. D-ILA Projector Set up DLA-VS4550 DLA-VS4600 DLA-VS4700 Getting Started INSTRUCTIONS Operate DISPLAYPORT INPUT 2 INPUT 3 INPUT 4 QUAD LENS CONTROL C.M.D. MOTION ENHANCE NATURAL DYNAMIC NAME EDIT USER1 USER2 USER3 USER4 USER5 USER6 GAMMA COLOR TEMP. LENS AP. DUAL Adjust/Set INPUT 1 PIC. ADJ. . Maintenance Troubleshooting Others For Customer use : Enter below the serial No. which is located on the side of the cabinet. Retain this information for future reference.
Safety Precautions Getting Started IMPORTANT INFORMATION WARNING: WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This equipment is compliant with Class A of CISPR 32. In residential environment this equipment may cause radio interference. WARNING: THIS APPARATUS MUST BE EARTHED. CAUTION: To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel.
IMPORTANT SAFEGUARDS 300 mm and above 150 mm and above Front Getting Started Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, use and service. Please read these Important Safeguards carefully before use.
Getting Started - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
POWER CONNECTION Power cord The power supply voltage rating of this product is AC100V – AC240V. Use only the power cord designated by our dealer to ensure Safety and EMC. Ensure that the power cable used for the projector is the correct type for the AC outlet in your country. Consult your product dealer. Power cord Getting Started For USA and Canada only Use only the following power cord.
ENGLISH Getting Started Information for Users on Disposal of Old Equipment and Batteries [European Union only] These symbols indicate that equipment with these symbols should not be disposed of as general household waste. If you want to dispose of the product or battery, please consider the collection systems or facilities for appropriate recycling. Battery Products Notice: The sign Pb below the symbol for batteries indicates that this battery contains lead.
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This Projector is classified as a CLASS 3R LASER PRODUCT. This CLASS 3R LASER PRODUCT label and Caution label is located on the Rear Side surface of the projector. LASER RADIATION AVOID DIRECT EYE EXPOSURE CLASS 3R LASER PRODUCT WAVE LENGTH : 453nm MAX OUTPUT : 83.
For the customers In other countries Getting Started CLASS 1 LASER PRODUCT LASER CAUTION LABEL WARNING Do not look into the lens while in use. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
For the customers In China Getting Started 9
Contents Getting Started Getting Started Safety Precautions .................................................. 2 Accessories/Optional Accessories ........................ 11 Check the Accessories ...................................... 11 Controls and Features ........................................... 12 Main Unit - Front ................................................ 12 Main Unit - Bottom ............................................. 12 Main Unit - Rear ................................................
Accessories/Optional Accessories Getting Started Check the Accessories Remote control ....................................................................... 1 piece AAA-size batteries (for operational check) ............................ 2 pieces Power cord (for USA) (about. 2 m) ......................................... 1 piece Power cord (for EU) (about 2 m) ............................................. 1 piece Lens spacer ............................................................................
Controls and Features Getting Started Main Unit - Front B C D D A C Indicator A Lens (sold separately) Zoom lens or short focal length lens is optional. Refer to “Indicator Display on the Main Unit”P. 70. D Exhaust vent B Remote Sensor (front) Please aim the remote control at this area when using it. * There is also a remote sensor at the rear. Warm air is discharged to cool down the internal temperature. Do not block the vents.
F Getting Started Main Unit - Rear G H I J F Input terminals For details on the terminals, refer to “Main Unit - Input Terminals”P. 14. “Operation panel” in the diagram below. H Remote Sensor (rear) G Operation panel Please aim the remote control at this area when using it. For more details, please refer to the I Power input terminal Connect the supplied power cord to this terminal. Do not block the inlet. Do not blow hot air on the inlet. Doing so may cause the unit to malfunction.
Getting Started Main Unit - Input Terminals Enlarged View of Rear Face A B C A [SYNC OUT] terminal For synchronizing with other equipment. Outputs L and R sync signals during 3D signal input. (P. 34) B [SERVICE] terminal For updating the software using a commercially available USB flash drive. C [RS-232C] terminal (D-sub 9-pin male) The projector can be controlled by connecting a PC to this terminal.
A B [STANDBY] M [PICTURE MODE] A B C [ON] 0 B C [DISPLAYPORT] 0 Turns off the power. (P. 25) Turns on the power. (P. 24) Switches the input to [DisplayPort 1] to [DisplayPort 4], [Dual] or [Quad]. (P. 24) DISPLAYPORT C INPUT 1 INPUT 2 DUAL INPUT 3 INPUT 4 QUAD C.M.D. MOTION ENHANCE D [LENS CONTROL] For adjusting focus, zoom, and shift. (P. 35) E [C.M.D.] D E F LENS CONTROL 0 For setting frame processing. (P.
Getting Started Loading Batteries into the Remote Control Loading the batteries 0 0 0 If the remote control has to be brought closer to the unit to operate, it means that the batteries are wearing out. Replace the batteries with new ones (AAA). Insert the batteries according to the t s marks. Be sure to insert the s end first. When removing the battery, do so from the t end. If an error occurs while using the remote control, remove the batteries and wait for five minutes.
A B C D E F Select the icon at the top of the menu to display its corresponding setting item as shown below.
Installing the Projector Precautions during Installation Please read the following carefully before installing this unit. When carrying this unit Maintain clearance from the wall, etc. As the unit discharges a large amount of heat, install it with adequate clearance from the surroundings as shown below. Set up This unit is heavy in weight. Please ensure that there are at least two persons carrying it. Do not install at the following This unit is a precision device.
Precautions during Mounting Securing (mounting) the projector 0 When this unit is to be mounted to a fixed position for use, install it horizontally. 0 Make sure to secure the main unit to prevent accidents such as during an earthquake. Set up Securing the projector (directly mount) For directly mounting projectors to a stand for motion or non-motion systems, remove the four feet from the base of the projector and use the inner six mounting screw holes (see pictures below).
Securing the projector (ceiling mount) Installing the ceiling mounting bracket A Remove the rear foot (x2). 0 The removed feet can be installed to the rear holes. (*1) 0 It is not necessary to remove the front feet. However, it will not pose any usage problems even when they are removed. Front Set up 0 Be sure to ask your dealer to install the unit for you. Installing the unit on your own may cause the unit to fall resulting in injury.
Adjusting the Position Adjusting the elevation angle of the projector The height and inclination of the unit (0 to 5 mm) can be adjusted by turning the feet. Lift the unit and adjust the four feet.
Connecting the Projector 0 Do not turn on the power until connection is complete. 0 The connection procedures differ according to the device used. For details, please refer to the instruction manual of the device to be connected. 0 This projector is used for projecting images. To output the audio of connected devices, please connect a separate audio output device, such as an amplifier or speaker. 0 Some cables cannot be connected to this unit due to the size of their connector cover.
Connecting to the RS-232C Terminal This Unit Laptop, etc. To [RS-232C] Terminal RS-232C Terminal RS-232C Connection Cable (Sold Separately) Set up For more information on control, please refer to “External Control”P. 58. 0 Connecting to the REMOTE Terminal This Unit To [REMOTE] Terminal Connection Cable (Sold Separately) Wired Remote Controller (Sold Separately) For more details on the wired remote controller and connection cable, please consult your dealer.
Viewing Videos MEMO 0 WARNING LIGHT Connect the power cord, and ensure that the “STANDBY/ON” indicator lights up in red.
3 Turn off the power Remote control: press the B [STANDBY] button Projector unit: press the A button 0 While the “Are you sure you want to turn off?” message is displayed, press the button again. 0 The light of the LD block goes off, and the “STANDBY/ON” indicator switches from a green light to a red blinking light. 0 After the light goes off, the fan will run for about 10 seconds to cool down the LD block (Cool-down mode). Do not disconnect the power cable while cooling is in progress.
Adjustments and Settings in the Menu Pressing the [MENU] button displays the menu. Press the [JKH I] keys to select an item, followed by pressing the [OK] button to confirm the selection. List of Menu Items Picture Adjust Picture Mode ................................................................................................................................................... P. 28 9 Sharpness ..............................................................................................................
Installation Lens Control .................................................................................................................................................... P. 35 9 Focus ......................................................................................................................................................... P. 35 9 Zoom ..........................................................................................................................................................
Picture Adjust Picture Mode You can adjust the image quality according to the type of video image you are viewing. Setting Description Natural Image quality that focuses on natural color and gradation reproduction. Suitable for displaying video images in general. Dynamic This is the picture setting best suited for viewing the picture in a room that cannot be made completely dark. User 1 to User 6 Enables user-defined image quality data to be saved and retrieved.
User Name Edit You can edit the “User 1” to “User 6” names in the Picture mode. 0 Characters that are usable include alphabets (upper or lower case), numeric characters, and symbols. 0 Enter not more than 10 characters. User Name Edit Selection Cursor Input Cursor Name User 1 A B C D E F G H I J K L N O P Q R S T U V W X Y Z a b c d e f g h i j k l m z M n o p q r s t y v w x y 1 2 3 4 5 6 7 8 9 0 , .
Color Temp. For setting the color temperature of the video image. 0 The selectable “Color Temp.” settings vary according to “Picture Mode”. “Color Temp.” Color Temp. 5500K Description Increasing the value enhances the blue tone of the video image, while decreasing the value enhances the red tone. 6500K 9500K High Bright Color temperature that gives priority to brightness.
Gamma You can adjust the output value of the projected image with respect to the video signal input. “Gamma” Gamma Description 2.2 The gamma is set to “2.2”. Custom 1 to Custom 3 Enables fine adjustment of gamma according to preference. You can perform fine adjustments based on the selected gamma adjustment setting.
Blur Reduction For reducing the after-image, which occurs in a fast-moving scene. 0 Blur Reduction is grayed out and cannot be adjusted when signal is out of range or during 3D input detection. Clear Motion Drive For reducing the after-image, which occurs in a fast-moving scene. 0 Pressing the [C.M.D.] button each time switches the mode in the following sequence: “Off” " “Mode 1” " “Mode 2” " “Mode 3”"“Off”... * C.M.D. is the abbreviation for Clear Motion Drive.
Input Signal Input Level For setting the dynamic range (gradation) of the video input. 0 If the dynamic range is not appropriate, the bright areas become overexposed, and the dark areas become underexposed. Setting Description 16-235 (Video) Select this setting if you are inputting video signals (dynamic range: 16 - 235). 0-255 (PC) Select this setting if you are inputting PC signals (dynamic range: 0 - 255). Color Space For setting the color space of the input signal.
3D Setting For performing 3D settings. 3D Format For selecting the method to detect 3D signal. When “3D” is selected, the L and R sync signals are output from the Sync Out terminal. (P. 14) Setting Description 2D Detects the input signal as 2D signal. 3D Detects the input signal as 3D signal. Crosstalk Cancel This is the function to correct the crosstalk between the left and right images.
Installation Lens Control Focus / Zoom / Shift For adjusting the lens according to the projection position MEMO To use the Shift function, a motorized lens shift unit is required. For details on installing the motorized lens shift unit (sold separately), refer to the instruction manual of the motorized lens shift unit. Motorized lens shift unit (product no.
Pixel Adjust For correcting the phase shifting between each RGB color by adjusting the pixel. Adjust For setting the adjustment feature to On or Off. Adjust Area Setting Description Whole Adjusts the entire image. Zone Enables fine adjustment of each area by dividing the screen evenly into 10 vertical and horizontal zones. Adjust Color For selecting the color to adjust (“Red” or “Blue”).
Whole Adjust (Pixel) Operation Procedure For making general adjustments to slight color fringing in the horizontal/vertical directions of the video image. A Set “Adjust Area” to “Whole” B Select “Adjust Color” and “Adjust Pattern Color” C Select “Adjust (Pixel)”, and press the [OK] button 0 The Adjustment mode is activated, and the selected adjustment pattern and Adjustment (Pixel) window are displayed.
Whole Adjust (Fine) Operation Procedure For making general adjustments on the misalignment of the entire screen using “Adjust (Pixel)”, followed by making fine adjustments. A Set “Adjust Area” to “Whole” B Select “Adjust Color” and “Adjust Pattern Color” C Select Adjust (Fine), and press the [OK] button 0 The Adjustment mode is activated, and the selected adjustment pattern and Fine window are displayed. 0 The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.
Zone Adjust Operation Procedure For fine-tuning misalignments on a part of the screen after adjusting the overall screen misalignment using “Adjust (Pixel)” and “Adjust (Fine)”. 0 The screen can be divided vertically and horizontally into 10 sections for partial adjustments to be made.
Mask For hiding the peripheral area of the image with a mask (black strip). Setting Description Off Not masked. On Hides the ranges specified in “Top”, “Bottom”, “Left” and “Right” by masking (with black strips). Off On Mask: black strip around the periphery “Top” / “Bottom” / “Left” / “Right” For specifying the ranges to hide by masking (with black strips). 0 Setting range: 0 to 220 Distortion Correction Corrects distortion of the screen.
Operation procedure for Adjust A Select “Adjust Pattern Color” B Select “Adjust”, and press the [OK] button 0 The Adjustment mode is activated, and the selected adjustment pattern and Adjustment window are displayed. Distortion Correction Position 0 / 0 H 0 V 0 Back BACK C Select the position to compensate by using the [JKH I] keys to move the cursor, followed by pressing the [OK] button.
Edge Blending Corrects the seam between the images during projection by multiple projectors. * This function is disabled when “Picture Mode” is set to “Dynamic”. Edge Blending For setting the function to On or Off. Setting Description Off Disables the Edge Blending function. On Enables the Edge Blending function. Guide For setting the guideline display (start point: green; end point: red). Setting Description Off Hides the guideline. On Displays the guideline.
LED Indication When “LED Indication” is set to “Off”, the LED indicator does not light up or blink under the following status. 0 When the time to replace the laser light source is near. (P. 48) 0 When HIDE is on. (P. 70) 0 When the projector receives a signal from a remote control which is set to a different code mode (A or B). (P. 47) High Altitude Mode For setting the high altitude mode to “On” or “Off”.
Operation procedure on the Adjust Screen V (Vertical) Adjustment Pattern Auto Geometry Stabilizer Red Point: 10 min. H 0 V 0 Color A. R Mute G Mute B Mute COLOR TEMP GAMMA LENS AP. PIC. ADJ. Back BACK Adjust Window H (Horizontal) Auto Geometry Stabilizer Point: 10 min. Correction Time Color for Adjustment Red Correction Value H 0 V 0 Color A. R Mute G Mute B Mute GAMMA COLOR TEMP LENS AP. PIC. ADJ.
Display Setup Back Color For setting the color of the background to “Blue” or “Black” when there is no signal input. Menu Position For setting the display position of the menu. Signal Display For setting the display of the input information to “On” or “Off”. Setting Description Off Not displayed. On Shows the input terminal for 5 seconds when input is switched. Logo For setting the display of logo during startup to “On” or “Off”. Setting Description Not displayed.
Function Sync Out For selecting the type of signal to output from Sync Out. Setting Description Input (Positive) Outputs a signal that is synchronized with the vertical sync signal of the input video signal. (*) Input (Negative) Outputs a signal with reversed polarity that is synchronized with the vertical sync signal of the input video signal. (*) Low Fixes the output at Low. High Fixes the output at High.
Remote Code For changing the remote control code. Setting Description A Change the remote control code from “B” to “A”. B Change the remote control code from “A” to “B”. 0 You need to configure the remote control according to the settings of this unit. On the remote control unit, press the [MENU] and [BACK] buttons at the same time for three seconds or longer to switch the code.
Information Page 1 Setting Description Input Displays video input terminal. Status Displays the image output status. Resolution (DP 1 / DP 2 / DP 3 / DP 4) Displays the resolution information of signal input to each of the DP 1 to DP 4 terminals. Light Source Time Displays the laser light source time. Soft Ver. Displays the firmware version. Pages 2 to 5 Setting Description Adjust/Set DP 1 to DP 4 Displays the terminal for which the corresponding information is displayed.
Maintaining the Cabinet and Remote Control 0 Gently wipe off dirt on the cabinet with a soft cloth. 0 If it is extremely dirty, wet a cloth in water, wring dry and use it to wipe off the dirt, followed by wiping again with a dry cloth. 0 Pay attention to the following as the cabinet may deteriorate in condition or the paint may come off.
CAUTION Do not wash the air filter with water. Doing so may cause the filter to deteriorate. Make sure to attach the air filter and sponge filter in the correct sequence. 0 0 MEMO If the air filter or sponge filter is damaged and requires replacement, or if dust gets into the unit, consult your authorized dealer or nearby service center. Air filter Product no.: F1K-0062-00 Sponge filter Product no.
About the Lens 0 This projector does not come with a projection lens. To use the projector, please mount a projection lens according to your requirements. 0 When using an optional standard zoom lens or short focus lens, a spacer and shift plate are required. Use the spacer that comes with this unit. The shift plate varies depending on the tilting angle of the lens so please contact our sales representative. 0 To use the Shift function, a motorized lens shift unit is required.
2 Unscrew the screw using a Phillips screwdriver to remove the front plate Front Plate 3 Secure the lens spacer to the shift plate using the supplied screws Lens Spacer (This part is bundled in the Accessory BOX) Screw×4 (Please use the screws packed with Lens Spacer) Shift Plate (optional) 4 Attach the spacer and insert lens 0 Attach the Lens Spacer and Shift Plate to the Lens Holder and fasten using the 4 screws packed with Lens Spacer using a Phillips screwdriver.
5 Connect the motor cable 0 Connect the motor cable (20pin) to lens. Motor Cable CAUTION 0 6 Keep the cable away from the motor gear when clamping the motor cable. Tighten the 4 screws using the Phillips head screwdriver to fasten the lens 0 Use the screws that comes with the lens. * The recommended tightening torque for the screws for mounting the lens is 1.47N・m (15kgf・cm).
Troubleshooting Before sending the unit to your authorized dealer for repair, please check the following points. The following symptoms are not malfunctions. You do not need to worry about the following symptoms if there is no abnormality on the screen. 0 A part of the top or front surface of the unit is hot. 0 A creaking sound is heard from the unit. 0 An operating sound is heard from the inside of the unit. 0 Color smear occurs on some screens. This unit is a digital device.
3D images do not appear Check Action Refer to Is an intermediate device (AV amplifier, Connect the source device to the projector directly, and divider, etc.) in use? check whether there is any improvement in the condition. If the condition improves, it is likely that this is not caused by malfunction of the projector. Is the power of the 3D Glasses turned on? Check the power of the 3D Glasses. — Check the instruction manual of the 3D Glasses.
Projected image is dark Check Action Refer to Is the laser light source near exhaustion? Check the laser light source time in the “Information” menu. P. 48 If 20,000 hours have elapsed, the brightness will be half the brightness at shipment. Is the aperture closed? Increase the value of the “Aperture” setting. P. 28 Is the value of the “LD Current” setting small? Increase the value of the “LD Current” setting. P.
When the Following Messages Appear... Message Description 0 No device is connected to the input terminal. 0 The input terminal is connected but there is no signal. No Input DP 1 Action Input the video signals. A video signal that cannot be used with Input video signals that can be used. this unit has been input (the names of (P. 65) input terminals such as “DP 1” will be displayed in yellow).
External Control It is possible to control this unit by connecting it to a PC using an RS-232C cross cable (D-sub 9-pin). The projector can be controlled by connecting it to a PC through the computer network with a LAN cable for control commands to be sent to the projector. Æ “ Network ” (P. 46) 0 Please use it after you have gained proper understanding from professional books or consulting the system administrator. RS-232C Specifications This Unit Pin No.
Command Format The command between this unit and the computer consists of “Header”, “Unit ID”, “Command”, “Data” and “End”. 0 Header (1 byte), Unit ID (2 bytes), Command (2 bytes), Data (n bytes), End (1 byte) Header This binary code indicates the start of communication.
Remote Control Code Binary code is sent during communication. 0 The following applies to the case when the remote control code is “A”. In the case of “B”, add “36” to the beginning of the code.
Communications Example This section shows the communication examples of RS-232C.
Specifications Product Name D-ILA Projector Model Name DLA-VS4550, DLA-VS4600, DLA-VS4700 Display Panel/Size D-ILA device *1, 2 0.69” 4K D-ILA (4096 x 2160 pixels) x 3 Light Source Blu-Escent Laser / Phosphor Screen Size Approx. 60” to 300” (Aspect ratio of 4096 x 2160) Brightness 3000 lm e g, 4000 lm f Projection Distance Refer to P. 63. Input Compatibility Signal Refer to P. 65. Display Resolution 4096 x 2160 pixels e f, 8192 x 4320 pixels g*3 Input Terminal DisplayPort 1.
Screen Size and Projection Distance GL-MZ4009Z Screen Size Diagonal (Inch) Projection Distance (m) 17:9 Screen 16:9 Screen Wide-end Tele-end Wide-end Tele-end 60 1.22 1.74 1.29 1.83 70 1.44 2.04 1.52 2.15 80 1.65 2.34 1.74 2.47 90 1.87 2.65 1.97 2.78 100 2.08 2.95 2.19 3.10 110 2.30 3.25 2.42 3.42 120 2.52 3.55 2.65 3.74 130 2.73 3.85 2.87 4.05 140 2.95 4.15 3.10 4.37 150 3.16 4.46 3.33 4.69 160 3.38 4.76 3.55 5.00 170 3.59 5.06 3.78 5.
GL-MZ4014Z Screen Size Diagonal (Inch) Projection Distance (m) 17:9 Screen 16:9 Screen Wide-end Tele-end Wide-end Tele-end 60 1.66 3.43 1.75 3.61 70 1.96 4.02 2.06 4.23 80 2.25 4.60 2.37 4.84 90 2.54 5.19 2.67 5.46 100 2.83 5.77 2.98 6.07 110 3.12 6.36 3.28 6.69 120 3.41 6.94 3.59 7.30 130 3.70 7.53 3.90 7.92 140 3.99 8.11 4.20 8.53 150 4.28 8.70 4.51 9.15 160 4.58 9.28 4.81 9.76 170 4.87 9.87 5.12 10.38 180 5.16 10.45 5.43 10.
Types of Possible Input Signals Single - DP1 - DP4 Original Input Signal Projector Designation Resolution Terminal for Resolution Connection VGA 1080p 2K [DP 1] / [DP 2] / 1920 x 1080 [DP 3] / [DP 4] 640 x 480 2048 x 1080 640 x 480 fh [kHz] fv [Hz] dot CLK [MHz] No. of Total No. Total No. No. of Effective of Dots of Lines Effective Lines [dot] [line] Dots [dot] [line] 31.469 59.940 25.18 800 525 640 480 1920 x 1080 56.250 50.000 148.50 2640 1125 1920 1080 67.433 59.940 148.
Dual - stripes Original Input Signal Projector Designation Resolution Terminal for Resolution Connection WQXGA 4K fh [kHz] 2560 x 1600 [DP 1], [DP 3] 1280 x 1600 99.458 3840 x 2160 1920 x 2160 135.000 59.987 174.25 1752 1658 1280 1600 348.50 1752 1658 1280 1600 60.000 297.00 2200 2250 1920 2160 120.000 594.00 2200 2250 1920 2160 2048 x 2160 112.500 50.000 297.00 2640 2250 2048 2160 135.000 60.000 297.00 2200 2250 2048 2160 270.000 120.000 594.
Dual - frame sequential Original Input Signal Projector Designation Resolution Terminal for Resolution Connection WQXGA 4K 2560 x 1600 [DP 1], [DP 3] 3840 x 2160 4096 x 2160 fh [kHz] No. of Total No. Total No. No. of Effective of Dots of Lines Effective Lines [dot] [line] Dots [dot] [line] dot CLK [MHz] fv [Hz] 2560 x 1600 99.46 59.99 348.5 3504 1658 2560 1600 3840 x 2160 134.87 59.94 593.4 4400 2250 3840 2160 135.00 60.00 594.0 4400 2250 3840 2160 4096 x 2160 112.50 50.
Quad - stripes Original Input Signal Projector Designation Resolution Terminal for Resolution Connection 4K 3840 x 2160 [DP 1], [DP 2], [DP 3], 4096 x 2160 [DP 4] fh [kHz] 960 x 2160 135.000 270.000 1024 x 2160 135.000 270.000 fv [Hz] dot CLK [MHz] No. of Total No. Total No. No. of Effective of Dots of Lines Effective Lines [dot] [line] Dots [dot] [line] 60.000 148.50 1100 2250 960 2160 120.000 297.00 1100 2250 960 2160 60.000 148.50 1100 2250 1024 2160 120.000 297.
Quad - frame sequential Original Input Signal Projector Designation Resolution Terminal for Resolution Connection 4K 3840 x 2160 [DP 1], [DP 2], 4096 x 2160 [DP 3], [DP 4] fh [kHz] fv [Hz] No. of Total No. Total No. No. of Effective of Dots of Lines Effective Lines [dot] [line] Dots [dot] [line] 1920 x 2160 135.000 60.000 297.00 2200 2250 1920 2160 2048 x 2160 135.000 60.000 297.
Indicator Display on the Main Unit Meaning of the front panel indicators The indicator lights up. The indicator appears blinking. WARNING LIGHT STANDBY/ON Operation mode display Displays using the different colors and solid/blinking light of the indicator on the projector unit.
Warning display You can tell the details of a warning from the (repeated) displays of the “WARNING” and “LIGHT” indicators. The “STANDBY/ON” indicator will light up or appear blinking according to the operation mode of the projector unit. (Please refer to ““Operation mode display”P. 70”.) The Warning mode is activated once the message is displayed. Projection is interrupted, and the cooling fan is turned on for about 10 seconds. The power cannot be turned on again while cooling is in progress.
Dimensions (Unit: mm) Top Surface Bottom Surface 290 560 Ø6 0 41 500 Front 133 235 130 22 205 20 66 110 127 Rear Surface 133 Others 72 208 37 108 157 175 41 74 49 154 290 308 440 703 337
Index A Accessories.......................................................... 11 Adjust (Auto Geometry Stabilizer).........................43 Adjust (Distortion Correction)................................40 Adjust (Fine)......................................................... 36 Adjust (Pixel Adjust)..............................................36 Adjust (Pixel).........................................................36 Adjust Area (Pixel Adjust).....................................
N Network................................................................ 46 O Off Timer...............................................................46 Offset Blue............................................................ 30 Offset Green......................................................... 30 Offset Red.............................................................30 P Picture Adjust........................................................28 Picture Mode.................................................
Others 75
. 0322KSH-SW-X © 2022 DLA-VS4550、DLA-VS4600、DLA-VS4700 D-ILA Projector .