Model: DT-X73F 7” Full HD Camera-top LCD Monitor User Manual Ver: A Please read this User Manual throughout before using.
Preface 1. All internal technologies of this product are protected, including device, software and trademark. Reproduction in whole or in part without written permission is prohibited. 2. All brands and trademarks are protected and other relative trademarks in this user manual are the property of their respective owners. 3. Due to constant effort of product development, SWIT Electronics reserves the right to make changes and improvements to the product described in this manual without prior notice. 4.
Maintenance Warning 1. In order to reduce the risk of fire and electrical shock, do not lay this product in rain or damp places. 2. Please keep away from the strong magnetic field; it may cause the noise of the video and audio signals. The power 1. Please use the power adapter provided or recommended by the manufacturer in order to avoid damage. 2. For a third party power adapter, please make sure the voltage range, supplied power, and polarity of power lead are fit. 3.
Contents Preface ..................................................................................................................................................................2 Maintenance .........................................................................................................................................................3 Contents ...........................................................................................................................................................
Dimension The main body (mm) Sun hood installation ⑴ Take out the sun hood from the flannel bag, see pic1; ⑵ Push out the sun hood as pic2, unfold as pic3; ⑶ Fold the two bottom parts inward as pic3, with the internal magnets attached and fixed as pic4; ⑷ Install the sun hood on the monitor, see as pic5.
Operation Instructions ⑴ SOURCE: Input signal source selection F1 – F4: User definable function keys User can set F1, F2, F3, F4 keys to corresponding function for quick operation. For details please refer to “Sub Menu - 4.Function key”. When user press and hold the function keys for more than 3 seconds, it will pop-up a definable function list menu, user can rotate and press to select functions. If no operation exceeds 3 seconds, the monitor will automatically save the selection and Exit.
·OSD ⑴ Timecode (SDI) Under SDI input, it can display Timecode. If no Timecode information is detected, it will be displayed as “TC: UNLOCKED”. User can set function keys F1 - F4 as “Timecode” to turn on or off this function ⑵ UMD Display the source title. Set up under “UMD” submenu. ⑶ AFD (SDI) User can set function keys F1 - F4 as “AFD” to turn on or off this function. If no relevant information is detected, it will be displayed as “AFD: UNLOCKED”.
Introduction of audio and video functions 16-ch embedded audio meters The monitor can display max 16 channels audio meters for SDI embedded audio, max 8 channels meters for HDMI embedded audio, and 2 channels meters for analog audio. The audio meter is green, and will turn yellow when audio exceeds -20dB, and turn red when audio exceeds -9dB.
Main menu DT-X73F has OSD to adjust the parameters and settings, for example: Picture, color temp., function keys, etc. 1. Press “MENU” button, the main menu will pop-up from the left top of the screen. The selected main menu highlights in yellow. 2. Revolve “MENU” to select submenu, the selected submenu highlights in yellow, press “MENU” to apply and enter into the selected submenu’s items. 3.
Sub-Menu (the default values are marked with underline) 1. Exit & Status Displays the current status, the details are as down below: *1 Display the current video signal and format *2 Display the current function keys setup 2. Picture To adjust picture parameters 3. Color Temp To select different color temperature or setup user-defined color parameters * Only “Color Temp” is set to “User”, the Red/Blue/Green Gain or Red/Blue/Green Bias can be adjusted.
4. Function key To define the F1 – F4 function keys *1 Function keys F1 – F4 can be set as the down below functions: Audio Bar, Histogram, False Color, AFD, H/V Delay, R/G/B/Mono, Marker, Color Bar, UMD, Audio Alarm, Max backlight, Focus Assist, Aspect Ratio, Scan Mode, Zoom Mode, Mute, Freeze Frame, Flip Mode, Waveform, Color Temp, Timecode, Zebra, Vector. 5. GPI User can set GPI pins to relevant functions to turn on or off this function.
6. UMD ⑴ Select “Source ID” ⑵ The underline flashes as a reminder on the bottom of the first letter. Revolve "MENU" to select the letters; the letter will follow the sequence of the down below if clockwise revolved: ⑶ Press “MENU” to save the current settings letter and then start to set the next letter. ⑷ Repeat step (2) and step (3), max 8 letters are supported. ⑸ Press “Exit” to quit and save the settings. 7.
8. Audio *1 When “Bar Frame” is set to “Off”, only the audio meter will be displayed. When “Bar Frame” is set to “On”, frame and real-time audio value will be displayed. *2 Select Channel Under HDMI signal, channel1-2 can be selected. Under SDI signal, channel 1-2, 1-8 and 1-16 can be selected. *3 When “Audio Alarm” is set to “On”, if no embedded audio is detected, the audio bar will display “UNLOCKED”.
9. Vector 10. Waveform *1: Only the “WFM Single Line” is set to “ON”, the “WFM Line Count” can be adjusted. “WFM Single Line” is to display the selected line waveform of “WFM Line Count” WFM Single Line: Off WFM Single Line: On 11.
12. System *1 Source Scan When set to “Yes”, after turn on the monitor, the signal will be inspected and follow the sequence of “SDI1→SDI2→HDMI→CVBS→SDI1” *2 Logo: Refer to the startup displayed ProHD logo. *3 *4 Update Driver/ Kernel Download latest firmware files in USB disk - root directory. Switch on the monitor, and insert USB disk into the USB socket on rear panel. Enter Menu – System – Update Kernel, select YES and the monitor will upgrade automatically, and will restart when upgrade finished.
Specification LCD Performance Size Display area Resolution Color Aspect ratio Brightness Contrast Viewing angle 7 inch 151.2×94.5 mm 1920×1200 8 bit 16:9∕4:3 400 cd/m2 1000:1 Horizontal∕Vertical: 160°∕160° Input∕Output Input Output HDMI×1 BNC×2 BNC×1 3.5mm×1 USB×1 BNC×1 3.
Trouble-shooting symptom No display Image or color abnormal No audio output Possible causes Solution The power is not turned on Please check if the power is connected, and then press ”POWER” button to turn on the monitor Unstable power voltage Reconnect to power supply BNC or HDMI cable loose contact or not correctly connected Check and correctly connect the BNC or HDMI cable The attached battery is no power Change battery Using DIY power supply but the polarity is reversed Refer to the provi
This model is manufactured by SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC , and distributed in North America by JVCKENWOOD USA Corporation To obtain service or for further information, please contact: SWIT Electronics USA, LLC Address: 3350 Scott Blvd. 61-02, Santa Clara, CA 95054 Toll free: 1 866 986-SWIT (7948) • Tel: 408 260-8258·Fax: 408 228-8438 Email: info@swit.us • Website: www.swit.