MULTI FORMAT LCD MONITOR DT-V24G2 DT-V21G2 DT-V17G2 DT-V17G25 INSTRUCTIONS The illustration of the monitor is of DT-V21G2. This is the English instruction manual. Instruction manuals in other languages (German, French, Italian, Spanish, Russian) are included on the supplied CD-ROM as PDF files (for Europe only). For Customer Use: Enter below the Model No. and Serial No. which is located on the body. Retain this information for future reference. Model No. : Serial No.
Safety Precautions (English) Before use, read “Safety Precautions” carefully, and then operate the product correctly. FCC NOTICE CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Operating Precautions The LCD panel and backlight have life expectancy. Due to the basic characteristics of the LCD panel, an afterimage or uneven display may occur. It is recommended that you change images occasionally, activate the power saving function, or often turn off the power to reduce the load on the LCD panel. Continuous operations of the LCD panel may accelerate the deterioration.
Installation l Do not rest your arm on the monitor or lean against the monitor. l Do not touch the LCD panel when installing the monitor. l Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury. l How to set up 1 l To detach the stand You can tilt the monitor as follows. When the monitor is not tilted (0°), the guidelines align as illustrated below.
Index of Parts and Functions Rear panel Carry handle (DT-V21G2/DT-V17G2/ DT-V17G25 only) Use this handle when carrying the monitor. DT-V21G2/ DT-V17G2 only The illustration of the monitor is of DT-V21G2. Security slot Attach a security wire to this slot. Note for connections • Before making any connections, turn off all the equipment. • Use a cord whose plugs correctly match the terminals on this monitor and the equipment. • Plugs should be firmly inserted; poor connections could cause noise.
Index of Parts and Functions (cont.) Front panel Tally lamp This lamp is controlled by the tally function of the MAKE/TRIGGER terminal. • You can select the color of the tally lamp from “Green” or “Red.” You can also select whether the whole lamp is turned on at once, or whether it is turned on one half at a time. (+ “Tally Setting” in “Function Setting” on page 15 and “External Control” on page 20) The illustration of the monitor is of DT-V21G2.
/ 7 / / u INPUT SELECT buttons/lamps buttons Selects an input. When a menu screen is displayed selects or adjusts menu items. (+ “The operation procedure” on page 9) l Pressing button while holding button displays the Set-Up Menu (+ “Menu Configuration” on page 9). SDI 1: SDI 2: 8 MENU button Activates/deactivates the display of the Main Menu (+ “Menu Configuration” on page 9). DUAL LINK: 9 COLOR OFF button/lamp HDMI: COMPO.: VIDEO: Displays only the luminance signal.
Showing Input Signals Audio Channel Selection Select the audio channel output from the Speaker and AUDIO ASSIGN (MONITOR OUT) (OUT1(L)/OUT2(R)) terminals when an EMBEDDED AUDIO signal is input during SDI input. l Store the setting for each input of SDI 1 and SDI 2. 1 When the menu is not displayed, use the button The “Embedded Audio” screen appears. l The “Embedded Audio” screen disappears automatically is no operations are made for about 30 seconds.
Menu Configuration First Time Installation When you turn on the power and the monitor, “First Time Installation” appears. Start setting referring to the menu configuration. < First Time Installation > For the setting items, see the pages below.
Menu Configuration (cont.
Main Menu Picture Function Setting for the picture quality. Item Backlight Aperture*1 Aperture Level*1 CTI LTI Gamma To do Setting value Adjusts the brightness of the display. –20 to +20 Activates/deactivates the function at the level set in “Aperture Level”. Off, On Compensate the frequency response of the luminance signal of the video signal. 01 to 10 Adjust the clearness of the outlines of the chrominance signal. Off, Normal, Hard Adjust the clearness of the outlines of the luminance signal.
Menu Configuration (cont.) 1:1*3 Displays the picture in the original resolution of the input signal. • The aspect ratio of the picture may change depending on the input signal. 16:9 Size*1,*2,*4 Selects the picture size when the input signal format is 16:9. Normal : Matches the vertical picture size to the number of pixels. V Full : Enlarges the picture vertically. At this time, the right and left of the picture are overscanned and markers are displayed.
Audio Setting Settings for AUDIO signals, EMBEDDED AUDIO signals and audio level meter signal. Item Balance To do Adjust the balance between the right and left speakers. Setting value L5 to L1, 0, R1 to R5 SDI-1 Select*1 SDI-2 Select*1 Select the input through which audio is output. Off, Auto, Digital, Analog1, Analog2 Off : Does not output audio. Auto : Output digital audio prior to analog audio. Digital : Output audio from the SDI terminal.
Menu Configuration (cont.) Transparent Peak Hold Lissajous Setting Adjust the transparency of the level meter display against the image. Activates/deactivates the peak hold function of the level meter. Lissajous setting Y X H Axis Channel(X) Select an EMBEDDED AUDIO CH to display on the horizontal axis of the Lissajous screen. V Axis Channel(Y) Select the EMBEDDED AUDIO CH to display on the vertical axis of the Lissajous screen.
Sync Function Settings for the synchronization with signals. Item No Sync Action Delay Time Low Latency To do Select the screen status when no signal is coming in. Setting value Off, Standby, Power Save (power save mode), Gray Back (gray screen) Select the period until the screen status changes as selected in “No Sync Action” after signals 30s, 5min, 15min stop coming in. Activates/deactivates the function to shorten the time taken to display the picture (low Off, On latency function).
Menu Configuration (cont.) Standby Mode LCD Saver Setting 1st Start Work Time Contrast Backlight OSD Contrast Side Mask reset Execute Cancel Status Start After Function Key Setting Function1 Function2 Function Display Select the operation status when the monitor is powered OFF (standby). Normal, Serial, SDI Out Normal : Changes to Low Power Mode 30 seconds after powered OFF to reduce power consumption. In this case, it cannot power on by external control.
White Balance Setting Display the color temperature, and adjusts the drive level and cutoff point of each color (R/G/B). Item Color Temperature R Drive *1 G Drive B Drive R Cut Off *1 G Cut Off B Cut Off sub menu reset *1 To do Setting value Select the color temperature. (Cannot be set/changed) 9300K, 6500K, 5600K, User Adjust the drive level of each color (red, green, and blue).
Menu Configuration (cont.) SDI Format Setting value: Auto, MS1YCbCr, MS2YCbCr, MS3YCbCr, MS4YCbCr, MS2 RGB, MS3 RGB, 3G-B-DS When “Auto” is selected, 3G SDI/HD-SDI DUAL LINK signals are automatically recognized. (Normally select “Auto.”) l If the picture is unstable with “Auto”, select the setting value according to the input signal format. l “M” (meaning “Manual”) is displayed on the status display when a setting other than “Auto” is selected. IMD Settings for IMD (In-monitor Display).
l Setting of “Character Setting” 1 2 3 Change the input to one that you want to assign a video source name for. Select “Character Setting”. Press buttons to select the first character. l Each time you press button, the character changes as follows. Press button to reverse the order. Space 4 Press button to move the arrow to the next space. l The characters entered before moving the arrow are memorized. Repeat steps 3 and 4 (10 characters at maximum). Press MENU button to store the name.
External Control About the external control Using the MAKE/TRIGGER system This monitor has two external control terminals. l MAKE/TRIGGER terminal (RJ-45): The following external control systems are available. (1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it. (2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the corresponding pin terminal.
Display ––– Tally Color Tally Type Tally-L(R) Tally-R(G) SDI-1 SDI-2 HDMI Compo.
External Control (cont.) Pin No. IN terminal signal 1 2 3 4 5 6 7 8 This is a female terminal. TXD + TXD – RXD + NC NC RXD – NC GND OUT terminal signal TXD + TXD – RXD + NC NC RXD – NC GND Pin No. 1 2 3 4 5 6 7 8 9 This is a female terminal. Signal NC RXD TXD NC GND NC RTS CTS NC l The 7th terminal and the 8th terminal are connected. All commands consist of the following segments.
Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult an authorized dealer or service center. Symptom No power supply. No picture with the power on. No sound. Probable cause and corrective action button. l Press the l (DT-V17G2/DT-V21G2 only) Firmly insert the AC power plug or DC power plug. l (DT-V17G2/DT-V21G2 only) Turn on the POWER switch or DC switch on the rear panel.
Troubleshooting (cont.) Self-check program This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes troubleshooting easier. Whenever a problem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the problem. The illustration of the monitor is of DT-V21G2. When the screen goes blank, and one or some of the INPUT SELECT lamps (COMPO.
Specifications General Model name Type Screen size Aspect ratio Horizontal/vertical frequency (computer signal) Compliant video signal format Format Audio output Operating conditions Power requirements Rated current North America Europe External dimensions (excluding protruding parts) with the stand without the stand Weight Accessories North America Europe DT-V24G2 DT-V21G2 DT-V17G2 DT-V17G25 Multi format LCD monitor Type 24 wide format Type 21.5 wide format Type 16.5 wide format 16:10 16:9 H: 31.
Specifications (cont.) Dimensions Unit: mm DT-V24G2 98.7 51.9 1.3 100 VESA mounting holes (4-M4, depth:10mm) 115 100 448.6 408 564 51.3 300 DT-V21G2 243 99.8 53 1.3 100 100 VESA mounting holes (4-M4, depth:10mm) 115 347 387.6 515 20.2 240 212.9 DT-V17G2, DT-V17G25 (The illustration of the monitor is of DT-V17G2) 102 56 100 100 1.
Available signals The following signals are available for this monitor. Video signals No. Signal name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 l *1 *2 *3 *4 *5 *6 *7 *8 NTSC NTSC 4.43 PAL-M PAL60 PAL PAL-N SECAM B/W50 B/W60 480/60i 480/59.94i 576/50i 480/60p 480/59.94p 576/50p 640*480/60p 640*480/59.94p 720/60p 720/59.94p 720/50p 720/30p 720/29.97p 720/25p 720/24p 720/23.98p 1080/60i 1080/59.94i 1035/60i 1035/59.
Sicherheitsmaßregeln (Deutsch) Vor der Verwendung lesen Sie die „Sicherheitsmaßregeln“ sorgfältig durch, und bedienen Sie das Produkt richtig. Achtung: Dies ist ein Klasse-A-Produkt. In nichtgewerblichen Umgebungen können von dem Gerät Funkstörungen ausgehen, zu deren Beseitigung vom Benutzer geeignete Maßnahmen zu ergreifen sind. Ausschließlich mit der zulässigen Netzspannung.
Précautions de sécurité (Français) Assurez-vous de lire attentivement les “Précautions de sécurité”, puis d’utiliser l’appareil correctement. Avertissement: C’est un produit de classe A. Dans un environnement domestique, cet appareil peut causer des interférences radio et dans ce cas l’utilisateur peut être requis de prendre les mesures correctives nécessaires. N’utiliser que la source d’alimentation spécifiée sur l’appareil.
Precauzioni di sicurezza (Italiano) Prima dell’uso si raccomanda di leggere con attenzione le “Precauzioni di sicurezza”. Avvertenza: Prodotto di classe A. In ambiente domestico il prodotto può provocare radiodisturbi che l’utente è tenuto ad eliminare adottando idonee misure. Usare solamente le sorgenti di alimentazione specificate sull’apparecchio.
Precauciones de seguridad (Español) Para un uso seguro, asegúrese de leer detenidamente las “Precauciones de seguridad” antes de utilizar el producto. Advertencia: Este es un producto de Clase A. En un entorno residencial, este producto puede causar interferencias, en cuyo caso el usuario debe tomar las medidas adecuadas. Utilice sólo la fuente de alimentación especificada en la unidad.
Меры предосторожности (Русский) Перед эксплуатацией внимательно прочтите “Меры предосторожности”, а затем правильно управляйте изделием. Предупреждение: Данное изделие относится к устройствам класса А. В этом случае пользователю изделия, возможно, потребуется принять соответствующие меры. Используйте только источник питания, указанный на устройстве.
Указатель компонентов и функций Задняя панель Ручка для переноски (только DTV21G2/DT-V17G2/DT-V17G25) Пользуйтесь этой ручкой при переноске монитора. Только DT-V21G2/ DT-V17G2 На рисунке изображен монитор DT-V21G2. Гнездо безопасности Прикрепите шнур безопасности к этому гнезду. Примечание по подключениям • Прежде чем приступить к подключению, выключите все устройства. • Используйте шнур, штепсельные разъемы которого в точности совпадают с разъемами на мониторе и устройствах.
Указатель компонентов и функций (продолжение) Передняя панель Сигнальный индикатор Данным индикатором управляет функция сигнальной индикации разъема MAKE/TRIGGER. • Можно выбрать цвет сигнального индикатора из вариантов “Зеленый” или “Красный”. Также можно выбрать режим работы индикатора: он может включаться сразу полностью либо наполовину за раз. На рисунке изображен монитор DT-V21G2. 1 - e, i и ; являются общими для DT-V24G2, DT-V21G2, DT-V17G2 и DT-V17G25. На рисунке изображен монитор DT-V21G2.
7 Кнопки / / u Кнопки/индикаторы INPUT SELECT / Когда отображается экран меню, позволяют выбрать или настроить элементы меню. l Нажатие кнопки при нажатой кнопке выводит на экран Меню настроек. 8 Кнопка MENU Включает/выключает отображение Главное меню. 9 Кнопка/индикатор COLOR OFF Отображает только сигнал яркости. l Эта функция не работает для входных сигналов RGB. p Кнопка/индикатор SCOPE Отображает/скрывает индикацию формы сигнала и вектроскопа.
MULTI FORMAT LCD MONITOR DT-V24G2 / DT-V21G2 / DT-V17G2 / DT-V17G25 © 2016 JVC KENWOOD Corporation DT-V24G2_EN.
