FRANÇAIS ESPAÑOL ENGLISH DVD RECEIVER WITH MONITOR RECEPTOR DVD CON MONITOR RECEPTEUR DVD ET MONITEUR KD-AV7000 MAIN ATT SUB ZOOM DUAL AVOUT VOL ASPECT MENU TOPMENU OK RETURN TUNER DISC AV 1 2 4 5 6 7 8 9 11/0 12/+10 GUI SET UP Detachable 10 3 VOLUME • This unit is equipped with the display demonstration. To cancel it, see page 14. • Esta unidad está equipada con demostración en la pantalla. Para cancelarla, consulte la página 14.
ENGLISH Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. INFORMATION (For U.S.A.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CAUTIONS on the monitor • DO NOT install any unit in locations where; – it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident. – it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident. – it may obstruct visibility. • DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident. • The driver must not watch the monitor while driving.
ENGLISH Contents How to reset your unit ..................................... 2 Important! (How to read this manual) ............. 3 Surround Mode Operations ........................ 35 Introducing surround/DSP mode ................... 36 Turning on and off the surround/DSP mode .... 37 Introduction—Playable Discs ....................... 5 Quick Guide—How to Use the Controls ...... 6 Remote controller ............................................ 6 Main unit (front) .......................................
Discs you can play You can play back the following discs on this unit: • DVD Video: whose video format is NTSC and whose region code is “1.” –DVD-Rs and DVD-RWs recorded in the DVD-Video format can also be played (see page 69). • Video CD (VCD)/Audio CD • MP3: CD-Rs or CD-RWs including MP3 files with the file extension code . They must be recorded in the format compliant with ISO 9660 Level 1, ISO 9660 Level 2, Romeo, and Joliet.
ENGLISH Quick Guide—How to Use the Controls ○○○○○○○○○ Remote controller General operations Buttons ATT To do: Turn on the main unit. Turn off the main unit. Attenuate sounds. MAIN ATT SUB TUNER ZOOM Select “DISC” and “CD-CH.” DUAL AV Select external components: TV = AV1 = AV2 = AVOUT VOL VOLUME MAIN SUB ASPECT MENU TOPMENU Adjust the volume. Set the main or suboperation for Dual Mode. *1 ZOOM Turn on/off Dual Mode. DUAL OK RETURN TUNER DISC AV 1 2 3 GUI Select “TUNER.
Buttons Buttons To do: Select the band. TUNER To do: Return to the previous screen while operating the disc menu. RETURN Start Auto Search. 1 2 3 4 5 6 Start Manual Search. 1 2 Change preset numbers. 4 5 6 7 8 9 10 11/0 12/+10 Select preset numbers directly. 3 Select title/chapter/track number. *3 CD changer operations Disc operations Buttons ENGLISH Disc operations—continued Tuner operations Buttons To do: To do: Select folders. *2 Play. Select tracks. Pause. Search.
ENGLISH ○○○○○○○○○○○○○○○○○○ Main unit (front) Display CD changer operations General operations Buttons Buttons To do: To do: Turn on the main unit. Select tracks. Turn off the main unit. Search. Attenuate sounds. then Change the sources. Adjust the volume. Change the display information. (once): Display “DISC” = select discs. (twice): Display “FOLDER” = select folders.*1 TV tuner operations Buttons Detach the control panel. To do: Start Auto Search. Start Manual Search.
WARNINGS on the battery: 1 (back side) 2 With the + side facing upwards Lithium coin battery (CR2025) ENGLISH Preparation (Remote Controller—RM-RK220) • Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. • Do not recharge, short, disassemble, or heat the battery or dispose of it in a fire. These behaviors may cause the battery to be overheated, crack or fire. • Do not leave the battery with other metallic materials.
ENGLISH Operation Methods You can operate this unit using three types of operation methods. • This instruction manual explains the operations mainly using the Touch Panel Icons shown on the monitor. • Using the Touch Panel Icons directly (See “BLIND CONTROL” on page 46.) Press the Touch Panel Icons with your finger directly (if you wear a glove, take it off). Examples: The following is just an example. On the actual monitor screen, the playback picture is shown (while video source is played back).
ENGLISH • Using the Graphic User Interface (GUI) from the remote controller You can use the Graphic User Interface in the same way as you touch the panel icons. Examples: 2 1 3 GUI OK OK SET UP Display GUI on the monitor (the cursor—yellow frame— appears around the currently selected icon). • While one of the video sources is selected, the GUI function turns on and off at a press of the button. Move the cursor to an icon you want. Confirm.
ENGLISH Basic Operations CAUTION on the monitor : Do not open or close the monitor by hand. Do not apply any force to the monitor while it is moving. Such a behavior may damage the monitor loading mechanism. For turning on the power, use the buttons on the main unit and the remote controller. 3 Adjust the volume To change the monitor angle: Hold 1 Turn on the power 2 “WAITING” 1 scrolls on the display of the main unit (and the monitor comes out *).
You can also set the clock system to 24 hours or 12 hours. 1 Exit While playing any source... ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○5 Setting the clock To display the clock time: On the main unit When the unit is turned off, the clock time is displayed on the display of the main unit for a while. • If the touch panel icons are not shown on the monitor, touch the center portion of the monitor screen. 2 3 *1 *2 *1 When the unit is turned on...
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ Changing ○ ○ ○the ○graphic ○ ○screen○ ○ ○ Changing the source 1 While playing any source... You can select one of eight graphics in the picture view window. • See page 74 for each graphic screen. When shipped from the factory, display demonstration has been activated, and starts automatically when no operations are done for about 30 seconds (except while playing a DVD/ VCD). To cancel it, select one of the graphic screen. 2 1 2 While playing any source... Ex.
You can display the level meter on the graphic screen, by selecting from four preset patterns. • While viewing the playback picture or display demonstration, you cannot show the level meter. 1 While playing any source... Ex. While listening to FM broadcast. 2 The following level meters are displayed in sequence.
ENGLISH Radio Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current band/Preset no. Station frequency FM reception mode Search mode Sound mode (see page 39) Surround/DSP mode (see page 36) Volume level appears when adjusted. Not available for AM. Available only after pressing “M” (next to this icon). See page 53. See page 14. See page 14. See page 15. See page 39. See pages 43 – 52. Back to the beginning 16 16-19_KD-AV7000[J]f.
• To tune in to a station using Preset Search, first store your favorite stations into memory (6 stations for each band: see page 18). 3 Select Search Mode ENGLISH Listening to the Radio 1 Select the Tuner AUTO: To start Auto Search. MANUAL: To start Manual Search. PRESET: then To select preset station numbers (only possible after storing stations in memory). 4 Tune in to a station 2 Select the band (FM/AM) • For Auto Search, press either icon once. “Auto Search” begins.
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○2 Storing stations in memory You can preset 6 stations for each band. then FM station automatic presetting—SSM (Strong-station Sequential Memory) • This functions only for FM bands. 1 Select the FM band (FM1 – FM3) you want to store FM stations into. Select “MANUAL” (or “AUTO”). 3 4 2 Tune in to a station. Store the station into a preset number. Start SSM. then then Preset station information will be displayed.
1 2 To store a station using the preset list 1 Select the band (FM1 – FM3, and AM) you want to store a station into. 2 Tune into a station. ENGLISH To tune in to a preset station • See also “Listening to the Radio” on page 17. then Select “MANUAL” (or “AUTO”). ○○○○○○○○○3 Displaying the preset list You can store and select the preset stations using the preset list on the monitor screen. To select a preset station using the preset list 4 Store the station into a preset number.
ENGLISH DVD/VCD Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) PBC indicator (for VCD; see page 25) Current track no. (for VCD) Current title/chapter no. (for DVD) Play time information (see page 30) Audio signal format Playback mode (see page 30) Sound mode (see page 39) Surround/DSP mode (see page 36) Playback picture will be shown in the picture view window. Input signal channels are indicated a few second after detected. (See page 69.
ENGLISH CD/MP3 Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current track no. (for CD) Current folder/track no. (for MP3) Play time information (see page 30) Audio signal format (only for DTS CD) Playback mode (see page 30) Sound mode (see page 39) Surround/DSP mode (see page 36) Disc text/ID3 tag information area Only for MP3 (see page 22) Playback buttons (see page 22) CD/CD Text MP3 Only for CD: See page 53. * See page 14. See page 14. See page 15. See page 39.
ENGLISH Basic Disc Operations Before performing any operations, observe the following... • For DVD playback, change the Setup Menu setting (see page 43). • If “ ” appears on the monitor, the disc cannot accept the operation you have tried. – In some cases, “ ” is not display, but operations will not be accepted. 1 Insert a disc 3 Operate the disc : Selects the folder (only for MP3). : Stops (see “Stopping play” on page 69). • VCD/CD/MP3 playback will continue endlessly until you stop it.
DVD To fast-forward or reverse the chapter or track, press ¡ or 1 on the remote controller while playing a disc. Each time you press the button, the search speed changes as follows: VCD with PBC VCD with/without PBC ENGLISH The following marks used in this manual indicate the playable discs. x2 \ x5 \ x10 \ x20 \ x60* To resume normal speed, press 3. CD MP3 All playable discs On-screen guide icons During play, the following guide icons may appear for a while on the monitor.
ENGLISH ○ ○ ○disc○ejection ○○○○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Prohibiting Changing the aspect ratio You can change the aspect ratio of the playback pictures. • This function is only possible using the buttons on the main unit or on the remote controller. • Aspect ratio cannot be changed while the GUI operation mode is activated. On the remote controller On the main unit You can lock a disc in the loading slot. While playing any source...
Menu-driven playback is possible while playing back a DVD with menu-driven features or a VCD with the PlayBack Control (PBC) function. While playing a DVD: DVD discs generally have their own menus or title lists. A title list (TOP MENU) usually contains titles of movies and songs recorded. On the other hand, a menu (MENU) usually contains various information about the disc and playback selections. 1 While playing a VCD: The PBC function allows you to operate the VCD using menus.
ENGLISH When using the number buttons on the remote controller • To select number 5, press 5. • To select number 10, press 10. • To select number 23, press +10, +10, then 3. To cancel the PBC playback You can cancel the menu-driven operations (PBC function) using the remote controller. ○○○○○○○○○ Zooming in You can zoom into a particular portion of the picture. • This function is only possible using the remote controller. 1 1 Press 7 to stop playback. 2 Press number buttons to select a track.
While playing a chapter containing subtitles in different languages, you can select the subtitle language to display on the monitor. • You can also select the subtitle language using SETUP menu (see page 44). For DVD: While playing a chapter containing audio languages, you can select the language to listen to. • You can also select the audio language using SETUP menu (see page 44). 1 For VCD: While playing a track, you can select the audio channel to play. This is convenient when playing a Karaoke VCD.
ENGLISH ○○○○○○○○○ When playing VCD: Selecting multi-angle views While playing a disc containing multi-angle views, you can view the same scene at different angles. 1 STEREO LEFT RIGHT 2 Select a view angle you want. • STEREO: To listen to normal stereo (left/ right) playback. • LEFT: To listen to the left audio channel. • RIGHT: To listen to the right audio channel. Ex. 1/3 2/3 28 25-30_KD-AV7000[J]f.
To locate a folder by displaying the folder list • This functions only for MP3. 1 To locate a track by displaying the track list 1 ENGLISH ○○○○○○○○○ ○list○ ○ ○ ○ ○ ○ ○ ○ the Locating a folder/track using 2 2 3 Select a track you want. Current folder name or ID3 Tag (for MP3) Disc name (for CD) or CD Text 3 Select a folder you want. Current track name or ID3 Tag To next/previous page of the list To next/previous page of the list Ex. when playing MP3 29 25-30_KD-AV7000[J]f.
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ Selecting ○ ○ ○playback ○ ○modes ○○○○ ○○○○○○○○○ information Displaying the disc text With Auto Scroll or Scroll selected, you can display the text and scroll it on the monitor if it is long and cannot be displayed at a time. 1 You can use only one of the following playback modes at a time—Repeat Play, Random Play, and Intro Scan. • For VCD: While PBC is not in use. Repeat Play You can repeat playback. • Repeat Play can be deactivated only for DVD.
2 ENGLISH Random Play You can play back tracks at random. 1 When playing VCD/CD: INTRO SCAN TRACK 2 INTRO SCAN OFF When playing MP3: INTRO SCAN TRACK INTRO SCAN FOLDER INTRO SCAN OFF When playing VCD/CD: RANDOM PLAY DISC RANDOM PLAY OFF INTRO SCAN • TRACK: Plays the beginning of all tracks. • FOLDER: Plays the first tracks of all folders. • OFF: Cancels Intro Scan.
ENGLISH 3 3 Enter a number, then confirm. Ex. when playing DVD: Enter a number, then confirm. Ex. when playing DVD: Clear the entry. Confirm Clear the entry. Confirm Ex. when playing CD: When using the number buttons on the remote controller • To select number 5, press 5. • To select number 10, press 10. • To select number 23, press +10, +10, then 3. You cannot select folder using the remote controller.
You can play back two different sources as the main source (MAIN) and subsidiary source (SUB). You can listen to the main source through the speakers, while the subsidiary source through the monitor inserted into the cradle or the one connected to the AV OUTPUT jacks. • For connections of the cradle and an optional monitor, refer to the Installation/ Connection Manual (separate volume).
ENGLISH ○○○○○○○○○ Adjusting AV OUTPUT volume Select an appropriate volume level for the component connected to the AV OUTPUT jacks on the hideaway unit. • This functions without respect to the Dual Mode setting. 1 When using the remote controller: • For Dual Mode operations... – When controlling the monitor connected to the AV OUTPUT jacks, aim the remote controller at the remote sensor on the main unit.
ENGLISH Surround Mode Operations 1 2 *2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 Activate and select the surround mode or DSP mode. *2 See page 41. See page 41. See page 34. See page 39. 4 Make adjustment if you want to. • If neither surround mode nor DSP mode is activated, you cannot make adjustment. When surround mode is activated: When DSP mode is activated: 35 35-38_KD-AV7000[J]f.
ENGLISH ○○○○○○○○○ Introducing surround/DSP mode Surround modes Dolby Digital Dolby Digital is a digital signal compression method, developed by Dolby Laboratories, and enables multi-channel encoding and decoding (1ch up to 5.1ch). Dolby Digital 5.1 CH Dolby Digital 5.1 CH encoding method records and digitally compresses the left front channel, right front channel, center channel, left surround channel, right surround channel, and LFE channel signals (total 6 channels, but the LFE channel is counted as 0.
○○○○○○○○○3 ○ mode ○○○○○○○○ DSP You can use surround or Digital Signal Processor (DSP) mode while playing any source. However, when playing a multi-channel encoded disc, you cannot apply DSP mode to the playback sounds. • When “AUTO SURROUND” is set to “ON” (initial setting when shipped from factory), an appropriate surround mode is automatically selected without any setting operation (see page 50).
ENGLISH 4 Adjust the selected surround or DSP mode. When DSP mode is activated: When surround mode is activated: Ex. When selecting “HALL.” 1 Select one of the DSP modes. HALL: Reproduces the spatial feeling of a large shoeboxshaped hall designed primarily for classical concerts. : Selected automatically when multichannel DTS signal is detected (while playing a DVD or a DTS CD). No further adjustment is allowed.
The following operations are only possible for the main source when using Dual Mode. ENGLISH Sound Modes (iEQ) Operations 1 *2 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 See page 35. See page 35. See page 41. See page 41. See page 34. 4 Select one of the preset sound (iEQ) modes (then make adjustment if you want to make your own sound mode). Select sound modes. Adjust the level of each frequency band. Display the other set of the sound modes.
ENGLISH ○ ○your○own○ sound ○ ○modes ○○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Storing Selecting preset sound modes You can select a sound mode suitable to the music genre. Available sound modes: • HARD ROCK / R&B / POP / JAZZ / DANCE / COUNTRY / REGGAE / CLASSIC • USER1 / USER2 / USER3 • FLAT (To cancel the sound mode) You can adjust the sound modes and store your own adjustments in memory. 1 Repeat steps 1 to 4 on the left column to select a sound mode you want to adjust. 2 Make adjustments as you like.
Fader/Balance adjustments is only possible for the main source when using Dual Mode. ENGLISH Other Sound Adjustments 1 *2 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 See page 35. See page 35. See page 34. See page 39. 4 Make adjustment as you like. To adjust the input level This setting is required for each source except FM. Once you have made an adjustment, the volume level will automatically changes by adjusted level whenever you change the source.
ENGLISH Monitor Adjustments When no playback picture from the source is displayed, you can only adjust the brightness. 1 Display SCREEN CONTROL screen. Hold Adjustable items Hold ASPECT On the remote controller On the main unit 2 : Indicates the current ambient light level. As this level changes, the monitor adjusts the brightness automatically to match it to the current ambient light level. Select an item to adjust.
ENGLISH Initial Setup—DVD MENU You can preset the initial disc playback conditions. • While playing, no change can be made on the DVD Menu. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. 5 Change the setting. • For details, see the following pages. Ex. When setting “MONITOR TYPE.” 43 43-48_KD-AV7000[J]f.
ENGLISH MENU LANGUAGE Select the menu language. MONITOR TYPE Select the monitor type of your TV (connected to the AV OUTPUT jacks) to play DVD Video recorded with aspect ratio of 16:9. • For the removable monitor of this unit, set this to “16:9 AUTO.” • 16:9 NORMAL: Select when the aspect ratio of your TV is fixed to 16:9 (wide TV). AUDIO LANGUAGE Select the audio language. SUBTITLE Select the subtitle language. To erase the subtitle, select “OFF.
ENGLISH Initial Setup—MONITOR You can preset the initial monitor conditions. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. 5 Change the setting. • For details, see the following pages. Ex. When setting “BEEP TONE” to “OFF.” 45 43-48_KD-AV7000[J]f.
ENGLISH AUTO OPEN/CLOSE BEEP TONE • AUTO: The monitor comes out* or goes in automatically when you turn on or off the power. • OFF: Cancels this function. • ON: * If you close the monitor before turning off the power, the monitor will not come out next time you turn on the power. WIRING CHECK You can confirm the wiring connection is correctly done for particular functions. Sound beeps when you operate the unit. • OFF: Cancels this function.
ENGLISH Initial Setup—ON SCREEN You can preset the initial on-screen conditions. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. Language selection screen appears. 5 Change the setting. • For details, see the following pages. Ex. When setting “CLOCK” to “OFF.” 47 43-48_KD-AV7000[J]f.
ENGLISH ON SCREEN LANGUAGE You can select the language for this Setup Menu and some of the messages displayed on the monitor. MESSAGE • ON: Speaker/signal indicators (see page 69) and messages are displayed. Messages are displayed on the viewing window of the monitor screen... – When selecting repeat mode, random mode, intro scan, etc. – When starting Time Search, Title Search, Chapter Search, and Track Search. GUIDE Ex. One of the messages appears when selecting repeat mode.
You can preset the initial audio-related conditions and Preferred Setting Modes (PSM). • You cannot select “AUDIO MENU” when the subsidiary source operation screen is displayed on the monitor (with Dual Mode turned on; see page 33). ENGLISH Initial Setup—AUDIO MENU/PSM 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 5 Select the item you want. Appears when TV tuner unit KV-C1000 is connected.
ENGLISH AUTO SURROUND You can activate an appropriate surround mode automatically when a loaded disc is detected. • ON: An appropriate surround/DSP mode is automatically selected. • • • • • FRONT LEFT: FRONT RIGHT: ALL CENTER: REAR CENTER: For the front left seat. For the front right seat. For all front and rear seats. For the rear seats. : Displays the SPK DISTANCE screen. You can adjust the speaker distance from your listening position in meters or feet.
• SUBWOOFER: Select “YES” (connected) or “NO” (disconnected). • SUBWOOFER PHASE: Select either “NORMAL” or “REV. (reverse)” to obtain better subwoofer sounds. ENGLISH D (Dynamic). RANGE COMPRESSION You can enjoy a powerful sound even at a low volume level by compressing dynamic range (difference between the lowest and the highest frequency sounds). • This takes effect for all the playback sources.
ENGLISH AV2 INPUT SELECT You can determine the use of AV INPUT 2 jacks on the hideaway unit—select either “VIDEO” or “CAMERA.” • When the playback source is “AV2,” this setting cannot be changed. CAMERA VIEW • NORMAL: You can watch the rear view as the camera takes. • MIRROR: You can watch the rear view as reflected on the mirror. While watching the camera view, you can change it to the source playback screen by touching the center portion of the monitor screen.
○○○○○○○○○○○○○○○○○○ Assigning titles to the sources ENGLISH Other Main Functions Roman alphabet list Alternates between upper and lower cases. Backspace (Erase the last entry) Moves the cursor position. Upper cases Erase all entered character. Lower cases Confirm the entered name. Accented characters: Upper cases Display the other page of the character list of the same type. Entered name is displayed. Alternates between Roman alphabet and accented letter lists.
ENGLISH You can assign titles to 30 FM/AM, 30 TV stations, and 40 CDs (both in this unit and in the CD changer). Source Maximum character number Stations: 10 CDs: 32 If the “DELETE DISC NAME” or “DELETE STATION NAME” screen appears The internal memory is full. Delete unwanted names before assignment. • You cannot assign a title to CD Text and MP3 discs. 1 Prepare the source. • For FM/AM stations: Change “FM” or “AM,” then select a station. • For a CD in this unit: Insert a CD.
You can change the monitor position and the monitor angle. • Once you change them, they are stored. The monitor opens at the stored position and angle, next time you eject the monitor. To operate the car switches behind the monitor, press OPEN once. The monitor change its angle to the illustrated position for about 30 seconds. ENGLISH ○○○○○○○○○ ○○○○○○○○○ angle Changing the monitor position/ To return to its previous angle within 30 seconds, press OPEN again.
ENGLISH CD Changer Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current disc/folder/track no. Elapsed playing time Playback mode Sound mode (see page 39) Surround/DSP mode (see page 36) Volume level appears when adjusted. Disc text/ID3 tag information area Only for MP3 CD/CD Text MP3 Only for CD: See page 53. See page 14. See page 14. See page 15. See page 39. See pages 43 – 52. Back to the beginning 56 56-61_KD-AV7000[J]f.
2 Operate the disc 1 Select “CD-CH” ENGLISH Basic CD Changer Operations : Selects the disc. then : Selects the folder (only for MP3). : Goes back to the beginning of the current track, then skips to the previous tracks if pressed repeatedly. : Skips to the following tracks if pressed repeatedly. Ex. While playing CD/CD Text* * Disc text information recorded in the CD Text can be displayed when a JVC CD Text compatible CD changer is connected. Ex.
ENGLISH Advanced CD Changer Operations ○○○○○○○○○3 Selecting disc/folders/tracks Select a disc you want. You can select the disc, (folder: only for MP3,) and tracks using the buttons on the main unit. 1 DISC FOLDER TRACK 2 To next/previous page of the list Disc names will be shown once it is recognized. When using the remote controller You can directly select the disc number by pressing the corresponding number buttons (1 – 12).
○○○○○○○○○ ○○○○○○○○○ information Displaying the disc text Select a folder you want. Current track name or ID3 Tag With Auto Scroll or Scroll selected, you can display the text and scroll it on the monitor if it is long and cannot be displayed at a time. ENGLISH 3 1 To next/previous page of the list 2 (For CD) (For MP3) Shaded when no MP3 files are included. You cannot select this folder. Auto Scroll Scroll Off To locate a track by displaying the track list Example: while playing MP3.
ENGLISH ○○○○○○○○○ Selecting playback modes You can use only one of the following playback modes at a time—Repeat Play, Random Play, and Intro Scan. Repeat Play You can repeat playback. • Repeat Play cannot be deactivated. Random Play You can play back tracks at random.
1 Only for MP3 2 ○○○○○○○○○ Searching for songs You can use search functions to find your favorite tracks (for CD/MP3) and folders (for MP3). ENGLISH Intro Scan You can play back the first 15 seconds of each track sequentially. Folder/Track Search You can select a specific track (for CD/MP3) or folder (for MP3).
ENGLISH External Component Operations You can connect two video components as the playback components and an optional TV tuner unit (KV-C1000). • When you connect the video camera as a rear view camera to the AV INPUT 2 jacks to guide you to back the car, set the usage of the AV INPUT 2 jacks correctly (see page 52). • For connections, see the Installation/ Connection Manual (separate volume).
ENGLISH TV Tuner Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current preset no. Channel no. Search mode Sound mode (see page 39) Surround/DSP mode (see page 36) Volume level appears when adjusted. Playback picture will be shown in the picture view window. Available only after pressing “M” (next to this icon). See page 53. See page 14. See page 14. See page 15. (Not available while viewing the playback picture.) See page 39. See pages 43 – 52.
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ 3 Tune in to a TV station Watching TV programs • To tune in to a station using Preset Search, first store your favorite TV stations into memory (12 stations). 1 Select TV • For Auto Search, press either icon once. “Auto Search” begins. When a station is received, searching stops. • For Manual Search, press either icon repeatedly (or hold) until a station you want is selected. • For Preset Search, press either icon repeatedly until a preset number you want is selected.
1 Tune into a TV station. 1 then Select “MANUAL” (or “AUTO”). 2 2 ENGLISH To tune in to a preset station • See also “Watching TV programs” on page 64. Manual presetting Select a preset number. Store the station into a preset number. To select the rest of the preset stations then To select the rest of the preset stations Preset station information will be displayed. 65 62-66_KD-AV7000[J]f.
ENGLISH ○○○○○○○○○ Displaying the preset list You can store and select the preset station using the preset list on the monitor screen. To store a station using the preset list 1 Tune into a TV station. Select “MANUAL” (or “AUTO”). To select a preset station using the preset list then 1 2 2 3 Store the station into a preset number. To next/previous page of the list • Preset numbers, channel numbers and assigned names (see page 53) of the preset TV stations are shown on the list.
How to clean the monitor When removing stains or dust on the surface, turn off the monitor, then wipe with dry soft cloth. • Be careful not to scratch the surface when wiping it. • Do not use the following materials to clean the monitor: – Wet cloth – Volatile substance such as benzine and thinner – Acid detergent, alkaline detergent, and detergent composed of organic substance • When using chemically processed duster, read its precautions carefully.
ENGLISH More about This Receiver ○ ○ ○ ○ ○ ○ ○ ○ ○ Basic ○ ○Disc○Operations ○○○○○○ Operation Methods • Touch Panel screen goes off if no operations are made on it for about 30 seconds while viewing the playback picture. ○○○○○○○○○ Basic Operations Turning off the power • If you turn off the power while listening to a disc, disc play will start automatically, next time you turn on the power.
Speaker indicators Signal indicators SUBWFR SUBWFR – The speaker indicators—frames of “L,” “C,” “R,” “LS,” and “RS” light up, when the corresponding speakers are set to “LARGE” or “SMALL” (see page 51). Sounds come out of the speakers whose speaker indicators is lit on the display. indicator lights up when – The “SUBWOOFER” is set to “YES” (see page 51).
ENGLISH Notes on MP3 files • This unit can play back MP3 files only with the extension code <.mp3> (regardless of the letter case—upper/lower). • This unit cannot play back the files encoded in the following formats—MP3i, MP3 PRO, Layer 1, Layer 2 format. • This unit can show the names of albums, artists (performer), and tracks of ID3 Tag (Version 1.0 and 1.1). • This unit can show up to 64 characters on the monitor screen. • This unit can handle only one-byte characters.
• If you do not want to store your current adjustment, but only to apply the adjustment to the current playback source, press RETURN on the monitor screen to go back to the operation screen of the current source. Adjustment you made remains effective until you select a sound mode. MONITOR TYPE • When you select “16:9 NORMAL” for a picture whose aspect ratio is 4:3, the picture slightly changes due to the process for converting the picture width.
ENGLISH Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. General • Sound is sometimes interrupted. ] You are driving on rough roads. Stop playback while driving on rough roads. ] Disc is scratched. • Sound cannot be heard from the speakers. ] Connections are incorrect. • No sound comes out of the subwoofer (though it is activated—set to “YES”).
• Disc cannot be played back. ] MP3 tracks do not have the extension code—<.mp3>. ] MP3 tracks are not recorded in the format compliant with ISO 9660 Level 1, ISO 9660 Level 2, Romeo, or Joliet. • Noise is generated. ] The current track is not an MP3 file (although it has the extension code— <.mp3>). • Elapsed playing time is not correct. ] This sometimes occurs during play. This is caused by how the tracks are recorded on the disc. • Correct characters are not displayed.
ENGLISH Additional Information Preset iEQ mode The table below shows the preset frequency level settings for each iEQ mode.
Code Language Code Language Code Language AA AB AF AM AR AS AY AZ BA BE BG BH BI BN BO BR CA CO CS CY DA DZ EL EO ET EU FA FI FJ FO FY GA GD GL GN GU HA HI HR HU HY IA IE IK IN IS IW JI JW Afar Abkhazian Afrikaans Ameharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish Bhutani Greek Esperanto Estonian Basque Persian Finnish Fiji Faroese Frisian Irish Scots Gaelic Galician Guarani Gujarati Hausa Hindi
ENGLISH Specifications ○○○○○○○○○ Main unit AUDIO AMPLIFIER SECTION Maximum Power Output: Front: 50 W per channel Rear: 50 W per channel Center: 35 W Continuous Power Output (RMS): Front: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Rear: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Center: 15 W into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion.
Required space for the monitor ejection 177(7) ○○○○○○○○○ Hideaway unit 143.3(5-11/16) Input Terminals: AV INPUT 1/2: Audio: 0.5 Vrms (Left/Right) Video (composite): 1 Vp-p/75 Ω Output Terminals (Level/Impedance): AV OUTPUT: Audio: 2.0 V/20 kΩ load (full scale) Video (composite): 1 Vp-p/75 Ω PRE OUT: Audio: 2.
Having TROUBLE with operation? Please reset your unit Refer to page of How to Reset Still having trouble?? USA ONLY Call 1-800-252-5722 http://www.jvc.com We can help you! EN, SP, FR © 2004 Victor Company of Japan, Limited Cover_KD-AV7000[J]f.
KD-AV7000 LVT1171-002A [J] Installation/Connection Manual Manual de instalación/conexión Manuel d’installation/raccordement 0904MNMMDWJEIN EN, SP, FR © 2004 Victor Company of Japan, Limited ESPAÑOL ENGLISH FRANÇAIS This unit is designed to operate only on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
SYSTEM CONNECTIONS CONEXIONES DEL SISTEMA CONNEXIONS DU SYSTÈMES • For A , B , C , D , E , F , more information are given on the following pages. • En las siguientes páginas encontrará más información sobre A, B, C, D, E, F. • Pour A , B , C , D , E , F plus d’informations sont données aux pages suivantes.
INSTALLATION INSTALACIÓN INSTALLATION The following illustration shows a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits. La siguiente ilustración muestra una instalación típica. Sin embargo usted deberá efectuar los ajustes correspondientes a su automóvil.
ESPAÑOL ENGLISH FRANÇAIS Ç Electrical connections Ç Conexiones eléctricas Before connecting... • Make sure that the antenna cord from the car is connected to the hideaway unit (see page 2). If the antenna cord is not long enough, use the extension antenna cord (supplied). • Check the wiring in the car carefully. Incorrect connection may cause serious damage to the units. The leads of the power cord and those of the connector from the car body may be different in color. Antes de la conexión...
Connecting the parking brake wire Connect the parking brake wire to the parking brake system built in the car. Connexion du cordon de frein de stationnement Conexión del cable del freno de estacionamiento Conecte el cable del freno de estacionamiento al sistema de freno de estacionamiento del automóvil.
E Connecting the external amplifiers E Conexión de los amplificadores externos You can connect amplifiers to upgrade surround system in the car compartment. • Connect the PRE OUT terminals of the hideaway unit to the amplifier’s line-in terminals. • Disconnect the speakers from the hideaway unit, connect them to the amplifier. Leave the speaker leads of the unit unused. Podrá conectar amplificadores para mejorar el sistema de sonido envolvente del habitáculo de su automóvil.
NEDERLANDS FRANÇAIS DEUTSCH ENGLISH DVD RECEIVER WITH MONITOR DVD-RECEIVER MiT MONITOR RECEPTEUR DVD ET MONITOR DVD-RECEIVER MET MONITOR KD-AV7001 MAIN ATT SUB ZOOM DUAL AVOUT VOL ASPECT MENU TOPMENU OK RETURN TUNER DISC AV 1 2 4 5 6 7 8 9 11/0 12/+10 GUI SET UP Detachable 10 3 VOLUME • This unit is equipped with the display demonstration. To cancel it, see page 14. • Dieses Gerät ist mit einer Demonstrationsfunktion für das Display ausgestattet.
ENGLISH Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.
• DO NOT install any unit in locations where; – it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident. – it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident. – it may obstruct visibility. • DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident. • The driver must not watch the monitor while driving.
ENGLISH Contents How to reset your unit ..................................... 2 Important! (How to read this manual) ............. 3 Introduction—Playable Discs ....................... 5 Quick Guide—How to Use the Controls ...... 6 Remote controller ............................................ 6 Main unit (front) .............................................. 8 Preparation (Remote Controller— RM-RK220) .................................................... 9 Operation Methods ................................
Discs you can play You can play back the following discs on this unit: • DVD Video: whose video format is PAL or NTSC and whose region code is “2.” –DVD-Rs and DVD-RWs recorded in the DVD-Video format can also be played (see page 82). • Video CD (VCD)/Audio CD • MP3: CD-Rs or CD-RWs including MP3 files with the file extension code . They must be recorded in the format compliant with ISO 9660 Level 1, ISO 9660 Level 2, Romeo, and Joliet.
ENGLISH Quick Guide—How to Use the Controls ○○○○○○○○○ Remote controller Remote controller General operations Buttons MAIN ATT To do: SUB ATT Turn on the main unit. Turn off the main unit. ZOOM DUAL Attenuate sounds. TUNER Select “TUNER” and “DAB.” DISC Select “DISC” and “CD-CH.” AV Select external components: TV = AV1 = AV2 = AVOUT VOL ASPECT MENU GUI TOPMENU VOLUME OK RETURN MAIN SET UP TUNER DISC AV 1 2 3 SUB ZOOM Adjust the volume.
Buttons Buttons To do: Select the band. TUNER To do: 1 2 4 5 3 6 Start Auto Search. 7 8 9 Start Manual Search. 10 11/0 12/+10 Select title/chapter/track number. *3 ENGLISH Disc operations—continued Tuner operations Change preset numbers. 1 2 3 4 5 6 Select preset numbers directly. CD changer operations Buttons To do: Select folders. *2 Disc operations Buttons Select tracks. Search. To do: Play. Change discs. OK Pause. Stop. Select chapters/tracks. Search.
ENGLISH ○○○○○○○○○○○○○○○○○○ Main unit (front) : functions if pressed and held. CD changer operations Buttons To do: General operations Buttons Select tracks. Search. To do: Turn on the main unit. Turn off the main unit. Attenuate sounds. Change the sources. Adjust the volume. then (once): Display “DISC” = select discs. (twice): Display “FOLDER” = select folders.*1 TV tuner operations Buttons Start Auto Search. Change the display information. Detach the control panel.
WARNINGS on the battery: 1 (back side) 2 With the + side facing upwards Lithium coin battery (CR2025) ENGLISH Preparation (Remote Controller—RM-RK220) • Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. • Do not recharge, short, disassemble, or heat the battery or dispose of it in a fire. These behaviors may cause the battery to be overheated, crack or fire. • Do not leave the battery with other metallic materials.
ENGLISH Operation Methods You can operate this unit using three types of operation methods. • This instruction manual explains the operations mainly using the Touch Panel Icons shown on the monitor. • Using the Touch Panel Icons directly (See “BLIND CONTROL” on page 51.) Press the Touch Panel Icons with your finger directly (if you wear a glove, take it off). Examples: The following is just an example. On the actual monitor screen, the playback picture is shown (while video source is played back).
ENGLISH • Using the Graphic User Interface (GUI) from the remote controller You can use the Graphic User Interface in the same way as you touch the panel icons. Examples: 2 1 3 GUI OK OK SET UP Display GUI on the monitor (the cursor—yellow frame— appears around the currently selected icon). • While one of the video sources is selected, the GUI function turns on and off at a press of the button. Move the cursor to an icon you want. Confirm.
ENGLISH Basic Operations CAUTION on the monitor : Do not open or close the monitor by hand. Do not apply any force to the monitor while it is moving. Such a behavior may damage the monitor loading mechanism. For turning on the power, use the buttons on the main unit and the remote controller. 3 Adjust the volume To change the monitor angle: Hold 1 Turn on the power 2 • See page 60 for details.
You can also set the clock system to 24 hours or 12 hours. 1 Exit While playing any source... ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○5 Setting the clock To display the clock time: When the unit is turned off, the clock time is displayed on the display of the main unit for a while. On the main unit • If the touch panel icons are not shown on the monitor, touch the center portion of the monitor screen. 2 3 *1 *2 *1 When the unit is turned on...
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ Changing ○ ○ ○the ○graphic ○ ○screen○ ○ ○ Changing the source 1 While playing any source... You can select one of eight graphics in the picture view window. • See page 88 for each graphic screen. When shipped from the factory, display demonstration has been activated, and starts automatically when no operations are done for about 30 seconds (except while playing a DVD/ VCD).. To cancel it, select one of the graphic screen. 2 1 While playing any source... Ex.
You can display the level meter on the graphic screen, by selecting from four preset patterns. • While viewing the playback picture or display demonstration, you cannot show the level meter. 1 While playing any source... Ex. While listening to FM broadcast. 2 The following level meters are displayed in sequence.
ENGLISH Radio Operations Dual Mode indicator (see page 38) SOURCE icon (see pages 14 and 38) Current band/Preset no. Station frequency FM reception mode Search mode Sound mode (see page 44) Surround/DSP mode (see page 41) Volume level appears when adjusted. Not available for AM. Available only after pressing “M” (next to this icon). See page 14. See page 14. See page 15. See page 44. See pages 48 – 57. Back to the beginning 16 16-19_KD-AV7001[E]f.
• To tune in to a station using Preset Search, first store your favorite stations into memory (6 stations for each band: see page 18). 3 Select Search Mode ENGLISH Listening to the Radio 1 Select the Tuner AUTO: To start Auto Search. MANUAL: To start Manual Search. PRESET: then To select preset station numbers (only possible after storing stations in memory). 4 Tune in to a station 2 Select the band (FM/AM) • For Auto Search, press either icon once. “Auto Search” begins.
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○2 Storing stations in memory You can preset 6 stations for each band. then FM station automatic presetting—SSM (Strong-station Sequential Memory) • This functions only for FM bands. 1 Select the FM band (FM1 – FM3) you want to store FM stations into. Select “MANUAL” (or “AUTO”). 3 4 2 Tune in to a station. Store the station into a preset number. Start SSM. then then Preset station information will be displayed.
1 2 To store a station using the preset list 1 Select the band (FM1 – FM3, and AM) you want to store a station into. 2 Tune into a station. ENGLISH To tune in to a preset station • See also “Listening to the Radio” on page 17. then ○○○○○○○○○3 Select “MANUAL” (or “AUTO”). Displaying the preset list You can store and select the preset stations using the preset list on the monitor screen. To select a preset station using the preset list 4 Store the station into a preset number.
ENGLISH What you can do with RDS RDS (Radio Data System) allows FM stations to send an additional signal along with their regular programme signals. For example, the stations send their station names (PS), as well as information about what type of programme they broadcast, such as sports or music, etc.
○○○○○○○○○ Using the Standby Reception Select a PTY code. You can use two types of Standby Reception— TA Standby Reception and PTY Standby Reception. • You can display the other PTY codes in the PTY code list by pressing ∞ or 5. 4 Select the preset number. ENGLISH 3 TA Standby Reception TA Standby Reception allows the unit to switch temporarily to Traffic Announcement (TA) from any source other than AM.
ENGLISH PTY Standby Reception PTY Standby Reception allows the unit to switch temporarily to your favorite programme from any source other than AM. • When shipped from the factory, “NEWS” is selected for your favorite programme type. To change it to your favorite PTY code, see page 24. • If the DAB tuner is connected, Standby Reception also works for searching a service.
You can make RDS setting and use some other convenient functions. ENGLISH RDS Setup—RDS SET 1 2 3 Change the setting or enter the setting screen. • For details, see the following pages. Ex. When pressing “ALTERNATE FREQ.” 23 20-24_KD-AV7001[E]f.
ENGLISH ALTERNATE FREQ When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM RDS station of the same network, possibly broadcasting the same programme with stronger signals—NetworkTracking Reception. PTY STANDBY You can activate (ON) and deactivate (OFF) PTY Standby Reception for the FM tuner (and the DAB tuner if connected).
ENGLISH DVD/VCD Operations Dual Mode indicator (see page 38) SOURCE icon (see pages 14 and 38) PBC indicator (for VCD; see page 30) Current track no. (for VCD) Current title/chapter no. (for DVD) Play time information (see page 35) Audio signal format Playback mode (see page 35) Sound mode (see page 44) Surround/DSP mode (see page 41) Playback picture will be shown in the picture view window. Input signal channels are indicated a few second after detected. (See page 82.
ENGLISH CD/MP3 Operations Dual Mode indicator (see page 38) SOURCE icon (see pages 14 and 38) Current track no. (for CD) Current folder/track no. (for MP3) Play time information (see page 35) Audio signal format (only for DTS CD) Playback mode (see page 35) Sound mode (see page 44) Surround/DSP mode (see page 41) Disc text/ID3 tag information area Only for MP3 (see page 27) Playback buttons (see page 27) CD/CD Text MP3 Only for CD: See page 58. * See page 14. See page 14. See page 15. See page 44.
ENGLISH Basic Disc Operations Before performing any operations, observe the following... • For DVD playback, change the Setup Menu setting (see page 48). • If “ ” appears on the monitor, the disc cannot accept the operation you have tried. – In some cases, “ ” is not display, but operations will not be accepted. 1 Insert a disc 3 Operate the disc : Selects the folder (only for MP3). : Stops (see “Stopping play” on page 82). • VCD/CD/MP3 playback will continue endlessly until you stop it.
ENGLISH The following marks used in this manual indicate the playable discs. DVD To fast-forward or reverse the chapter or track, press ¡ or 1 on the remote controller while playing a disc. Each time you press the button, the search speed changes as follows: VCD with/without PBC VCD with PBC x2 \ x5 \ x10 \ x20 \ x60* To resume normal speed, press 3. CD All playable discs MP3 On-screen guide icons During play, the following guide icons may appear for a while on the monitor.
You can change the aspect ratio of the playback pictures. • This function is only possible using the buttons on the main unit or on the remote controller. • Aspect ratio cannot be changed while the GUI operation mode is activated. On the remote controller On the main unit You can lock a disc in the loading slot. ENGLISH ○ ○ ○disc○ejection ○○○○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Prohibiting Changing the aspect ratio While playing any source...
ENGLISH ○○○○○○○○○ Operating the disc menu Menu-driven playback is possible while playing back a DVD with menu-driven features or a VCD with the PlayBack Control (PBC) function. While playing a DVD: DVD discs generally have their own menus or title lists. A title list (TOP MENU) usually contains titles of movies and songs recorded. On the other hand, a menu (MENU) usually contains various information about the disc and playback selections.
To cancel the PBC playback You can cancel the menu-driven operations (PBC function) using the remote controller. ○○○○○○○○○ Zooming in You can zoom into a particular portion of the picture. • This function is only possible using the remote controller. 1 1 Press 7 to stop playback. 2 Press number buttons to select a track. Playback without PBC starts from the selected track.
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ Selecting ○ ○ ○audio○languages ○○○○○ Selecting subtitles While playing a chapter containing subtitles in different languages, you can select the subtitle language to display on the monitor. • You can also select the subtitle language using SETUP menu (see page 49). For DVD: While playing a chapter containing audio languages, you can select the language to listen to. • You can also select the audio language using SETUP menu (see page 49).
Selecting multi-angle views ENGLISH ○○○○○○○○○ When playing VCD: While playing a disc containing multi-angle views, you can view the same scene at different angles. 1 STEREO LEFT RIGHT 2 Select a view angle you want. • STEREO: To listen to normal stereo (left/ right) playback. • LEFT: To listen to the left audio channel. • RIGHT: To listen to the right audio channel. Ex. 1/3 2/3 3/3 33 30-35_KD-AV7001[E]f.
ENGLISH ○○○○○○○○○ ○list○ ○ ○ ○ ○ ○ ○ ○ the Locating a folder/track using To locate a folder by displaying the folder list • This functions only for MP3. 1 To locate a track by displaying the track list 1 2 2 3 Select a track you want. Current folder name or ID3 Tag (for MP3) Disc name (for CD) or CD Text 3 Select a folder you want. Current track name or ID3 Tag To next/previous page of the list To next/previous page of the list Ex. when playing MP3 34 30-35_KD-AV7001[E]f.
With Auto Scroll or Scroll selected, you can display the text and scroll it on the monitor if it is long and cannot be displayed at a time. 1 You can use only one of the following playback modes at a time—Repeat Play, Random Play, and Intro Scan. • For VCD: While PBC is not in use. ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ Selecting ○ ○ ○playback ○ ○modes ○○○○ ○○○○○○○○○ information Displaying the disc text Repeat Play You can repeat playback. • Repeat Play can be deactivated only for DVD.
ENGLISH Random Play You can play back tracks at random. 2 1 When playing VCD/CD: INTRO SCAN TRACK 2 INTRO SCAN OFF When playing MP3: INTRO SCAN TRACK INTRO SCAN FOLDER INTRO SCAN OFF When playing VCD/CD: RANDOM PLAY DISC RANDOM PLAY OFF INTRO SCAN • TRACK: Plays the beginning of all tracks. • FOLDER: Plays the first tracks of all folders. • OFF: Cancels Intro Scan.
3 Enter a number, then confirm. Ex. when playing DVD: Enter a number, then confirm. ENGLISH 3 Ex. when playing DVD: Clear the entry. Confirm Clear the entry. Confirm Ex. when playing CD: When using the number buttons on the remote controller • To select number 5, press 5. • To select number 10, press 10. • To select number 23, press +10, +10, then 3. You cannot select folder using the remote controller.
ENGLISH Dual Mode Operations You can play back two different sources as the main source (MAIN) and subsidiary source (SUB). You can listen to the main source through the speakers, while the subsidiary source through the monitor inserted into the cradle or the one connected to the AV OUTPUT jacks. • For connections of the cradle and an optional monitor, refer to the Installation/ Connection Manual (separate volume).
Select an appropriate volume level for the component connected to the AV OUTPUT jacks on the hideaway unit. • This functions without respect to the Dual Mode setting. 1 When using the remote controller: • For Dual Mode operations... – When controlling the monitor connected to the AV OUTPUT jacks, aim the remote controller at the remote sensor on the main unit. – When controlling the monitor inserted into the cradle, aim the remote controller at the remote sensor on the cradle.
ENGLISH Surround Mode Operations 1 2 *2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 Activate and select the surround mode or DSP mode. *2 See page 46. See page 46. See page 39. See page 44. 4 Make adjustment if you want to. • If neither surround mode nor DSP mode is activated, you cannot make adjustment. When surround mode is activated: When DSP mode is activated: 40 40-43_KD-AV7001[E]f.
Surround modes Dolby Digital Dolby Digital is a digital signal compression method, developed by Dolby Laboratories, and enables multi-channel encoding and decoding (1ch up to 5.1ch). Dolby Digital 5.1 CH Dolby Digital 5.1 CH encoding method records and digitally compresses the left front channel, right front channel, center channel, left surround channel, right surround channel, and LFE channel signals (total 6 channels, but the LFE channel is counted as 0.1 channel. Therefore, called 5.1 channel).
ENGLISH ○○○○○○○○○3 ○ mode ○○○○○○○○ DSP Turning on and off the surround/ You can use surround or Digital Signal Processor (DSP) mode while playing any source. However, when playing a multi-channel encoded disc, you cannot apply DSP mode to the playback sounds. • When “AUTO SURROUND” is set to “ON” (initial setting when shipped from factory), an appropriate surround mode is automatically selected without any setting operation (see page 55).
Adjust the selected surround or DSP mode. When DSP mode is activated: ENGLISH 4 When surround mode is activated: Ex. When selecting “HALL.” 1 Select one of the DSP modes. HALL: Reproduces the spatial feeling of a large shoeboxshaped hall designed primarily for classical concerts. : Selected automatically when multichannel DTS signal is detected (while playing a DVD or a DTS CD). No further adjustment is allowed.
ENGLISH Sound Modes (iEQ) Operations The following operations are only possible for the main source when using Dual Mode. 1 *2 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 See page 40. See page 40. See page 46. See page 46. See page 39. 4 Select one of the preset sound (iEQ) modes (then make adjustment if you want to make your own sound mode). Select sound modes. Adjust the level of each frequency band. Display the other set of the sound modes.
You can select a sound mode suitable to the music genre. Available sound modes: • HARD ROCK / R&B / POP / JAZZ / DANCE / COUNTRY / REGGAE / CLASSIC • USER1 / USER2 / USER3 • FLAT (To cancel the sound mode) You can adjust the sound modes and store your own adjustments in memory. 1 Repeat steps 1 to 4 on the left column to select a sound mode you want to adjust. 2 Make adjustments as you like. 3 After adjustment is finished...
ENGLISH Other Sound Adjustments Fader/Balance adjustments is only possible for the main source when using Dual Mode. 1 *2 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 See page 40. See page 40. See page 39. See page 44. 4 Make adjustment as you like. To adjust the input level This setting is required for each source except FM. Once you have made an adjustment, the volume level will automatically changes by adjusted level whenever you change the source.
When no playback picture from the source is displayed, you can only adjust the brightness. 1 Display SCREEN CONTROL screen. Hold ENGLISH Monitor Adjustments Adjustable items Hold ASPECT On the remote controller On the main unit 2 : Indicates the current ambient light level. As this level changes, the monitor adjusts the brightness automatically to match it to the current ambient light level. Select an item to adjust.
ENGLISH Initial Setup—DVD MENU You can preset the initial disc playback conditions. • While playing, no change can be made on the DVD Menu. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *2 *1 *1 3 See page 13. 4 Select the item you want. 5 Change the setting. • For details, see the following pages. Ex. When setting “MONITOR TYPE.” 48 48-53_KD-AV7001[E]f.
MONITOR TYPE Select the monitor type of your TV (connected to the AV OUTPUT jacks) to play DVD Video recorded with aspect ratio of 16:9. • For the removable monitor of this unit, set this to “16:9 AUTO.” ENGLISH MENU LANGUAGE Select the menu language. • 16:9 NORMAL: Select when the aspect ratio of your TV is fixed to 16:9 (wide TV). AUDIO LANGUAGE Select the audio language. SUBTITLE Select the subtitle language. To erase the subtitle, select “OFF.
ENGLISH Initial Setup—MONITOR You can preset the initial monitor conditions. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. 5 Change the setting. • For details, see the following pages. Ex. When setting “BEEP TONE” to “OFF.” 50 48-53_KD-AV7001[E]f.
BEEP TONE • AUTO: The monitor comes out* or goes in automatically when you turn on or off the power. • OFF: Cancels this function. • ON: * If you close the monitor before turning off the power, the monitor will not come out next time you turn on the power. WIRING CHECK You can confirm the wiring connection is correctly done for particular functions. Sound beeps when you operate the unit. • OFF: Cancels this function.
ENGLISH Initial Setup—ON SCREEN You can preset the initial on-screen conditions. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *2 *1 *1 3 See page 13. 4 Select the item you want. Language selection screen appears. 5 Change the setting. • For details, see the following pages. Ex. When setting “CLOCK” to “OFF.” 52 48-53_KD-AV7001[E]f.
MESSAGE • ON: Speaker/signal indicators (see page 82) and messages are displayed. ENGLISH ON SCREEN LANGUAGE You can select the language for this Setup Menu and some of the messages displayed on the monitor. Messages are displayed on the viewing window of the monitor screen... – When selecting repeat mode, random mode, intro scan, etc. – When starting Time Search, Title Search, Chapter Search, and Track Search. GUIDE Ex. One of the messages appears when selecting repeat mode.
ENGLISH Initial Setup—AUDIO MENU/PSM You can preset the initial audio-related conditions and Preferred Setting Modes (PSM). • You cannot select “AUDIO MENU” when the subsidiary source operation screen is displayed on the monitor (with Dual Mode turned on; see page 38). 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. 3 *1 *2 *1 See page 13. 4 Select the item you want. 5 Change the setting or enter the setting screen. • For details, see the following pages.
• ON: An appropriate surround/DSP mode is automatically selected. • FRONT LEFT: FRONT RIGHT: ALL CENTER: REAR CENTER: For the front left seat. For the front right seat. For all front and rear seats. For the rear seats. ENGLISH AUTO SURROUND You can activate an appropriate surround mode automatically when a loaded disc is detected. • • • • : Displays the SPK DISTANCE screen. You can adjust the speaker distance from your listening position in meters or feet.
ENGLISH D (Dynamic). RANGE COMPRESSION You can enjoy a powerful sound even at a low volume level by compressing dynamic range (difference between the lowest and the highest frequency sounds). • This takes effect for all the playback sources. • SUBWOOFER: Select “YES” (connected) or “NO” (disconnected). • SUBWOOFER PHASE: Select either “NORMAL” or “REV. (reverse)” to obtain better subwoofer sounds.
• VIDEO: The source “AV2” works for viewing the playback picture through the component connected to the AV INPUT 2 jacks. • CAMERA: Select this when connecting the rear view camera. – You can set the remaining two items (BACK GEAR/ CAMERA VIEW). BACK GEAR • AUTO: The rear view through the rear view camera is automatically displayed on the monitor when you change the gear to the back position. • OFF: Cancels this function. To watch the rear view, select “AV2” for the source.
ENGLISH Other Main Functions ○○○○○○○○○○○○○○○○○○ Assigning titles to the sources Roman alphabet list Alternates between upper and lower cases. Backspace (Erase the last entry) Moves the cursor position. Upper cases Erase all entered character. Lower cases Confirm the entered name. Accented characters: Upper cases Display the other page of the character list of the same type. Entered name is displayed. Alternates between Roman alphabet and accented letter lists.
Source Maximum character number TV Stations: 10 CDs: 32 If the “DELETE DISC NAME” or “DELETE STATION NAME” screen appears The internal memory is full. Delete unwanted names before assignment. ENGLISH You can assign titles to 30 TV stations and 40 CDs (both in this unit and in the CD changer). • You cannot assign a title to CD Text and MP3 discs. • If you change the “TV CHANNEL AREA” setting (see page 57), assigned TV station names are all erased. 1 Ex. When trying a name to a 41st disc.
ENGLISH ○○○○○○○○○ ○○○○○○○○○ angle Changing the monitor position/ You can change the monitor position and the monitor angle. • Once you change them, they are stored. The monitor opens at the stored position and angle, next time you eject the monitor. To operate the car switches behind the monitor, press OPEN once. The monitor change its angle to the illustrated position for about 30 seconds. To return to its previous angle within 30 seconds, press OPEN again.
ENGLISH CD Changer Operations Dual Mode indicator (see page 38) SOURCE icon (see pages 14 and 38) Current disc/folder/track no. Elapsed playing time Playback mode Sound mode (see page 44) Surround/DSP mode (see page 41) Volume level appears when adjusted. Disc text/ID3 tag information area Only for MP3 CD/CD Text MP3 Only for CD: See page 58. See page 14. See page 14. See page 15. See page 44. See pages 48 – 57. Back to the beginning 61 61-66_KD-AV7001[E]f.
ENGLISH Basic CD Changer Operations 2 Operate the disc 1 Select “CD-CH” : Selects the disc. then : Selects the folder (only for MP3). : Goes back to the beginning of the current track, then skips to the previous tracks if pressed repeatedly. Ex. While playing CD/CD Text* : Skips to the following tracks if pressed repeatedly. * Disc text information recorded in the CD Text can be displayed when a JVC CD Text compatible CD changer is connected. Ex.
○○○○○○○○○3 Selecting disc/folders/tracks Select a disc you want. ENGLISH Advanced CD Changer Operations You can select the disc, (folder: only for MP3,) and tracks using the buttons on the main unit. 1 DISC FOLDER TRACK 2 To next/previous page of the list Assigned disc names will be shown once it is recognized. When using the remote controller You can directly select the disc number by pressing the corresponding number buttons (1 – 12).
ENGLISH 3 ○○○○○○○○○ ○○○○○○○○○ information Displaying the disc text Select a folder you want. Current track name or ID3 Tag With Auto Scroll or Scroll selected, you can display the text and scroll it on the monitor if it is long and cannot be displayed at a time. 1 To next/previous page of the list Shaded when no MP3 files are included. You cannot select this folder. 2 (For CD) To locate a track by displaying the track list Example: while playing MP3.
You can use only one of the following playback modes at a time—Repeat Play, Random Play, and Intro Scan. Repeat Play You can repeat playback. • Repeat Play cannot be deactivated. Random Play You can play back tracks at random.
ENGLISH Intro Scan You can play back the first 15 seconds of each track sequentially. 1 Only for MP3 2 ○○○○○○○○○ Searching for songs You can use search functions to find your favorite tracks (for CD/MP3) and folders (for MP3). Folder/Track Search You can select a specific track (for CD/MP3) or folder (for MP3).
You can connect two video components as the playback components and an optional TV tuner unit (KV-C1001). • When you connect the video camera as a rear view camera to the AV INPUT 2 jacks to guide you to back the car, set the usage of the AV INPUT 2 jacks correctly (see page 57). • For connections, see the Installation/ Connection Manual (separate volume).
ENGLISH TV Tuner Operations Dual Mode indicator (see page 38) SOURCE icon (see pages 14 and 38) Current preset no. Channel no. Search mode Sound mode (see page 44) Surround/DSP mode (see page 41) Volume level appears when adjusted. Playback picture will be shown in the picture view window. Available only after pressing “M” (next to this icon). See page 58. See page 14. See page 14. See page 15. (Not available while viewing the playback picture.) See page 44. See pages 48 – 57.
Before watching TV, select the area where you use the optional TV tuner unit (KV-C1001)— see page 57. • To tune in to a station using Preset Search, first store your favorite TV stations into memory (12 stations). ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ 3 Tune in to a TV station Watching TV programs • For Auto Search, press either icon once. “Auto Search” begins. When a station is received, searching stops. • For Manual Search, press either icon repeatedly (or hold) until a station you want is selected.
ENGLISH To tune in to a preset station • See also “Watching TV programs” on page 69. Manual presetting 1 Tune into a TV station. 1 then Select “MANUAL” (or “AUTO”). 2 2 Select a preset number. Store the station into a preset number. To select the rest of the preset stations then To select the rest of the preset stations Preset station information will be displayed. 70 67-71_KD-AV7001[E]f.
You can store and select the preset station using the preset list on the monitor screen. To store a station using the preset list 1 Tune into a TV station. ENGLISH ○○○○○○○○○ Displaying the preset list Select “MANUAL” (or “AUTO”). To select a preset station using the preset list then 1 2 2 3 Store the station into a preset number. To next/previous page of the list • Preset numbers, channel numbers and assigned names (see page 58) of the preset TV stations are shown on the list.
ENGLISH DAB Tuner Operations Dual Mode indicator (see page 38) SOURCE icon (see pages 14 and 38) Service type (primary or secondary)/ Service label/Current band/Preset no. Channel no. Ensemble frequency TEXT indicator (DLS—DAB radio text) Search mode Sound mode (see page 44) Surround/DSP mode (see page 41) ANN (Announcement) indicator Volume level appears when adjusted. Ensemble label/ PTY code/ Service label Works only while receiving an ensemble. *1 See page 14. See page 14. See page 15. See page 44.
It is recommended to use DAB (Digital Audio Broadcasting) tuner KT-DB1000 with this unit. If you have another DAB tuner, consult your JVC IN-CAR ENTERTAINMENT dealer. • Refer also to the Instructions supplied with your DAB tuner. • To tune into a service using Preset Search, first store your favorite services into memory (6 stations for each band: see page 74). 1 Select the DAB Tuner 3 Select Search Mode AUTO: ENGLISH Listening to the DAB Tuner To start Auto Search. MANUAL: To start Manual Search.
ENGLISH What is DAB system? DAB can deliver CD quality sound without any annoying interference and signal distortion. Furthermore, it can carry text, pictures, and data. In contrast to FM broadcast, where each programme is transmitted on its own frequency, DAB combines several programmes (called “services”) to form one “ensemble.” In addition, each “service”—called “primary service”—can also be divided into its components (called “secondary service”).
To store a service using the preset list 1 Select the band (DAB1 – DAB3) you want to store a service into. 2 Tune into a service. 1 2 ENGLISH To tune in to a preset service • See also “Listening to the DAB Tuner” on page 73. then Select “MANUAL” (or “AUTO”). ○○○○○○○○○ 3 Displaying the preset list You can store and select the preset services using the preset list on the monitor screen. 4 Store the service into a preset number.
ENGLISH ○○○○○○○○○ Displaying the DAB text You can change the initial display—label information (ensemble label/service label/PTY code) to the DAB radio text information— Dynamic Label Segment (DLS). • This function is available only when DLS is received. If the current service provides DLS, the TEXT indicator appears on the monitor screen. To erase the DLS While DLS is displayed on the monitor... 1 • Each time you press the icon, the DLS comes on and goes off.
TRAVEL: Announcement Standby Reception allows the unit to switch temporarily to your favorite service (announcement type) from any source except FM and AM. WARNING: Warnings about earthquakes, tsunami, etc. NEWS: News 1 EVENT: Programmes about travel destinations, package tours, and travel ideas and opportunities ENGLISH ○○○○○○○○○ ○○○○○○○○○ Reception Using Announcement Standby WEATHER: Weather information Information about events, concerts, etc. SPECIAL: 2 Select an announcement type.
ENGLISH DAB Setup—DAB SET You can make DAB setting and use some other convenient functions. 1 2 3 Change the setting or enter the setting screen. • For details, see the following pages. Ex. When pressing “DAB BAND RANGE.” 78 72-79_KD-AV7001[E]f.
PTY STANDBY CODE Select the PTY code for PTY Standby Reception (see also page 24). ENGLISH DAB BAND RANGE DAB ensembles are broadcast on the following bands: • Band III: 174.928 MHz to 239.200 MHz • L-Band: 1452.960 MHz to 1490.624 MHz In some areas, both bands are used, and in other areas only one of them is used. Select the proper band for your area. • You cannot select a different PTY code separately for the DAB tuner and for the FM tuner.
ENGLISH Maintenance How to clean the monitor When removing stains or dust on the surface, turn off the monitor, then wipe with dry soft cloth. • Be careful not to scratch the surface when wiping it. • Do not use the following materials to clean the monitor: – Wet cloth – Volatile substance such as benzine and thinner – Acid detergent, alkaline detergent, and detergent composed of organic substance • When using chemically processed duster, read its precautions carefully.
○ ○ ○ ○ ○ ○ ○ ○ ○ Basic ○ ○Disc○Operations ○○○○○○ Operation Methods • Touch Panel screen goes off if no operations are made on it for about 30 seconds while viewing the playback picture. ○○○○○○○○○ Basic Operations Turning off the power • If you turn off the power while listening to a disc, disc play will start automatically, next time you turn on the power.
ENGLISH • This unit cannot play back the files which have the data such as WMA, WAVE, ATRAC3, MPEG 2.5, etc. • The speaker/signal indicators appear in the following cases (for DVD/CD): – When a different type of the digital signal is detected, or – When you start playback or resume playback from pause.
Notes on MP3 files • This unit can play back MP3 files only with the extension code <.mp3> (regardless of the letter case—upper/lower). • This unit cannot play back the files encoded in the following formats—MP3i, MP3 PRO, Layer 1, Layer 2 format. • This unit can show the names of albums, artists (performer), and tracks of ID3 Tag (Version 1.0 and 1.1). • This unit can show up to 64 characters on the monitor screen. • This unit can handle only one-byte characters.
ENGLISH • When an optional monitor is connected to the AV OUTPUT terminal, you can view the following MP3 CONTROL screen on the optional monitor. 1 MP3 CONTROL REPEAT TRACK 3 2 Time : 00:03:08 Folder : 01 / 10 Track : 01 / 30 spring sumer fall winter sea begonia.mp3 german chamomile.mp3 kiwi fruit.mp3 orchard grass.mp3 petunia.mp3 north pole.mp3 begonia2.mp3 german chamomile2.mp3 kiwi fruit2.mp3 orchard grass2.mp3 petunia2.mp3 north pole2.
• You may not able to adjust the brightness in the following case: – You cannot make it brighter when the ambient light is very bright. – You cannot make it darker when the ambient light is very dark. Assigning titles to the sources • When the CD changer is connected, you can assign titles to CDs in the CD changer. These titles can also be shown on the display if you insert the CDs in this unit.
ENGLISH Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. General • Sound is sometimes interrupted. ] You are driving on rough roads. Stop playback while driving on rough roads. ] Disc is scratched. • Sound cannot be heard from the speakers. ] Connections are incorrect. • No sound comes out of the subwoofer (though it is activated—set to “YES”).
• Elapsed playing time is not correct. ] This sometimes occurs during play. This is caused by how the tracks are recorded on the disc. • Correct characters are not displayed. ] This unit can only display a limited number of special characters (see the tables on page 58). Initial setup—AUDIO MENU/PSM • “SPEAKER SIZE” settings change. ] Speaker size settings are very much related to one another. For example, if you set the FRONT speakers to “NONE,” you cannot select “NONE” for the REAR speakers.
ENGLISH Additional Information Preset iEQ mode The table below shows the preset frequency level settings for each iEQ mode.
Code Language Code Language Code Language AA AB AF AM AR AS AY AZ BA BE BG BH BI BN BO BR CA CO CS CY DA DZ EL EO ET EU FA FI FJ FO FY GA GD GL GN GU HA HI HR HU HY IA IE IK IN IS IW JI JW Afar Abkhazian Afrikaans Ameharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish Bhutani Greek Esperanto Estonian Basque Persian Finnish Fiji Faroese Frisian Irish Scots Gaelic Galician Guarani Gujarati Hausa Hindi
ENGLISH Specifications ○○○○○○○○○ Main unit AUDIO AMPLIFIER SECTION Maximum Power Output: Front: 50 W per channel Rear: 50 W per channel Center: 35 W Continuous Power Output (RMS): Front: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Rear: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Center: 15 W into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion.
Required space for the monitor ejection ○○○○○○○○○ Hideaway unit Input Terminals: AV INPUT 1/2: Audio: 0.5 Vrms (Left/Right) Video (composite): 1 Vp-p/75 Ω Output Terminals (Level/Impedance): AV OUTPUT: Audio: 2.0 V/20 kΩ load (full scale) Video (composite): 1 Vp-p/75 Ω PRE OUT: Audio: 2.
Having TROUBLE with operation? Please reset your unit Refer to page of How to reset your unit Haben Sie PROBLEME mit dem Betrieb? Bitte setzen Sie Ihr Gerät zurück Siehe Seite Zurücksetzen des Geräts Vous avez des PROBLÈMES de fonctionnement? Réinitialisez votre appareil Référez-vous à la page intitulée Comment réinitialiser votre appareil Hebt u PROBLEMEN met de bediening? Stel het apparaat terug Zie de pagina met de paragraaf Het apparaat terugstellen EN, GE, FR, NL 1004MNMMDWJEIN © 2004 Victor Comp
KD-AV7001 LVT1172-005A [E] Installation/Connection Manual Einbau/Anschlußanleitung Manuel d’installation/raccordement Handleiding voor installatie/aansluiting 1004MNMMDWJEIN EN, GE, FR, NL © 2004 Victor Company of Japan, Limited ENGLISH DEUTSCH This unit is designed to operate only on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC IN-CAR ENTERTAINMENT dealers.
SYSTEM CONNECTIONS SYSTEMANSCHLÜSSE CONNEXIONS DU SYSTÈMES SYSTEEMVERBINDINGEN • For A , B , C , C , D , E , F , more information are given on the following pages. • Für A , B , C , C , D , E , F werden weitere Informationen auf den folgenden Seiten gegeben. • Pour A , B , C , C , D , E , F plus d’informations sont données aux pages suivantes. C D • Voor A , B , C , C , D , E , F vindt u meer informatie op de volgende bladzijden.
INSTALLATION INSTALLATION INSTALLATION INSTALLEREN The following illustration shows a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your JVC IN-CAR ENTERTAINMENT dealer or a company supplying kits. Die folgende Abbildung zeigt die typische Installation. Sie müssen aber Justierungen entsprechend des vorliegenden Fahrzeugs vornehmen.
ENGLISH DEUTSCH FRANÇAIS NEDERLANDS Ç Electrical connections / Elektrische Verbindungen / Connexions électriques / Elektrische verbindingen If your car is equipped with the ISO connector For some VW/Audi or Opel (Vauxhall) automobile Wenn Ihr Auto mit ISO-Steckern ausgestattet ist Für manche VW/Audi oder Opel (Vauxhall) Fahrzeuge From the car body Si votre voiture est équippée d’un connecteur ISO Pour certaine voiture VW/Audi ou Opel (Vauxhall) Von der Karosserie A B Indien uw auto is uitgerust met de
Before connecting... • Make sure that the aerial cord from the car is connected to the hideway unit (see page 2). If the aerial cord is not long enough, use the extension aerial cord (supplied). • Check the wiring in the car carefully. Incorrect connection may cause serious damage to the units. The leads of the power cord and those of the connector from the car body may be different in color. Avant de commencer...
D Connecting the cradle / Anschließen der Halterung / Connexion du berceau / Aansluiten van de bak En utilisant le berceau (KV-CR101/KV-CR100), il est possible séparer le moniteur de l’appareil principal et de l’insérez dans le berceau de façon que les personnes assises sur les sièges arrière puissent voir l’image de lecture même lors que le conducteur conduit la voiture.
ENGLISH DVD RECEIVER WITH MONITOR !"=asa= ‡§√◊ËÕ߇≈Ëπ DVD æ√ÈÕ¡®Õ¿“æ ‰∑¬ KD-AV7005 MAIN ATT SUB ZOOM DUAL AVOUT VOL ASPECT MENU GUI TOPMENU OK RETURN DISC AV SET UP TUNER 1 2 4 5 6 7 8 9 11/0 12/+10 10 Detachable 3 VOLUME • This unit is equipped with the display demonstration. To cancel it, see page 14. • !"#$%&'()*+,&'-.
ENGLISH Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.
CAUTIONS on the monitor • DO NOT install any unit in locations where; – it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident. – it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident. – it may obstruct visibility. • DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident. • The driver must not watch the monitor while driving.
ENGLISH Contents How to reset your unit ..................................... 2 Important! (How to read this manual) ............. 3 Surround Mode Operations ........................ 35 Introducing surround/DSP mode ................... 36 Turning on and off the surround/DSP mode .... 37 Introduction—Playable Discs ....................... 5 Quick Guide—How to Use the Controls ...... 6 Remote controller ............................................ 6 Main unit (front) .......................................
Discs you can play You can play back the following discs on this unit: • DVD Video: whose video format is NTSC or PAL and whose region code is “3.” –DVD-Rs and DVD-RWs recorded in the DVD-Video format can also be played (see page 69). • Video CD (VCD)/Audio CD • MP3: CD-Rs or CD-RWs including MP3 files with the file extension code . They must be recorded in the format compliant with ISO 9660 Level 1, ISO 9660 Level 2, Romeo, and Joliet.
ENGLISH Quick Guide—How to Use the Controls ○○○○○○○○○ Remote controller General operations Buttons ATT To do: Turn on the main unit. Turn off the main unit. MAIN ATT Attenuate sounds. SUB TUNER ZOOM DUAL AVOUT VOL DISC Select “DISC” and “CD-CH.” AV Select external components: TV = AV1 = AV2 = VOLUME MAIN SUB ASPECT MENU TOPMENU Select “TUNER.” Adjust the volume. Set the main or suboperation for Dual Mode. *1 ZOOM Turn on/off Dual Mode.
Buttons Disc operations—continued To do: Buttons Select the band. TUNER To do: Return to the previous screen while operating the disc menu. RETURN Start Auto Search. Start Manual Search. Change preset numbers. 1 2 3 4 5 6 Select preset numbers directly. 2 4 5 3 6 7 8 9 10 11/0 12/+10 Select title/chapter/track number. *3 CD changer operations Disc operations Buttons 1 ENGLISH Tuner operations Buttons To do: To do: Play. Select folders. *2 Pause. Select tracks. Stop.
ENGLISH ○○○○○○○○○○○○○○○○○○ Main unit (front) Display CD changer operations General operations Buttons Buttons To do: To do: Turn on the main unit. Select tracks. Turn off the main unit. Search. Attenuate sounds. then Change the sources. Adjust the volume. Change the display information. (once): Display “DISC” = select discs. (twice): Display “FOLDER” = select folders.*1 TV tuner operations Buttons Detach the control panel. To do: Start Auto Search. Start Manual Search.
WARNINGS on the battery: 1 (back side) 2 With the + side facing upwards Lithium coin battery (CR2025) ENGLISH Preparation (Remote Controller—RM-RK220) • Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. • Do not recharge, short, disassemble, or heat the battery or dispose of it in a fire. These behaviors may cause the battery to be overheated, crack or fire. • Do not leave the battery with other metallic materials.
ENGLISH Operation Methods You can operate this unit using three types of operation methods. • This instruction manual explains the operations mainly using the Touch Panel Icons shown on the monitor. • Using the Touch Panel Icons directly (See “BLIND CONTROL” on page 46.) Press the Touch Panel Icons with your finger directly (if you wear a glove, take it off). Examples: The following is just an example. On the actual monitor screen, the playback picture is shown (while video source is played back).
ENGLISH • Using the Graphic User Interface (GUI) from the remote controller You can use the Graphic User Interface in the same way as you touch the panel icons. Examples: 2 1 3 GUI OK OK SET UP Display GUI on the monitor (the cursor—yellow frame— appears around the currently selected icon). • While one of the video sources is selected, the GUI function turns on and off at a press of the button. Move the cursor to an icon you want. Confirm.
ENGLISH Basic Operations CAUTION on the monitor : Do not open or close the monitor by hand. Do not apply any force to the monitor while it is moving. Such a behavior may damage the monitor loading mechanism. For turning on the power, use the buttons on the main unit and the remote controller. 3 Adjust the volume To change the monitor angle: Hold 1 Turn on the power • See page 55 for details.
You can also set the clock system to 24 hours or 12 hours. 1 Exit While playing any source... ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○5 Setting the clock To display the clock time: On the main unit When the unit is turned off, the clock time is displayed on the display of the main unit for a while. • If the touch panel icons are not shown on the monitor, touch the center portion of the monitor screen. 2 3 *1 *2 *1 When the unit is turned on...
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ Changing ○ ○ ○the ○graphic ○ ○screen○ ○ ○ Changing the source 1 While playing any source... You can select one of eight graphics in the picture view window. • See page 74 for each graphic screen. When shipped from the factory, display demonstration has been activated, and starts automatically when no operations are done for about 30 seconds (except while playing a DVD/ VCD). To cancel it, select one of the graphic screen. 2 1 2 While playing any source... Ex.
You can display the level meter on the graphic screen, by selecting from four preset patterns. • While viewing the playback picture or display demonstration, you cannot show the level meter. 1 While playing any source... Ex. While listening to FM broadcast. 2 The following level meters are displayed in sequence.
ENGLISH Radio Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current band/Preset no. Station frequency FM reception mode Search mode Sound mode (see page 39) Surround/DSP mode (see page 36) Volume level appears when adjusted. Not available for AM. Available only after pressing “M” (next to this icon). See page 53. See page 14. See page 14. See page 15. See page 39. See pages 43 – 52. Back to the beginning 16 16-19_KD-AV7005[U]f.
• To tune in to a station using Preset Search, first store your favorite stations into memory (6 stations for each band: see page 18). 3 Select Search Mode ENGLISH Listening to the Radio 1 Select the Tuner AUTO: To start Auto Search. MANUAL: To start Manual Search. PRESET: then To select preset station numbers (only possible after storing stations in memory). 4 Tune in to a station 2 Select the band (FM/AM) • For Auto Search, press either icon once. “Auto Search” begins.
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○2 Storing stations in memory You can preset 6 stations for each band. then FM station automatic presetting—SSM (Strong-station Sequential Memory) • This functions only for FM bands. 1 Select the FM band (FM1 – FM3) you want to store FM stations into. Select “MANUAL” (or “AUTO”). 3 4 2 Tune in to a station. Store the station into a preset number. Start SSM. then then Preset station information will be displayed.
1 2 To store a station using the preset list 1 Select the band (FM1 – FM3, and AM) you want to store a station into. 2 Tune into a station. ENGLISH To tune in to a preset station • See also “Listening to the Radio” on page 17. then Select “MANUAL” (or “AUTO”). ○○○○○○○○○3 Displaying the preset list You can store and select the preset stations using the preset list on the monitor screen. To select a preset station using the preset list 4 Store the station into a preset number.
ENGLISH DVD/VCD Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) PBC indicator (for VCD; see page 25) Current track no. (for VCD) Current title/chapter no. (for DVD) Play time information (see page 30) Audio signal format Playback mode (see page 30) Sound mode (see page 39) Surround/DSP mode (see page 36) Playback picture will be shown in the picture view window. Input signal channels are indicated a few second after detected. (See page 69.
ENGLISH CD/MP3 Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current track no. (for CD) Current folder/track no. (for MP3) Play time information (see page 30) Audio signal format (only for DTS CD) Playback mode (see page 30) Sound mode (see page 39) Surround/DSP mode (see page 36) Disc text/ID3 tag information area Only for MP3 (see page 22) Playback buttons (see page 22) CD/CD Text MP3 Only for CD: See page 53. * See page 14. See page 14. See page 15. See page 39.
ENGLISH Basic Disc Operations Before performing any operations, observe the following... • For DVD playback, change the Setup Menu setting (see page 43). • If “ ” appears on the monitor, the disc cannot accept the operation you have tried. – In some cases, “ ” is not display, but operations will not be accepted. 1 Insert a disc 3 Operate the disc : Selects the folder (only for MP3). : Stops (see “Stopping play” on page 69). • VCD/CD/MP3 playback will continue endlessly until you stop it.
To fast-forward or reverse the chapter or track, press ¡ or 1 on the remote controller while playing a disc. Each time you press the button, the search speed changes as follows: DVD VCD with PBC VCD with/without PBC ENGLISH The following marks used in this manual indicate the playable discs. x2 \ x5 \ x10 \ x20 \ x60* To resume normal speed, press 3. CD MP3 All playable discs On-screen guide icons During play, the following guide icons may appear for a while on the monitor.
ENGLISH ○ ○ ○disc○ejection ○○○○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Prohibiting Changing the aspect ratio You can change the aspect ratio of the playback pictures. • This function is only possible using the buttons on the main unit or on the remote controller. • Aspect ratio cannot be changed while the GUI operation mode is activated. On the remote controller On the main unit You can lock a disc in the loading slot. While playing any source...
Menu-driven playback is possible while playing back a DVD with menu-driven features or a VCD with the PlayBack Control (PBC) function. While playing a DVD: DVD discs generally have their own menus or title lists. A title list (TOP MENU) usually contains titles of movies and songs recorded. On the other hand, a menu (MENU) usually contains various information about the disc and playback selections. 1 While playing a VCD: The PBC function allows you to operate the VCD using menus.
ENGLISH When using the number buttons on the remote controller • To select number 5, press 5. • To select number 10, press 10. • To select number 23, press +10, +10, then 3. ○○○○○○○○○ Zooming in To cancel the PBC playback You can zoom into a particular portion of the picture. • This function is only possible using the remote controller. You can cancel the menu-driven operations (PBC function) using the remote controller. 1 1 Press 7 to stop playback. 2 Press number buttons to select a track.
While playing a chapter containing subtitles in different languages, you can select the subtitle language to display on the monitor. • You can also select the subtitle language using SETUP menu (see page 44). For DVD: While playing a chapter containing audio languages, you can select the language to listen to. • You can also select the audio language using SETUP menu (see page 44). 1 For VCD: While playing a track, you can select the audio channel to play. This is convenient when playing a Karaoke VCD.
ENGLISH ○○○○○○○○○ When playing VCD: Selecting multi-angle views While playing a disc containing multi-angle views, you can view the same scene at different angles. 1 STEREO LEFT RIGHT 2 Select a view angle you want. • STEREO: To listen to normal stereo (left/ right) playback. • LEFT: To listen to the left audio channel. • RIGHT: To listen to the right audio channel. Ex. 1/3 2/3 28 25-30_KD-AV7005[U]f.
To locate a folder by displaying the folder list • This functions only for MP3. 1 To locate a track by displaying the track list 1 ENGLISH ○○○○○○○○○ ○list○ ○ ○ ○ ○ ○ ○ ○ the Locating a folder/track using 2 2 3 Select a track you want. Current folder name or ID3 Tag (for MP3) Disc name (for CD) or CD Text 3 Select a folder you want. Current track name or ID3 Tag To next/previous page of the list Ex. when playing MP3 To next/previous page of the list 29 25-30_KD-AV7005[U]f.
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ Selecting ○ ○ ○playback ○ ○modes ○○○○ ○○○○○○○○○ information Displaying the disc text With Auto Scroll or Scroll selected, you can display the text and scroll it on the monitor if it is long and cannot be displayed at a time. 1 You can use only one of the following playback modes at a time—Repeat Play, Random Play, and Intro Scan. • For VCD: While PBC is not in use. Repeat Play You can repeat playback. • Repeat Play can be deactivated only for DVD.
2 ENGLISH Random Play You can play back tracks at random. 1 When playing VCD/CD: INTRO SCAN TRACK 2 INTRO SCAN OFF When playing MP3: INTRO SCAN TRACK INTRO SCAN FOLDER INTRO SCAN OFF When playing VCD/CD: RANDOM PLAY DISC RANDOM PLAY OFF INTRO SCAN • TRACK: Plays the beginning of all tracks. • FOLDER: Plays the first tracks of all folders. • OFF: Cancels Intro Scan.
ENGLISH 3 3 Enter a number, then confirm. Ex. when playing DVD: Enter a number, then confirm. Ex. when playing DVD: Clear the entry. Confirm Clear the entry. Confirm Ex. when playing CD: When using the number buttons on the remote controller • To select number 5, press 5. • To select number 10, press 10. • To select number 23, press +10, +10, then 3. You cannot select folder using the remote controller.
You can play back two different sources as the main source (MAIN) and subsidiary source (SUB). You can listen to the main source through the speakers, while the subsidiary source through the monitor inserted into the cradle or the one connected to the AV OUTPUT jacks. • For connections of the cradle and an optional monitor, refer to the Installation/ Connection Manual (separate volume).
ENGLISH ○○○○○○○○○ Adjusting AV OUTPUT volume Select an appropriate volume level for the component connected to the AV OUTPUT jacks on the hideaway unit. • This functions without respect to the Dual Mode setting. 1 When using the remote controller: • For Dual Mode operations... – When controlling the monitor connected to the AV OUTPUT jacks, aim the remote controller at the remote sensor on the main unit.
ENGLISH Surround Mode Operations 1 2 *2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 Activate and select the surround mode or DSP mode. *2 See page 41. See page 41. See page 34. See page 39. 4 Make adjustment if you want to. • If neither surround mode nor DSP mode is activated, you cannot make adjustment. When surround mode is activated: When DSP mode is activated: 35 35-38_KD-AV7005[U]f.
ENGLISH ○○○○○○○○○ Introducing surround/DSP mode Surround modes Dolby Digital Dolby Digital is a digital signal compression method, developed by Dolby Laboratories, and enables multi-channel encoding and decoding (1ch up to 5.1ch). Dolby Digital 5.1 CH Dolby Digital 5.1 CH encoding method records and digitally compresses the left front channel, right front channel, center channel, left surround channel, right surround channel, and LFE channel signals (total 6 channels, but the LFE channel is counted as 0.
○○○○○○○○○3 ○ mode ○○○○○○○○ DSP You can use surround or Digital Signal Processor (DSP) mode while playing any source. However, when playing a multi-channel encoded disc, you cannot apply DSP mode to the playback sounds. • When “AUTO SURROUND” is set to “ON” (initial setting when shipped from factory), an appropriate surround mode is automatically selected without any setting operation (see page 50).
ENGLISH 4 Adjust the selected surround or DSP mode. When DSP mode is activated: When surround mode is activated: Ex. When selecting “HALL.” 1 Select one of the DSP modes. HALL: Reproduces the spatial feeling of a large shoeboxshaped hall designed primarily for classical concerts. : Selected automatically when multichannel DTS signal is detected (while playing a DVD or a DTS CD). No further adjustment is allowed.
The following operations are only possible for the main source when using Dual Mode. ENGLISH Sound Modes (iEQ) Operations 1 *2 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 See page 35. See page 35. See page 41. See page 41. See page 34. 4 Select one of the preset sound (iEQ) modes (then make adjustment if you want to make your own sound mode). Select sound modes. Adjust the level of each frequency band. Display the other set of the sound modes.
ENGLISH ○ ○your○own○ sound ○ ○modes ○○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Storing Selecting preset sound modes You can select a sound mode suitable to the music genre. Available sound modes: • HARD ROCK / R&B / POP / JAZZ / DANCE / COUNTRY / REGGAE / CLASSIC • USER1 / USER2 / USER3 • FLAT (To cancel the sound mode) You can adjust the sound modes and store your own adjustments in memory. 1 Repeat steps 1 to 4 on the left column to select a sound mode you want to adjust. 2 Make adjustments as you like.
Fader/Balance adjustments is only possible for the main source when using Dual Mode. ENGLISH Other Sound Adjustments 1 *2 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 See page 35. See page 35. See page 34. See page 39. 4 Make adjustment as you like. To adjust the input level This setting is required for each source except FM. Once you have made an adjustment, the volume level will automatically changes by adjusted level whenever you change the source.
ENGLISH Monitor Adjustments When no playback picture from the source is displayed, you can only adjust the brightness. 1 Display SCREEN CONTROL screen. Hold Adjustable items Hold ASPECT On the remote controller On the main unit 2 : Indicates the current ambient light level. As this level changes, the monitor adjusts the brightness automatically to match it to the current ambient light level. Select an item to adjust.
ENGLISH Initial Setup—DVD MENU You can preset the initial disc playback conditions. • While playing, no change can be made on the DVD Menu. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. 5 Change the setting. • For details, see the following pages. Ex. When setting “MONITOR TYPE.” 43 43-48_KD-AV7005[U]f.
ENGLISH MENU LANGUAGE Select the menu language. MONITOR TYPE Select the monitor type of your TV (connected to the AV OUTPUT jacks) to play DVD Video recorded with aspect ratio of 16:9. • For the removable monitor of this unit, set this to “16:9 AUTO.” • 16:9 NORMAL: Select when the aspect ratio of your TV is fixed to 16:9 (wide TV). AUDIO LANGUAGE Select the audio language. SUBTITLE Select the subtitle language. To erase the subtitle, select “OFF.
ENGLISH Initial Setup—MONITOR You can preset the initial monitor conditions. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. 5 Change the setting. • For details, see the following pages. Ex. When setting “BEEP TONE” to “OFF.” 45 43-48_KD-AV7005[U]f.
ENGLISH AUTO OPEN/CLOSE BEEP TONE • AUTO: The monitor comes out* or goes in automatically when you turn on or off the power. • OFF: Cancels this function. • ON: * If you close the monitor before turning off the power, the monitor will not come out next time you turn on the power. WIRING CHECK You can confirm the wiring connection is correctly done for particular functions. Sound beeps when you operate the unit. • OFF: Cancels this function.
ENGLISH Initial Setup—ON SCREEN You can preset the initial on-screen conditions. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. Language selection screen appears. 5 Change the setting. • For details, see the following pages. Ex. When setting “CLOCK” to “OFF.” 47 43-48_KD-AV7005[U]f.
ENGLISH ON SCREEN LANGUAGE You can select the language for this Setup Menu and some of the messages displayed on the monitor. MESSAGE • ON: Speaker/signal indicators (see page 69) and messages are displayed. Messages are displayed on the viewing window of the monitor screen... – When selecting repeat mode, random mode, intro scan, etc. – When starting Time Search, Title Search, Chapter Search, and Track Search. GUIDE Ex. One of the messages appears when selecting repeat mode.
You can preset the initial audio-related conditions and Preferred Setting Modes (PSM). • You cannot select “AUDIO MENU” when the subsidiary source operation screen is displayed on the monitor (with Dual Mode turned on; see page 33). ENGLISH Initial Setup—AUDIO MENU/PSM 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. Appears when TV tuner unit KV-C1001 or KV-C1000 is connected.
ENGLISH AUTO SURROUND You can activate an appropriate surround mode automatically when a loaded disc is detected. • ON: An appropriate surround/DSP mode is automatically selected. • • • • • FRONT LEFT: FRONT RIGHT: ALL CENTER: REAR CENTER: For the front left seat. For the front right seat. For all front and rear seats. For the rear seats. : Displays the SPK DISTANCE screen. You can adjust the speaker distance from your listening position in meters or feet.
• SUBWOOFER: Select “YES” (connected) or “NO” (disconnected). • SUBWOOFER PHASE: Select either “NORMAL” or “REV. (reverse)” to obtain better subwoofer sounds. ENGLISH D (Dynamic). RANGE COMPRESSION You can enjoy a powerful sound even at a low volume level by compressing dynamic range (difference between the lowest and the highest frequency sounds). • This takes effect for all the playback sources.
ENGLISH AV2 INPUT SELECT You can determine the use of AV INPUT 2 jacks on the hideaway unit—select either “VIDEO” or “CAMERA.” • When the playback source is “AV2,” this setting cannot be changed. • VIDEO: The source “AV2” works for viewing the playback picture through the component connected to the AV INPUT 2 jacks. • CAMERA: Select this when connecting the rear view camera. – You can set the remaining two items (BACK GEAR/ CAMERA VIEW).
○○○○○○○○○○○○○○○○○○ Assigning titles to the sources ENGLISH Other Main Functions Roman alphabet list Alternates between upper and lower cases. Backspace (Erase the last entry) Moves the cursor position. Upper cases Erase all entered character. Lower cases Confirm the entered name. Accented characters: Upper cases Display the other page of the character list of the same type. Entered name is displayed. Alternates between Roman alphabet and accented letter lists.
ENGLISH You can assign titles to 30 FM/AM, 30 TV stations, and 40 CDs (both in this unit and in the CD changer). Source Maximum character number Stations: 10 CDs: 32 If the “DELETE DISC NAME” or “DELETE STATION NAME” screen appears The internal memory is full. Delete unwanted names before assignment. • You cannot assign a title to CD Text and MP3 discs. • For the TV tuner unit KV-C1001 users: If you change the “TV CHANNEL AREA” setting (see page 52), assigned TV station names are all erased.
You can change the monitor position and the monitor angle. • Once you change them, they are stored. The monitor opens at the stored position and angle, next time you eject the monitor. To operate the car switches behind the monitor, press OPEN once. The monitor change its angle to the illustrated position for about 30 seconds. ENGLISH ○○○○○○○○○ ○○○○○○○○○ angle Changing the monitor position/ To return to its previous angle within 30 seconds, press OPEN again.
ENGLISH CD Changer Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current disc/folder/track no. Elapsed playing time Playback mode Sound mode (see page 39) Surround/DSP mode (see page 36) Volume level appears when adjusted. Disc text/ID3 tag information area Only for MP3 CD/CD Text MP3 Only for CD: See page 53. See page 14. See page 14. See page 15. See page 39. See pages 43 – 52. Back to the beginning 56 56-61_KD-AV7005[U]f.
2 Operate the disc 1 Select “CD-CH” ENGLISH Basic CD Changer Operations : Selects the disc. then : Selects the folder (only for MP3). : Goes back to the beginning of the current track, then skips to the previous tracks if pressed repeatedly. : Skips to the following tracks if pressed repeatedly. Ex. While playing CD/CD Text* * Disc text information recorded in the CD Text can be displayed when a JVC CD Text compatible CD changer is connected. Ex.
ENGLISH Advanced CD Changer Operations ○○○○○○○○○3 Selecting disc/folders/tracks Select a disc you want. You can select the disc, (folder: only for MP3,) and tracks using the buttons on the main unit. 1 DISC FOLDER TRACK 2 To next/previous page of the list Disc names will be shown once it is recognized. When using the remote controller You can directly select the disc number by pressing the corresponding number buttons (1 – 12).
○○○○○○○○○ ○○○○○○○○○ information Displaying the disc text Select a folder you want. Current track name or ID3 Tag With Auto Scroll or Scroll selected, you can display the text and scroll it on the monitor if it is long and cannot be displayed at a time. ENGLISH 3 1 To next/previous page of the list 2 (For CD) (For MP3) Shaded when no MP3 files are included. You cannot select this folder. Auto Scroll Scroll Off To locate a track by displaying the track list Example: while playing MP3.
ENGLISH ○○○○○○○○○ Selecting playback modes You can use only one of the following playback modes at a time—Repeat Play, Random Play, and Intro Scan. Repeat Play You can repeat playback. • Repeat Play cannot be deactivated. Random Play You can play back tracks at random.
1 Only for MP3 2 ○○○○○○○○○ Searching for songs You can use search functions to find your favorite tracks (for CD/MP3) and folders (for MP3). ENGLISH Intro Scan You can play back the first 15 seconds of each track sequentially. Folder/Track Search You can select a specific track (for CD/MP3) or folder (for MP3).
ENGLISH External Component Operations You can connect two video components as the playback components and an optional TV tuner unit (KV-C1000/KV-C1001). • When you connect the video camera as a rear view camera to the AV INPUT 2 jacks to guide you to back the car, set the usage of the AV INPUT 2 jacks correctly (see page 52). • For connections, see the Installation/ Connection Manual (separate volume).
ENGLISH TV Tuner Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current preset no. Channel no. Search mode Sound mode (see page 39) Surround/DSP mode (see page 36) Volume level appears when adjusted. Playback picture will be shown in the picture view window. Available only after pressing “M” (next to this icon). See page 53. See page 14. See page 14. See page 15. (Not available while viewing the playback picture.) See page 39. See pages 43 – 52.
ENGLISH ○ ○ ○ ○ ○ ○ ○ ○ ○ 3 Tune in to a TV station Watching TV programs Only for TV tuner unit KV-C1001 users: Before watching TV, select the area (see page 52). • To tune in to a station using Preset Search, first store your favorite TV stations into memory (12 stations). • For Auto Search, press either icon once. “Auto Search” begins. When a station is received, searching stops. • For Manual Search, press either icon repeatedly (or hold) until a station you want is selected.
1 Tune into a TV station. 1 then Select “MANUAL” (or “AUTO”). 2 2 ENGLISH To tune in to a preset station • See also “Watching TV programs” on page 64. Manual presetting Select a preset number. Store the station into a preset number. To select the rest of the preset stations then To select the rest of the preset stations Preset station information will be displayed. 65 62-66_KD-AV7005[U]f.
ENGLISH ○○○○○○○○○ Displaying the preset list You can store and select the preset station using the preset list on the monitor screen. To store a station using the preset list 1 Tune into a TV station. Select “MANUAL” (or “AUTO”). To select a preset station using the preset list then 1 2 2 3 Store the station into a preset number. To next/previous page of the list • Preset numbers, channel numbers and assigned names (see page 53) of the preset TV stations are shown on the list.
How to clean the monitor When removing stains or dust on the surface, turn off the monitor, then wipe with dry soft cloth. • Be careful not to scratch the surface when wiping it. • Do not use the following materials to clean the monitor: – Wet cloth – Volatile substance such as benzine and thinner – Acid detergent, alkaline detergent, and detergent composed of organic substance • When using chemically processed duster, read its precautions carefully.
ENGLISH More about This Receiver ○ ○ ○ ○ ○ ○ ○ ○ ○ Basic ○ ○Disc○Operations ○○○○○○ Operation Methods • Touch Panel screen goes off if no operations are made on it for about 30 seconds while viewing the playback picture. ○○○○○○○○○ Basic Operations Turning off the power • If you turn off the power while listening to a disc, disc play will start automatically, next time you turn on the power.
Speaker indicators Signal indicators Ejecting a disc • If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to prevent it from dust. (Disc will not play this time.) ENGLISH • The speaker/signal indicators appear in the following cases (only for DVD/CD): – When a different type of the digital signal is detected, or – When you start playback or resume playback from pause.
ENGLISH Notes on MP3 files • This unit can play back MP3 files only with the extension code <.mp3> (regardless of the letter case—upper/lower). • This unit cannot play back the files encoded in the following formats—MP3i, MP3 PRO, Layer 1, Layer 2 format. • This unit can show the names of albums, artists (performer), and tracks of ID3 Tag (Version 1.0 and 1.1). • This unit can show up to 64 characters on the monitor screen. • This unit can handle only one-byte characters.
• If you do not want to store your current adjustment, but only to apply the adjustment to the current playback source, press RETURN on the monitor screen to go back to the operation screen of the current source. Adjustment you made remains effective until you select a sound mode. MONITOR TYPE • When you select “16:9 NORMAL” for a picture whose aspect ratio is 4:3, the picture slightly changes due to the process for converting the picture width.
ENGLISH Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. General • Sound is sometimes interrupted. ] You are driving on rough roads. Stop playback while driving on rough roads. ] Disc is scratched. • Sound cannot be heard from the speakers. ] Connections are incorrect. • No sound comes out of the subwoofer (though it is activated—set to “YES”).
• Elapsed playing time is not correct. ] This sometimes occurs during play. This is caused by how the tracks are recorded on the disc. • Correct characters are not displayed. ] This unit can only display a limited number of special characters (see the tables on page 53). Initial setup—AUDIO MENU/PSM • “SPEAKER SIZE” settings change. ] Speaker size settings are very much related to one another. For example, if you set the FRONT speakers to “NONE,” you cannot select “NONE” for the REAR speakers.
ENGLISH Additional Information Preset iEQ mode The table below shows the preset frequency level settings for each iEQ mode.
Code Language Code Language Code Language AA AB AF AM AR AS AY AZ BA BE BG BH BI BN BO BR CA CO CS CY DA DZ EL EO ET EU FA FI FJ FO FY GA GD GL GN GU HA HI HR HU HY IA IE IK IN IS IW JI JW Afar Abkhazian Afrikaans Ameharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish Bhutani Greek Esperanto Estonian Basque Persian Finnish Fiji Faroese Frisian Irish Scots Gaelic Galician Guarani Gujarati Hausa Hindi
ENGLISH Specifications Having TROUBLE with operation? Please reset your unit. Refer to page of How to reset your unit. ○○○○○○○○○ Main unit AUDIO AMPLIFIER SECTION Maximum Power Output: Front: 50 W per channel Rear: 50 W per channel Center: 35 W Continuous Power Output (RMS): Front: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Rear: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion.
Required space for the monitor ejection 177 143.3 15 12.2 ○○○○○○○○○ Hideaway unit Input Terminals: AV INPUT 1/2: Audio: 0.5 Vrms (Left/Right) Video (composite): 1 Vp-p/75 Ω Output Terminals (Level/Impedance): AV OUTPUT: Audio: 2.0 V/20 kΩ load (full scale) Video (composite): 1 Vp-p/75 Ω PRE OUT: Audio: 2.
EN, CT, TH © 2004 Victor Company of Japan, Limited Cover_KD-AV7005[U]_1_2.
KD-AV7005 LVT1173-002A [U] Installation/Connection Manual / ! 1004MNMMDWJEIN EN, CT, TH °“√µ‘¥µ—Èß/§ŸË¡◊Õ°“√µ‘¥µ—Èß © 2004 Victor Company of Japan, Limited ENGLISH ‰∑¬ This unit is designed to operate only on 12 V DC, NEGATIVE !"#$%== 1 2 V !"#$%& !"#$% ground electrical systems. If your vehicle does not have this !"#$%&'( )!*+,-%./0= JVC= ! system, a voltage inverter is required, which can be purchased at !"#$ JVC car audio dealers.
SYSTEM CONNECTIONS • For A , B , C , D , E , F , more information are given on the following pages. • F D ! °“√µËÕ‡™◊ËÕ¡√–∫∫ !"#$%&= A =I B =I C =I D =I E =I F = !"# ë ”À√—∫ A , B , C , D , E , F ¥Ÿ√“¬≈–‡Õ’¬¥‡æ‘¡Ë ‡µ‘¡„πÀπÈ“∂—¥‰ª A B (KV-C1000 or KV-C1001) (KV-C1000 KV-C1001) (KV-C1000 À√◊Õ KV-C1001) 4 RESET 3 2 1 TV ANTENNA C REMOTE SENSOR B C E TV TUNER UNIT TV tuner unit !" AV OUTPUT VIDEO CD L ‡§√◊ËÕ߇≈Ëπ CD changer (CH-X1500, etc.
INSTALLATION The following illustration shows a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits. !"#$%&'()*+,-./0123451&6 !"#$%&'()*+,-./012345678 JVC !"#$%&'()*+,-.
ENGLISH ‰∑¬ Ç Electrical connections Ç Before connecting... • Make sure that the antenna cord from the car is connected to the hideaway unit (see page 2). If the antenna cord is not long enough, use the extension antenna cord (supplied). • Check the wiring in the car carefully. Incorrect connection may cause serious damage to the units. The leads of the power cord and those of the connector from the car body may be different in color.
Connecting the parking brake wire Connect the parking brake wire to the parking brake system built in the car. !"#$%& °“√µËÕ “¬‡∫√°¡◊Õ !"#$%&'()*+ ), !"-.
E E Connecting the external amplifiers You can connect amplifiers to upgrade surround system in the car compartment. • Connect the PRE OUT terminals of the hideaway unit to the amplifier’s line-in terminals. • Disconnect the speakers from the hideaway unit, connect them to the amplifier. Leave the speaker leads of the unit unused. !"#$%& E !"#$%&' ()*+,-./01234 • !"#$%&'()*PRE OUT !"#$%& !"#$ • !"#$%&'()*+ ,-.
DVD RECEIVER WITH MONITOR KD-AV7008 MAIN ATT SUB ZOOM DUAL AVOUT VOL ASPECT MENU GUI TOPMENU OK RETURN DISC AV SET UP TUNER Detachable 1 2 4 5 6 7 8 9 11/0 12/+10 10 3 VOLUME COMPACT DIGITAL VIDEO • This unit is equipped with the display demonstration. To cancel it, see page 14. For installation and connections, refer to the separate manual. INSTRUCTIONS LVT1174-001A [A] Cover_KD-AV7008[A]f.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.
WARNINGS CAUTIONS on the monitor • DO NOT install any unit in locations where; – it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident. – it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident. – it may obstruct visibility. • DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident. • The driver must not watch the monitor while driving.
Contents How to reset your unit ..................................... 2 Important! (How to read this manual) ............. 3 Surround Mode Operations ........................ 35 Introducing surround/DSP mode ................... 36 Turning on and off the surround/DSP mode .... 37 Introduction—Playable Discs ....................... 5 Quick Guide—How to Use the Controls ...... 6 Remote controller ............................................ 6 Main unit (front) ..............................................
Introduction—Playable Discs Discs you can play You can play back the following discs on this unit: • DVD Video: whose video format is NTSC or PAL and whose region code is “4.” –DVD-Rs and DVD-RWs recorded in the DVD-Video format can also be played (see page 69). • Video CD (VCD)/Audio CD • MP3: CD-Rs or CD-RWs including MP3 files with the file extension code . They must be recorded in the format compliant with ISO 9660 Level 1, ISO 9660 Level 2, Romeo, and Joliet.
Quick Guide—How to Use the Controls ○○○○○○○○○ Remote controller General operations Buttons ATT To do: Turn on the main unit. Turn off the main unit. MAIN ATT Attenuate sounds. SUB TUNER ZOOM DUAL AVOUT VOL DISC Select “DISC” and “CD-CH.” AV Select external components: TV = AV1 = AV2 = VOLUME MAIN SUB ASPECT MENU TOPMENU Select “TUNER.” Adjust the volume. Set the main or suboperation for Dual Mode. *1 ZOOM Turn on/off Dual Mode.
Tuner operations Buttons Disc operations—continued To do: Buttons Select the band. TUNER To do: Return to the previous screen while operating the disc menu. RETURN Start Auto Search. Start Manual Search. Change preset numbers. 1 2 3 4 5 6 Select preset numbers directly. 2 4 5 3 6 7 8 9 10 11/0 12/+10 Select title/chapter/track number. *3 CD changer operations Disc operations Buttons 1 Buttons To do: To do: Play. Select folders. *2 Pause. Select tracks. Stop. Search.
○○○○○○○○○○○○○○○○○○ Main unit (front) Display CD changer operations General operations Buttons Buttons To do: To do: Turn on the main unit. Select tracks. Turn off the main unit. Search. Attenuate sounds. Change the sources. (If power is off, it comes on.) Adjust the volume. Change the display information. then (once): Display “DISC” = select discs. (twice): Display “FOLDER” = select folders.*1 TV tuner operations Buttons Detach the control panel. To do: Start Auto Search.
Preparation (Remote Controller—RM-RK220) WARNINGS on the battery: 1 (back side) 2 With the + side facing upwards Lithium coin battery (CR2025) • Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. • Do not recharge, short, disassemble, or heat the battery or dispose of it in a fire. These behaviors may cause the battery to be overheated, crack or fire. • Do not leave the battery with other metallic materials.
Operation Methods You can operate this unit using three types of operation methods. • This instruction manual explains the operations mainly using the Touch Panel Icons shown on the monitor. • Using the Touch Panel Icons directly (See “BLIND CONTROL” on page 46.) Press the Touch Panel Icons with your finger directly (if you wear a glove, take it off). Examples: The following is just an example. On the actual monitor screen, the playback picture is shown (while video source is played back).
• Using the Graphic User Interface (GUI) from the remote controller You can use the Graphic User Interface in the same way as you touch the panel icons. Examples: 2 1 3 GUI OK OK SET UP Display GUI on the monitor (the cursor—yellow frame— appears around the currently selected icon). • While one of the video sources is selected, the GUI function turns on and off at a press of the button. Move the cursor to an icon you want. Confirm.
Basic Operations CAUTION on the monitor : Do not open or close the monitor by hand. Do not apply any force to the monitor while it is moving. Such a behavior may damage the monitor loading mechanism. For turning on the power, use the buttons on the main unit and the remote controller. 3 Adjust the volume To change the monitor angle: Hold 1 Turn on the power • See page 55 for details.
○ ○ ○ ○ ○ ○ ○ ○ ○5 Setting the clock You can also set the clock system to 24 hours or 12 hours. 1 Exit While playing any source... To display the clock time: On the main unit When the unit is turned off, the clock time is displayed on the display of the main unit for a while. • If the touch panel icons are not shown on the monitor, touch the center portion of the monitor screen. 2 3 *1 *2 *1 When the unit is turned on...
○ ○ ○ ○ ○ ○ ○ ○ ○ Changing ○ ○ ○the ○graphic ○ ○screen○ ○ ○ Changing the source 1 While playing any source... You can select one of eight graphics in the picture view window. • See page 74 for each graphic screen. When shipped from the factory, display demonstration has been activated, and starts automatically when no operations are done for about 30 seconds (except while playing a DVD/ VCD). To cancel it, select one of the graphic screen. 2 1 2 While playing any source... Ex.
○○○○○○○○○ Displaying the level meter You can display the level meter on the graphic screen, by selecting from four preset patterns. • While viewing the playback picture or display demonstration, you cannot show the level meter. 1 While playing any source... Ex. While listening to FM broadcast. 2 The following level meters are displayed in sequence. How to read the display of the main unit: While listening to radio (FM/AM): 1 2 3 4 1 Lights up when Dolby Pro Logic II is activated (see page 36).
Radio Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current band/Preset no. Station frequency FM reception mode Search mode Sound mode (see page 39) Surround/DSP mode (see page 36) Volume level appears when adjusted. Not available for AM. Available only after pressing “M” (next to this icon). See page 53. See page 14. See page 14. See page 15. See page 39. See pages 43 – 52. Back to the beginning 16 16-19_KD-AV7008[A]f.
Listening to the Radio • To tune in to a station using Preset Search, first store your favorite stations into memory (6 stations for each band: see page 18). 3 Select Search Mode 1 Select the Tuner AUTO: To start Auto Search. MANUAL: To start Manual Search. PRESET: then To select preset station numbers (only possible after storing stations in memory). 4 Tune in to a station 2 Select the band (FM/AM) • For Auto Search, press either icon once. “Auto Search” begins.
○ ○ ○ ○ ○ ○ ○ ○ ○2 Storing stations in memory You can preset 6 stations for each band. then FM station automatic presetting—SSM (Strong-station Sequential Memory) • This functions only for FM bands. 1 Select the FM band (FM1 – FM3) you want to store FM stations into. Select “MANUAL” (or “AUTO”). 3 4 2 Tune in to a station. Store the station into a preset number. Start SSM. then then Preset station information will be displayed.
To tune in to a preset station • See also “Listening to the Radio” on page 17. 1 2 To store a station using the preset list 1 Select the band (FM1 – FM3, and AM) you want to store a station into. 2 Tune into a station. then Select “MANUAL” (or “AUTO”). ○○○○○○○○○3 Displaying the preset list You can store and select the preset stations using the preset list on the monitor screen. To select a preset station using the preset list 4 Store the station into a preset number.
DVD/VCD Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) PBC indicator (for VCD; see page 25) Current track no. (for VCD) Current title/chapter no. (for DVD) Play time information (see page 30) Audio signal format Playback mode (see page 30) Sound mode (see page 39) Surround/DSP mode (see page 36) Playback picture will be shown in the picture view window. Input signal channels are indicated a few second after detected. (See page 69.
CD/MP3 Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current track no. (for CD) Current folder/track no. (for MP3) Play time information (see page 30) Audio signal format (only for DTS CD) Playback mode (see page 30) Sound mode (see page 39) Surround/DSP mode (see page 36) Disc text/ID3 tag information area Only for MP3 (see page 22) Playback buttons (see page 22) CD/CD Text MP3 Only for CD: See page 53. * See page 14. See page 14. See page 15. See page 39.
Basic Disc Operations Before performing any operations, observe the following... • For DVD playback, change the Setup Menu setting (see page 43). • If “ ” appears on the monitor, the disc cannot accept the operation you have tried. – In some cases, “ ” is not display, but operations will not be accepted. 1 Insert a disc 3 Operate the disc : Selects the folder (only for MP3). : Stops (see “Stopping play” on page 69). • VCD/CD/MP3 playback will continue endlessly until you stop it. : Starts playback.
The following marks used in this manual indicate the playable discs. To fast-forward or reverse the chapter or track, press ¡ or 1 on the remote controller while playing a disc. Each time you press the button, the search speed changes as follows: DVD VCD with PBC VCD with/without PBC x2 \ x5 \ x10 \ x20 \ x60* To resume normal speed, press 3. CD MP3 All playable discs On-screen guide icons During play, the following guide icons may appear for a while on the monitor.
○ ○ ○disc○ejection ○○○○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Prohibiting Changing the aspect ratio You can change the aspect ratio of the playback pictures. • This function is only possible using the buttons on the main unit or on the remote controller. • Aspect ratio cannot be changed while the GUI operation mode is activated. On the remote controller On the main unit You can lock a disc in the loading slot. While playing any source...
○○○○○○○○○ Operating the disc menu Menu-driven playback is possible while playing back a DVD with menu-driven features or a VCD with the PlayBack Control (PBC) function. While playing a DVD: DVD discs generally have their own menus or title lists. A title list (TOP MENU) usually contains titles of movies and songs recorded. On the other hand, a menu (MENU) usually contains various information about the disc and playback selections.
When using the number buttons on the remote controller • To select number 5, press 5. • To select number 10, press 10. • To select number 23, press +10, +10, then 3. ○○○○○○○○○ Zooming in To cancel the PBC playback You can zoom into a particular portion of the picture. • This function is only possible using the remote controller. You can cancel the menu-driven operations (PBC function) using the remote controller. 1 1 Press 7 to stop playback. 2 Press number buttons to select a track.
○ ○ ○ ○ ○ ○ ○ ○ ○ Selecting ○ ○ ○audio○languages ○○○○○ Selecting subtitles While playing a chapter containing subtitles in different languages, you can select the subtitle language to display on the monitor. • You can also select the subtitle language using SETUP menu (see page 44). For DVD: While playing a chapter containing audio languages, you can select the language to listen to. • You can also select the audio language using SETUP menu (see page 44).
○○○○○○○○○ When playing VCD: Selecting multi-angle views While playing a disc containing multi-angle views, you can view the same scene at different angles. 1 STEREO LEFT RIGHT 2 Select a view angle you want. • STEREO: To listen to normal stereo (left/ right) playback. • LEFT: To listen to the left audio channel. • RIGHT: To listen to the right audio channel. Ex. 1/3 2/3 28 25-30_KD-AV7008[A]f.
○○○○○○○○○ ○list○ ○ ○ ○ ○ ○ ○ ○ the Locating a folder/track using To locate a folder by displaying the folder list • This functions only for MP3. 1 To locate a track by displaying the track list 1 2 2 3 Select a track you want. Current folder name or ID3 Tag (for MP3) Disc name (for CD) or CD Text 3 Select a folder you want. Current track name or ID3 Tag To next/previous page of the list Ex. when playing MP3 To next/previous page of the list 29 25-30_KD-AV7008[A]f.
○ ○ ○ ○ ○ ○ ○ ○ ○ Selecting ○ ○ ○playback ○ ○modes ○○○○ ○○○○○○○○○ information Displaying the disc text With Auto Scroll or Scroll selected, you can display the text and scroll it on the monitor if it is long and cannot be displayed at a time. 1 You can use only one of the following playback modes at a time—Repeat Play, Random Play, and Intro Scan. • For VCD: While PBC is not in use. Repeat Play You can repeat playback. • Repeat Play can be deactivated only for DVD.
Random Play You can play back tracks at random. 2 1 When playing VCD/CD: INTRO SCAN TRACK 2 INTRO SCAN OFF When playing MP3: INTRO SCAN TRACK INTRO SCAN FOLDER INTRO SCAN OFF When playing VCD/CD: RANDOM PLAY DISC RANDOM PLAY OFF INTRO SCAN • TRACK: Plays the beginning of all tracks. • FOLDER: Plays the first tracks of all folders. • OFF: Cancels Intro Scan.
3 3 Enter a number, then confirm. Ex. when playing DVD: Enter a number, then confirm. Ex. when playing DVD: Clear the entry. Confirm Clear the entry. Confirm Ex. when playing CD: When using the number buttons on the remote controller • To select number 5, press 5. • To select number 10, press 10. • To select number 23, press +10, +10, then 3. You cannot select folder using the remote controller. Examples (for DVD) To play back from 2(H):34(M):00(S) Press number buttons 2, 3, 4, then ENTER.
Dual Mode Operations You can play back two different sources as the main source (MAIN) and subsidiary source (SUB). You can listen to the main source through the speakers, while the subsidiary source through the monitor inserted into the cradle or the one connected to the AV OUTPUT jacks. • For connections of the cradle and an optional monitor, refer to the Installation/ Connection Manual (separate volume).
○○○○○○○○○ Adjusting AV OUTPUT volume Select an appropriate volume level for the component connected to the AV OUTPUT jacks on the hideaway unit. • This functions without respect to the Dual Mode setting. 1 When using the remote controller: • For Dual Mode operations... – When controlling the monitor connected to the AV OUTPUT jacks, aim the remote controller at the remote sensor on the main unit.
Surround Mode Operations 1 2 *2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 Activate and select the surround mode or DSP mode. *2 See page 41. See page 41. See page 34. See page 39. 4 Make adjustment if you want to. • If neither surround mode nor DSP mode is activated, you cannot make adjustment. When surround mode is activated: When DSP mode is activated: 35 35-38_KD-AV7008[A]f.
○○○○○○○○○ Introducing surround/DSP mode Surround modes Dolby Digital Dolby Digital is a digital signal compression method, developed by Dolby Laboratories, and enables multi-channel encoding and decoding (1ch up to 5.1ch). Dolby Digital 5.1 CH Dolby Digital 5.1 CH encoding method records and digitally compresses the left front channel, right front channel, center channel, left surround channel, right surround channel, and LFE channel signals (total 6 channels, but the LFE channel is counted as 0.
○○○○○○○○○3 ○ mode ○○○○○○○○ DSP Turning on and off the surround/ You can use surround or Digital Signal Processor (DSP) mode while playing any source. However, when playing a multi-channel encoded disc, you cannot apply DSP mode to the playback sounds. • When “AUTO SURROUND” is set to “ON” (initial setting when shipped from factory), an appropriate surround mode is automatically selected without any setting operation (see page 50).
4 Adjust the selected surround or DSP mode. When DSP mode is activated: When surround mode is activated: Ex. When selecting “HALL.” 1 Select one of the DSP modes. HALL: Reproduces the spatial feeling of a large shoeboxshaped hall designed primarily for classical concerts. : Selected automatically when multichannel DTS signal is detected (while playing a DVD or a DTS CD). No further adjustment is allowed. : Selected automatically when multichannel Dolby Digital signal is detected (while playing a DVD).
Sound Modes (iEQ) Operations The following operations are only possible for the main source when using Dual Mode. 1 *2 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 See page 35. See page 35. See page 41. See page 41. See page 34. 4 Select one of the preset sound (iEQ) modes (then make adjustment if you want to make your own sound mode). Select sound modes. Adjust the level of each frequency band. Display the other set of the sound modes.
○ ○your○own○ sound ○ ○modes ○○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Storing Selecting preset sound modes You can select a sound mode suitable to the music genre. Available sound modes: • HARD ROCK / R&B / POP / JAZZ / DANCE / COUNTRY / REGGAE / CLASSIC • USER1 / USER2 / USER3 • FLAT (To cancel the sound mode) You can adjust the sound modes and store your own adjustments in memory. 1 Repeat steps 1 to 4 on the left column to select a sound mode you want to adjust. 2 Make adjustments as you like.
Other Sound Adjustments Fader/Balance adjustments is only possible for the main source when using Dual Mode. 1 *2 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *1 3 See page 35. See page 35. See page 34. See page 39. 4 Make adjustment as you like. To adjust the input level This setting is required for each source except FM. Once you have made an adjustment, the volume level will automatically changes by adjusted level whenever you change the source.
Monitor Adjustments When no playback picture from the source is displayed, you can only adjust the brightness. 1 Display SCREEN CONTROL screen. Hold Adjustable items Hold ASPECT On the remote controller On the main unit 2 : Indicates the current ambient light level. As this level changes, the monitor adjusts the brightness automatically to match it to the current ambient light level. Select an item to adjust. : Adjust the brightness separately for day ) and night time ( )—(LIGHT/ time ( DARK).
Initial Setup—DVD MENU You can preset the initial disc playback conditions. • While playing, no change can be made on the DVD Menu. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. 5 Change the setting. • For details, see the following pages. Ex. When setting “MONITOR TYPE.” 43 43-48_KD-AV7008[A]f.
MENU LANGUAGE Select the menu language. MONITOR TYPE Select the monitor type of your TV (connected to the AV OUTPUT jacks) to play DVD Video recorded with aspect ratio of 16:9. • For the removable monitor of this unit, set this to “16:9 AUTO.” • 16:9 NORMAL: Select when the aspect ratio of your TV is fixed to 16:9 (wide TV). • 16:9 AUTO: Select when the aspect ratio of your TV is 16:9 (wide TV), and it is equipped with aspect ratio adjustment function. AUDIO LANGUAGE Select the audio language.
Initial Setup—MONITOR You can preset the initial monitor conditions. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. 5 Change the setting. • For details, see the following pages. Ex. When setting “BEEP TONE” to “OFF.” 45 43-48_KD-AV7008[A]f.
AUTO OPEN/CLOSE BEEP TONE • AUTO: The monitor comes out* or goes in automatically when you turn on or off the power. • OFF: Cancels this function. • ON: * If you close the monitor before turning off the power, the monitor will not come out next time you turn on the power. WIRING CHECK You can confirm the wiring connection is correctly done for particular functions. Touch tone beeps when you touch the Touch Panel icon. • OFF: Cancels this function.
Initial Setup—ON SCREEN You can preset the initial on-screen conditions. 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. Language selection screen appears. 5 Change the setting. • For details, see the following pages. Ex. When setting “CLOCK” to “OFF.” 47 43-48_KD-AV7008[A]f.
ON SCREEN LANGUAGE You can select the language for this Setup Menu and some of the messages displayed on the monitor. MESSAGE • ON: Speaker/signal indicators (see page 69) and messages are displayed. Messages are displayed on the viewing window of the monitor screen... – When selecting repeat mode, random mode, intro scan, etc. – When starting Time Search, Title Search, Chapter Search, and Track Search. GUIDE Ex. One of the messages appears when selecting repeat mode.
Initial Setup—AUDIO MENU/PSM You can preset the initial audio-related conditions and Preferred Setting Modes (PSM). • You cannot select “AUDIO MENU” when the subsidiary source operation screen is displayed on the monitor (with Dual Mode turned on; see page 33). 1 2 *1 It does not appear for some sources. *2 It will be shaded when not available. *1 *2 *1 3 See page 13. 4 Select the item you want. Appears when TV tuner unit KV-C1008 is connected. 5 Change the setting or enter the setting screen.
AUTO SURROUND You can activate an appropriate surround mode automatically when a loaded disc is detected. • ON: An appropriate surround/DSP mode is automatically selected. • • • • • FRONT LEFT: FRONT RIGHT: ALL CENTER: REAR CENTER: For the front left seat. For the front right seat. For all front and rear seats. For the rear seats. : Displays the SPK DISTANCE screen. You can adjust the speaker distance from your listening position in meters or feet.
D (Dynamic). RANGE COMPRESSION You can enjoy a powerful sound even at a low volume level by compressing dynamic range (difference between the lowest and the highest frequency sounds). • This takes effect for all the playback sources. • SUBWOOFER: Select “YES” (connected) or “NO” (disconnected). • SUBWOOFER PHASE: Select either “NORMAL” or “REV. (reverse)” to obtain better subwoofer sounds.
AV2 INPUT SELECT You can determine the use of AV INPUT 2 jacks on the hideaway unit—select either “VIDEO” or “CAMERA.” • When the playback source is “AV2,” this setting cannot be changed. • VIDEO: The source “AV2” works for viewing the playback picture through the component connected to the AV INPUT 2 jacks. • CAMERA: Select this when connecting the rear view camera. – You can set the remaining two items (BACK GEAR/ CAMERA VIEW).
Other Main Functions ○○○○○○○○○○○○○○○○○○ Assigning titles to the sources Roman alphabet list Alternates between upper and lower cases. Backspace (Erase the last entry.) Moves the cursor position. Upper cases Erase all entered character. Lower cases Confirm the entered name. Accented characters: Upper cases Display the other page of the character list of the same type. Entered name is displayed. Alternates between Roman alphabet and accented letter lists.
You can assign titles to 30 FM/AM, 30 TV stations, and 40 CDs (both in this unit and in the CD changer). Source Maximum character number Stations: 10 CDs: 32 If the “DELETE DISC NAME” or “DELETE STATION NAME” screen appears The internal memory is full. Delete unwanted names before assignment. • You cannot assign a title to CD Text and MP3 discs. • If you change the “TV CHANNEL AREA” setting (see page 52), assigned TV station names are all erased. Ex. When trying a name to a 41st disc.
○○○○○○○○○ ○○○○○○○○○ angle Changing the monitor position/ You can change the monitor position and the monitor angle. • Once you change them, they are stored. The monitor opens at the stored position and angle, next time you eject the monitor. To operate the car switches behind the monitor, press OPEN once. The monitor change its angle to the illustrated position for about 30 seconds. To return to its previous angle within 30 seconds, press OPEN again.
CD Changer Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current disc/folder/track no. Elapsed playing time Playback mode Sound mode (see page 39) Surround/DSP mode (see page 36) Volume level appears when adjusted. Disc text/ID3 tag information area Only for MP3 CD/CD Text MP3 Only for CD: See page 53. See page 14. See page 14. See page 15. See page 39. See pages 43 – 52. Back to the beginning 56 56-61_KD-AV7008[A]f.
Basic CD Changer Operations 2 Operate the disc 1 Select “CD-CH” : Selects the disc. then : Selects the folder (only for MP3). : Goes back to the beginning of the current track, then skips to the previous tracks if pressed repeatedly. : Skips to the following tracks if pressed repeatedly. Ex. While playing CD/CD Text* * Disc text information recorded in the CD Text can be displayed when a JVC CD Text compatible CD changer is connected. Ex.
Advanced CD Changer Operations ○○○○○○○○○3 Selecting disc/folders/tracks Select a disc you want. You can select the disc, (folder: only for MP3,) and tracks using the buttons on the main unit. 1 DISC FOLDER TRACK 2 To next/previous page of the list Disc names will be shown once it is recognized. When using the remote controller You can directly select the disc number by pressing the corresponding number buttons (1 – 12).
3 ○○○○○○○○○ ○○○○○○○○○ information Displaying the disc text Select a folder you want. Current track name or ID3 Tag With Auto Scroll or Scroll selected, you can display the text and scroll it on the monitor if it is long and cannot be displayed at a time. 1 To next/previous page of the list 2 (For CD) (For MP3) Shaded when no MP3 files are included. You cannot select this folder. Auto Scroll Scroll Off To locate a track by displaying the track list Example: while playing MP3.
○○○○○○○○○ Selecting playback modes You can use only one of the following playback modes at a time—Repeat Play, Random Play, and Intro Scan. Repeat Play You can repeat playback. • Repeat Play cannot be deactivated. Random Play You can play back tracks at random.
Intro Scan You can play back the first 15 seconds of each track sequentially. 1 Only for MP3 2 ○○○○○○○○○ Searching for songs You can use search functions to find your favorite tracks (for CD/MP3) and folders (for MP3). Folder/Track Search You can select a specific track (for CD/MP3) or folder (for MP3).
External Component Operations You can connect two video components as the playback components and an optional TV tuner unit (KV-C1008). • When you connect the video camera as a rear view camera to the AV INPUT 2 jacks to guide you to back the car, set the usage of the AV INPUT 2 jacks correctly (see page 52). • For connections, see the Installation/ Connection Manual (separate volume).
TV Tuner Operations Dual Mode indicator (see page 33) SOURCE icon (see pages 14 and 33) Current preset no. Channel no. Search mode Sound mode (see page 39) Surround/DSP mode (see page 36) Volume level appears when adjusted. Playback picture will be shown in the picture view window. Available only after pressing “M” (next to this icon). See page 53. See page 14. See page 14. See page 15. (Not available while viewing the playback picture.) See page 39. See pages 43 – 52.
○ ○ ○ ○ ○ ○ ○ ○ ○ 3 Tune in to a TV station Watching TV programs Before watching TV, select the area where you use the optional TV tuner unit (KV-C1008)— see page 52. • To tune in to a station using Preset Search, first store your favorite TV stations into memory (12 stations). • For Auto Search, press either icon once. “Auto Search” begins. When a station is received, searching stops. • For Manual Search, press either icon repeatedly (or hold) until a station you want is selected.
To tune in to a preset station • See also “Watching TV programs” on page 64. Manual presetting 1 Tune in to a TV station. 1 then Select “MANUAL” (or “AUTO”). 2 2 Select a preset number. Store the station into a preset number. To select the rest of the preset stations then To select the rest of the preset stations Preset station information will be displayed. 65 62-66_KD-AV7008[A]f.
○○○○○○○○○ Displaying the preset list You can store and select the preset station using the preset list on the monitor screen. To store a station using the preset list 1 Tune into a TV station. Select “MANUAL” (or “AUTO”). To select a preset station using the preset list then 1 2 2 3 Store the station into a preset number. To next/previous page of the list • Preset numbers, channel numbers and assigned names (see page 53) of the preset TV stations are shown on the list.
Maintenance How to clean the monitor When removing stains or dust on the surface, turn off the monitor, then wipe with dry soft cloth. • Be careful not to scratch the surface when wiping it. • Do not use the following materials to clean the monitor: – Wet cloth – Volatile substance such as benzine and thinner – Acid detergent, alkaline detergent, and detergent composed of organic substance • When using chemically processed duster, read its precautions carefully.
More about This Receiver ○ ○ ○ ○ ○ ○ ○ ○ ○ Basic ○ ○Disc○Operations ○○○○○○ Operation Methods • Touch Panel screen goes off if no operations are made on it for about 30 seconds while viewing the playback picture. ○○○○○○○○○ Basic Operations Turning on the power General • In this manual, words “track” and “file” are interchangeably used when referring to MP3 files and their file names. • When a disc has been already loaded, selecting “DISC” for the playback source starts disc play.
• The speaker/signal indicators appear in the following cases (only for DVD/CD): – When a different type of the digital signal is detected, or – When you start playback or resume playback from pause. Speaker indicators Signal indicators Ejecting a disc • If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to prevent it from dust. (Disc will not play this time.
Notes on MP3 files • This unit can play back MP3 files only with the extension code <.mp3> (regardless of the letter case—upper/lower). • This unit cannot play back the files encoded in the following formats—MP3i, MP3 PRO, Layer 1, Layer 2 format. • This unit can show the names of albums, artists (performer), and tracks of ID3 Tag (Version 1.0 and 1.1). • This unit can show up to 64 characters on the monitor screen. • This unit can handle only one-byte characters.
○○○○○○○○○ Sound Mode (iEQ) Operations • If you do not want to store your current adjustment, but only to apply the adjustment to the current playback source, press RETURN on the monitor screen to go back to the operation screen of the current source. Adjustment you made remains effective until you select a sound mode. MONITOR TYPE • When you select “16:9 NORMAL” for a picture whose aspect ratio is 4:3, the picture slightly changes due to the process for converting the picture width.
Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. General • Sound is sometimes interrupted. ] You are driving on rough roads. Stop playback while driving on rough roads. ] Disc is scratched. • Sound cannot be heard from the speakers. ] Connections are incorrect. • No sound comes out of the subwoofer (though it is activated—set to “YES”).
• Noise is generated. ] The current track is not an MP3 file (although it has the extension code— <.mp3>). • Elapsed playing time is not correct. ] This sometimes occurs during play. This is caused by how the tracks are recorded on the disc. • Correct characters are not displayed. ] This unit can only display a limited number of special characters (see the tables on page 53). Initial setup—AUDIO MENU/PSM • “SPEAKER SIZE” settings change. ] Speaker size settings are very much related to one another.
Additional Information Preset iEQ mode The table below shows the preset frequency level settings for each iEQ mode.
LANGUAGE CODES Code Language Code Language Code Language AA AB AF AM AR AS AY AZ BA BE BG BH BI BN BO BR CA CO CS CY DA DZ EL EO ET EU FA FI FJ FO FY GA GD GL GN GU HA HI HR HU HY IA IE IK IN IS IW JI JW Afar Abkhazian Afrikaans Ameharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish Bhutani Greek Esperanto Estonian Basque Persian Finnish Fiji Faroese Frisian Irish Scots Gaelic Galician Guarani Gujara
Specifications ○○○○○○○○○ Main unit AUDIO AMPLIFIER SECTION Maximum Power Output: Front: 50 W per channel Rear: 50 W per channel Center: 35 W Continuous Power Output (RMS): Front: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Rear: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Center: 15 W into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion.
Dimensions (W × H × D): Installation Size: • With sleeve-mounting plate Type B (standard) 182 mm × 52 mm × 165 mm • With sleeve-mounting plate Type A 182 mm × 52 mm × 160 mm Panel Size: 188 mm × 58 mm × 14 mm Mass: 2.25 kg (including monitor) Required space for the monitor ejection 177 143.3 15 12.2 ○○○○○○○○○ Hideaway unit Input Terminals: AV INPUT 1/2: Audio: 0.5 Vrms (Left/Right) Video (composite): 1 Vp-p/75 Ω Output Terminals (Level/Impedance): AV OUTPUT: Audio: 2.
Having TROUBLE with operation? Please reset your unit. Refer to page of How to reset your unit. EN © 2004 Victor Company of Japan, Limited Cover_KD-AV7008[A]f.
KD-AV7008 Installation/Connection Manual 1004MNMMDWJEIN EN LVT1174-002A [A] © 2004 Victor Company of Japan, Limited This unit is designed to operate only on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
SYSTEM CONNECTIONS • For A , B , C , D , E , F , more information are given on the following pages. F D B (KV-C1008) A POWER REMOTE SENSOR VIDEO AV OUTPUT 3 2 TV ANTENNA TV tuner unit R AUDIO L 4 C AV BUS TV TUNER UNIT KV-C1008 RESET B C E 1 A CD changer B A C CD changer (CH-X1500, etc.) VID EO TO CH AN GE Playback source R Camcorder, rear view camera, etc. VCR (KV-V8 or KZ-V10) Antenna cord from the car Use the extension antenna cord (supplied) if necessary.
ı Installing the hideaway unit (under the front seat) Tapping screws (not supplied) n • Be sure to use the tapping screws (not supplied) of appropriate length so that they will not damage any parts of the car. m Floor Ç Electrical connections Before connecting... • Make sure that the antenna cord from the car is connected to the hideaway unit (see page 2). If the antenna cord is not long enough, use the extension antenna cord (supplied). • Check the wiring in the car carefully.
D Connecting the cradle By using the cradle (KV-CR100), you can remove the monitor from the main unit and insert it into the cradle so that the persons sitting on the rear seat can view the playback picture even while the driver are driving your car. • The driver must not put on the headphones while driving. It is dangerous to shut off the outside sounds while driving. • Additional monitor (KV-MAV7001) can also be purchased to used so that you do not need to remove the monitor from the main unit.
KV-MAV7001 LVT1253-002A [A, E, EU, J] 7-inch Widescreen Detachable Monitor Abtrennbarer 7-Zoll Breitbild-Monitor Moniteur à écran large 7 pouces détachable Verwijderbare 7-inch breedbeeld-monitor Monitor desmontable de pantalla ancha de 7 pulgadas Monitor widescreen staccabile da 7 pollici Bortagbar 7-tums widescreenmonitor 7-дюймовый съемный монитор INFORMATION (For U.S.A.
A B These buttons do not work when the monitor is installed into the cradle. Diese Tasten arbeiten nicht, wen der Monitor in die Halterung gesetzt ist. Ces touches ne fonctionnent pas quand le moniteur est installé sur le berceau. Deze toetsen werken niet wanneer de monitor in de bak is geplaatst. Estos botones no funcionan cuando el monitor se encuentra instalado en el cradle. Questi pulsanti non funzionano se il monitor si trova nel supporto.
KV-MAV7002 LVT1253-003A [U] 7-inch Widescreen Detachable Monitor : Instructions Monitor desmontable de pantalla ancha de 7 pulgadas : Manual de instrucciones Moniteur à écran large 7 pouces détachable : Manuel d’instructions 0904MNMMDWJEIN EN, SP, FR, CT, TH © 2004 Victor Company of Japan, Limited English Español Français Thank you for purchasing a JVC product.
‰∑¬ !" JVC !"#$%&'()*+,#$-.