ENGLISH FRANÇAIS ESPAÑOL KD-T905BTS / KD-T900BTS / KD-T805BTS / KD-TD90BTS/ KD-T700BT / KD-TD70BT / KD-SR85BT CD RECEIVER INSTRUCTION MANUAL RÉCEPTEUR CD MANUEL D’INSTRUCTIONS RECEPTOR CON CD MANUAL DE INSTRUCCIONES For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No. B5A-2621-10 [K] JS_JVC_KD_T905BTS_K_C.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Notice This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
SOFTWARE LICENSE AGREEMENT The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Article 10 1. 2. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights. Article 11 1. 2. 3. 2. 3.
CONTENTS BEFORE USE BEFORE USE 2 IMPORTANT BASICS 3 GETTING STARTED 4 • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings and Cautions in this manual. • Please keep the manual in a safe and accessible place for future reference.
BASICS Faceplate Volume knob Loading slot Remote control (RM-RK52) (except for KD-SR85BT) This unit can be remotely controlled with an optionally purchased remote control. Remote sensor (Do not expose to bright sunlight.) KD-T905BTS: USB cable from the rear of the unit Detach button Attach KD-T700BT/ Display window KD-TD70BT/ KD-SR85BT Detach How to reset Pull out the insulation sheet when using for the first time.
GETTING STARTED To return to the previous setting item, press 3 . Set the basic settings . 1 Press and hold 2 Turn the volume knob to select an item (see the following table), then 1 Cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], see page 5), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB” 1 Press the volume knob. [YES] is selected for the initial setup. 2 Press the volume knob again. “DEMO OFF” appears. press the knob.
GETTING STARTED RADIO [F/W UPDATE] [UPDATE SYSTEM] [F/W UP xxxx] [YES]: Starts upgrading the firmware. ; [NO]: Cancels (upgrading is not activated). For details on how to update the firmware, visit . [FACTORY RESET] [YES]: Resets the settings to default (except the stored station). ; [NO]: Cancels. [CLOCK] [TIME SYNC] [ON]: The clock time is automatically set using the Clock Time (CT) data in FM Radio Broadcast Data System signal. ; [OFF]: Cancels.
RADIO Select a stored station Press one of the number buttons (1 to 6). (or) 1 Press . 2 Turn the volume knob to select a preset number, then press the knob. [SSM] [SSM 01–06]/[SSM 07–12]/[SSM 13–18]: Automatically presets up to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select [SSM 07–12]/[SSM 13–18] to store the following 12 stations. [IF BAND] [AUTO]: Increases the tuner selectivity to reduce interference noises from adjacent FM stations.
CD/USB/iPod/ANDROID Start playback The source changes automatically and playback starts. CD Label side Eject disc Selectable source: • KD-T905BTS: CD/USB FRONT/USB REAR/iPod FRONT/iPod REAR/ANDROID FRONT/ANDROID REAR • KD-T900BTS/KD-T805BTS/KD-TD90BTS/KD-T700BT/KD-TD70BT/KD-SR85BT: CD/USB/iPod USB/ANDROID USB input terminal USB USB 2.0 cable*1 (commercially available) To On the faceplate On the remote control Reverse/Fast-forward*3 Press and hold S / T. Press and hold H / I.
CD/USB/iPod/ANDROID Select music drive Select a file from a folder/list While in USB FRONT/USB REAR/USB source, press 5 MODE repeatedly. For iPod, applicable only when [HEAD MODE] is selected. Stored songs in the following drive will be played back. • Selected internal or external memory of a smartphone (Mass Storage Class). • Selected drive of a multiple drive device. 1 Press . 2 Turn the volume knob to select a folder/list, then press the knob.
Pandora® Preparation: Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora. • Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. (Page 4) Create and store a new station . 1 Press 2 Turn the volume knob to select [NEW STATION], then press the knob. 3 Turn the volume knob to select [FROM ARTIST] or [FROM TRACK], then press the knob. A new station is created based on the current song or artist.
iHeartRadio® Preparation: Install the latest version of iHeartAuto application on your device (iPhone/ iPod touch), then create an account and log in to iHeartRadio. • Select [ON] for [IHEART SRC] in [SOURCE SELECT]. (Page 4) Start listening 1 Start up the iHeartAuto application on your device. 2 Connect your device to the USB input terminal. USB input terminal Accessory of the iPod/iPhone* To On the faceplate On the remote control Play back/pause Press the volume knob. Press d.
Spotify Preparation: Install the latest version of the Spotify application on your device (iPhone/ iPod touch), then create an account and log in to Spotify. • Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]. (Page 4) Start listening To On the faceplate Repeat play*3 Press 4 B repeatedly. [ALL REPEAT], [ONE REPEAT]*1, [REPEAT OFF] Random play*3 1 Start up the Spotify application on your device. 2 Connect your device to the USB input terminal. Press 3 A repeatedly *1.
SiriusXM® Radio (for KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS) Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit . Preparation: 1 Connect the optional SiriusXM Vehicle Tuner (commercially available).
SiriusXM® Radio (for KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS) SiriusXM Replay™ While listening to a channel... 1 Press the volume knob. “ ” lights up and the unit memorizes this paused position. 2 Press the volume knob to start Replay. Replay starts from the paused position in step 1. During Replay... Using SiriusXM tuner models later than SXV200: This unit can assign a maximum of 18 SmartFavorites channels. Initially, all preset channels are assigned as SmartFavorites.
SiriusXM® Radio (for KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS) TuneScan™ [CODE SET] 1 2 3 4 5 6 • [LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting. ; [USER DEFINED]: Selects the individual channels the user wants to lock. ; [OFF]: Cancels. [CHANNEL EDIT]*1 1 Turn the volume knob to select a category, then press the knob. 2 Turn the volume knob to select a channel you want to lock, then press the knob. “L” appears in front of the channel number. 3 Press and hold to exit.
BLUETOOTH® Depending on the operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit.
BLUETOOTH® • Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually. • When the battery of the connected Bluetooth device runs low, “Device Name” “LOW BATTERY” appears. • Refer to the instruction manual of the Bluetooth device for more information. BLUETOOTH — Mobile phone Auto Pairing When you connect iPhone/iPod touch to the USB input terminal, pairing request (via Bluetooth) is automatically activated.
BLUETOOTH® The following operations may differ or be unavailable depending on the connected phone. To On the faceplate On the remote control Answer a call Press knob. Press J / K / H / I. Reject a call Press and hold volume knob. or the Press and hold J / K / H / I. End a call Press and hold volume knob. or the Press and hold J / K / H / I. First incoming call... or the volume Improve the voice quality While talking on the phone... 1 Press and hold .
BLUETOOTH® Default: [XX] [RECENT CALL] (Applicable only if the phone supports PBAP.) 1 Press the volume knob to select a name or a phone number. • “<” indicates call received, “>“ indicates call made, “M” indicates call missed. • “NO HISTORY” appears if there is no recorded call history or call number. 2 Press the volume knob to call. [PHONEBOOK] (Applicable only if the phone supports PBAP.) 1 Press 2 J / 1 K to select the desired letter (A to Z, 0 to 9, and OTHERS).
BLUETOOTH® Default: [XX] Settings in memory [BT MODE] Store a contact in memory You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK] or [DIAL NUMBER], then press the knob. 3 Turn the volume knob to select a contact or enter a phone number. If a contact is selected, press the volume knob to show the phone number. 4 Press and hold one of the number buttons (1 to 6).
BLUETOOTH® Bluetooth compatibility check mode You can check the connectivity of the supported profile between the Bluetooth device and the unit. • Make sure there is no Bluetooth device paired. 1 Press and hold . “BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW USING PHONE” “PIN IS 0000” scrolls on the display. 2 Search and select the name of your receiver (“KD-T9 BTS”/ “KD-T8 BTS”/“KD-T7 BT”/“KD-TD9 BTS”/“KD-TD7 BT”/ “KD-SR8 BT”) on the Bluetooth device within 3 minutes.
BLUETOOTH® BLUETOOTH — Audio To On the faceplate Repeat play Press 4 B repeatedly. [TRACK REPEAT], [ALL REPEAT], [REPEAT OFF] Random play While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices. Audio player via Bluetooth 1 Press B SRC repeatedly to select BT AUDIO (or press SOURCE on the remote control). • Pressing enters BT AUDIO directly. 2 Operate the Bluetooth audio player to start playback.
BLUETOOTH® Settings to use JVC Remote application [STATUS] JVC Remote application is designed to control the JVC car receiver’s operations from the iPhone/iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth). Preparation: Install the latest version of JVC Remote application on your device before connecting. For more information, visit . 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the knob.
BLUETOOTH® Internet radio via Bluetooth You can listen to internet radio (Pandora, iHeartRadio and Spotify) on the iPhone/iPod touch/Android device via Bluetooth on this unit. • Make sure the USB input terminal is not connected to any device. Listen to Pandora Preparation: Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. (Page 4) 1 Start up the Pandora application on your device. 2 Connect your device via Bluetooth connection.
AUX AUDIO SETTINGS Preparation: You can listen to music from a portable audio player via the auxiliary input jack. • Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT]. (Page 4) Start listening 1 Connect a portable audio player (commercially available). 3.5 mm (1/8") stereo mini plug with “L” shaped connector (commercially available) Portable audio player 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the knob.
AUDIO SETTINGS [PRO EQ] Adjusts your own sound settings. • The settings are stored to [USER] in [PRESET EQ]. • The settings made may affect the current settings of [EASY EQ]. [62.5HZ] [LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) [BALANCE]*4 [POSITION L15] to [POSITION R15] ([POSITION 00]): Adjusts the left and right speaker output balance.
AUDIO SETTINGS KD-T900BTS/KD-TD90BTS/KD-SR85BT: [SOUND EFFECT] [SPACE ENHANCE] (Not applicable for FM/AM source.) [SMALL]/[MEDIUM]/[LARGE]: Virtually enhances the sound space. ; [OFF]: Cancels. [SND RESPONSE] [LEVEL1]/[LEVEL2]/[LEVEL3]: Virtually makes the sound more realistic. ; [OFF]: Cancels. [SOUND LIFT] [LOW]/[MIDDLE]/[HIGH]: Virtually adjusts the sound position heard from the speakers. ; [OFF]: Cancels.
AUDIO SETTINGS Crossover settings Below are the available setting items for 2-way crossover and 3-way crossover. 2-way crossover setting items [SPEAKER SIZE] [FRONT] [SIZE] [3.5"]/[4"]/[4.75"]/[5"]/[6.5"]/[6.75"]/[7"]/ [4×6]/[5×7]/[6×8]/[6×9]/[7×10] [TWEETER] [SMALL]/[MIDDLE]/[LARGE]/[NONE] (not connected) Caution Select a crossover type according to how the speakers are connected. (Page 40, 41) If you select a wrong type: • The speakers may be damaged.
AUDIO SETTINGS [SUBWOOFER LPF]*2*3 [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/ [90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/ [220HZ]/[250HZ]/[THROUGH] [SW LPF SLOPE] [–06DB]/[–12DB]/[–18DB]/[–24DB] [SW LPF PHASE] [REVERSE] (180°)/ [NORMAL] (0°) [SW LPF GAIN] [MID RANGE] [HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/ [100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]/ [THROUGH] [HPF SLOPE] [–06DB]/[–12DB] [LPF FRQ] [–08DB] to [00DB] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.
AUDIO SETTINGS Digital Time Alignment settings Determining the value for [DISTANCE] and [GAIN] of [DTA SETTINGS] [POSITION] Selects your listening position (reference point). [ALL]: Not compensating ; [FRONT RIGHT]: Front right seat ; [FRONT LEFT]: Front left seat ; [FRONT ALL]: Front seats • [FRONT ALL] is displayed only when [X ' OVER TYPE] is set to [2-WAY]. (Page 25) [DISTANCE]*1 [0FT] to [20.01FT]: Fine adjust the distance to compensate.
DISPLAY SETTINGS Zone identification for brightness settings Default: [XX] [DISPLAY] KD-T905BTS/ KD-T900BTS/ KD-T805BTS/ KD-TD90BTS [DIMMER] Dims the illumination. [OFF]: Dimmer is turned off. Brightness changes to [DAY] setting. [ON]: Dimmer is turned on. Brightness changes to [NIGHT] setting. (See “[BRIGHTNESS]” below.) [DIMMER TIME]: Set the dimmer on and off time. 1 Turn the volume knob to adjust the [ON] time, then press the knob.
DISPLAY SETTINGS [COLOR] (for KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS) [PRESET] [DAY COLOR] [NIGHT COLOR] [COLOR GUIDE] *1 *2 *3 *4 Selects illumination colors for the buttons on different zones separately. 1 Select a zone ([ZONE 1], [ZONE 2], [ALL ZONE]). (See the illustration on page 30.) 2 Select a color for the selected zone. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown.
REFERENCES Playable files • Playable audio file: For disc: MP3 (.mp3), WMA (.wma), AAC (.aac) For USB mass storage class device: MP3 (.mp3), WMA (.wma), AAC (.aac), AAC (.m4a), WAV (.wav), FLAC (.
REFERENCES • Some functions of Spotify cannot be operated from this unit. • For issues using the application, please contact Spotify at . About Bluetooth • Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect to this unit. • This unit may not work with some Bluetooth devices. • Signal conditions vary, depending on the surroundings. Change the display information Each time you press , the display information changes.
REFERENCES Source name Display information: Main (Supplementary) Source name Display information: Main SIRIUS XM Channel number (Status) Channel number (Status) with Music Synchronization Effect*2 Channel name (Status) Artist (Status) Song title (Status) Content information (Status) Category name (Status) Date (Status) back to the beginning CD or USB For CD-DA: Disc title/Artist Disc title/Artist with Music Synchronization Effect* Track title/Artist Playing time Clock back to the beginning BT AUDIO
TROUBLESHOOTING Symptom Radio • Adjust the volume to the optimum level. • Check the cords and connections. “NOT SUPPORT” appears and track skips. Remedy Check whether the track is a playable format. (Page 31, 32) “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “READING” keeps flashing. • Do not use too many hierarchical levels and folders.
TROUBLESHOOTING “NO DEVICE” or “READING” keeps flashing. Playback is intermittent or sound skips. Pandora “CANNOT PLAY” 36 • Reconnect the Android device. • If USB connection does not work, connect the Android device via Bluetooth or through auxiliary input jack. Turn off the power saving mode on the Android device. Pandora • Reconnect the Android device. • Launch any media player application on the Android device and start playback.
TROUBLESHOOTING Remedy Symptom Remedy “CH LOCKED LOCK CODE?” The selected channel is locked. Enter the correct pass code to unlock. (Page 14) No Bluetooth device is detected. • Search from the Bluetooth device again. • Reset the unit. (Page 3) “CHAN UNSUB” The selected channel is unsubscribed. Call 1-866-635-2349 in the U.S.A. or 1-877-438-9677 in Canada to subscribe. (Page 12) Pairing cannot be made. “CH UNAVAIL” The selected channel is unavailable.
INSTALLATION/CONNECTION TROUBLESHOOTING Bluetooth® Symptom Remedy “PLEASE WAIT” The unit is preparing to use the Bluetooth function. If the message does not disappear, turn off and turn on the unit, then connect the device again. “NOT SUPPORT” The connected phone does not support Voice Recognition feature or phonebook transfer. “NO ENTRY”/“NO PAIR” There is no registered device connected/found via Bluetooth. “ERROR” Try the operation again.
INSTALLATION/CONNECTION Part list for installation Installing the unit (in-dash mounting) (A) Faceplate (×1) (B) Trim plate (×1) (C) Mounting sleeve (×1) (D) Wiring harness (×1) Do the required wiring. (Page 40) Hook on the top side Orientate the trim plate as illustrated before fitting. Dashboard of your car (E) Extraction key (×2) Bend the appropriate tabs to hold the sleeve firmly in place.
INSTALLATION/CONNECTION Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Antenna terminal Vehicle dashboard Fuse (10 A) Light blue/yellow Factory wiring harness (vehicle) To the steering wheel remote control adapter Custom wiring harness (separately purchased) Join the same color wires together.
INSTALLATION/CONNECTION Connecting external components KD-T905BTS: USB cable (DC 5 V 1.5 A) (approx. 1 m/3.
SPECIFICATIONS 8.2 dBf (0.71 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.0 μV/75 Ω) Frequency Response (±3 dB) 30 Hz — 15 kHz Signal-to-Noise Ratio (MONO) 64 dB Stereo Separation (1 kHz) 40 dB CD player Usable Sensitivity (S/N = 20 dB) 530 kHz — 1 700 kHz (10 kHz step) 531 kHz — 1 611 kHz (9 kHz step) USB Usable Sensitivity (S/N = 26 dB) AM Frequency Range 42 87.9 MHz — 107.9 MHz (200 kHz step) 87.5 MHz — 108.0 MHz (50 kHz step) 29 dBμ (28.2 μV) USB Standard USB 1.
Audio Bluetooth SPECIFICATIONS Bluetooth 3.0 Operating Voltage 12 V DC car battery Frequency Range 2.402 GHz — 2.480 GHz Installation Size (W × H × D) RF Output Power (E.I.R.P.) +4 dBm (MAX), Power Class 2 182 mm × 53 mm × 156 mm (7-3/16" × 2-1/8" × 6-3/16") Maximum Communication Range Line of sight approx. 10 m (32.8 ft) Net Weight (includes Trimplate, Mounting Sleeve) 1.2 kg (2.7 lbs) Pairing SSP (Secure Simple Pairing) Profile HFP1.
libFLAC Copyright (C) 2000-2009 Josh Coalson Copyright (C) 2011-2013 Xiph.Org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
ENGLISH FRANÇAIS ESPAÑOL KD-T905BTS / KD-T900BTS / KD-T805BTS / KD-TD90BTS / KD-T700BT / KD-TD70BT / KD-SR85BT CD RECEIVER Quick Start Guide RÉCEPTEUR CD Guide de démarrage rapide RECEPTOR CON CD Guía de inicio rápido For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website: Pour les opérations et les informations détaillées, reportez-vous au MANUEL D’INSTRUCTIONS sur le site web suivant: Para obtener más información y detalles sobre las operaciones, consulte el
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Notice This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
SOFTWARE LICENSE AGREEMENT The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software. The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
Article 10 1. 2. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights. Article 11 1. 2. 3. 2. 3.
INSTALLATION/CONNECTION Warning • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit. • To prevent short circuit: – Insulate unconnected wires with vinyl tape. – Be sure to ground this unit to the car’s chassis again after installation.
Installing the unit (without mounting sleeve) 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (commercially available). Wiring connection Antenna terminal Vehicle dashboard Fuse (10 A) Factory wiring harness (vehicle) Use only the specified screws. Using wrong screws might damage the unit. Join the same color wires together.
BEFORE USE BASICS IMPORTANT Faceplate • To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide. • Please keep the Guide in a safe and accessible place for future reference. Volume knob Loading slot KD-T700BT/ Display window KD-TD70BT/ KD-SR85BT Warning USB input terminal Do not operate any function that takes your attention away from safe driving.
GETTING STARTED 3 Set the basic settings 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then 1 Cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES]), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB” 1 Press the volume knob. To return to the previous setting item, press [YES] is selected for the initial setup. 2 Press the volume knob again. “DEMO OFF” appears. .
RADIO Search for a station 1 Press B SRC repeatedly to select FM or AM. 2 Press S / T to search for a station automatically. (or) Press and hold S / T until “M” flashes, then press repeatedly to search for a station manually. Settings in memory You can store up to 18 stations for FM and 6 stations for AM. Store a station While listening to a station.... Press and hold one of the number buttons (1 to 6). (or) 1 Press and hold the volume knob until “PRESET MODE” flashes.
Examples of some well-used settings MENU SETTINGS Subwoofer Level Setting 1 2 3 4 Press and hold to enter menu settings. Turn the volume knob to select an item, then press the knob. Repeat step 2 until the desired item is selected/activated. Press to exit. To return to the previous setting item, press . • Refer to the INSTRUCTION MANUAL on the following website for the detailed explanation of each item: • The availability of each item vary depending on the model.
8 Press to exit the setting menu. Note: For KD-T900BTS/KD-TD90BTS/KD-T700BT/KD-TD70BT/KD-SR85BT, you need to set [SPK/PRE OUT] to [REAR/SUB.W] or [SUB.W/SUB.W] before you can make the subwoofer level settings. Illumination Color Setting For KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS, you can set your preferred illumination color for each zone. 5 Turn the volume knob to choose a color, then press the knob.
(B) “[Device Name]” “VOL – YES” “BACK – NO” Press the volume knob to start pairing. • If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device. • If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. BLUETOOTH® Depending on the operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit. Connect the microphone Connect the supplied microphone to the microphone input jack on the rear panel.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
WHEN IT IS NOT REQUIRED TO DETACH THE FRONT CONTRO L PANEL FROM THE MAIN UNIT, USE THE PROVIDED SCREW TO ATTACH THE CONTROL PANEL TO THE MAIN UNIT.
U.S.A. JVCKENWOOD USA Cor oration TO OUR VALUED CUSTOMER THANK YOU FOR PURCHASING THIS JVC PRODUCT. WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE. JVC liMITED WARRANTY ONLY FOR PRODUCT PURCHASED IN U.S.A. JVCKENWOOD USA Corporation warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL RETAIL PURC HASER to be FREE FROM DEFECTIVE MATER IALS AND WORKMANSHIP fro m the date of original purchase for the period shown below.
CANADA .JVC JVCKENWOOD CANADA INC. Warranty applies only to PRO!~~s~i!~~;Canada GARANTIE by JVCKENWOOD CANADA INC. La garantls' applique seulement aux PRODUITSdistrlbues au Canada par JVCKENWOOD CANADA INC. JVCKENWOOD CANADA INC. (hereafter called "JVC") gives the following express warranty for each new JVC product distributed in Canada by JVC and sold by an authorized JVC dealer.