KW-M180DBT KW-M180BT MONITOR WITH RECEIVER INSTRUCTION MANUAL • Updated information (the latest Instruction Manual, etc.) is available from . Model name indication position See “Removing the trim plate” (P.
Contents Before use.................................................................................. 2 How to read this manual.................................................................................... 2 Precautions................................................................................................................. 2 Getting Started........................................................................ 3 Clock settings..................................................................
Getting Started 1 Turn the ignition key of your car to ACC. The unit is turned on, please read the warning and press “Agree” to enter the screen. 2 Press the < 3 Touch [ ]. > button. 4 Touch the corresponding key and set the value. [Guidelines SETUP] If you select [ON] for [Parking Guidelines], you can adjust the parking guidelines. See To adjust the parking guidelines (P.12) [Reverse with ATT (-20dB)] When the gear is shifted to the reverse (R) position, the volume of the device is adjusted.
Basics Basics Functions of the Buttons on the Front Panel ÑÑTurning off the power 1 Press and hold the < > button. 1 2 3 ÑÑAdjusting the volume 1 Press the <+> or <–> button. 4 5 6 1 Remote Sensor • Receives the remote control signal. 2 (HOME) • Displays the HOME screen. (P.5) • Press and hold turns the power off. • When the power off, turns the power on. 3 EQ • Displays the Audio screen.* (P.
Basics HOME screen descriptions 1 Press the < 1 > button. 1 [ [ HOME screen appears. 8 2 5 3 Source control screen ] : Returns to previous screen. ] : Displays the Audio screen. (P.16) 4 1 6 7 1 Clock display Touch to displays the Clock screen. 2 Switchesto the digital radio broadcast. * (P.6) * Only KW-M180DBT 3 Switches to the radio broadcast. (P.7) 4 Switches to an external component connected to the AV-IN input terminal. (P.11) 5 Displays the Hands Free screen. (P.
Digital RadioRadio (KW-M180DBT) Digital (KW-M180DBT) Digital Radio Basic Operation Digital Radio Setup 1 Press the < > button. 2 Touch [Digital Radio]. 1 Touch [ ]. 2 Set each item as follows. ÑÑSource control screen 1 2 3 1 Displays the information of the current service: Service name, Ensemble name, PTY Genre, Channel 2 [DAB] : Switches the Digital Radio preset band. “DAB1”, “DAB2”, “DAB3” [DLS] : Display the Dynamic Label Segment screen [E] [F] : Select an ensemble, service, and component.
Tuner Tuner Tuner Basic Operation Tuner Setup 1 Press the < > button. 2 Touch [Tuner]. 1 Touch [ ]. 2 Set each item as follows. ÑÑSource control screen 1 2 3 1 Displays the information of the current station: PS name, Frequency, PTY Genre, Indicator Items 2 [FM] : Switches the FM band. “FM1”, “FM2”, “FM3” [AM] : Switches the AM band. “AM1”, “AM2” [E] [F] : Tunes in a station with good reception automatically. [ ] : Displays the Tuner Setup screen. (P.7) 3 Recalls the memorized station.
USB USB ÑÑFor Video playback Preparation 1 When the operation buttons are not displayed ÑÑConnecting a USB device 1 Remove the cap of the USB terminal. 2 Connect the USB device with the USB cable. The unit reads the device and playback starts. 5 6 ÑÑTo disconnect the USB device 1 Press the < > button. 2 Touch a source other than [USB]. 3 Detach the USB device. 5 [ ÑÑUsable USB device This unit can play MPEG1/ MPEG2/ MPEG4/ H.263/ H.264/H.
iPhone iPhone Preparation Playback operations ÑÑConnecting iPhone • For details about connecting iPhone, see page 23. ÑÑControl the music you are listening to on the source control screen. 1 Remove the cap of the USB terminal. 2 Connect the iPhone. The unit reads the device and playback starts. ÑÑTo disconnect the iPhone 1 Press the < > button. 2 Touch a source other than [iPhone]. 3 Detach the iPhone. ÑÑConnectable iPhone The following models can be connected to this unit.
Mirroring Mirroring Preparation You can display and control the App on the unit while your smartphone is connected to the USB terminal. ✎✎NOTE • Pair your smartphone with the unit via Bluetooth. See Register your smartphone to the unit (P.13) and Connect the Bluetooth device. ÑÑCompatible Android smartphone • Android version 7.0 or later • Bluetooth support ÑÑTo disconnect the Android smartphone 1 Press the < > button. 2 Touch a source other than [Mirroring]. 3 Detach the Android smartphone.
External Components External Components Using external audio/video players ÑÑStarting playback 1 Connect an external component to the AV-IN input terminal. (P.22) 2 Press the < > button. 3 Touch [AV-IN]. 4 Turn on the connected component and start playing the source. Rear view camera To use a rear view camera, the REVERSE lead connection is required. For connecting a rear view camera. (P.
External Components ÑÑTo adjust the parking guidelines ✎✎NOTE • Install the rear view camera in the appropriate position according to the instruction manual supplied with the rear view camera. • When adjusting the parking guidelines, make sure to apply the parking brake to prevent the car from moving. 1 Press the < > button. 2 Touch [ ]. 3 Touch [System]. 4 Touch [T] or [U] of [Parking Guidelines] and set to [ON].
Bluetooth Bluetooth ÑÑAbout the Bluetooth smartphone and Bluetooth audio player This unit conforms to the following Bluetooth specifications: Version Bluetooth Ver.5.0 Profile Smartphone/ Cell-phone: HFP (V1.6) (Hands Free Profile) PBAP (Phonebook Access Profile) Audio player: A2DP (Advanced Audio Distribution Profile) AVRCP (V1.
Bluetooth Receive a phone call Make a phone call 1 Touch [Û]. 1 Press the < > button. 2 Touch [Phone]. 3 See the table below for each operation method. • [Ý] : Reject an incoming call. ÑÑOperations during a call Call by entering a phone number 1) Enter a phone number with number keys. 2) Touch [Û]. Make a call • Touch [ ] to delete the last entry. Call using call records [Ý] [ Ending a call ] Mute your voice You can send tones by touching desired keys on the screen. • Touch [6] to close the window.
Bluetooth Call by voice You can make a voice call using the voice recognition function of the Bluetooth smartphone. 1) Touch [ ]. 2) Say the name registered in the Bluetooth smartphone. • Touch [Cancel] to cancel voice dialing. Call Waiting When you receive a new call while talking on the phone: 1) Touch [ ] , the current call is put on hold and you can answer the newly received call. 2) Each time you touch [ ], the caller will change to the other one.
Controlling Controlling Audio Audio You can adjust various settings such as audio balance or subwoofer level. 1 Press the button. 2 See the below for each operation method. Equalizer Control 1 Press the button. 2 Touch [Equalizer]. 3 Set each item as follows. 4 1 2 Controlling General Audio 1 Press the button. 2 Touch [Fader / Balance]. 3 Set each item as follows. 4 Initialize the current EQ curve. [Fader Balance] Adjust the left and right volume Balance balance.
Controlling Audio Speaker / X’over setup Listening Position DTA 1 Press the button. 2 Touch [Speaker / X’over]. 3 Touch the speaker to set up. 1 Press the button. 2 Touch [Position / DTA]. 3 Touch [Delay]. 4 Touch [T] or [U] to adjust the delay time of the selected speaker. 4 Set each item as follows. Mode [OFF], [ON] [ON] : Filter adjustment. [OFF] : Turns off the filter. Slope [R] [S] Set a crossover slope. Frequence [R] [S] • High Pass Filter adjustment.
Remote control This unit can be operated using the remote control. The remote control RM-RK258 (optional accessory) can be used. WARNINGS • Do not ingest the battery, Chemical Burn Hazard The remote control supplied with this product contains a coin/button cell battery. If the coin/ button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children.
Installation Installation Before Installation Before installation of this unit, please note the following precautions. #WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Installation ÑÑSupplied accessories for installation 1 ÑÑNon-Japanese cars x2 x1 3 4 x1 5 Installing the unit 2 (3 m) x1 (2 m) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. x1 ÑÑInstallation procedure 1) To prevent a short circuit, remove the key from the ignition and disconnect the ¤ terminal of the battery. 2) Make the proper input and output wire connections for each unit. 3) Connect the wire on the wiring harness.
Installation ÑÑMicrophone unit ÑÑRemoving the unit 1) Check the installation position of the microphone (accessory 4). 2) Clean the installation surface. 3) Remove the separator of the microphone (accessory 4), and stick the microphone to the place shown below. 4) Wire the microphone cable up to the unit with it secured at several positions using tape or other desired method. 5) Adjust the direction of the microphone (accessory 4) to the driver.
Installation ÑÑConnecting wires to terminals REMOTE CONT STEERING WHEEL REMOTE INPUT Light Blue/Yellow (Steering remote control wire) Bright Green/Red ST REMOTE INPUT 1 To steering remote To use the steering wheel remote control feature, you need an exclusive remote adapter (not supplied) matched to your car. PRK SW Gray/Red ST REMOTE GND Light Green (Parking sensor wire) Accessory 9: Extension cable Connect to the vehicle’s parking brake detection switch harness.
Installation ÑÑWiring harness connector function guide ÑÑConnecting an iPhone/Android Pin Color and function A-4 Yellow Battery A-5 Blue[1] Power Control A-7 Red Ignition (ACC) A-8 Black Earth (Ground) Connection B-1/ B-2 Purple (+) / Purple/Black (–) Rear Right B-3/ B-4 Gray (+) / Gray/Black (–) Front Right B-5/ B-6 White (+) / White/Black (–) Front Left B-7/ B-8 Green (+) / Green/Black (–) Rear Left [1] Max.
About this Unit About this Unit ÑÑAcceptable Video files More information ÑÑUsable USB device This unit can play MPEG1/ MPEG2/ MPEG4/H.264/ MKV/ MP3/WMA/ AAC/ WAV/ FLAC/ OGG files stored in a USB mass storage class device. • File system: FAT16 / FAT32 / NTFS / exFAT • This unit can recognize a total of 9,999 files and 320 folders (a maximum of 9,999 files per folder).
About this Unit Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. • For operations with the external components, refer also to the instructions supplied with the adapters used for the connections (as well as the instructions supplied with the external components). ÑÑGeneral No sound comes out of the speakers. • Adjust the volume to the optimum level. • Check the cords and connections. The unit does not work at all.
About this Unit Copyrights • The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards.
About this Unit Specifications ÑÑMonitor section Picture Size : 6.75 inches (diagonal) wide : 1 51.8 mm (W) × 79.7 mm (H) Display System : Transparent TN LCD panel Drive System : TFT active matrix system Number of Pixels : 1,152,000 (800H x 480V x RGB) Effective Pixels : 99.99 % Pixel Arrangement : RGB striped arrangement Back Lighting : LED ÑÑUSB interface section USB Standard : USB 2.0 High Speed File System : FAT16 / FAT32 / NTFS / exFAT Maximum Power Supply Current : DC 5 V 1.
About this Unit ÑÑFM tuner section ÑÑDSP section Frequency Range (step) : 8 7.5 MHz – 108.0 MHz (50 kHz) Usable Sensitivity : 16.2 dBf : 1 .8 μV/75 Ω (S/N : 30 dB) Frequency Response : 30 Hz – 14 kHz S/N Ratio (dB) : 50 dB (MONO) Stereo Separation : 35 dB (1 kHz) Equalizer Band : 13 Band Frequency: 62.5/100/160/250/400/630/1k/1.6k/2.5k/ 4k/6.3k/10k/16kHz Level: -9 – +9 dB X’Over • High pass filter Frequency: Through / 30/40/50/60/70/80/90/100/ 120/150/180/220/250 Hz Slope: -6/-12/-18/-24 dB/Oct.
About this Unit ÑÑInformation on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems) Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts.
About this Unit English Hereby, JVCKENWOOD declares that the radio equipment “KW-M180DBT”/”KWM180BT” is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: Français Par la présente, JVCKENWOOD déclare que l’équipement radio “KW-M180DBT”/”KWM180BT” est conforme à la directive 2014/53/UE.