Model: DT-X93H 9” Full HD Broadcast LCD Monitor User Manual Ver: A Please read this User Manual throughout before using.
Preface 1. All internal technologies of this product are protected, including device, software and trademark. Reproduction in whole or in part without written permission is prohibited. 2. All brands and trademarks are protected and other relative trademarks in this user manual are the property of their respective owners. 3. Due to constant effort of product development, SWIT Electronics reserves the right to make changes and improvements to the product described in this manual without prior notice. 4.
Maintenance Warning 1. In order to reduce the risk of fire and electrical shock, do not lay this product in rain or damp places. 2. Please keep away from the strong magnetic field; it may cause the noise of the video and audio signals. The power 1. Please use the power adapter provided or recommended by the manufacturer in order to avoid damage. 2. For a third party power adapter, please make sure the voltage range, supplied power, and polarity of power lead are fit. 3.
Contents Preface..................................................................................................................................................... 2 Maintenance ............................................................................................................................................ 3 Contents................................................................................................................................................... 4 Installation Dimension ........
Installation Dimension The main body (in mm) 5
Operation Instructions ·Front Panel ⑴ Speaker: For SDI/HDMI embedded audio and analog audio monitoring. (Will not work if earphone is plugged in) ⑵ Button SOURCE: Press “SOURCE” to select SDI1, SDI2, HDMI, and CVBS signal input F1~F5: User definable function keys. Please see details in “4. Function key” under “Main Menu”. AUDIOBAR: Press “AUDIOBAR” to turn on or turn off the audio meters display. DISPLAY: Press “DISPLAY” to turn on or turn off relevant status information.
·OSD ⑴ Timecode(SDI) Under SDI input, it can display Timecode. If no Timecode information is detected, it will be displayed as “TC: UNLOCKED”. User can set function keys F1~F5 or GPI pins as “Timecode” to turn on or off this function. ⑵ UMD Set up the UMD under ‘UMD” submenu. ⑶ AFD (SDI) User can set function keys F1~F5 or GPI pins as “AFD” to turn on or off this function. If no relevant information is detected, it will be displayed as “AFD: UNLOCKED”. ⑷ Audio Monitor the audio information.
Introduction of audio and video functions 2-ch embedded audio meters Under SDI and HDMI input, it displays 2 channels embedded audio meters, and under analog input, the monitor displays 2 channels analog audio meters. The audio meter is green, and will turn yellow when audio exceeds -20dB, and turn red when audio exceeds -9dB. Audio alarm If the embedded audio value is too low or no audio input, it will display “MUTE” or “UNLOCKED” in the audio bar.
·Back Panel ⑴ TALLY Light: Red, Green and Yellow 3-color TALLY indicator. ⑵ DC IN: Connect with 4-pin XLR DC power adapter, support 6.5V-24V voltage input (Pin 1: Negative, Pin 4: Positive) ⑶ Battery mount connector The monitor has Gold mount plate pre-installed, and supplied an SSL-JVC50 battery plate in package for exchange. ⑷ Audio Socket AUDIO IN: 3.5mm analog audio input (CVBS) AUDIO OUT: 3.5mm audio output, to monitor SDI/HDMI embedded audio and analog audio.
Main Menu DT-X93H has OSD to adjust the parameters and settings, for example: Picture, color temp., function keys, etc. 1. Press “MENU/ENTER” button, the main menu will popup from the left top of the screen. The selected main menu highlights in yellow. 2. Revolve “MENU/ENTER” to select submenu, the selected submenu highlights in yellow, press “MENU/ENTER” to apply and enter into the selected submenu’s items. 3.
Sub-Menu (the default values are marked with underline) 1. Exit & Status Displays the current status, the details are as down below: *1 Display the current video signal and format *2 Display the current function keys setup 2. Picture To adjust picture parameters 3. Color Temp To select different color temperature or setup user-defined color parameters. * Only “Color Temp” is set to “User”, the Red/Blue/Green Gain or Red/Blue/Green Bias can be adjusted.
4. Function key To define the F1~F5 function keys. *1 Function keys F1-F5 can be set as the down below functions: Timecode, Zebra, Audio Bar, False Color, AFD, H/V Delay, R/G/B/Mono, Marker, Color Bar, UMD, Audio Alarm, Focus Assist, Aspect Ratio, Scan Mode, Zoom Mode, Mute, Freeze Frame, Flip, CVBS, HDMI , SDI1, SDI2 ,Color Temp. 5. GPI User can set GPI pins to relevant functions to turn on or off this function.
6. UMD Support “TSL UMD Protocol-V4.0” provided by Television System LTD Source ID Setup: Select “Source ID”, revolve “MENU/ENTER” to select the letters and press “MENU/ENTER" to input. Max 8 letters are supported. Select “Exit” to quit and save settings, the source ID will be displayed on top or bottom of the screen.
8. Audio *1 When “Bar Frame” is set to “Off”, only the audio meter will be displayed. When “Bar Frame” is set to “On”, frame and real-time audio value will be displayed. *2 When “Audio Alarm” is set to “On”, if no embedded audio is detected, the audio bar will display “UNLOCKED”. If the audio value is too low, the audio bar will display “MUTE”. *3 Select Channel Under SDI signal, user can set output audio from channel 1 or channel 2 9.
10. System *1 Source Scan When set to “Yes”, after turn on the monitor, the signal will be inspected and follow the sequence of “SDI1→SDI2→HDMI→CVBS”. For example: if channel is selected to SDI2, SDI-IN2 has no input, and CVBS has input. When turn on the monitor, after automatic inspection, SDI2 has no recognized signal, and CVBS has recognized signal, then the input signal will be CVBS. When set to “No”, update model will not be supported. *2 Logo When powered on, the screen will display ProHD logo.
13. OSD 14. Key Inhibit If the “Key Inhibit” is “On”, there is no response when all the buttons expert ” MENU/ENTER” are pressed, the sreen will be displayed as ” Key Inhibit”.
Specification LCD Performance Size Display area Resolution Color Aspect ratio Brightness Contrast Viewing Angle Input/output Input Output BNC×2 BNC×1 HDMI×1 GPI×1 USB×1 3.5mm×1 BNC×2 BNC×1 HDMI×1 3.5mm×1 Video Format CVBS HDMI SMPTE-2048-2 SMPTE-425M-A/B SDI General SMPTE-274M SMPTE-RP211 SMPTE-296M SMPTE-125M ITU-R BT.656 Input voltage Power consumption Working temperature Working humidity Storage temperature Storage humidity Dimensions Net weight (main body) 9 inches 191.5×119.
Trouble-shooting Symptom Possible Causes The power is not turned on No display Reconnect to power supply The attached battery is no power Change battery Bad contact of BNC or HDMI cable Change cable BNC or HDMI cable loose contact or not correctly connected Check and correctly connect the BNC or HDMI cable Refer to the provided power supply, reconnect the power.
This model is manufactured, warranted and supported by SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC, and distributed in North America by JVCKENWOOD USA Corporation.. To obtain service or for further information, please contact: SWIT Electronics USA, LLC. Address: 3350 Scott Blvd. 61-02, Santa Clara, CA 95054 Toll free: 1 866 986-SWIT (7948) • Tel: 408 260-8258·Fax: 408 228-8438 Email: info@swit.us • Website: www.swit.