ENGLISH FRANÇAIS ESPAÑOL KD-X470BHS / KD-X370BTS / KD-X37MBS / KD-X270BT / KD-SX26BT DIGITAL MEDIA RECEIVER INSTRUCTION MANUAL RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE MANUEL D’INSTRUCTIONS RECEPTOR DE MEDIOS DIGITALES MANUAL DE INSTRUCCIONES For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No. B5A-3105-00 [K] JS_JVC_KD_X470BHS_K_C.
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos) Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos.
IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Important Notice concerning the Software -CMP -jansson The MIT License (MIT) Copyright (c) 2014 Charles Gunyon Copyright (c) 2009-2012 Petri Lehtinen
Contents Before Use ................................................................................................. 3 References .............................................................................................. 37 Basics ......................................................................................................... 4 Maintenance Getting Started ........................................................................................
Before Use IMPORTANT • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings and Cautions in this manual. • Please keep the manual in a safe and accessible place for future reference. WARNING • Do not operate any function that takes your attention away from safe driving. • Do not ingest the battery, Chemical Burn Hazard. The remote control supplied with this product contains a coin/button cell battery.
Basics Faceplate Attach KD-X470BHS/KD-X370BTS/KD-X37MBS: Volume knob Display window* Detach Detach button How to reset KD-X270BT/KD-SX26BT: Reset the unit within 5 seconds after detaching the faceplate. * Only for illustration purpose. To On the faceplate Turn on the power Press B SRC. • Press and hold to turn off the power. Adjust the volume Turn the volume knob. Press the volume knob to mute the sound or pause playback. • Press again to cancel.
Getting Started Basics Remote control (RM-RK52) (except for KD-SX26BT) This unit can be remotely controlled with an optionally purchased remote control. Remote sensor (Do not expose to bright sunlight.) 1 Cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], see page 6), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB” Pull out the insulation sheet when using for the first time. 1 Press the volume knob. [YES] is selected for the initial setup.
Getting Started 9 Press to exit. To return to the previous setting item, press 3 [F/W UPDATE] . [UPDATE SYSTEM]/[UPDATE HD] [F/W UP xxxx]/ [F/W UP Vxx] Set the basic settings . 1 Press and hold 2 Turn the volume knob to select an item (see the following table), then [FACTORY RESET] press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit. To return to the previous setting item, press Default: [XX] (Not applicable when 3-way crossover is selected.
HD Radio™ Tuner (for KD-X470BHS) You can tune in to both conventional and HD Radio broadcasts. • To find HD Radio stations in your area, visit . 2 Turn the volume knob to select a preset number, then press the knob. “MEMORY” appears once the station or channel is stored. Select a stored station or channel Press one of the number buttons (1 to 6). (or) 1 Press to enter HD search select mode. 2 Turn the volume knob to select [PRESET LIST], then press the knob.
HD Radio™ Tuner (for KD-X470BHS) Display received emergency alert messages 4 Set the activation day*2 and time. “M” indicator lights up when complete. The received emergency alert messages are stored in the Alert Message List, and you can check them later. While listening to the HD RADIO source... 1 Press to enter HD search select mode. 2 Turn the volume knob to select [ALRT MSG LIST], then press the knob.
Radio (for KD-X370BTS/KD-X37MBS/KD-X270BT/KD-SX26BT) Select a stored station Press one of the number buttons (1 to 6). (or) 1 Press . 2 Turn the volume knob to select a preset number, then press the knob. Other settings Search for a station 1 Press B SRC repeatedly to select FM or AM. 2 Press S / T (or press H / I on the remote control) to search for a station automatically.
Radio (for KD-X370BTS/KD-X37MBS/KD-X270BT/KD-SX26BT) [SSM] [SSM 01–06]/[SSM 07–12]/[SSM 13–18]: Automatically presets up to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select [SSM 07–12]/[SSM 13–18] to store the following 12 stations. [IF BAND] [AUTO]: Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.
USB/iPod Select music drive Basic operations While in USB source, press 5 MODE repeatedly. Stored songs in the following drive will be played back. • Selected internal or external memory of a smartphone (Mass Storage Class). • Selected drive of a multiple drive device. Selectable source: • KD-X470BHS/KD-X370BTS/KD-X37MBS: USB/iPod USB or iPod BT • KD-X270BT/KD-SX26BT: USB Select control mode While in iPod USB source (or iPod BT source), press 5 MODE repeatedly.
AUX USB/iPod Quick search (applicable only for USB source) If you have many files, you can search through them quickly. 1 2 3 4 Press . Turn the volume knob to select a folder/list, then press the knob. Turn the volume knob quickly to browse through the list quickly. Turn the volume knob to select a file, then press the knob. Selected file starts playing. You can listen to music from a portable audio player via the auxiliary input jack. Preparation: Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT].
Pandora® You can listen to Pandora on the following device: To On the faceplate On the remote control • KD-X470BHS/KD-X370BTS/KD-X37MBS: iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth) • KD-X270BT/KD-SX26BT: Android device (via Bluetooth) Play back/pause Press the volume knob. Press d. Skip a track Press T. Press I. Select thumbs up or thumbs down* Press 2 J / 1 K. Press J / K.
Pandora® Bookmark current song information Press and hold the volume knob. “BOOKMARKED” appears and the information is stored to your device. • The bookmark is available on your Pandora account but not on this unit.
Spotify To On the faceplate Play back/pause Press the volume knob. Press d. Skip a track Press S*1 / T. Press H*1 / I. Select thumbs up or thumbs down *2 Press 2 J / 1 K. Press J / K. Start radio Press and hold 5. ( Not available ) Repeat play*3 Press 4 B repeatedly. [ALL REPEAT], [ONE REPEAT]*1, [REPEAT OFF] Random play*3 Press 3 A repeatedly *1. [ALL RANDOM], [RANDOM OFF] On the remote control ( Not available ) Search for a song or station .
SiriusXM® Radio (for KD-X470BHS/KD-X370BTS/KD-X37MBS) Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit . Preparation: 1 Connect the optional SiriusXM Vehicle Tuner (commercially available).
SiriusXM® Radio (for KD-X470BHS/KD-X370BTS/KD-X37MBS) Select a stored channel SmartFavorites and TuneStart™ Press one of the number buttons (1 to 6) (or press J / K on the remote control). (or) 1 Press . 2 Turn the volume knob to select PRESET, then press the knob. 3 Turn the volume knob to select a preset number, then press the knob. User preset channels are initially assigned as the SmartFavorites channels. SmartFavorite channel is available with SXV200 or later SiriusXM tuner models.
SiriusXM® Radio (for KD-X470BHS/KD-X370BTS/KD-X37MBS) To On the faceplate Select a stored SmartFavorite channel Press one of the number buttons (1 to 6). 1 Press . 2 Turn the volume knob to select PRESET, then press the knob. 3 Turn the volume knob to select a preset number, then press the knob. Cancel SmartFavorites channels 1 Press . 2 Turn the volume knob to select PRESET, then press the knob. 3 Turn the volume knob to select a preset number, then press and hold the knob.
SiriusXM® Radio (for KD-X470BHS/KD-X370BTS/KD-X37MBS) [CODE SET] 1 2 3 4 5 6 • Press the volume knob to enter [NEW CODE]. Turn the volume knob to select a number. Press S / T to move to the entry position. Repeat step 2 and step 3 to enter a new 4-digit pass code. Press the volume knob to confirm. Repeat step 2 to step 5 to reconfirm the pass code. Make a note of the new pass code to enter channel lock settings for next time. [LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting.
Bluetooth® Using Other Applications 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit. To return to the previous setting item, press . Default: [XX] [REMOTE APP] [SELECT] [IOS] (For KD-X470BHS/KD-X370BTS/KD-X37MBS) Selects the device ([IOS] or [ANDROID]) to use the application. [YES]: Selects iPhone/iPod touch to use the application via Bluetooth or connected via USB input terminal. ; [NO]: Cancels.
Bluetooth® Pair and connect a Bluetooth device for the first time 1 Press B SRC to turn on the unit. 2 Search and select the name of your receiver (“KD-X470BHS”/ “KD-X370BTS”/“KD-X37MBS”/“KD-X270BT”/“KD-SX26BT”) on the Bluetooth device. “BT PAIRING” flashes on the display. • For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching. 3 Perform (A) or (B) depending on what appears on the display.
Bluetooth® Bluetooth — Mobile phone The following operations may differ or be unavailable depending on the connected phone. To On the faceplate On the remote control Answer a call Press or the volume knob. Press J / K / H / I. Reject a call Press and hold or the volume knob. Press and hold J / K / H / I. End a call Press and hold or the volume knob. Press and hold J / K / H / I. First incoming call...
Bluetooth® *1 This adjustment will not affect the volume of the other sources. *2 Press and hold VOL + to continuously increase the volume to 15. *3 Operations may vary according to the connected Bluetooth device. Default: [XX] [SETTINGS] [AUTO ANSWER] [01 SEC] to [30 SEC]: Answers an incoming call automatically in the selected time (in seconds). ; [OFF]: Cancels. Improve the voice quality While talking on the phone...
Bluetooth® [RECENT CALL] [PHONEBOOK] (Applicable only if the phone supports PBAP.) 1 Press the volume knob to select a name or a phone number. • “<” indicates call received, “>“ indicates call made, “M” indicates call missed. • “NO HISTORY” appears if there is no recorded call history or call number. 2 Press the volume knob to call. You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode.
Bluetooth® Default: [XX] [BT MODE] [PHONE SELECT] [AUDIO SELECT] Selects the phone or audio device to connect or disconnect. “ ” appears in front of the device name when connected. “ ” appears in front of the current playback audio device. • You can connect a maximum of two Bluetooth phones and one Bluetooth audio device at a time. Bluetooth compatibility check mode You can check the connectivity of the supported profile between the Bluetooth device and the unit.
Bluetooth® The connectivity result flashes on the display. “PAIRING OK” and/or “HANDS-FREE OK”*1 and/or “AUD.STREAM OK”*2 and/ or “PBAP OK”*3: Compatible Bluetooth — Audio *1 Compatible with Hands-Free Profile (HFP) *2 Compatible with Advanced Audio Distribution Profile (A2DP) *3 Compatible with Phonebook Access profile (PBAP) After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has been deleted, and the unit exits check mode.
AMAZON ALEXA (for KD-X470BHS/KD-X370BTS/KD-X37MBS) Bluetooth® To Repeat play On the faceplate Press 4 B repeatedly. [TRACK REPEAT], [ALL REPEAT], [GROUP REPEAT]*1, [REPEAT OFF] Random play On the remote control ( Not available ) Press 3 A repeatedly. [GROUP RANDOM]*1, [ALL RANDOM], [RANDOM OFF] Select a file from a folder/list Refer to “Select a file to play” on page 11. Switch between connected Bluetooth audio devices Press 5.
AMAZON ALEXA (for KD-X470BHS/KD-X370BTS/KD-X37MBS) • The Alexa connection can be disconnected if: – A2DP profile is disconnected – Bluetooth is disconnected – This unit is turned off – Any other conditions depending on the connected device. To establish Alexa connection again, reconnect the A2DP profile.
AMAZON ALEXA (for KD-X470BHS/KD-X370BTS/KD-X37MBS) Audio Settings Start listening While in Alexa idle state... 1 Press on the unit to activate Alexa. The display shows: “LISTENING...”. 2 Communicate with Alexa via the connected microphone. (Page 20) 3 During music playback in ALEXA source, you can perform the following operations: To On the faceplate On the remote control Play back/pause Press the volume knob. Press d. Reverse skip/ Forward skip Press S / T. Press H / I. 1 Press and hold .
Audio Settings [PRO EQ] Adjusts your own sound settings for each source. • The settings are stored to [USER] in [PRESET EQ]. • The settings made may affect the current settings of [EASY EQ]. [62.5HZ] [LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) [ON]: Turns on the extended bass. ; [OFF]: Cancels. [100HZ]/[160HZ]/[250HZ]/[400HZ]/[630HZ]/[1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/ [6.
Audio Settings Speaker output settings [SPK/PRE OUT] [SOUND EFFECT] [SPACE ENHANCE] (Not applicable for FM/AM source.) [SMALL]/[MEDIUM]/[LARGE]: Virtually enhances the sound space. ; [OFF]: Cancels. [SND RESPONSE] [LEVEL1]/[LEVEL2]/[LEVEL3]: Virtually makes the sound more realistic. ; [OFF]: Cancels. [SOUND LIFT] [LOW]/[MIDDLE]/[HIGH]: Virtually adjusts the sound position heard from the speakers. ; [OFF]: Cancels.
Audio Settings Connection via speaker leads Crossover settings You can also connect the speakers without using an external amplifier but still being able to enjoy the subwoofer output with these settings. (Page 45) Below are the available setting items for 2-way crossover and 3-way crossover. CAUTION Setting on [SPK/PRE OUT] Audio signal through rear speaker lead L (left) R (right) Rear speakers output Rear speakers output [REAR/SUB.W]* Rear speakers output Rear speakers output [SUB.W/SUB.
Audio Settings 2-way crossover setting items [SUBWOOFER LPF]*2*3 [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/ [90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/ [220HZ]/[250HZ]/[THROUGH] [3.5"]/[4"]/[4.75"]/[5"]/[6.5"]/[6.75"]/[7"]/ [4×6]/[5×7]/[6×8]/[6×9]/[7×10] [SW LPF SLOPE] [–06DB]/[–12DB]/[–18DB]/[–24DB] [SMALL]/[MIDDLE]/[LARGE]/[NONE] (not connected) [SW LPF GAIN] [SPEAKER SIZE] [FRONT] [SIZE] [TWEETER] [REAR]*1 [3.5"]/[4"]/[4.75"]/[5"]/[6.5"]/[6.
Audio Settings [MID RANGE] [HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/ [100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]/ [THROUGH] [HPF SLOPE] [–06DB]/[–12DB] [LPF FRQ] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.3KHZ]/ [8KHZ]/[10KHZ]/[12.5KHZ]/[THROUGH] [LPF SLOPE] [–06DB]/[–12DB] Digital Time Alignment sets the delay time of the speaker output to create a more suitable environment for your vehicle. • For more information, see “Determining the delay time automatically” on page 35.
Display Settings Audio Settings Determining the delay time automatically If you specify the distance from the currently set listening position to every speaker, the delay time will be automatically calculated. 1 Set [POSITION] and determine the listening position as the reference point (the reference point for [FRONT ALL] will be the center between the right and left in the front seats). 2 Measure the distances from the reference point to the speakers.
Display Settings 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the knob. *1 The illumination control wire connection is required. (Page 45) *2 Some characters or symbols will not be shown correctly (or will be blank). *3 Functionality depends on the type of phone used. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. to exit.
References Maintenance Cleaning the unit Wipe off dirt on the faceplate with a dry silicone or soft cloth. Cleaning the connector Detach the faceplate and clean the connector gently with a cotton swab. Be careful not to damage the connector. Connector (on the reverse side of the faceplate) More information For: – Latest firmware updates and latest compatible item list – JVC original application – Any other latest information Visit .
References About AMAZON ALEXA • Alexa is a third party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable. Change the display information Each time you press , the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO NAME”, or other information (eg. station name) appears or display will be blank.
References BT AUDIO/ALEXA Song title (Artist) Song title (Artist) with Music Synchronization Effect*2 Song title (Album title) Song title (Date) Playing time (Date) back to the beginning Frequency (Date) Frequency (Date) with Music Synchronization Effect*2 back to the beginning AUX Source name (Date) Source name (Date) with Music Synchronization Effect*2 back to the beginning For FM Radio Broadcast Data System stations only: Station name/Program type (Date) Station name/Program type (Date) with Music S
Troubleshooting Source name Display information: Main SPOTIFY BT Context title Context title with Music Synchronization Effect* Song title Artist Album title Playing Time Date back to the beginning BT AUDIO Song title/Artist Song title/Artist with Music Synchronization Effect* Album title/Artist Playing time Date back to the beginning AUX Source name Source name with Music Synchronization Effect* Date back to the beginning Symptom Remedy Sound cannot be heard.
Troubleshooting USB/iPod Remedy Symptom • Check whether the connected USB device is compatible with this unit and ensure the file systems are in supported formats. (Page 37) • Reattach the USB device. “UNRESPONSIVE DEVICE” appears. Make sure the USB device is not malfunction and reattach the USB device. “USB HUB IS NOT SUPPORTED” appears. This unit cannot support a USB device connected via a USB hub. “CANNOT PLAY” appears. Connect a USB device that contains playable audio files.
Troubleshooting Bluetooth® 42 Remedy “CH LOCKED LOCK CODE?” The selected channel is locked. Enter the correct pass code to unlock. (Page 18) “CHAN UNSUB” The selected channel is unsubscribed. Call 1-866-635-2349 in the U.S.A. or 1-877-438-9677 in Canada to subscribe. (Page 16) “CH UNAVAIL” The selected channel is unavailable. For more information about the SiriusXM channel lineup, visit . “CHECK ANTENNA” Check that the antenna and its connection are in good condition.
Installation/Connection Troubleshooting AMAZON ALEXA Bluetooth® Symptom Remedy “H/W ERROR” Reset the unit and try the operation again. If “H/W ERROR” appears again, consult your nearest service center. “SWITCHING NG” The connected phones might not support phone switching feature. The Bluetooth connection between the Bluetooth device and the unit is unstable. Delete the unused registered Bluetooth device from the unit. (Page 25) No response from Alexa after the voice input.
Installation/Connection Part list for installation Installing the unit (in-dash mounting) (A) Faceplate (×1) (B) Trim plate (×1) (C) Mounting sleeve (×1) (D) Wiring harness (×1) Do the required wiring. (Page 45) Hook on the top side Orientate the trim plate as illustrated before fitting. Dashboard of your car (E) Extraction key (×2) Bend the appropriate tabs to hold the sleeve firmly in place.
Installation/Connection Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Antenna terminal Vehicle dashboard Fuse (10 A) Light blue/yellow Factory wiring harness (vehicle) To the steering wheel remote control adapter Custom wiring harness (separately purchased) Join the same color wires together.
Installation/Connection Connect external components Connect external amplifiers via output terminals Signal cord (not supplied) JVC Amplifier* Output terminals Remote wire (not supplied) To remote lead (blue/white) of the wiring harness. (Page 45) No Part 1 For KD-X470BHS: MIC (Microphone input terminal) (page 20) 2 For KD-X370BTS/KD-X37MBS: MIC (Microphone input terminal) (page 20) 3 Output terminals (See “Connect external amplifiers via output terminals”.
Specifications KD-X470BHS: Frequency Range FM Frequency Range 87.9 MHz — 107.9 MHz (200 kHz step) 87.5 MHz — 108.0 MHz (50 kHz step) 7.2 dBf (0.63 μV/75 Ω) Usable Sensitivity (S/N = 26 dB) 8.2 dBf (0.71 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46 dB) 15.2 dBf (1.58 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.
Specifications Signal-to-Noise Ratio (1 kHz) KD-X470BHS: 98 dB Dynamic Range 93 dB Channel Separation KD-X470BHS: 92 dB Bluetooth MP3 Decode 48 50 W × 4 or 50 W × 2 + 50 W × 1 (Subwoofer = 4 Ω) Full Bandwidth Power (at less than 1 % THD) 22 W × 4 Speaker Impedance 4Ω—8Ω Preout Level/Load KD-X470BHS: 5 000 mV/10 kΩ KD-X370BTS/KD-X37MBS: 4 000 mV/10 kΩ Compliant with MPEG-1/2 Audio Layer-3 WMA Decode Compliant with Windows Media Audio AAC Decode KD-X470BHS/KD-X370BTS/KD-X37MBS: AAC-LC “.
libFLAC Copyright (C) 2000-2009 Josh Coalson Copyright (C) 2011-2013 Xiph.Org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
ENGLISH FRANÇAIS ESPAÑOL KD-X470BHS / KD-X370BTS / KD-X37MBS / KD-X270BT / KD-SX26BT DIGITAL MEDIA RECEIVER Quick Start Guide RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE Guide de démarrage rapide RECEPTOR DE MEDIOS DIGITALES Guía de inicio rápido For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website: Pour les opérations et les informations détaillées, reportez-vous au MANUEL D’INSTRUCTIONS sur le site web suivant: Para obtener más información y detalles sobre las operacio
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos) Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos.
IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Important Notice concerning the Software -CMP -jansson The MIT License (MIT) Copyright (c) 2014 Charles Gunyon Copyright (c) 2009-2012 Petri Lehtinen
Installation/Connection This section is for the professional installer. For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer. WARNING • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
Installing the unit (without mounting sleeve) 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (commercially available). Wiring connection Antenna terminal Vehicle dashboard Fuse (10 A) Factory wiring harness (vehicle) Use only the specified screws. Using wrong screws might damage the unit. Join the same color wires together.
Before Use Basics (on faceplate) IMPORTANT *1 Only for illustration purpose. • To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide. • Please keep the Guide in a safe and accessible place for future reference.
Getting Started 3 Set the basic settings 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then 1 Cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES]), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB” 1 Press the volume knob. press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.
HD Radio™ Tuner/Radio USB/iPod For KD-X470BHS, you can tune in to both conventional and HD Radio broadcasts. Selectable source: • KD-X470BHS/KD-X370BTS/KD-X37MBS: USB/iPod USB or iPod BT • KD-X270BT/KD-SX26BT: USB Search for a station or channel 1 Press B SRC repeatedly to select FM or AM. 2 For KD-X470BHS: Press and hold to select the tuning mode. • [HD SEEK]: Search for HD Radio broadcast only. • [MANUAL SEEK]: Search for both conventional and HD Radio broadcasts.
Menu Settings Examples of some well-used settings 1 2 3 4 1 Press and hold Subwoofer Level Setting Press and hold to enter menu settings. Turn the volume knob to select an item, then press the knob. Repeat step 2 until the desired item is selected/activated. Press to exit. To return to the previous setting item, press . • Refer to the INSTRUCTION MANUAL on the following website for the detailed explanation of each item:
8 Press to exit the setting menu. Note: For KD-X270BT/KD-SX26BT, you need to set [SPK/PRE OUT] to [REAR/SUB.W] or [SUB.W/SUB.W] before you can make the subwoofer level settings. Illumination Color Setting For KD-X470BHS/KD-X370BTS/KD-X37MBS, you can set your preferred illumination color for each zone. 5 Turn the volume knob to choose a color, then press the knob. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown.
(B) “[Device Name]” “VOL – YES” “BACK – NO” Press the volume knob to start pairing. • If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device. • If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • HD Radio Technology manufactured under license from iBiquity Digital Corporation. U.S. and Foreign Patents. For patents see http://dts.com/patents. HD Radio™ and the HD, HD Radio, and “ARC” logos are registered trademarks or trademarks of iBiquity Digital Corporation in the United States and/or other countries.
WHEN IT IS NOT REQUIRED TO DETACH THE FRONT CONTROL PANEL FROM THE MAIN UNIT, USE THE PROVIDED SCREW TO ATTACH THE CONTROL PANEL TO THE MAIN UNIT.
JVCKENWOOD USA Corporation U.S.A. TO OUR VALUED CUSTOMER THANK YOU FOR PURCHASING THIS JVC PRODUCT. WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE. JVC LIMITED WARRANTY ONLY FOR PRODUCT PURCHASED IN U.S.A. JVCKENWOOD USA Corporation warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL RETAIL PURCHASER to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original purchase for the period shown below.
CANADA Jvc JVCKENWOOD CANADA INC. WARRANTY GARANTIE Warranty applies only to PRODUCT distributed in Canada by JVCKENWOOD CANADA INC. La garantls' applique seulement aux PRODUITS distrlbues au Canada par JVCKENWOOD CANADA INC. JVCKENWOOD CANADA INC. (hereafter called "JVC") gives the following express warranty for each new JVC product distributed in Canada by JVC and sold by an authorized JVC dealer.