Introduction Before recording Settings and adjustments for recording Digital Camera Basic operations Model KY-F70 INSTRUCTIONS Various recording methods Y-F70 RA K AME AL C DIGIT T N OU C-M Menu screen settings Connecting to a PC Illustration with optional lens attachment. Others For Customer Use: Enter below the Serial No. which is located on the unit. Retain this information for future reference. Model No. KY-F70 This instruction book is made from 100% recycled paper. Serial No.
Thank you for purchasing the JVC KY-F70 Digital Camera.
WARNING ON LITHIUM BATTERY The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat avobe 100°C or incinerate. Replace battery with Panasonic (Matsushita Electric). CR2032, use of another battery may present a risk of fire or explosion. • Dispose of used battery promptly. • Keep away from children. • Do not disassemble and do not dispose of in fire. For Sweden VARNING Explosionsfara vid felaktigt batteribyte.
Table of Contents 1. Introduction Features ........................................................................................................................... 6 Accessories and attachments .......................................................................................... 6 Cautionary notes for the correct usage of this product .................................................... 7 Part names and their functions .................................................................................
. Various recording methods Recording a PC monitor ................................................................................................. 40 Outputting negative images ........................................................................................... 41 Synchronizing flash and FREEZE .................................................................................. 42 About ALC and EEI operations ......................................................................................
1. Introduction Features ● This digital camera uses three 1.45 million pixel 1/2 inch IT CDD. ● Newly developed 1/2 inch C mount Dichroic prism for the color separation prism. ● Capable of recording semi-animation (7.5 frames per second) and still images at resolution of 1360 × 1024 pixels. ● Image capturing capability using a capture board since video signals are processed in realtime by the built-in DSP and outputted as RGN analog signals of 7.5 frames/sec.
Cautionary notes for the correct usage of this product • Before recording an important event, etc., always check to make sure that this product is working properly. • We are not liable for any missed recordings caused by malfunction of this unit, etc. m Phenomena unique to CCD • Smearing and blooming When using CCD to record a bright light source, a smearing effect may occur running a white line parallel to the light source.
1. Introduction (continued) Part names and their functions [Front and bottom] C-M OU @ @ @ @ @ @ ^ Lens mount Although the lens mount conforms to the type C mount lens, there are restrictions on the lenses that can be used. Mounting the lens ( Z page 17) _ Camera mounting bracket Although the mounting bracket is mounted on the bottom of the camera when shipped, the bracket can also be mounted on the top of the camera.
[Rear] SCSI SEND AW/SEL MODE MENU UP DOWN REC SET PLAY FREEZE LENS MONITOR REMOTE DC IN ON 1 2 3 4 POWER SEE INSTRUCTION MANUAL c MENU button Press this button to output the menu screen from the MONITOR terminal. Press the button once more to clear the menu screen. Setting in the menu screen ( Z page 44) d SEND/UP button ● Press this button to output the same still image* that is being outputted to the MONITOR terminal to an MO drive or printer.
1. Introduction (continued) Part names and their functions (continued) [Rear (continued)] Ventilation hole SCSI SEND AW/SEL MODE MENU UP DOWN REC SET PLAY FREEZE @ @ @ @ @ @ LENS MONITOR REMOTE DC IN POWER ON 1 2 3 4 SEE INSTRUCTION MANUAL f MODE/SET button ● [MODE] Pressing this button each time will switch between the REC (record)* and PLAY (playback) modes. The default mode when the power is turned on is REC.
i FREEZE button While in the REC mode, press this button to capture a still image (freeze) of the images being outputted through the MONITOR terminal. At the same time, the still image is saved to the main unit memory. Pressing this button once more will cancel the still image and return to the camera images. Saving images to the main unit memory ( Z page 34) MEMO You can also set the unit to automatically cancel the still image after 5 seconds.
1. Introduction (continued) Explanation of terminals Power terminal (Mini DIN 8-pin, female) Lens terminal (Metal 12-pin, female) 10 7 8 9 6 @ @ @ @ @ @ Pin no. 3 6 4 2 2 7 3 5 1 8 4 12 5 11 1 Signal name Pin no. Signal name 1 NC 1 2 GND 2 3 NC 3 GND 4 NC 4 NC 5 GND 5 IRIS CONTROL 6 12V 6 12V DC 7 NC 7 IRIS POSITION 8 12V 8 IRIS AUTO /MANU 9 NC 10 NC 11 NC 12 NC Remoter terminal (Metal 10-pin, female) 1 8 7 2 10 9 3 6 5 Pin no.
Monitor terminal (D-sub 15-pin, female) 5 1 10 15 SCSI terminal (Half-pitch 50-pin, female) 25 1 50 26 6 11 Signal name Pin no. 1 R OUT 700mV, 75 Ω 2 G OUT 700mV, 75 Ω 3 B OUT 700mV, 75 Ω 4 GND 5 NC 6 R GND 7 G GND 8 B GND 9 NC 10 GND 11 GND 12 NC 13 Hs (3V(p-p) negative polarity Zo=100 Ω) 14 Vs (3V(p-p) negative polarity Zo=100 Ω) 15 NC 1 ~ 11 12 13 14 15 ~ 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Pin no.
2. Before recording Basic system 1 While checking the images from the camera on the monitor, output the images to an MO disk or printer.
Basic system 2 This is a system to record with this camera using a flash timed by an external freeze switch. AA-P700 AC ADAPTER AA-P700 POWER ON AC OFF AC adapter MONITOR SCSI REMOTE REMOTE DC IN C-MOUNT DIGITAL CAMERA KY-F70 VGA monitor Model name Microscope adapter CP700DSA PAPER FEED & CUT ALARM SHEET PAPER ] , MO disk drive COPY MITSUBISHI ONLINE DATA POWER OPEN Printer Flash Freeze switch CAUTION Use a 1/2 inch mount microscope adapter.
2. Before recording (continued) Inserting the lithium battery The lithium battery is used to back up the time and date data. Install the lithium battery before using the unit. < Install > Mini screwdriver (attached) Screws 1. Battery compartment @ @ @ @ @ @ DIG ITA L CA MER Y-F AK 70 Remove the screws (2 units) using the attached mini screwdriver, then open the cover. C-M OUN T 2. Completely insert the lithium battery in the direction of the arrow with the + side facing up. R202 C 5 3.
Mounting the lens Follow the procedure shown below when mounting an auto-iris lens. For further details, see the instruction manual of the lens. Camera head 3. Male Thread section -F70 RA KY Mount clamp ring TAL DIGI CAME T UN O C-M Lens 2. Female Lens remote control 1. Remove the lens mount cap. At this time, take caution so that dust do not enter inside the mount. 2.
2. Before recording (continued) Connecting the power Connect the DC IN terminal on the rear of the main unit and the TO CAMERA terminal of the AC adapter (AA-P700) with the attached power supply cable (2m). SCSI SEND AW/SEL MODE AA-P700 MENU UP DOWN REC SET PLAY FREEZE DC 12V=OUTPUT VIDEO OUTPUT @ @ @ @ @ AC@100V LENS MONITOR S(Y/C) OUTPUT REMOTE TO CAMERA DC IN ON 1 2 3 4 EITHER OUTPUT MAX 1.
Connecting a monitor Connect the PC monitor (VGA) to the MONITOR terminal on the rear of the main unit. SCSI SEND AW/SEL MODE MENU UP DOWN REC SET PLAY FREEZE LENS MONITOR REMOTE DC IN POWER ON 1 2 3 4 SEE INSTRUCTION MANUAL MONITOR terminal ● Before connecting, make sure that the power of all systems are turned off. Connecting with the power turned on may result in malfunction. ● For the connector, commercially available VGA video cable is recommended.
2. Before recording (continued) Connecting an MO drive unit It is possible to output image data stored in the main unit memory to an MO drive unit. ( Z Page 36 Saving images from the memory to an MO disk) Dip switches SCSI SEND AW/SEL MODE MENU @ @ @ @ @ @ UP DOWN REC SET PLAY FREEZE LENS MONITOR REMOTE DC IN ON 1 2 3 4 POWER SEE INSTRUCTION MANUAL SCSI terminal To directly connect the MO drive to the main unit, set the dip switches on the rear of the main unit as shown below.
Connecting a printer It is possible to directly output image data stored in the main unit memory to a printer.
2. Before recording (continued) Mounting the camera < Mounting method > Camera mounting screw hole Rotation prevention hole @ @ @ @ @ @ Camera mounting bracket ● When mounting the camera, use the camera mount screw hole located on the camera mounting bracket. ● When mounting the camera, use the rotation prevention hole to prevent the unit from falling and securely mount the unit.
Fall prevention Fall prevention wire chain 6mm Camera head Y-F70 ERA K L CAM DIGITA T OUN C-M Notes ● Special attention is required when mounting the unit to the wall or ceiling. Rather than attempting to do it yourself, request a qualified person to perform such installation. Falling of the unit may result in bodily injury. ● To prevent the unit from falling, connect the unit to a strong surface with a wire chain, etc.
3. Settings and adjustments for recording Setting the dip switches The type of PC monitor to use and the ID during SCSI connection are set using the dip switches. SCSI SEND AW/SEL MODE MENU UP DOWN REC MEMO Turn the power off before setting the dip switches. Setting the switches with the power on will not change the settings. SET PLAY FREEZE LENS MONITOR REMOTE Dip switches DC IN ON 1 2 3 4 POWER @ @ @ @ @ @ SEE INSTRUCTION MANUAL Monitor settings Dip switch no.
Menu settings VGA mode and lens settings are made from the menu screen. VGA mode settings Set whether to output semi-animation (7.5 frame/sec.) of 640 × 480 pixels or full-motion video (30 frames/sec.) of 640 × 240 pixels to the connected VGA monitor. - - - SYSTEM S ET T I NG - - ON SCREEN : MEMOR Y NUM FRZ D I SP L AY : ON SEND PR I OR ITY : MO : F I NE MON I TOR : 0.7 V BAR L EVE L : OF F NEGA MENU RE S ET . . V I DEO MEMORY CL EAR . . T I ME AD J UST Set MONITOR in the SYSTEM SETTING screen.
3. Settings and adjustments for recording (continued) Time and date settings MENU DOWN UP 1. Press the MODE button to enter the PLAY mode (PLAY LED on), then press the MENU button. The PLAY menu screen will be outputted through the MONITOR terminal. 2. Press either the UP or DOWN button and select TIME ADJUST (when selected, the TIME ADJUST display will become purple). Next, press the SET button to display the TIME ADJUST screen.
6. - - - T I ME AD J UST - - - OK will be displayed for approximately 3 seconds and the unit will return to the menu screen. O K OK display screen MEMO When setting the time and date, always set the seconds (00). Pressing the MENU button before setting the seconds will not change the set values.
3. Settings and adjustments for recording (continued) Monitor adjustment The color contrast, brightness, etc. are adjusted by sending built-in color bar signals of the main unit to the PC monitor. 1. Depending on the system, set the MONITOR mode to VGA or SXGA. (Set using the main unit dip switches) Monitor settings ( Z page 24) LENS 2. Connect the monitor and MONITOR terminal. POWER 3. Set dip switches 3 and 4 on the rear of the main unit to ON.
Focus adjustment This unit is not equipped with a back-focus feature. Adjust the back focus using the lens. Male Y-F70 RA K AME AL C DIGIT NT Focus ring OU C-M Female The default setting of the main unit shutter speed is 1/8. When difficult to focus, change the shutter speed to 1/30 using the procedure given below. 1. Press the MODE button to enter the REC mode (REC LED on). Next, lightly press the MENU button to display the REC mode quick menu screen. 2.
3. Settings and adjustments for recording (continued) White balance adjustment Since the color of light (light temperature) changes depending on the light source, readjust the white balance (AUTO WHITE) when the light source of the object changes. MENU DOWN UP 1. Press the MODE button to enter the REC mode (REC LED on), then press and hold the MENU button for at least 2 seconds to display the REC MENU screen. (If the button is pressed for less than 2 seconds, the REC mode quick menu will appear.
AW 6. After pressing the MENU button twice to return to the normal screen, place a white object with the same lighting conditions as the object to record, then zoom in to display white on the screen. 7. Press the AW (Auto White) button. ● When auto white is in operation, OPERATION will be displayed on the monitor screen. ● When the white balance is successfully set, OK will appear on the screen and the unit will return to the normal screen.
3. Settings and adjustments for recording (continued) White shading adjustment Even if the white balance is successfully achieved in the center of the screen, there may be times when white balance cannot be achieved at the top and bottom of the screen, resulting in the color of green and magenta becoming discolored. This is due to the characteristic of the lens and the adjustment of this is called the white shading adjustment. Perform the following after adjusting the white balance.
4. While watching the monitor screen, change LEVEL (R), LEVEL (G) and LEEL (B) using the UP and DOWN buttons. For each item, the color at the bottom weakens and the color at the top strengthens as the number becomes larger 5. When the adjustments of all channels (R, G and B channels) are completed, redo the white balance adjustment.
4. Basic operations Recording images to the main unit memory The main unit is capable of storing 5 images in the VGA mode and 4 images in the SXGA mode to the main unit memory. Exceeding the maximum number of images stored will replace the oldest image with the latest. 1. MODE SCSI @ @ @ @ @ @ SEND AW/SEL MODE MENU UP DOWN REC PLAY FREEZE FREEZE MEMO The unit will automatically enter the REC mode when the power is turned on.
Playing back images from the memory It is possible to play back images stored in the main unit memory. When in the VGA mode, images will be displayed in 640 × 480 pixels, regardless of whether in the FINE or DRAFT mode. 1. SEL MODE SCSI REC SEND AW/SEL MODE MENU UP DOWN SET PLAY FREEZE PLAY LED MEMO The character display contents of the monitor screen can be changed by selecting ON SCREEN in the SYSTEM SETTING screen.
4. Basic operations (continued) Saving images from the memory to an MO disk It is possible to save images stored in the main unit memory to an MO drive connected via the SCSI terminal when in the FREEZE or PLAY mode. (To output to an MO drive connected to a PC, see Page 64 7. Connecting to a PC) SEND MODE MENU m Set to either the FREEZE or PLAY mode. 1. Check to make sure that dip switches 1 and 2 are set to OFF as shown in the diagram on the left. 2. Press the SEND button.
Outputting images from the memory to a printer Use a printer with an SCSI input terminal. Print completed Print in operation Print confirmation It is possible to directly output images stored in the main unit memory to a printer connected via the SCSI terminal when in the FREEZE or PLAY mode. (To output to a printer connected to a PC, see Page 64 7. Connecting to a PC) PR I NT m Set to either the FREEZE or PLAY mode. 1.
4. Basic operations (continued) Clearing images from the memory This function will clear all images stored in the main unit memory. MENU DOWN UP 1. Press the MODE button to enter the PLAY mode (PLAY LED on), then press the MENU button to display the MENU screen. 2. Press the DOWN button , select VIDEO MEMORY CLEAR (displayed in purple when selected), then press the SET button to display the VIDEO MEMORY CLEAR screen. (The same screen can also be displayed by selecting 5.
4. V I DE O MEMORY C L EA R O K When completed, VIDEO MEMORY CLEAR OK will appear for approximately 3 seconds and the unit will return to the MENU screen. MEMO After clearing the entire memory in the PLAY mode, the unit will automatically enter the REC mode since no images will be available for playback. Memory cleared 5. Press the MENU button once more to return to the normal screen.
5. Various recording methods Recording a PC monitor Horizontal line noise will appear on the screen when attempting to record images on a PC monitor or display. To clear this noise, the main unit shutter speed must be adjusted with scan speed of the monitor. 1. Press the MODE button to enter the REC mode (REC LED on), then lightly press the MENU button to display the REC quick menu screen. 2. Press the DOWN button to select SHUTTER, then press SET (SHUTTER will be displayed in purple). 3.
Outputting negative images It is possible to change the video signal outputted through the MONITOR terminal of this unit as negative video. MENU DOWN UP SEND AW/SEL MODE UP Press the MODE button to enter the REC mode (REC LED on), then press the MENU button to display the REC MENU screen. 2. Use the DOWN button to select 5. SYSTEM SETTING (displayed in purple when selected), then press the SET button. The SYSTEM SETTING screen will appear. 3.
5. Various recording methods (continued) Synchronizing flash and FREEZE To activate the flash when inputting FREEZE, use the REMOTE terminal. The REMOTE terminal located in the rear is also used to freeze an image using an external device other than the FREEZE button on the rear of the main unit. Explanation of terminals ( Z page 12) ● In response to FREEZE input, KY-F70 outputs a flash signal for the CCD accumulation period of the next frame.
About ALC and EEI operations ALC refers to Automatic Level Control and EEI refers to shutter iris control. The Automatic Level Control (ALC) operates under dark lighting and the electronic shutter (EEI) operates under bright lighting. Furthermore, setting the IRIS mode to AUTO will synchronize sensitivity, iris and electronic shutter and appropriate signal level can be acquired automatically at all times.
6. Menu screen settings Menu screen flow There are 3 types of menu screens: PLAY menu screen, REC quick menu screen and REC normal menu screen. Normal screen Lightly press the @ @ @ @ @MENU @ button (less than 2 seconds) while in the REC mode. MEMO • Pressing the MENU button while in any of the menu screens will return the unit to the previous screen. • Press the MENU button for more than 2 seconds while in the REC mode will display not the REC quick menu but the REC normal menu screen.
- - - EXPOSURE - - I R I S MODE : AUTO AE L EVE L :0 : 128 I R I S L EVE L : NORMA L I R I S DETECT : FU L L I R I S AREA : ST EP SHUT TER :1/8 SPEED SENCET I V I TY : ST E P : I SO 1 0 0 L EVE L A LC MAX : I SO 4 0 0 Normal screen Press the MENU button for at least 2 seconds while in the REC mode.
6. Menu screen settings (continued) Setting procedure REC normal menu screen MENU DOWN UP MODE/SET 1. Press the MODE button to enter the REC mode (REC LED on), then press and hold the MENU for at least 2 seconds to display the REC normal menu screen. (If the MENU button is not pressed long enough, the REC mode quick menu will appear. In this case, press the MENU button to return to the normal screen, then press and hold the MENU button for at least 2 seconds.) 2.
- - - P L A Y / F REEZE MENU - - ON SCREEN : MEMORY NUM SEND PR I ORI TY: MO : 0.7 V BAR L EVE L MENU RESET . . V I DEO MEMORY CL EAR . . T I ME AD J UST . . PLAY menu screen 1. Enter the PLAY or FREEZE mode, then press the MENU button to display the PLAY menu screen. 2~5. Follow the steps described in the REC normal screen menu.
6. Menu screen settings (continued) EXPOSURE screen Menu item IRIS MODE AE LEVEL Function/variable range Default value Set depending on the used lens AUTO: when using an auto-iris lens MANUAL: when using a manual iris lens or no lens ATUO Used to adjust the video level when using auto iris, ALC 0 @ @ @ @ @ @and EEI. Raise the level: increase the number Lower the level: decrease the number [Variable range: –128 ~ 127] IRIS LEVEL Used to set the iris level when the IRIS MODE is set to MANUAL.
EXPOSURE screen (continued) Menu item Function/variable range Default value SHUTTER Used to set the shutter mode. STEP: the shutter speed can be changed using the SPEED submenu item. V.SCAN: used to clear the horizontal line noise when recording a PC monitor by adjusting to the scan speed of the monitor. The shutter can be changed in detail using the LEVEL submenu item. ( Z Page 42 Recording a PC monitor) EEI: Used to automatically change the shutter speed depending on the object brightness.
6. Menu screen settings (continued) EXPOSURE screen (continued) Menu item SENSITIVITY @ @ @ @ @ Function/variable range Used to set the sensitivity mode. STEP: the sensitivity can be changed using the LEVEL submenu item. ALS: the sensitivity si automatically changed by the brightness. Maximum sensitivity is set in the next @ ALC MAX menu item. V.SENS: the sensitivity can be set in detail using the LEVEL submenu item.
WHITE BALANCE screen Menu item Function/variable range Default value COLOR TEMP Used to set the basic color temperature of the white balance. 3200K: for use under low color temperature such as halogen lamps, etc. 5200K: for use under high color temperature such as the sunlight, etc. 3200K WHITE BAL Used to set the white balance mode. PRESET: the white balance is locked to the COLOR TEMP setting. (3200K:141/5200K:101) AUTO: Used when adjusting the white balance.
6. Menu screen settings (continued) WHITE BALANCE screen (continued) Menu item Function/variable range Default value Color temperatures when setting COLOR TEMP and WHITE BALANCE COLOR TEMP 3200K @ @ @ @ 5200K SHADING MODE E52 WHITE BALANCE Color temperature 2000K 3200K 5200K 15000K PRESET AUTO @MANUAL @ PRESET AUTO MANUAL Used to set whether to perform white shading adjustment. OFF: no white shading adjustment ADJUST: the white shading can be adjusted.
FREEZE screen Menu item CANCEL Function/variable range Used to set the cancellation method of FREEZE. MANUAL: freeze is cancelled by pressing the FREEZE button. AUTO: freeze is automatically cancelled after 5 seconds. Default value MANUAL PROCESS (1/3) screen Menu item DETAIL Function/variable range Default value Used to set whether to emphasize details.
6. Menu screen settings (continued) PROCESS (1/3) screen (continued) Menu item GAMMA @ @ @ @ @ LEVEL MASTER BLACK E54 Function/variable range Used to set whether the gamma curve to determine the reproduction of black is to be set using the standard value or available for change. NORMAL: the gamma curve is set using the standard value (0.45) @ADJUST: set when changing the gamma curve Default value NORMAL The gamma curve can be adjusted only when GAMMA is set to ADJUST.
PROCESS (2/3) screen Menu item Function/variable range Default value FLARE (R) Rch compensation of the black level when flaring effect occurs and the entire screen becomes washed out from the light entering the lens reflecting diffusely. Perform this function along with FLARE (B).
6. Menu screen settings (continued) PROCESS (2/3) screen (continued) Menu item COLOR MATRIX @ @ @ @ @ E56 Function/variable range Used to set whether to change the color matrix or use the standard value. OFF: the standard value of the color matrix is used. ADJUST: the color matrix becomes available for change. The following adjustments can only be made @ with this setting.
SYSTEM SETTING screen Menu item Function/variable range Default value ON SCREEN Used to set the text to display in the video signal outputted to the MONITOR terminal. ALC EEI: displays ALC and EEI status during the REC mode. MEMORY NUM: displays the memory image number during the PLAY mode. BOTH: displays both sensitivity during REC mode and memory image number during PLAY mode. OFF: no text is displayed for either REC mode or PLAY mode.
6. Menu screen settings (continued) SYSTEM SETTING screen (continued) Menu item BAR LEVEL NEGA @ @ Function/variable range Default value Used to set the level of the color bar signal outputted from the MONITOR terminal of this unit. 0.7V: outputs 0.7V color bar signals 0.58V: outputs 0.58V color bar signals 0.7V @ @ @ @It is possible to change the outputted signals to the MONI- OFF TOR terminal to negative signals.
Menu screen of the PLAY mode Menu item Function/variable range Default value ON SCREEN Used to set the text to display in the video signal outputted to the MONITOR terminal. ALC EEI: displays ALC and EEI status during the REC mode. MEMORY NUM: displays the memory image number during the PLAY mode. BOTH: displays both sensitivity during REC mode and memory image number during PLAY mode. OFF: no text is displayed for either REC mode or PLAY mode.
6. Menu screen settings (continued) REC mode quick menu screen Menu item AE LEVEL Function/variable range Used to adjust the video level when using auto iris, ALC and EEI. Raise the level: increase the number Lower the level: decrease the number [Variable range: –128 ~ 127] Default value 0 @ @ @ @ @ @ IRIS LEVEL Used to set the iris level when the IRIS MODE is set to MANUAL.
Menu item Function/variable range Default value SPEED MEMO • In areas which the power supply frequency is 50Hz, setting the unit to 1/100 can reduce flickering when recording under florescent lighting. • There may be shortage of light when increasing the shutter speed. In this case, adjust the iris or sensitivity. Special attention is required for the picture quality when raising the sensitivity since images may become distorted. SENSITIVITY Used to set the sensitivity mode.
6. Menu screen settings (continued) Resetting settings This function is used to initialize all settings other than the time and date. MENU DOWN UP 1. Press the MODE button to enter the PLAY mode (PLAY LED on), then press the MENU button to display the MENU screen. 2. Press the DOWN button to select MENU RESET (displayed in purple when selected), then press the SET button. The MENU RESET screen will appear. (The MENU RESET screen can also be displayed by selecting 5.
4. When all values are reset to their default settings, MENU RESET OK message will appear for 3 seconds, then the unit will return to the MENU screen. 5. Press the MENU once more to return to the normal screen.
7. Connecting to a PC Compatible systems 1 With SCSI connection, still images of the main unit can be exported to a PC while checking the recorded images on a VGA monitor. ● The main unit can be controlled from the PC. For this system, the PC is the host (initiator) and the main unit (digital camera) is the target. ● Images exported to a PC can be processed using the Photoshop application software.
Compatible systems 2 It is possible to process SXGA compatible images of this unit directly on a PC using a capture board. Images can be processed while viewing still images and camera video of this unit on a PC monitor. ● Images can be checked on a SXGA monitor when using an SXGA compatible capture board. ● Images can be checked on a VGA monitor when using a VGA compatible capture board.
8. Others Specifications Imaging device: 1/2 inch IT CCD × 3 Scanning method: Progressive scanning Available no. of pixels: 1.45 million pixels (1392 (H) × 1040 (V)) Effective no. of pixels: 1360 × 1024 Color separation method: Dichroic prism method @ @ ratio: @ @ Aspect 4:3 @ @ V.SCAN: 1/30 ~ 1/5906.8 Detail compensation method: both H and V Lens mount: C mount Analog output: R/G/B signal: 0.7V (p-p), 7.5 Ω Output signals: (Choice of 1) ~ 1360 × 1024 pixels, 7.5 frames/sec.
External dimensions (unit: mm) 88 80 70 150 142.5 1 C-MOUNT DIGITAL CAMERA KY-F70 41.5 14 1/4 inch screw Design and specifications are subject to change without notice.
VICTOR COMPANY OF JAPAN, LIMITED is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD. is a registered trademark in Japan, the U.S.A., the U.K. and many other countries.