings and Cautions in this manual. • Please keep the manual in a safe and accessible place for future reference. WARNING • Do not operate any function that takes your attention away from safe driving. • Do not ingest the battery, Chemical Burn Hazard. The remote control supplied with this product contains a coin/button cell battery.
Basics Faceplate KW-R940BTS: Loading slot KW-X840BTS: Display window* Volume knob How to reset * Only for illustration purpose. To On the faceplate Turn on the power Press SOURCE B. • Press and hold to turn off the power. Adjust the volume Turn the volume knob. Press the volume knob to mute the sound or pause playback. • Press again to cancel. The volume level returns to the previous level before muting or pause. Select a source • Press SOURCE B repeatedly.
Getting Started Basics Remote control (RM-RK52) This unit can be remotely controlled with an optionally purchased remote control. Remote sensor (Do not expose to bright sunlight.) Pull out the insulation sheet when using for the first time. How to replace the battery 1 Cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], see page 6), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB” 1 Press the volume knob.
Getting Started To set the date 7 Turn the volume knob to select [DATE SET], then press the knob. 8 Turn the volume knob to make the settings, then press the knob. Set the date in the order of “Day” “Month” “Year”. 9 Press MENU to exit. To return to the previous setting item, press 3 [UPDATE SYSTEM] [F/W UP xxxx] . [FACTORY RESET] Set the basic settings MENU. 1 Press and hold 2 Turn the volume knob to select an item (see the following table), then press the knob.
Radio Settings in memory You can store up to 18 stations for FM and 6 stations for AM. Store a station While listening to a station... Press and hold one of the number buttons (1 to 6). (or) 1 Press and hold the volume knob until “PRESET MODE” flashes. 2 Turn the volume knob to select a preset number, then press the knob. “MEMORY” appears once the station is stored. “STEREO” indicator lights up when receiving an FM stereo broadcast with sufficient signal strength.
Radio Default: [XX] [AREA] [N.AMERICA]: For North/Central/South America, AM/FM intervals: 10 kHz/200 kHz. ; [S.AMERICA]: For some South American countries, AM/FM intervals: 10 kHz/50 kHz. ; [EUROPE]: For any other areas, AM/FM intervals: 9 kHz/50 kHz. [PTY SEARCH]*3 Select a PTY code (see the following “PTY code”). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.
CD/USB/iPod Insert a disc (for KW-R940BTS) Connect an iPod/iPhone Label side Eject disc iPod/ iPhone USB input terminal Accessory of the iPod/iPhone* The source changes to CD automatically and playback starts. The source changes to iPod USB automatically and playback starts. • You can also connect iPod/iPhone via Bluetooth. (Page 20) Connect a USB device * Do not leave the cable inside the car when not in use. USB input terminal USB device Basic operations USB 2.
CD/USB/iPod To On the faceplate On the remote control Reverse/ Fast-forward Press and hold S / T. Press and hold H / I. Select a track/file Press S / T. Press H / I. Select a folder*1 Press 1 J / 2 K. Press J / K. Repeat play*2 Press 5 B repeatedly. [TRACK REPEAT]/[ALL REPEAT]: Audio CD [TRACK REPEAT]/[FOLDER REPEAT]/[ALL REPEAT]: MP3/WMA/AAC/WAV/FLAC file [REPEAT ONE]/[REPEAT ALL]/[REPEAT OFF]: iPod Random play*2 While in USB source, press 6 MODE repeatedly.
AUX CD/USB/iPod Quick search (applicable only for CD source and USB source) If you have many files, you can search through them quickly. 1 2 3 4 Press . Turn the volume knob to select a folder/list, then press the knob. Turn the volume knob quickly to browse through the list quickly. Turn the volume knob to select a file, then press the knob. Selected file starts playing. You can listen to music from a portable audio player via the auxiliary input jack.
Pandora® You can listen to Pandora on iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth). Preparation: • Install the latest version of the Pandora application on your device (iPhone/ iPod touch or Android device), then create an account and log in to Pandora. • Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. (Page 6) To On the faceplate On the remote control Play back/pause Press the volume knob. Press d. Skip a track Press T. Press I.
Pandora® Bookmark current song information Press and hold the volume knob. “BOOKMARKED” appears and the information is stored to your device. • The bookmark is available on your Pandora account but not on this unit. Spotify You can listen to Spotify on iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth).
Spotify To On the faceplate Play back/pause Press the volume knob. Press d. Skip a track Press S*1 / T. Press H*1 / I. Select thumbs up or thumbs down *2 Press 1 J / 2 K. Start radio Press and hold 6. Repeat play*3 Press 5 B repeatedly. [ALL REPEAT], [ONE REPEAT]*1, [REPEAT OFF] Random play*3 Press 4 A repeatedly *1. [ALL RANDOM], [RANDOM OFF] On the remote control Press J / K. ( Not available ) ( Not available ) Search for a song or station .
SiriusXM® Radio Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit . Preparation: 1 Connect the optional SiriusXM Vehicle Tuner (commercially available).
SiriusXM® Radio Select a stored channel SmartFavorites and TuneStart™ Press one of the number buttons (1 to 6) (or press J / K on the remote control). (or) 1 Press . 2 Turn the volume knob to select PRESET, then press the knob. 3 Turn the volume knob to select a preset number, then press the knob. User preset channels are initially assigned as the SmartFavorites channels. SmartFavorite channel is available with SXV200 or later SiriusXM tuner models.
SiriusXM® Radio To On the faceplate Select a stored SmartFavorite channel Press one of the number buttons (1 to 6). 1 Press . 2 Turn the volume knob to select PRESET, then press the knob. 3 Turn the volume knob to select a preset number, then press the knob. Cancel SmartFavorites channels 1 Press . 2 Turn the volume knob to select PRESET, then press the knob. 3 Turn the volume knob to select a preset number, then press and hold the knob. “ ” is removed from the last character.
Using Other Applications SiriusXM® Radio [CODE SET] 1 2 3 4 5 6 • Press the volume knob to enter [NEW CODE]. Turn the volume knob to select a number. Press S / T to move to the entry position. Repeat step 2 and step 3 to enter a new 4-digit pass code. Press the volume knob to confirm. Repeat step 2 to step 5 to reconfirm the pass code. Make a note of the new pass code to enter channel lock settings for next time. [LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting.
Bluetooth® Using Other Applications Default: [XX] [REMOTE APP] [SELECT] [IOS] [ANDROID] Selects the device ([IOS] or [ANDROID]) to use the application. [YES]: Selects iPhone/iPod touch to use the application via Bluetooth or connected via USB input terminal. ; [NO]: Cancels. If [IOS] is selected, select iPod BT source (or iPod USB source if your iPhone/ iPod touch is connected via USB input terminal) to activate the application.
Bluetooth® Pair and connect a Bluetooth device for the first time 1 Press SOURCE B to turn on the unit. 2 Search and select the name of your receiver (“KW-R940BTS”/ “KW-X840BTS”) on the Bluetooth device. “BT PAIRING” flashes on the display. • For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching. 3 Perform (A) or (B) depending on what appears on the display.
Bluetooth® Bluetooth — Mobile phone The following operations may differ or be unavailable depending on the connected phone. To On the faceplate On the remote control Answer a call Press or the volume knob. Press J / K / H / I. Reject a call Press and hold or the volume knob. Press and hold J / K / H / I. End a call Press and hold or the volume knob. Press and hold J / K / H / I. First incoming call... While talking on the first incoming call...
Bluetooth® *1 This adjustment will not affect the volume of the other sources. *2 Press and hold VOL + to continuously increase the volume to 15. *3 Operations may vary according to the connected Bluetooth device. Default: [XX] [SETTINGS] [AUTO ANSWER] [01 SEC] to [30 SEC]: Answers an incoming call automatically in the selected time (in seconds). ; [OFF]: Cancels. Improve the voice quality [RING COLOR] While talking on the phone... 1 Press and hold MENU.
Bluetooth® [PHONEBOOK] (Applicable only if the phone supports PBAP.) 1 Press 1 J / 2 K to select the desired letter (A to Z, 0 to 9, and OTHERS). • “OTHERS” appears if the first character is other than A to Z, 0 to 9. 2 Turn the volume knob to select a name, then press the knob. 3 Turn the volume knob to select a phone number, then press the knob to call. • For using phonebook with this unit, make sure to allow access to or transfer from your smartphone.
Bluetooth® Default: [XX] [BT MODE] [PHONE SELECT] [AUDIO SELECT] Selects the phone or audio device to connect or disconnect. “ ” appears in front of the device name when connected. “ ” appears in front of the current playback audio device. • You can connect a maximum of two Bluetooth phones and one Bluetooth audio device at a time. [DEVICE DELETE] 1 Turn the volume knob to select a device to delete, then press the knob. 2 Turn the volume knob to select [YES] or [NO], then press the knob.
Bluetooth® The connectivity result flashes on the display. “PAIRING OK” and/or “HANDS-FREE OK”*1 and/or “AUD.STREAM OK”*2 and/ or “PBAP OK”*3: Compatible Bluetooth — Audio *1 Compatible with Hands-Free Profile (HFP) *2 Compatible with Advanced Audio Distribution Profile (A2DP) *3 Compatible with Phonebook Access profile (PBAP) After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has been deleted, and the unit exits check mode.
AMAZON ALEXA Bluetooth® To On the faceplate Repeat play Press 5 B repeatedly. [TRACK REPEAT], [ALL REPEAT], [GROUP REPEAT]*1, [REPEAT OFF] Random play On the remote control ( Not available ) Press 4 A repeatedly. [GROUP RANDOM]*1, [ALL RANDOM], [RANDOM OFF] Select a file from a folder/list Refer to “Select a file to play” on page 10. Switch between connected Bluetooth audio devices Press 6.*2 ( Not available ) Preparation: • Create an account at .
AMAZON ALEXA Option B: Manual Pairing 1 Start up the Alexa mobile application and go to the “Devices” tab. 2 Tap the “ + “ icon at the top right corner. 3 Tap “Add Device”. 4 Tap “Automotive Accessory” or “Headphones” from the list of device types. 5 Tap the name of your receiver (“KW-R940BTS”/“KW-X840BTS”) and follow the instructions. Once the setup process is completed, the Alexa mobile application will establish a connection with this unit.
Audio Settings AMAZON ALEXA Start listening While in Alexa idle state... 1 Press on the unit to activate Alexa. The display shows: “LISTENING...”. 2 Communicate with Alexa via the connected microphone. (Page 19) 3 During music playback in ALEXA source, you can perform the following operations: To On the faceplate On the remote control Play back/pause Press the volume knob. Press d. Reverse skip/ Forward skip Press S / T. Press H / I. to pause the music and activate Alexa.
Audio Settings Other settings [PRO EQ] MENU. 1 Press and hold 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. 4 Press MENU to exit. To return to the previous setting item, press Default: [XX] [EASY EQ] [62.5HZ] [LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source.
Audio Settings [FADER] (Not applicable when 3-way crossover is selected.) [POSITION R15] to [POSITION F15] ([POSITION 00]): Adjusts the front and rear speaker output balance. [BALANCE]*3 [POSITION L15] to [POSITION R15] ([POSITION 00]): Adjusts the left and right speaker output balance. [VOLUME ADJUST] [LEVEL –15] to [LEVEL +06] ([LEVEL 00]): Presets the initial volume level of each source by comparing to the FM volume levels. (Before adjustment, select the source you want to adjust.
Audio Settings Speaker output settings [SPK/PRE OUT] Crossover settings (Applicable only if [X ' OVER TYPE ] is set to [2-WAY]) (page 30) Select the output setting for the speakers [SPK/PRE OUT], based on the speaker connection method. Connection via lineout terminals Audio signal through lineout terminal FRONT REAR SW [REAR/REAR] (default) Front speakers output Rear speakers output [SUB.W/SUB.
Audio Settings 2-way crossover setting items [SUBWOOFER LPF]*2 [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/ [90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/ [220HZ]/[250HZ]/[THROUGH] [3.5"]/[4"]/[4.75"]/[5"]/[6.5"]/[6.75"]/[7"]/ [4×6]/[5×7]/[6×8]/[6×9]/[7×10] [SW LPF SLOPE] [–06DB]/[–12DB]/[–18DB]/[–24DB] [SMALL]/[MIDDLE]/[LARGE]/[NONE] (not connected) [SW LPF GAIN] [SPEAKER SIZE] [FRONT] [SIZE] [TWEETER] [REAR]*1 [3.5"]/[4"]/[4.75"]/[5"]/[6.5"]/[6.
Audio Settings [MID RANGE] [HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/ [100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]/ [THROUGH] [HPF SLOPE] [–06DB]/[–12DB] [LPF FRQ] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.3KHZ]/ [8KHZ]/[10KHZ]/[12.5KHZ]/[THROUGH] [LPF SLOPE] [–06DB]/[–12DB] Digital Time Alignment settings Digital Time Alignment sets the delay time of the speaker output to create a more suitable environment for your vehicle.
Display Settings Audio Settings Determining the delay time automatically If you specify the distance from the currently set listening position to every speaker, the delay time will be automatically calculated. 1 Set [POSITION] and determine the listening position as the reference point (the reference point for [FRONT ALL] will be the center between the right and left in the front seats). 2 Measure the distances from the reference point to the speakers.
Display Settings 1 Press and hold MENU. 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. MENU to exit. 4 Press To return to the previous setting item, press . Default: [XX] [DISPLAY] [DIMMER] Dims the illumination. [OFF]: Dimmer is turned off. Brightness changes to [DAY] setting. [ON]: Dimmer is turned on. Brightness changes to [NIGHT] setting.
Display Settings Maintenance [COLOR] [PRESET] [DAY COLOR] [NIGHT COLOR] [COLOR GUIDE] Selects illumination colors for the buttons on different zones separately. 1 Select a zone ([ZONE 1], [ZONE 2], [ALL ZONE]). (See the illustration on page 34.) 2 Select a color for the selected zone. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown. • [COLOR FLOW01] to [COLOR FLOW03]: Color changes at different speeds.
References Playable files • Playable audio file: For disc: KW-R940BTS: MP3 (.mp3), WMA (.wma), AAC (.aac) For USB mass storage class device: MP3 (.mp3), WMA (.wma), AAC (.aac), AAC (.m4a), WAV (.wav), FLAC (.
References Change the display information Source name Display information: Main (Supplementary) For MP3/WMA/AAC/WAV/FLAC files: Song title (Artist) Song title (Artist) with Music Synchronization Effect*2 Song title (Album title) Song title (Date) File name (Folder name) File name (Date) Playing time (Date) back to the beginning Each time you press MENU, the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO NAME”, or other information (eg.
Troubleshooting General Sound cannot be heard. “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “PROTECTING SEND SERVICE” appears. Send the unit to the nearest service center. Source cannot be selected. Check the [SOURCE SELECT] setting. (Page 6) The unit does not work at all. Reset the unit. (Page 4) Radio Correct characters are not displayed.
Troubleshooting 40 Remedy “LOADING” appears when you enter search mode by pressing . This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later. “NO DISC” Insert a playable disc into the loading slot. “NO DEVICE” Connect a device (USB/iPod/iPhone), and change the source to USB/iPod/iPhone again. “MEMORY FULL” You have reached the maximum storage limit of your iPod/iPhone. “ADD ERROR” New station creation is unsuccessful.
Troubleshooting Your subscription is updated. Press the volume knob to continue. “CODE ERROR” Make sure you have entered the correct pass code. (Page 17) “NO CONTENT” There is insufficient content to start TuneScan. “SCAN CANCEL” Bluetooth® Remedy “SUBSCRIPTION UPDATED – PRESS ENTER TO CONTINUE.” • Search from the Bluetooth device again. • Reset the unit. (Page 4) Bluetooth pairing cannot be made. • Make sure you have entered the same PIN code to both the unit and Bluetooth device.
Installation/Connection Troubleshooting AMAZON ALEXA Symptom Remedy No response from Alexa after the voice input. Amazon cloud was unable to analyze the voice input. Wrong response from Alexa. Alexa misunderstood what was said or did not catch the entire request or sentence spoken. Please try again. (Page 27, 28) “DISCONNECTED” Be sure to connect your smartphone to the unit via Bluetooth. (Page 19) Not able to connect or reconnect to Alexa mobile application.
Installation/Connection Part list for installation (A) Wiring harness (×1) Installing the unit (in-dash mounting) Install onto the car brackets using the supplied screws (B) or (C). The screw holes differ depending on the model of the cars. Do the required wiring. (Page 44) (B) Flat head screw, M5 × 8 mm (M5 × 3/8”) (×8) Car bracket* (C) Round head screw, M5 × 8 mm (M5 × 3/8”) (×8) Basic procedure 1 Remove the key from the ignition switch, then disconnect the terminal of the car battery.
Installation/Connection Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Antenna terminal Vehicle dashboard Fuse (10 A) Light blue/yellow Factory wiring harness (vehicle) To the steering wheel remote control adapter Custom wiring harness (separately purchased) Join the same color wires together.
Installation/Connection Connect external components Connect external amplifiers via output terminals Signal cord (not supplied) JVC Amplifier* Output terminals Remote wire (not supplied) To remote lead (blue/white) of the wiring harness. (Page 44) No Part 1 For KW-X840BTS: MIC (Microphone input terminal) (page 19) 2 Output terminals (See the following “Connect external amplifiers via output terminals”.) 3 For KW-X840BTS: Expansion port (12 V available).
Specifications 87.9 MHz — 107.9 MHz (200 kHz step) 87.5 MHz — 108.0 MHz (50 kHz step) Usable Sensitivity (S/N = 26 dB) 8.2 dBf (0.71 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.0 μV/75 Ω) Frequency Response (±3 dB) 30 Hz — 15 kHz Signal-to-Noise Ratio (MONO) 64 dB Stereo Separation (1 kHz) 40 dB AM Frequency Range Usable Sensitivity (S/N = 20 dB) 530 kHz — 1 700 kHz (10 kHz step) 531 kHz — 1 611 kHz (9 kHz step) USB Tuner FM Frequency Range 29 dBμ (28.
Audio Version Bluetooth V4.2 Operating Voltage 12 V DC car battery Frequency Range 2.402 GHz — 2.480 GHz Installation Size (W × H × D) KW-R940BTS: 178 mm × 100 mm × 156 mm (7-1/16" × 3-15/16" × 6-3/16") RF Output Power (E.I.R.P.) +4 dBm (MAX), Power Class 2 Maximum Communication Range Line of sight approx. 10 m (32.8 ft) Pairing SSP (Secure Simple Pairing) Profile HFP1.7.1 (Hands-Free Profile) A2DP (Advanced Audio Distribution Profile) AVRCP1.6.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
ENGLISH FRANÇAIS ESPAÑOL CD RECEIVER RÉCEPTEUR CD RECEPTOR CON CD KW-R940BTS DIGITAL MEDIA RECEIVER RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE RECEPTOR DE MEDIOS DIGITALES KW-X840BTS For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website: Pour les opérations et les informations détaillées, reportez-vous au MANUEL D’INSTRUCTIONS sur le site web suivant: Para obtener más información y detalles sobre las operaciones, consulte el MANUAL DE INSTRUCCIONES en el siguiente sitio w
KW-R940BTS: CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Important Notice concerning the Software -jansson Copyright (c) 2009-2012 Petri Lehtinen
sha2 AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/ Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved. Author: Chris G. Demetriou Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved.
T-Kernel 2.0 This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum (www.tron.org) BSD-3-Clause Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved. You may obtain a copy of the license at https://opensource.org/licenses/BSD-3-Clause THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
Installation/Connection This section is for the professional installer. For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer. WARNING • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
Wiring connection Antenna terminal Vehicle dashboard Fuse (10 A) Factory wiring harness (vehicle) Join the same color wires together.
Before Use IMPORTANT Basics (on faceplate) KW-X840BTS: • To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide. • Please keep the Guide in a safe and accessible place for future reference. How to reset Eject button and loading slot WARNING Display window*1 Do not operate any function that takes your attention away from safe driving.
Getting Started 3 Set the basic settings 1 Press and hold MENU. 2 Turn the volume knob to select an item (see the following table), then 1 Cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES]), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB” 1 Press the volume knob. press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press MENU to exit.
Radio Search for a station 1 Press SOURCE B repeatedly to select FM or AM. 2 Press S / T to search for a station automatically. (or) Press and hold S / T until “M” flashes, then press repeatedly to search for a station manually. CD/USB/iPod Selectable source: • KW-R940BTS: CD/USB/iPod USB or iPod BT • KW-X840BTS: USB/iPod USB or iPod BT Start playback The source changes automatically and playback starts when you load a disc or attach a device (USB device/ iPod/iPhone) to the USB input terminal.
Menu Settings Examples of some well-used settings 1 2 3 4 1 Press and hold Subwoofer Level Setting Press and hold MENU to enter menu settings. Turn the volume knob to select an item, then press the knob. Repeat step 2 until the desired item is selected/activated. Press MENU to exit. To return to the previous setting item, press . • Refer to the INSTRUCTION MANUAL on the following website for the detailed explanation of each item:
8 Press MENU to exit the setting menu. Illumination Color Setting You can set your preferred illumination color for each zone. 5 Turn the volume knob to choose a color, then press the knob. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown. • [COLOR FLOW01] to [COLOR FLOW03]: Color changes at different speeds. • [CRYSTAL]/[FLOWER]/[FOREST]/[GRADATION]/[OCEAN]/ [RELAX]/[SUNSET]: The selected color pattern is shown.
(B) “[Device Name]” “VOL – YES” “BACK – NO” Press the volume knob to start pairing. • If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device. • If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
U.S.A. JVCKENWOOD USA Cor oration TO OUR VALUED CUSTOMER THANK YOU FOR PURCHASING THIS JVC PRODUCT. WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE. JVC LIMITED WARRANTY ONLY FOR PRODUCT PURCHASED IN U.S.A. JVCKENWOOD USA Corporation warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIG INAL RETAIL PURCHASER to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original purchase for the period shown below.
CANADA Jvc JVCKENWDOD CANADA INC. GARANTIE WARRANTY Warranty applies only to PRODUCT distributed in Canada by JVCKENWOOO CANADA INC. JVCKENWOOO CANADA INC. (hereafter called "JVC") gives the following express warranty for each new JVC product distributed in Canada by JVC and sold by an authorized JVC dealer.
SOFTWARE LICENSE AGREEMENT The software embedded in the Product (hereinafter the 'Licensed Software') provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Important Notice concerning the Software -cJSON Copyright (c) 2009 Dave Gamble Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software Is furnished to do so, subject to the following conditions: