ENGLISH FRANÇAIS ESPAÑOL KD-T915BTS / KD-T910BTS / KD-TD91BTS / KD-T91MBS/ KD-T711BT / KD-T710BT / KD-TD71BT / KD-SR86BT CD RECEIVER INSTRUCTION MANUAL RÉCEPTEUR CD MANUEL D’INSTRUCTIONS RECEPTOR CON CD MANUAL DE INSTRUCCIONES For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No. B5A-3092-00 [K] JS_JVC_KD_T915BTS_K_C.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Important Notice concerning the Software -CMP -jansson The MIT License (MIT) Copyright (c) 2014 Charles Gunyon Copyright (c) 2009-2012 Petri Lehtinen
Contents Before Use ................................................................................................. 3 References .............................................................................................. 37 Basics ......................................................................................................... 4 Maintenance Getting Started ........................................................................................
Before Use IMPORTANT • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings and Cautions in this manual. • Please keep the manual in a safe and accessible place for future reference. WARNING • Do not operate any function that takes your attention away from safe driving. • Do not ingest the battery, Chemical Burn Hazard. The remote control supplied with this product contains a coin/button cell battery.
Basics Faceplate KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS: Volume knob Loading slot Attach Display window* Detach KD-T915BTS: USB cable from the rear of the unit Detach button How to reset KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT: Reset the unit within 5 seconds after detaching the faceplate. KD-T711BT: * Only for illustration purpose. To On the faceplate Turn on the power Press B SRC. • Press and hold to turn off the power. Adjust the volume Turn the volume knob.
Getting Started Basics Remote control (RM-RK52) (supplied for KD-T711BT) • For KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS/KD-T710BT/ KD-TD71BT: This unit can be remotely controlled with an optionally purchased remote control. • For KD-SR86BT: Remote control functions are not available. Remote sensor (Do not expose to bright sunlight.
Getting Started 9 Press to exit. To return to the previous setting item, press 3 [USER S.REMO] (For KD-T711BT) See page 36 for details. . [F/W UPDATE] Set the basic settings [UPDATE SYSTEM] . 1 Press and hold 2 Turn the volume knob to select an item (see the following table), then [F/W UP xxxx] press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit. To return to the previous setting item, press [FACTORY RESET] .
Radio Select a stored station Press one of the number buttons (1 to 6). (or) 1 Press . 2 Turn the volume knob to select a preset number, then press the knob. Other settings Search for a station 1 Press B SRC repeatedly to select FM or AM. 2 Press S / T (or press H / I on the remote control) to search for a station automatically. (or) Press and hold S / T (or press and hold H / I on the remote control) until “M” flashes, then press repeatedly to search for a station manually. .
Radio [SSM] [SSM 01–06]/[SSM 07–12]/[SSM 13–18]: Automatically presets up to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select [SSM 07–12]/[SSM 13–18] to store the following 12 stations. [IF BAND] [AUTO]: Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.) ; [WIDE]: Subjects to interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.
Radio PTY code for FM Radio Data System [NEWS], [AFFAIRS], [INFO], [SPORT], [EDUCATE], [DRAMA], [CULTURE], [SCIENCE], [VARIED], [POP M] (music), [ROCK M] (music), [EASY M] (music), [LIGHT M] (music), [CLASSICS], [OTHER M] (music), [WEATHER], [FINANCE], [CHILDREN], [SOCIAL], [RELIGION], [PHONE IN], [TRAVEL], [LEISURE], [JAZZ], [COUNTRY], [NATION M] (music), [OLDIES], [FOLK M] (music), [DOCUMENT] CD/USB/iPod Insert a disc Eject disc Label side The source changes to CD automatically and playback starts.
CD/USB/iPod Connect an iPod/iPhone USB input terminal Accessory of the iPod/iPhone* iPod/ iPhone To On the faceplate On the remote control Reverse/ Fast-forward Press and hold S / T. Press and hold H / I. Select a track/file Press S / T. Press H / I. Select a folder*1 Press 2 J / 1 K. Press J / K. Repeat play*2 Press 4 B repeatedly. and/or [TRACK REPEAT]/[ALL REPEAT]: Audio CD KD-T915BTS: You can also connect to the USB cable from the rear of the unit (USB input terminal).
CD/USB/iPod Quick search (applicable only for CD source and USB FRONT/USB REAR/USB Select music drive While in USB FRONT/USB REAR/USB source, press 5 MODE repeatedly. Stored songs in the following drive will be played back. • Selected internal or external memory of a smartphone (Mass Storage Class). • Selected drive of a multiple drive device. Select control mode While in iPod FRONT/iPod REAR/iPod USB source (or iPod BT source), press 5 MODE repeatedly. [HEAD MODE]: Control iPod/iPhone from this unit.
AUX Pandora® (except for KD-T711BT) You can listen to music from a portable audio player via the auxiliary input jack. You can listen to Pandora on iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth). Preparation: Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT]. (Page 6) Preparation: • Install the latest version of the Pandora application on your device (iPhone/ iPod touch or Android device), then create an account and log in to Pandora.
Pandora® (except for KD-T711BT) To On the faceplate On the remote control Play back/pause Press the volume knob. Press d. Skip a track Press T. Press I. Select thumbs up or thumbs down* Press 2 J / 1 K. Press J / K. Bookmark current song information Press and hold the volume knob. “BOOKMARKED” appears and the information is stored to your device. • The bookmark is available on your Pandora account but not on this unit. * If thumbs down is selected, the current track is skipped.
Spotify You can listen to Spotify on iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth). Preparation: • Install the latest version of the Spotify application on your device (iPhone/ iPod touch or Android device), then create an account and log in to Spotify. • Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]. (Page 6) Start listening Accessory of the iPhone/iPod touch* On the faceplate Play back/pause Press the volume knob. Press d.
SiriusXM® Radio Spotify (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) Search for a song or station . 1 Press 2 Turn the volume knob to select a list type, then press the knob. The list types displayed differ depending on the information sent from Spotify. 3 Turn the volume knob to select the desired song or station, then press the knob. You can browse through the list quickly by turning the volume knob quickly.
SiriusXM® Radio (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) Select a stored channel Start listening 1 Press B SRC repeatedly to select SIRIUS XM. 2 Press . “ ” indicator lights up. 3 Turn the volume knob to select a CATEGORY, then press the knob. 4 Turn the volume knob to select a category from the list, then press the knob. If “ALL CHANNELS” is selected, all the available channels will be shown. 5 Turn the volume knob to select a channel, then press the knob.
SiriusXM® Radio (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) SmartFavorites and TuneStart™ User preset channels are initially assigned as the SmartFavorites channels. SmartFavorite channel is available with SXV200 or later SiriusXM tuner models. The SiriusXM Vehicle Tuner automatically buffers the broadcast audio content of the SmartFavorites channels in the background. Using SXV200: This unit can assign a maximum of 6 SmartFavorites channels.
SiriusXM® Radio (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) TuneScan™ [CODE SET] 1 2 3 4 5 6 • [LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting. ; [USER DEFINED]: Selects the individual channels the user wants to lock. ; [OFF]: Cancels. [CHANNEL EDIT]*1 1 Turn the volume knob to select a category, then press the knob. 2 Turn the volume knob to select a channel you want to lock, then press the knob. “L” appears in front of the channel number. 3 Press and hold to exit.
Using Other Applications JVC Remote application Default: [XX] You can control the JVC car receiver from iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth) using JVC Remote application. • For more information, visit . [REMOTE APP] [SELECT] [YES]: Selects iPhone/iPod touch to use the application via Bluetooth or connected via USB input terminal. ; [NO]: Cancels.
Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit. • Be sure to turn on the Bluetooth function of the device to make the following operations. • Signal conditions vary depending on the surroundings.
Bluetooth® • KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT, “ indicator(s) light(s) up. ” and/or “ ” • This unit supports Secure Simple Pairing (SSP). • Up to five devices can be registered (paired) in total. • Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device, see [DEVICE DELETE] on page 24. • A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.
Bluetooth® The following operations may differ or be unavailable depending on the connected phone. To On the faceplate On the remote control Improve the voice quality First incoming call... Answer a call Press or the volume knob. Press J / K / H / I. Reject a call Press and hold or the volume knob. Press and hold J / K / H / I. Press and hold or the volume knob. Press and hold J / K / H / I. End a call *1 This adjustment will not affect the volume of the other sources.
Bluetooth® Default: [XX] [RECENT CALL] (Applicable only if the phone supports PBAP.) 1 Press the volume knob to select a name or a phone number. • “<” indicates call received, “>“ indicates call made, “M” indicates call missed. • “NO HISTORY” appears if there is no recorded call history or call number. 2 Press the volume knob to call. [PHONEBOOK] (Applicable only if the phone supports PBAP.) 1 Press 2 J / 1 K to select the desired letter (A to Z, 0 to 9, and OTHERS).
Bluetooth® Default: [XX] Store a contact in memory You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK] or [BT MODE] [PHONE SELECT] [AUDIO SELECT] [DIAL NUMBER], then press the knob. 3 Turn the volume knob to select a contact or enter a phone number. If a contact is selected, press the volume knob to show the phone number. 4 Press and hold one of the number buttons (1 to 6).
Bluetooth® Bluetooth compatibility check mode You can check the connectivity of the supported profile between the Bluetooth device and the unit. • Make sure there is no Bluetooth device paired. 1 Press and hold . “BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW USING PHONE” “PIN IS 0000” scrolls on the display. 2 Search and select the name of your receiver (“KD-T915BTS”/ “KD-T910BTS”/“KD-TD91BTS”/“KD-T91MBS”/“KD-T711BT”/ “KD-T710BT”/“KD-TD71BT”/“KD-SR86BT”) on the Bluetooth device within 3 minutes.
Bluetooth® Bluetooth — Audio To On the faceplate [TRACK REPEAT], [ALL REPEAT], [GROUP REPEAT]*1, [REPEAT OFF] [GROUP RANDOM]*1, [ALL RANDOM], [RANDOM OFF] Listen to the audio player via Bluetooth 1 Press B SRC repeatedly to select BT AUDIO (or press SOURCE on the remote control). • For KD-T711BT: Pressing enters BT AUDIO directly. 2 Operate the audio player via Bluetooth to start playback. To On the faceplate On the remote control Play back/pause Press the volume knob. Press d.
AMAZON ALEXA (except for KD-T711BT) Alexa is the cloud-based voice service developed by Amazon. You can ask Alexa to play music, get weather reports, traffic information, control smart home devices, shop on Amazon, search the internet, set reminders and more. Preparation: • Create an account at , or use the Alexa mobile application. • After installing the latest version of the Alexa mobile application on your device, log in using those credentials.
AMAZON ALEXA (except for KD-T711BT) Start listening While in Alexa idle state... 1 Press Basic operations on the unit to activate Alexa. The display shows: “LISTENING...”. 2 Communicate with Alexa via the connected microphone. (Page 20) 3 During music playback in ALEXA source, you can perform the following operations: Once Alexa connection is established... To On the faceplate 1 Press Play back/pause Press the volume knob. Press d. Reverse skip/ Forward skip Press S / T. Press H / I.
Audio Settings [PRO EQ] Adjusts your own sound settings for each source. • The settings are stored to [USER] in [PRESET EQ]. • The settings made may affect the current settings of [EASY EQ]. [62.5HZ] [LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the knob.
Audio Settings [FADER] (Not applicable when 3-way crossover is selected.) [POSITION R15] to [POSITION F15] ([POSITION 00]): Adjusts the front and rear speaker output balance. [BALANCE]*4 [POSITION L15] to [POSITION R15] ([POSITION 00]): Adjusts the left and right speaker output balance. [VOLUME ADJUST] [LEVEL –15] to [LEVEL +06] ([LEVEL 00]): Presets the initial volume level of each source by comparing to the FM volume levels. (Before adjustment, select the source you want to adjust.
Audio Settings KD-T711BT/KD-T710BT/KD-TD71BT: Speaker output settings [SPK/PRE OUT] (Applicable only if [X ' OVER TYPE ] is set to [2-WAY]) (page 30) Setting on [SPK/PRE OUT] Select the output setting for the speakers [SPK/PRE OUT], based on the speaker connection method. [REAR/REAR] Audio signal through lineout terminal REAR/SW Rear speakers output [REAR/SUB.W] (default) Subwoofer output Connection via lineout terminals [SUB.W/SUB.
Audio Settings Crossover settings Below are the available setting items for 2-way crossover and 3-way crossover. 2-way crossover setting items [SPEAKER SIZE] [FRONT] [SIZE] [3.5"]/[4"]/[4.75"]/[5"]/[6.5"]/[6.75"]/[7"]/ [4×6]/[5×7]/[6×8]/[6×9]/[7×10] [TWEETER] [SMALL]/[MIDDLE]/[LARGE]/[NONE] (not connected) CAUTION Select a crossover type according to how the speakers are connected. (Page 46, 47) If you select a wrong type: • The speakers may be damaged.
Audio Settings [SUBWOOFER LPF]*2*3 [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/ [90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/ [220HZ]/[250HZ]/[THROUGH] [SW LPF SLOPE] [–06DB]/[–12DB]/[–18DB]/[–24DB] [SW LPF PHASE] [REVERSE] (180°)/ [NORMAL] (0°) [SW LPF GAIN] [MID RANGE] [HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/ [100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]/ [THROUGH] [HPF SLOPE] [–06DB]/[–12DB] [LPF FRQ] [–08DB] to [00DB] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.
Audio Settings Digital Time Alignment settings Determining the delay time automatically If you specify the distance from the currently set listening position to every speaker, the delay time will be automatically calculated. 1 Set [POSITION] and determine the listening position as the reference point (the reference point for [FRONT ALL] will be the center between the right and left in the front seats). 2 Measure the distances from the reference point to the speakers.
Display Settings Zone identification for brightness settings 4 Press KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS: To return to the previous setting item, press to exit. . Default: [XX] [DISPLAY] [DIMMER] Dims the illumination. [OFF]: Dimmer is turned off. Brightness changes to [DAY] setting. [ON]: Dimmer is turned on. Brightness changes to [NIGHT] setting. (See the following “[BRIGHTNESS]” settings.) [DIMMER TIME]: Set the time to turn on dimmer and to turn off dimmer.
Display Settings [COLOR] (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) [PRESET] [DAY COLOR] [NIGHT COLOR] [COLOR GUIDE] Selects illumination colors for the buttons on different zones separately. 1 Select a zone ([ZONE 1], [ZONE 2], [ALL ZONE]). (See the illustration on page 35.) 2 Select a color for the selected zone. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown. • [COLOR FLOW01] to [COLOR FLOW03]: Color changes at different speeds.
Learning Steering Remote Control (for KD-T711BT) 6 Press and hold any control keys on your steering remote control which you want to assign. A list of key functions will appear on the display. [NONE] (default)/[MUTE]/[SEEK UP]/[SEEK DOWN]/[VOL UP]/[VOL DOWN]/[MODE]/ [ON HOOK]/[OFF HOOK]/[VOICE]/[ENTER] 7 Turn the volume knob to select a function to assign, then press the knob. The selected key function is assigned to the steering remote control key you have selected in step 6.
References Playable files • Playable audio file: For disc: MP3 (.mp3), WMA (.wma), AAC (.aac) For USB mass storage class device: MP3 (.mp3), WMA (.wma), AAC (.aac), AAC (.m4a), WAV (.wav), FLAC (.
References Change the display information Source name Display information: Main (Supplementary) For MP3/WMA/AAC/WAV/FLAC files: Song title (Artist) Song title (Artist) with Music Synchronization Effect*2 Song title (Album title) Song title (Date) File name (Folder name) File name (Date) Playing time (Date) back to the beginning Each time you press , the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO NAME”, or other information (eg.
References KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT: Main display Clock display Source name Display information: Main FM or AM Frequency Frequency with Music Synchronization Effect* back to the beginning Date For FM Radio Broadcast Data System/FM Radio Data System stations only: Station name/Program type Station name/Program type with Music Synchronization Effect* Radio text Radio text+ Radio text+ song title/Radio text+ artist Frequency Date back to the beginning CD or USB Source name Display informa
Troubleshooting General Sound cannot be heard. “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “PROTECTING SEND SERVICE” appears. Send the unit to the nearest service center. Source cannot be selected. Check the [SOURCE SELECT] setting. (Page 6) The unit does not work at all. Reset the unit. (Page 4) Radio Correct characters are not displayed.
Troubleshooting 42 Remedy “LOADING” appears when you enter search mode by pressing . This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later. “NO DISC” Insert a playable disc into the loading slot. “NO DEVICE” Connect a device (USB/iPod/iPhone), and change the source to USB/iPod/iPhone again. “MEMORY FULL” You have reached the maximum storage limit of your iPod/iPhone. “ADD ERROR” New station creation is unsuccessful.
Troubleshooting Your subscription is updated. Press the volume knob to continue. “CODE ERROR” Make sure you have entered the correct pass code. (Page 18) “NO CONTENT” There is insufficient content to start TuneScan. “SCAN CANCEL” Bluetooth® Remedy “SUBSCRIPTION UPDATED – PRESS ENTER TO CONTINUE.” • Search from the Bluetooth device again. • Reset the unit. (Page 4) Bluetooth pairing cannot be made. • Make sure you have entered the same PIN code to both the unit and Bluetooth device.
Installation/Connection Troubleshooting AMAZON ALEXA Symptom Remedy No response from Alexa after the voice input. Amazon cloud was unable to analyze the voice input. Wrong response from Alexa. Alexa misunderstood what was said or did not catch the entire request or sentence spoken. Please try again. (Page 28) “DISCONNECTED” Be sure to connect your smartphone to the unit via Bluetooth. (Page 20) Not able to connect or reconnect to Alexa mobile application.
Installation/Connection Part list for installation Installing the unit (in-dash mounting) (A) Faceplate (×1) (B) Trim plate (×1) (C) Mounting sleeve (×1) (D) Wiring harness (×1) Do the required wiring. (Page 46) Hook on the top side Orientate the trim plate as illustrated before fitting. Dashboard of your car (E) Extraction key (×2) Bend the appropriate tabs to hold the sleeve firmly in place.
Installation/Connection Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Antenna terminal Vehicle dashboard Fuse (10 A) Light blue/yellow Factory wiring harness (vehicle) To the steering wheel remote control adapter Custom wiring harness (separately purchased) Join the same color wires together.
Installation/Connection Connect external components Connect external amplifiers via output terminals Signal cord (not supplied) JVC Amplifier* Output terminals Remote wire (not supplied) No Part 1 For KD-T915BTS: USB cable (DC 5 V 1.5 A) (approx. 1 m/3.3 feet) To remote lead (blue/white) of the wiring harness. (Page 46) 2 For KD-T711BT: Learning steering remote (page 36) 3 Output terminals (See “Connect external amplifiers via output terminals”.
Specifications 8.2 dBf (0.71 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.0 μV/75 Ω) Frequency Response (±3 dB) 30 Hz — 15 kHz Signal-to-Noise Ratio (MONO) 64 dB Stereo Separation (1 kHz) 40 dB CD player Usable Sensitivity (S/N = 20 dB) 530 kHz — 1 700 kHz (10 kHz step) 531 kHz — 1 611 kHz (9 kHz step) USB Usable Sensitivity (S/N = 26 dB) AM Frequency Range 48 87.9 MHz — 107.9 MHz (200 kHz step) 87.5 MHz — 108.0 MHz (50 kHz step) 29 dBμ (28.2 μV) USB Standard USB 1.
Audio Version Bluetooth V4.2 Operating Voltage 12 V DC car battery Frequency Range 2.402 GHz — 2.480 GHz Installation Size (W × H × D) 182 mm × 53 mm × 156 mm (7-3/16" × 2-1/8" × 6-3/16") Net Weight (includes Trimplate, Mounting Sleeve) KD-T915BTS: 1.3 kg (2.9 lbs) RF Output Power (E.I.R.P.) +4 dBm (MAX), Power Class 2 Maximum Communication Range Line of sight approx. 10 m (32.8 ft) Pairing SSP (Secure Simple Pairing) Profile HFP1.7.
libFLAC Copyright (C) 2000-2009 Josh Coalson Copyright (C) 2011-2013 Xiph.Org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
ENGLISH FRANÇAIS ESPAÑOL KD-T915BTS / KD-T910BTS / KD-TD91BTS / KD-T91MBS / KD-T711BT / KD-T710BT / KD-TD71BT / KD-SR86BT CD RECEIVER Quick Start Guide RÉCEPTEUR CD Guide de démarrage rapide RECEPTOR CON CD Guía de inicio rápido For detailed operations and information, refer to the INSTRUCTION MANUAL on the following website: Pour les opérations et les informations détaillées, reportez-vous au MANUEL D’INSTRUCTIONS sur le site web suivant: Para obtener más información y detalles sobre las operaciones,
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Important Notice concerning the Software -CMP -jansson The MIT License (MIT) Copyright (c) 2014 Charles Gunyon Copyright (c) 2009-2012 Petri Lehtinen
Installation/Connection This section is for the professional installer. For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer. WARNING • The unit can only be used with a 12 V DC power supply, negative ground. • Disconnect the battery’s negative terminal before wiring and mounting. • Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
Installing the unit (without mounting sleeve) 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (commercially available). Wiring connection Antenna terminal Vehicle dashboard Fuse (10 A) Factory wiring harness (vehicle) Use only the specified screws. Using wrong screws might damage the unit. Join the same color wires together.
Before Use Basics (on faceplate) IMPORTANT *1 Only for illustration purpose. • To ensure proper use, please read through this Guide before using this product. It is especially important that you read and observe Warnings and Cautions in this Guide. • Please keep the Guide in a safe and accessible place for future reference.
Getting Started 3 Set the basic settings 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then 1 Cancel the demonstration When you turn on the power for the first time (or [FACTORY RESET] is set to [YES]), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB” 1 Press the volume knob. press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.
Radio Search for a station 1 Press B SRC repeatedly to select FM or AM. 2 Press S / T to search for a station automatically. (or) Press and hold S / T until “M” flashes, then press repeatedly to search for a station manually. Settings in memory You can store up to 18 stations for FM and 6 stations for AM. Store a station While listening to a station.... Press and hold one of the number buttons (1 to 6). (or) 1 Press and hold the volume knob until “PRESET MODE” flashes.
Menu Settings Examples of some well-used settings 1 2 3 4 1 Press and hold Subwoofer Level Setting Press and hold to enter menu settings. Turn the volume knob to select an item, then press the knob. Repeat step 2 until the desired item is selected/activated. Press to exit. To return to the previous setting item, press . • Refer to the INSTRUCTION MANUAL on the following website for the detailed explanation of each item:
8 Press to exit the setting menu. Note: For KD-T910BTS/KD-TD91BTS/KD-T711BT/KD-T710BT/KD-TD71BT/ KD-SR86BT, you need to set [SPK/PRE OUT] to [REAR/SUB.W] or [SUB.W/SUB.W] before you can make the subwoofer level settings. Illumination Color Setting For KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS, you can set your preferred illumination color for each zone. 5 Turn the volume knob to choose a color, then press the knob.
(B) “[Device Name]” “VOL – YES” “BACK – NO” Press the volume knob to start pairing. • If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device. • If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
WHEN IT IS NOT REQUIRED TO DETACH THE FRONT CONTROL PANEL FROM THE MAIN UNIT, USE THE PROVIDED SCREWTO ATTACHTHECONTROLPANELTO THE MAIN UNIT.
JVCKENWOOD USA Cor oration U.S.A. TO OUR VALUED CUSTOMER THANK YOU FOR PURCHASING THIS JVC PRODUCT. WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE. JVC LIMITED WARRANTY ONLY FOR PRODUCT PURCHASED IN U.S.A. JVCKENWOOD USA Corporation warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL RETAIL PURCHASER to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original purchase for the period shown below.
CANADA Jvc JVCKENWOOD CANADA INC. GARANTIE WARRANTY La garantls' applique seulement aux PRODUITS distrlbues au Canada par JVCKENWOOD CANADA INC. Warranty applies only to PRODUCT distributed in Canada by JVCKENWOOD CANADA INC. JVCKENWOOD CANADA INC. (hereafter called "JVC") gives the following express warranty for each new JVC product distributed in Canada by JVC and sold by an authorized JVC dealer.