KD-X560BT DIGITAL MEDIA RECEIVER INSTRUCTION MANUAL • Updated information (the latest Instruction Manual, etc.) is available from . © 2019 JVC KENWOOD Corporation KD-X560BT_K_1ENG.
Contents Before use................................................................................. 2 How to read this manual...................................................................................2 Precautions................................................................................................................2 Getting Started....................................................................... 3 Initial settings......................................................................
Getting Started Initial settings Clock settings ÑÑSynchronizing the clock time with FM RDS Activate [RDS Clock Sync]. See “Tuner function settings” (P.8). ÑÑAdjusting the clock manually 1 Turn the ignition key of your car to ACC. The unit is turned on. 2 Turn the volume knob to select the item to set (see the table below), then press the knob to make a selection. ✎✎NOTE • Deactivate [RDS Clock Sync] before adjusting the clock. See “Tuner function settings” (P.8).
Basics Basics Volume knob (turn/press) Detach button Common operations Select a source 1 Press < > to display the HOME screen. HOME screen appears. ÑÑTurning on the power 1 Press < >. 2 Turn the volume knob to select the source, then ÑÑTurning off the power 1 Press and hold < Remote sensor Monitor press the knob. 1 >. ÑÑAdjusting the volume 2 3 5 6 4 1 Turn the volume knob. ÑÑMutes the sound 1 Press and hold the volume knob. appears when the mute function is active.
USB USB Preparation Playback operations ÑÑConnecting a USB device 1 Open the front port cover. 2 Connect the USB device with the USB cable (sold separately). Audio files/Video files The unit reads the device and playback starts. • USB maximum power supply current : DC 5 V = 1 A ÑÑTo disconnect the USB device: 1 Press < > to display the HOME screen. 2 Turn the volume knob to select other than [USB], then press the knob. 3 Detach the USB device.
USB ÑÑSelecting a track in a list (Searches file) 1 Press < > to display the LIST screen. 2 Press / to select whether you search by audio files [ picture files [ ]. ], video files [ ] or Function settings 1 Press < > to display the function menu. 2 Turn the volume knob to select the item to set (see the table below), then press the knob to make a selection. 3 Press < 3 Turn the volume knob to select the desired folder, then press the knob. • When you select a folder its contents are displayed.
iPod/iPhone iPod/iPhone Preparation ÑÑSource screen ÑÑConnecting iPod/iPhone 1 Open the front port cover. 2 Connect the iPod/iPhone using the KS-U62 2 (optional accessory). 1 The unit reads the device and playback starts. • USB maximum power supply current : DC 5 V = 1 A ÑÑTo disconnect the iPod/iPhone 1 Press < > to display the HOME screen. 2 Turn the volume knob to select other than [iPod], then press the knob. 3 Detach the iPod/iPhone.
Tuner Tuner Tuner basic operations Tuner function settings 1 Press < > to display the function menu. 2 Turn the volume knob to select the item to set (see the table below), then press the knob to make a selection. 3 Press < Manual Store 1 Press < > to display the HOME screen. 2 Turn the volume knob to select [FM] or [AM], then press the knob. 3 Press / to search for a station automatically. “Auto Seek” appears. (or) Press and hold / repeatedly to search for a station manually.
External Components Using external audio players Rear view camera To use a rear view camera, the REVERSE lead connection is required. For connecting a rear view camera. (P.18) 1 2 1 3.5 mm stereo mini plug (Sold separately) Use a 3-core plug head stereo mini plug for optimum audio output. 2 Portable audio player (Sold separately) ÑÑDisplaying the picture from the rear view camera The rear view screen is displayed when you shift the gear to the reverse (R) position.
Bluetooth® smartphone Bluetooth® smartphone ÑÑAbout the Bluetooth smartphone and Bluetooth audio player Receive a call This unit conforms to the following Bluetooth specifications: Version Bluetooth Ver.4.
Bluetooth® smartphone Make a phone call Playing Bluetooth Audio Device 1 Press < 1 Press < > to display the HOME screen. 2 Turn the volume knob to select [BT Audio], then > to enter Bluetooth mode. press the knob. To Do this Play/pause Press the volume knob. Select a file Press / repeatedly. Fast-backward/ Press and hold /. Fast-forward 2 Press / to select a method to make a call ([ ]: from the calls history/[ the phone book).
Bluetooth smartphone Setup Function settings Settings 1 Press < > to display the function menu. 2 Turn the volume knob to select the item to set (see the table below), then press the knob to make a selection. 3 Press < Repeat Random > to exit. All: Repeats all files. ( indicator lights up.) One: Repeats current file. ( indicator lights up.) OFF: Repeat off. OFF: Normal playback. All: Randomly plays all files. ( indicator lights up.) 1 Press and hold < > to display the settings.
Setup Bluetooth Settings X’over Sync ON/OFF: Activates or deactivates the Phonebook synchronization of the phonebook in the connected smartphone with the unit. BT Displays the information about the Information connected Bluetooth device (device name, phone name, and mac address). Sound settings 1 Press < Delay You can set the crossover frequency of speakers. 1) Press / to select the speaker. 2) Press the volume knob to select the item. 3) Turn the volume knob to adjust the value. 4) Press < >.
Remote control This unit can be operated using the remote control. The remote control RM-RK258 (optional accessory) can be used. Functions of the remote control buttons • Aim the remote control directly at the remote sensor on the faceplate. • DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting). SRC VOL + – ATT DISP FM/R AM/S E 2 F 3 ANGLE Û DIRECT ASPECT Numeric Keypad CLR ENT Switches to the source to be played. Adjusts the volume.
Installation Installation Before installation Before installation of this unit, please note the following precautions. #WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Installation ÑÑInstallation procedure ÑÑTrim plate 1) To prevent a short circuit, remove the key from the ignition and disconnect the ¤ terminal of the battery. 2) Make the proper input and output wire connections for each unit. 3) Connect the wire on the wiring harness. 4) Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5) Take Connector A on the wiring harness and connect it to the external power connector on your vehicle.
Installation ÑÑRemoving the trim plate 1) Use the extraction key (accessory 4) to lever out the four tabs (two on the top part, two on the bottom part). 4 2) Pull the trim plate forward. ÑÑRemoving the unit 1) Remove the trim plate by referring to step 1 in “Removing the trim plate”. 2) Detach the faceplate. 1 2 3) Insert the two extraction key (accessory 3) deeply into the slots on each side, as shown.
Installation ÑÑConnecting wires to terminals Connect to the vehicle’s parking brake detection switch harness. PRK SW Light Green (Parking sensor wire) For best safety, be sure to connect the parking sensor. REVERSE Purple/White (Reverse sensor wire) STEERING WHEEL REMOTE INPUT Connect to vehicle’s reverse lamp harness when using the optional rear view camera.
Installation 15A 1 3 5 7 2 4 6 8 1 3 5 7 2 4 6 8 Accessory 7 Accessory 6 P.CONT ANT.CONT Blue (Power control/ Antenna control wire) Cap Connect either to the power control terminal when using the optional power amplifier, or to the power terminal for the booster amplifier of the film-type or short pole type antenna. (Max.
About this Unit About this Unit Maintenance More information ÑÑCleaning the Unit ÑÑPlayable Audio files If the front panel of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the front panel is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe it again with a clean soft dry cloth. Audio format Bit rate/ Bit count MP3 (.mp3) 32 – 320kbps, VBR WMA (.wma) 16 – 384kbps AAC-LC (.m4a) 16 – 448kbps WAV (.wav) 16/24 bit FLAC (.
About this Unit Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. • For operations with the external components, refer also to the instructions supplied with the adapters used for the connections (as well as the instructions supplied with the external components). ÑÑGeneral No sound comes out of the speakers. • Adjust the volume to the optimum level. • Check the cords and connections. The unit does not work at all.
About this Unit Specifications ÑÑMonitor section Picture Size : 3.0 inch display Drive System : TFT active matrix system Number of Pixels : 320H x 240V Aspect Ratio : 16:9(wide) Back Lighting : LED ÑÑUSB interface section USB Standard : USB 2.0 High Speed File System : FAT 16/ 32, NTFS Maximum Power Supply Current : DC 5 V 1.0 A Frequency Response : 20 – 20,000 Hz Audio Decoder : MP3/ WMA/ AAC/ WAV/ FLAC/ OGG Video Decoder : MPEG1/ MPEG2/ MPEG4/ H.
About this Unit ÑÑAudio section Maximum Power (Front & Rear) : 45 W × 4 Full Bandwidth Power (1% THD) : 16 W × 4 Preout Impedance : 10 kΩ Preout Level/Load : 2.0 V/10 kΩ Speaker Impedance :4–8Ω ÑÑGeneral Operating Voltage : 12 V DC car battery Installation Dimensions (W × H × D) : 182 × 52 × 117 mm (with sleeve) 7-3/16 × 2-1/16 × 4-5/8 inch Weight : 0.75 kg (1.65 lbs) NOTE • Although the effective pixels for the liquid crystal panel is given as 99.99% or more, 0.
About this Unit Copyrights • The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards.
About this Unit THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
About this Unit For USA ÑÑFCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. NOTE • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
About this Unit For Argentina ÑÑInformación acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos) Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos.
KD-X560BT_K_1ENG.