INSTRUCTIONS DT-V17L2D BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS ISTRUZIONI MANUAL DE INSTRUCCIONES ИHCТРУKЦИЯ ПО ЭКСПЛУАТАЦИИ MULTI FORMAT LCD MONITOR MULTI FORMAT LCD MONITOR MONITEUR LCD MULTI-FORMAT MONITOR LCD MULTIFORMATO MONITOR LCD MULTIFORMATO МУЛЬТИФОРМАТНЫЙ ЖК МОНИТОР LCT2346-001A ITALIANO FRANÇAIS DEUTSCH ENGLISH ESPAÑOL РУССКИЙ
CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock. Do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.
2 Safety Precautions WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS. IMPORTANT SAFEGUARDS Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRIC SHOCK OR FIRE.
U.S.A. only European Union only FCC NOTICE CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
4 Installation CAUTION • Do not rest your arm on the monitor or lean against the monitor. • Do not touch the LCD panel when installing the monitor. • Make sure to install the monitor securely to prevent the monitor from falling over, which causes damage to the monitor or injury. To detach the stand CAUTION Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged. You can place the monitor in the following two ways when using the monitor on the supplied stand.
To adjust the stand height To prevent an accidental fall You can select the stand height—higher position or lower position. To change the stand height, change the position of the stand plate as illustrated below after detaching the stand from the monitor. • For detaching the stand, see “To detach the stand” on page 4. Fix the monitor to a wall by using strings.
6 Daily Operations / Connections 7 Front panel • “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not actually work). • The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed and the lamps do not light).
Menu Operations Audio Channel Selection About the Information Display About the Status Display 1 Display the menu. Select audio channels emitted from the speakers (L/R) and the MONITOR OUT (L/R) terminals, when EMBEDDED AUDIO signals come in to the E. AUDIO HD/SD SDI terminal (IN1 or IN2) and SDI input (1 or 2) is selected. • You have to choose a group of selectable audio channels before the channel selection (☞ “E.AUDIO GROUP” in “AUDIO SETTING” on page 11).
8 Daily Operations / Connections (cont.) 7 Rear panel Carry handle Use this handle when carrying the monitor. CAUTION Do not connect the power cord until all other connections are completed. Security slot Install a security wire to this slot. 1 REMOTE terminal Terminal for controlling the monitor by an external control. ☞ “External Control” on page 14 2 VIDEO terminals (BNC) Input (IN) and output (OUT) terminals for the composite signals. 3 COMPO.
7 Available signals Computer signals (preset) DVI-D (HDCP) terminals The following signals are available for this monitor. Video signals No. Signal name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 NTSC PAL B/W50 B/W60 480/59.94i 576/50i 480/59.94p 576/50p 640∗480/59.94p 720/60p 720/59.94p 720/50p 720/30p 720/29.97p 720/25p 720/24p 720/23.98p 1080/60i 1080/59.94i 1035/60i 1035/59.94i 1080/50i 1080/60p 1080/59.94p 1080/50p 1080/30p 1080/29.
10 Menu Configuration—MAIN MENU For the operation procedure, see page 7. PICTURE IMPROVEMENT Setting for the picture quality Item APERTURE FREQ.*1 APERTURE LEVEL*1 CTI LTI sub menu reset To do Setting value Select the frequency of the luminance signal compensated in OFF, LOW, HIGH “APERTURE LEVEL.” Compensate the frequency response of the luminance signal of the 01 – 10 video signal. Adjust the clearness of the outlines of the chrominance signal.
AUDIO SETTING Setting for the audio output balance, EMBEDDED AUDIO signals and level meter Item BALANCE Adjustment bar Displayed when selecting “BALANCE.” Operation guide Shows the buttons for each operation. E.AUDIO GROUP*1 LEVEL METER SETTING*1 LEVEL METER ch BAR TYPE Select the color of the level meter display. REFERENCE LEVEL OVER LEVEL Select the standard input level indicated on the level meter. Select the input level’s lower limit indicated in red for the “3COLORS” display.
12 Menu Configuration—SET-UP MENU FUNCTION SETTING For the operation procedure, see page 7. Setting for the sub menu display, color system, and color of the tally lamp Item sub menu POSI. COLOR SYSTEM TALLY SELECT To do Select the contents and displaying position of “sub menu.” Select the color system. • If the picture is unstable with “AUTO,” select “PAL” or “NTSC.” Select the color of the tally lamp. Setting value ☞ “NOTE” AUTO, NTSC, PAL GREEN, RED PICTURE SUB ADJ.
REMOTE SETTING (☞ “External Control” on pages 14 and 15) Setting for the external control Item SERIAL TYPE PARALLEL TYPE PIN1, PIN2, PIN3, PIN4, PIN5 Operation guide Shows the buttons for each operation. To do Select the input terminal used for external control by serial communication. Select the external control method for the MAKE/ TRIGGER terminal. Assign the control functions to the pins of the MAKE/ TRIGGER terminal. • Assign a function to each pin terminal by selecting “SET” in “PARALLEL TYPE.
14 External Control 7 About the external control This monitor has three external control terminals. • MAKE/TRIGGER terminal (RJ-45): The following external control systems are available. (1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it (☞ below). (2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the corresponding pin terminal (☞ below).
Operation 1 Set “PARALLEL TYPE” of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the SET-UP MENU. 2 Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled by the external control. 3 When selecting “MAKE” system: Operate each function by short-circuiting the corresponding pin terminal to the 8th pin terminal (GND) or opening it.
16 Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solves the problem, unplug the monitor and consult an authorized dealer or service center. Symptom No power supply No picture with the power on No sound “OTHERS” or “Out of range” appears. “NO SYNC” appears. Wrong color, no color The picture becomes blurred. Wrong picture position, wrong picture size. Some items do not appear on the menu.
Specifications Compliant video signal format Format Audio output Operating conditions Power requirements Rated current External dimensions (excluding protruding parts) Weight Accessories 600:1 H: 31.469 kHz – 75.000 kHz V: 60 Hz ± 5 Hz * Some signals within this frequency range may not be displayed (“Out of range” is displayed). ☞ “Available signals” on page 9 HD SDI: BTA S-004B, SMPTE292M SD SDI: ITU-R BT.656: 525/625 SMPTE259M: 525 EMBEDDED AUDIO: SMPTE299M, SMPTE272M Internal speaker: 1.0 W + 1.
18 Specifications (cont.) 7 Dimensions Unit: mm 86 VESA mounting holes (4-M4, depth: 10 mm) 1.5 300 64 100 100 395 115 304 344.6*/309.6** 40 243 * at the higher position ** at the lower position DT-V17L2D_EA_EN_R.indd 18 07.9.
© 2007 Victor Company of Japan, Limited 0907MKH-MW-VP