VIDEO CASSETTE RECORDER HR-S4800U HR-S3800U CABLE/ DBS TV MBR SET A/B POWER TV/VCR A. MONITOR DISPLAY 1 2 3 2 4 5 6 DBS DAILY(M-F) WEEKLY 7 8 9 C.
EN Dear Customer, Thank you for purchasing the JVC S-VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new VCR. CAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EN IMPORTANT PRODUCT SAFETY INSTRUCTIONS Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing. 3 5. Ventilation Slots and openings in the cabinet are provided for ventilation.
EN USE SERVICING 1. Accessories 1. Servicing To avoid personal injury: • Do not place this product on an unstable cart, stand, tripod, bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product. • Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product. • Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.
EN CONTENTS I I NSTALLING YOUR NEW VCR 6 Basic Connections .................................. 6 NITIAL SETTINGS 8 Plug & Play Setting ....................................... 8 Language Setting .......................................... 9 Clock Setting ............................................... 10 Preparations ...................................................... 10 Setting clock semiautomatically — Semiauto Clock Set ......................................
EN INSTALLING YOUR NEW VCR Basic Connections ANTENNA IN (Antenna or cable input) Antenna or cable Coaxial cable Flat feeder VIDEO OUT Matching transformer (not supplied) AUDIO OUT AC Power Cord REMOTE PAUSE/ AV COMPU -LINK CABLE BOX S IN AUDIO OUT V I D E O Back of VCR VIDEO CH3 CH4 S VIDEO OUT S-video cable (supplied) To S-video input connector Audio/video cable (supplied) To Audio/video input connectors RF cable (supplied) To 75 ohm terminal TV 6 OUT ANTENNA IN R L VHF/UHF TV O
EN 1 2 3 Check contents Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (Z pg. 62). Situate VCR Place the VCR on a stable, horizontal surface. Connect VCR to TV The following connections are required. 5 7 Final preparation for use Turn on the VCR and set the CH3-CH4 switch on the rear (shown below) to either CH3 or CH4 correctly. c The CH3–CH4 switch is preset to the CH3 position. Set to CH4 if CH3 is used for broadcasting in your area.
EN INITIAL SETTINGS Plug & Play Setting Auto Clock Set/Auto Tuner Set ATTENTION c If you use a cable box, Plug & Play will not function; set the clock and tuner channels separately. (Z pg.10 – 14) c It takes several minutes for the VCR to complete the Plug & Play setting. c Do not press any buttons on the front panel or on the Remote while Plug & Play is in progress. FF REW POWER MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R S-VHS ET SP EP VCR CH OK During Initial Auto Clock Set “Auto” blinks.
EN Language Setting This VCR offers you the language choice to view menus and some messages (excluding the on-screen display superimposed on the TV screen) — in English, Spanish or French. Select the desired language using the following procedure. The default setting is “ENGLISH”. 1 2 Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.
EN INITIAL SETTINGS (cont.) Clock Setting Perform clock setting only if the clock has not been set correctly by the Plug & Play setting or if you use a cable box. Access the Clock Set screen to perform the Semiauto or Manual Clock Set. Each procedure starts from step 4 after preparation steps below are finished. If you use a cable box, set the clock manually. (Z pg. 12) Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.
EN Setting clock semiautomatically — Semiauto Clock Set 6 You can change the host channel/D.S.T. /time zone setting manually. First follow steps 1 to 3 on page 10, then go to the following steps. 4 Set Auto Clock to ON On the front panel: Press OK to move the highlight bar to “AUTO CLOCK”, then press CH5∞ so that “ON” is selected. CLOCK SET You have three choices: AUTO– Select if you want to adjust your VCR’s clock automatically by the incoming signal from the host channel.
EN INITIAL SETTINGS (cont.) 4 – 7 8 5 POWER MENU PLAY S-VIDEO c Holding CH 5∞ or SHUTTLE PLUS %fi changes the date in 15-day intervals. VIDEO (MONO)L—AUDIO—R S-VHS ET SP EP VCR CH OK REC STOP/EJECT PAUSE 4 – 7 6 Set year On the front panel: Press CH5∞ until the desired year appears, then press OK twice. On the Remote: Press SHUTTLE PLUS %fi until the desired year appears, then press OK or SHUTTLE PLUS # twice.
EN Tuner Setting Setting channels automatically — Auto Channel Set Use Auto Channel Set only if channels have not been set correctly by the Plug & Play setting. If you want to add or delete channels, use Manual Channel Set (Z pg. 14). Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. 1 2 2 3 1 4 FF REW POWER MENU PLAY S-VIDEO SP EP VCR CH OK REC STOP/EJECT PAUSE 2 3 3 1 2 3 4 5 6 7 8 9 Press MENU.
EN INITIAL SETTINGS (cont.) 2 – 4 1 5 2 MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R SP EP VCR S-VHS ET CH OK REC STOP/EJECT On the front panel: Press CH5∞ to move the highlight bar (arrow) to “TUNER SET”, then press OK. On the Remote: Press SHUTTLE PLUS %fi to move the highlight bar (arrow) to “TUNER SET”, then press OK or SHUTTLE PLUS #.
EN Cable Box Control Setting The following procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer recording. The Controller is effective for recording broadcasts that have been programmed using VCR Plus+ (Z pg. 30) or Express timer programing (Z pg. 34). NOTE: Suggested location Place the cable box on top of the VCR.
EN INITIAL SETTINGS (cont.) 2 3 Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. 3 4 6 2 POWER MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R SP EP VCR S-VHS ET CH OK REC STOP/EJECT 2 3 4 5 6 7 8 9 2 0 4 5 4 3 4 6 7 3 3– 5 Setting cable box output channel & brand After installation, set the cable box output’s channel and its brand correctly; otherwise, the Controller cannot work correctly.
EN 6 7 Access Cable Box Brand Set screen Press OK. Enter cable box brand On the Remote ONLY: Press the appropriate Number keys to enter the brand code from the list shown to the right, then press OK.
EN INITIAL SETTINGS (cont.) DBS Receiver Control Setting Suggested location Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver’s remote sensor. ATTENTION: The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the Controller so its signal reaches the remote sensors on both the DBS receiver and cable box.
EN 2 3 Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. 3 4 2 POWER MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R SP EP VCR S-VHS ET CH OK REC STOP/EJECT 2 3 4 5 6 7 8 9 4 5 4 1 2 3 4 3 3 – 5 Setting DBS receiver output channel & brand After installation, set the DBS receiver’s output channel and its brand correctly; otherwise, the Controller cannot work correctly.
EN INITIAL SETTINGS (cont.) 6 7 6 FF REW POWER MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R SP EP VCR S-VHS ET CH OK REC STOP/EJECT PAUSE Access DBS Receiver Brand Set screen Press OK. Enter DBS Receiver’s brand On the Remote ONLY: DBS RECEIVER BRAND SET Press the appropriate 40 Number keys to enter the brand code from the following list, then PRESS NUMBER KEY (0–9) press OK.
EN BASIC PLAYBACK AND RECORDING Basic Playback This VCR can check the tape condition during playback (and recording), and realizes the best possible pictures. 1 Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. FF REW POWER Load a cassette Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Do not apply too much pressure when inserting. c The VCR turns on automatically.
EN BASIC PLAYBACK AND RECORDING (cont.) Basic Playback Features A Press DISPLAY during playback. Each time you press the button, the front display panel shows the time counter, tape remaining time and the clock time in sequence.
EN D Adjusting tracking condition — Tracking Adjustments E 23 Selecting monitor sound — Audio Monitor Automatic tracking adjustment You can select the desired monitor sound. This VCR automatically adjusts the tracking condition. Whenever you insert a tape and start playback, automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback. While playing back a tape on which stereo sound or SAP sound is recorded, press A. MONITOR on the Remote.
EN BASIC PLAYBACK AND RECORDING (cont.) G H FF REW POWER MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R SP EP VCR S-VHS ET CH OK REC STOP/EJECT PAUSE Index codes are placed on the tape at the beginning of each recording when recording on this VCR. You can find and automatically play back from the beginning of any recording using the Index Search function. 1 2 2 3 4 5 6 7 8 9 2 0 Start search While the tape is not running, press SHUTTLE PLUS 4 or ¢ on the Remote.
EN Basic Recording 2 PLAY ( 3 ) 4 FF REW MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R SP EP VCR S-VHS ET CH OK 2 REC STOP/EJECT PAUSE STOP/EJECT (7/0) PAUSE ( 8 ) POWER TV/VCR 1 2 3 4 5 6 7 8 9 2 0 2 –b Press SP/EP to set the recording speed. Start recording On the front panel: Press REC ( ¶ ). On the Remote: While holding REC ( ¶ ), press PLAY ( 3 ). c If “VIDEO CALIBRATION” is set to “ON” (default setting: Z pg.
EN BASIC PLAYBACK AND RECORDING (cont.) Basic Recording Features A Changing display information Press DISPLAY during recording or recording pause. Each time you press the button, the front display panel shows the time counter, channel number, tape remaining time and the clock time in in sequence.
EN D Showing on-screen display When “SUPERIMPOSE” is set to “ON” (Z pg. 38, 39), you can see the current VCR status on the TV screen. c For more detailed information about the on-screen display, see page 60. 1 Display VCR status on TV screen During recording or CH 125 RECORD THU 12:00 AM PAUSE recording pause, press STEREO ] SP SAP OSD. All indications + + + B E corresponding to the INDEX-1 NORM current VCR status are HI–FI COUNT –1:23:45 displayed for 5 seconds.
EN SPECIAL EFFECT PLAYBACK Special Effect Playback A 7 High-Speed Picture Search: A E PLAY ( 3 ) FF REW POWER MENU PLAY VIDEO (MONO)L—AUDIO—R SP EP VCR CH OK 1 2 REC STOP/EJECT PAUSE B D –1 On the Remote: ). To do forward picture search, press FF ( ). To do reverse picture search, press REW ( c If you press and hold the button for more than 2 seconds, simply releasing it cancels the picture search, and normal playback resumes. F To resume normal playback, press PLAY ( 3 ).
EN How to use the SHUTTLE PLUS buttons on the Remote: To do forward picture search, press SHUTTLE PLUS ¢ repeatedly. Each time you press the button, the search speed increases. c To decrease the speed while forward picture search (toward normal playback, then reverse picture search), press SHUTTLE PLUS 4 repeatedly. To do reverse picture search, press SHUTTLE PLUS 4 repeatedly. Each time you press the button, the search speed increases while reverse picture search.
EN TIMER RECORDING VCR Plus+ Timer Programing ® Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. Timer recording allows you to program the VCR to automatically record a broadcast at some future time. Up to 8 timer recording programs can be made using VCR Plus+ timer programing or Express timer programing method (Z pg. 34) as far as a year in advance.
EN 4 5 Input receiving channel number The guide channel GUIDE CHANNEL SET number, which is GUIDE CH: 12 assigned to the TV or VCR CH : – – – cable station for the PlusCode number that PRESS NUMBER KEY (0–9) you entered in step 3, OR (5,∞), THEN (OK) PRESS (PROG.) TO END will appear automatically on the Guide Channel Set screen.
EN TIMER RECORDING (cont.) Changing VCR Plus+ Setting IMPORTANT If you have moved to a different area or if a broadcasting station’s channel number has been changed, the wrong VCR CH or CABLE CH number will be displayed on the Program screen (Z step 5 on page 31). When this happens, perform the following steps to set the correct guide channel number for that station. To ensure that VCR Plus+ timer recording operates correctly, it is necessary to set the VCR Plus+ “Guide Channel Set” for each station.
EN 1 2 5 Access Main Menu screen Press MENU. Access Initial Set screen On the front panel: Press CH5∞ to move the highlight bar (arrow) to “INITIAL SET”, then press OK. MAIN MENU FUNCTION SET TUNER SET = INITIAL SET Input receiving channel number On the front panel: Press CH5∞ to select the number of the channel on which the guide channel’s broadcasts are received, then press OK.
EN TIMER RECORDING (cont.) Express Timer Programing You can directly program the VCR’s timer to record up to 8 broadcasts, as far as a year in advance. Remember, the clock must be set before you can program the timer (Z pg. 8 or 10). 1 Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. Load a cassette Make sure the record safety tab is intact. If not, cover the hole with adhesive tape, then load it into the VCR.
EN 8 9 Set tape speed NOTES: Press SP/EP to set the tape speed. c Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time, channel settings, and other menu settings are lost if it lasts for more than 3 minutes. As a result, when the power is supplied again to this VCR after the power failure, the following will take place. 1. This VCR starts the Plug & Play setting automatically to restore the clock time and channel setting. 2.
EN TIMER RECORDING (cont.) A Checking program settings 1 Disengage timer Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. Press TIMER, then press POWER. c When “AUTO TIMER” (Z pg. 39) is set to “ON”, you do not have to press TIMER. A 1 2 3 4 5 6 7 8 9 2 –1 Access Program Check screen Press PROG. CHECK.
EN C When programs overlap each other If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking. PR START STOP CH DATE 1 8:00P 11:00 12 12/24 2 10:00A 10:45 40 12/25 3 11:30P 1:00 125 12/25 4 9:00P 10:00 10 12/24 5 6 7 8 (5,∞), THEN (>) (PROG.) : END PROGRAM NOT COMPLETED PROGRAM OVERLAP EX.
EN OTHER USEFUL FUNCTIONS Useful Function Settings You can use the other useful function settings on the Function Set screen by following the procedure described below. c For the functions you can set on the Function Set screen, see pages 39 to 42. 1 2 Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. 2 – 4 1 5 MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R SP EP VCR S-VHS ET CH OK REC STOP/EJECT PAUSE 3 2 3 Press MENU.
EN 39 * The default setting is bold in the table below. When this function is set to “ON”, this VCR checks the condition of the tape in use during playback and recording, and compensates to provide the highest-possible pictures. This takes place whenever you play back a tape or start recording after inserting a tape. m VIDEO CALIBRATION ON OFF NOTES: c During playback, this function is always working even though “VIDEO CALIBRATION” appears just at the beginning of automatic tracking.
EN OTHER USEFUL FUNCTIONS (cont.) * The default setting is bold in the table below. m AUTO SP = EP TIMER When this function is set to “ON”, the VCR automatically switches to EP mode to allow complete recording if there is not enough tape to record the entire program while timer-recording in SP mode. For Example . . .
EN 41 * The default setting is bold in the table below. m AUDIO MONITOR HI-FI: Normally select this. Hi-Fi sound is played back. HI-FI L: Sound on the left Hi-Fi channel is played back. HI-FI R: Sound on the right Hi-Fi channel is played back. NORM: Sound on the normal track is played back. MIX: Both sounds on the Hi-Fi track and normal track are mixed and played back. This VCR can record two sound tracks simultaneously (normal and HiFi) on a Hi-Fi stereo tape.
EN OTHER USEFUL FUNCTIONS (cont.) * The default setting is bold in the table below.
EN Child Lock You can disable the VCR operations. c You can only use the Remote for this operation. While the VCR is turned on, press and hold POWER on the Remote for more than seven seconds. The VCR turns off, and the child lock indicator appears on the front display panel. POWER 1 2 3 4 5 6 7 8 9 2 0 4 1 Child lock indicator c The child lock function is now activated and you cannot turn on the VCR by pressing POWER on the front panel.
EN EDITING Edit From Camcorder 4 5 6 FF REW POWER MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R SP EP VCR S-VHS ET CH REC OK STOP/EJECT Connection 3 4 5 This VCR (for recording ) FF REW POWER 8 MENU PLAY S-VIDEO VIDEO (MONO)L—AUDIO—R S-VHS ET SP EP VCR CH OK To AUDIO/ VIDEO Input Audio/video cable (supplied) REC STOP/EJECT PAUSE To rear panel REMOTE PAUSE/ AV COMPULINK connector 1 2 3 4 5 6 7 8 9 2 To S VIDEO Input Mini-plug cable (not supplied) (JVC camcorder only)
EN You can use a camcorder as the playback VCR and your VCR as the recording VCR 1 Make connections Connect an audio/video cable between the camcorder’s audio/video output connectors and your VCR’s audio/video input connectors. c When the JVC camcorder is equipped with the Master Edit Control, you can control the VCR from the camcorder. Connect the mini-plug cable (not supplied with this VCR) as illustrated to the left.
EN EDITING (cont.) Edit To Or From Another VCR 2 Load cassettes 3 Select input mode on recording VCR Ex. When using this VCR as the playback VCR This VCR (for playback) CABLE BOX S OUT V I D E O REMOTE PAUSE/ AV COMPU -LINK AUDIO VIDEO CH3 CH4 IN OUT On the front panel: Press CH5∞. ANTENNA IN R L VHF/UHF TV OUT On the Remote: Press the Number key "0 (AUX)" or CH +/–.
EN Audio Dubbing (ONLY FOR HR-S4800U) 2 Load a cassette and prepare the audio source 3 Select input mode Connection This VCR (for playback) FF REW POWER On the Remote: Press the Number key "0 (AUX)" or CH +/–. VIDEO (MONO)L—AUDIO—R S-VHS ET SP EP VCR CH OK To AUDIO IN REC STOP/EJECT PAUSE Audio cable (not supplied) 4 c Audio Dubbing is also possible using the audio input connectors on the rear panel.
EN EDITING (cont.) Insert Editing and AV Dubbing (ONLY FOR HR-S4800U) Insert Editing: You can replace a recorded scene with new scene recorded on another tape or with other material. Both the picture and the sound recorded on the Hi-Fi sound track are replaced at the same time. Audio/Video Dubbing: You can perform Audio Dubbing and Insert Editing at the same time. This means that the picture and the sounds recorded on the Hi-Fi sound track and on the normal track are replaced at the same time.
EN 1 Make connections 2 Prepare tapes 3 Connect an audio/video cable between the VCR’s audio/video input connectors and the other component’s audio/video output connectors. Load the source tape on the other VCR, and the tape to be edited on this VCR. Select editing function you want Set “EDIT FUNCTION” to either “INSERT” or “AV DUB” whichever you want to use by following the procedure described on pages 38 and 42. c Make sure to set “EDIT FUNCTION” to “RECPAUSE” after you finish editing tapes.
EN MULTI-BRAND REMOTE CONTROL TV Brand Setting This Remote can control some functions of remote controllable TVs listed below. Without setting, you can control a JVC TV. 2 2 –1 4 –2 1 Turn on the TV 2 Set TV brand code Turn on the TV using the Power button on the TV or its Remote. Follow the example shown below. 1 Press and hold TV. 2 Press MBR SET. 3 Press the Number keys to enter your TV’s brand code by referring to the table below. 4 Press OK, and release TV. The TV should turn off.
EN Cable Box Brand Setting 2 POWER –1 4 CABLE/DBS 2 –2 –3 1 2 3 4 5 6 2 9 Number 2 7 8 0 This Remote can control some functions of the cable boxes listed below. Some cable box brands have more than one code. If your cable box does not function with a specified code, try other codes. 1 Turn on the cable box 2 Enter cable box brand code 4 Turn on the cable box using the Power button on the cable box or its Remote. Follow the example shown below. 1 Press and hold CABLE/DBS.
EN MULTI-BRAND REMOTE CONTROL (cont.) DBS Receiver Brand Setting 2 This Remote can control some functions of the DBS (Direct Broadcast Satellite) receivers listed below. 1 Turn on the DBS receiver 2 Enter DBS receiver brand code POWER 2 –2 6 2 –3 9 Number –1 4 CABLE/DBS 1 2 3 4 5 2 7 8 0 3 3 2 –4 ENTER TV CH +/– Follow the example shown below. 1 Press and hold CABLE/DBS. 2 Press MBR SET.
EN Changing Remote Control Code 1 2 3 4 5 6 7 8 9 2 0 4 2 –1, 3 2 –2 53 This Remote is capable of transmitting two control codes; one set to respond to A code control signals and another set to respond to B code control signals. This Remote control is preset to send A code signals because your VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code signals.
EN Troubleshooting Before requesting service, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your VCR off for repair. POWER SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. The power will not come on. c The AC power cord is disconnected. Connect the AC power cord. 2. The clock works, but the VCR’s power will not come on.
EN 55 TIMER RECORDING POSSIBLE CAUSE SYMPTOM 1. Timer recording will not work. c The clock and/or the timer have been set incorrectly. c The timer is not engaged. c The VCR has not been set up properly. CORRECTIVE ACTION Set the clock and/or timer correctly. Press TIMER and check to make sure that ‰ appears on the front display panel. Re-perform the set-up procedures. Make sure you have compensated for guide channel and VCR or cable box channel number mismatches (Z pg. 32). 2.
EN TROUBLESHOOTING (cont.) OTHER PROBLEMS CORRECTIVE ACTION SYMPTOM POSSIBLE CAUSE 1. When scanning channels, some of them are skipped over. c Those channels have been preset to be skipped. If you need the skipped channels, restore them (Z pg. 14). 2. The channel cannot be changed. c Recording is in progress. Press PAUSE ( 8 ) to pause the recording, change channels, then press PLAY ( 3 ) to resume recording. 3. The Remote will not operate your TV or cable box or DBS receiver.
EN 57 Questions and answers PLAYBACK RECORDING Q. What happens if the tape reaches its end during playback or search? A. The VCR automatically rewinds it to the beginning. ............................................ Q. Can the VCR indefinitely remain in still mode? A. No. It stops automatically after 5 minutes to protect the heads. ............................................ Q. During picture search, still picture playback and frame-by-frame playback, the picture is intermittent. What’s the cause? A.
EN Index List of terms This guide serves as a quick way to locate frequently used terms and on-screen display names.
EN 59 Front panel 1 2 3 4 5 FF REW POWER MENU PLAY S VIDEO VIDEO (MONO)L—AUDIO—R SP EP VCR S-VHS ET CH OK 6 7 8 9 0 POWER button : Z pg. 21, 25 Cassette loading slot MENU button PLAY ( # ) button : Z pg. 21 SHUTTLE ring : Z pg. 21, 25, 28 S VIDEO input connector (ONLY FOR HR-S4800U): Z pg. 44, 48 7 AUDIO/VIDEO input connectors : Z pg. 47 8 S VHS ET button and lamp : Z pg. 27 1 2 3 4 5 6 @ ! # REC STOP/EJECT PAUSE $ % ^ 9 REVIEW button : Z pg.
EN INDEX (cont.) Rear panel 1 2 REMOTE PAUSE/ AV COMPU -LINK CABLE BOX S IN AUDIO OUT V I D E O VIDEO CH3 CH4 5 6 1 AC power cord : Z pg. 6 2 CABLE BOX Controller connector : Z pg. 15, 18 3 REMOTE PAUSE/AV COMPULINK terminal c REMOTE PAUSE terminal : Z pg. 41, 44 c AV COMPULINK terminal : Z pg. 41 4 ANTENNA IN terminal : Z pg. 6 5 6 7 8 9 0 4 3 IN OUT ANTENNA IN R R LL VHF/UHF TV OUT 7 8 9 0 S VIDEO IN connector : Z pg. 46 S VIDEO OUT connector : Z pg. 6 CH3-CH4 switch : Z pg.
EN Remote 1 2 3 4 MBR SET A/B POWER TV/VCR A. MONITOR DISPLAY 5 6 7 8 1 2 3 4 5 6 DBS DAILY(M-F) WEEKLY 7 8 9 C.
EN Specifications GENERAL Power requirement Power consumption Power on Power off Temperature Operating Storage Operating position Dimensions (W x H x D) TIMER : AC 120 V` , 60 Hz : 20 W : 2.5 W : 5°C to 40°C (41°F to 104°F) : –20°C to 60°C (–4°F to140°F) : Horizontal only : 400 x 94 x 281 mm (15-3/4" x 3-3/4" x 11-1/8") : 3.4 kg (7.5 lbs) : S-VHS/VHS NTSC standard Weight Format Maximum recording time SP : 210 min. with ST-210 video cassette EP : 630 min.
EN FOR SERVICING (Only in U.S.A.) 63 HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE: 1-800-252-5722 http://www.jvcservice.com Dear customer: In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the event that repair is necessary, or for the address nearest your location, please refer to the factory service center list below or within the Continental United States, call 1-800-252-5722 for your authorized servicer.
EN WARRANTY (Only in U.S.A.) LIMITED WARRANTY CONSUMER VIDEO 1-90 JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below.
EN MEMO (cont.) HR-S4800U/S3800U-EN54-68 65 00.1.
EN HR-S4800U/S3800U-EN54-68 66 00.1.
EN HR-S4800U/S3800U-EN54-68 67 00.1.
HR-S4800U/S3800U-EN54-68 68 COPYRIGHT © 2000 VICTOR COMPANY OF JAPAN, LTD. U/U(C) 00.1.