COLOR VIDEO MONITOR FRANÇAIS INSTRUCTIONS DEUTSCH TM-H1950CG TM-H1750CG ENGLISH BEDIENUNGSANLEITUNG : FARB-VIDEO-MONITOR MANUEL D’INSTRUCTIONS : MONITEUR VIDÉO COULEUR MANUALE DI ISTRUZIONI : MONITOR VIDEO A COLORI INSTRUCCIONES : MONITOR DE VIDEO A COLOR !"#$%&'(&) ITALIANO For Customer Use: Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference.
INSTRUCTIONS TM-H1950CG TM-H1750CG Thank you for purchasing this JVC color video monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor’s capabilities. LCT1025-002A-H(EN) 3 02.4.
SAFETY PRECAUTIONS In order to prevent any fatal accidents caused by misoperation or mishandling the monitor, be fully aware of all the following precautions. WARNINGS To prevent fire or shock hazard, do not expose this monitor to rain or moisture. Dangerous high voltages are present inside the unit. Do not remove the back cover of the cabinet. When servicing the monitor, consult qualified service personnel. Never try to service it yourself. WARNING : THIS APPARATUS MUST BE EARTHED.
POWER CONNECTION The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power cord designated to ensure Safety and EMC regulations of each countries. Power cord Power supply voltage : AC 120 V Countries : U.S.A.
CONTROLS AND FEATURES FRONT VIEW 1 CHROMA CONTRAST VOLUME/SELECT MENU UNDER SCAN COLOR OFF BLUE CHECK ASPECT A C SLOT D B POWER 15 CHROMA CONTRAST TM-H1950CG PHASE VOLUME/SELECT MENU UNDER SCAN COLOR OFF BLUE CHECK ASPECT BRIGHT A B C SLOT D PHASE BRIGHT 2 3 POWER INPUT SELECT 4 5 6 7 8 9 10 11 12 13 14 INPUT SELECT (Front view of TM-H1950CG shown) 1 Tally lamp 8 Blue Check button [BLUE CHECK] Lights when the tally control signal is ON.
REAR VIEW VIDEO A IN OUT 16 SLOT 18 REMOTE 17 VIDEO B 19 IN OUT VIDEO A IN OUT VIDEO B IN IN IN 20 Y/C OUT Y/C OUT AUDIO A IN OUT AUDIO B IN OUT OUT AUDIO A (Rear view of TM-H1950CG shown) 21 OUT AUDIO B 22 IN 20 Video B (Y/C) terminals [VIDEO B Y/C IN/OUT] OUT 16 Input card slot (SLOT) Optional input cards can be installed in this slot. Input cards are not provided when you purchase this monitor.
CONTROLS AND FEATURES (cont’d) REAR VIEW SLOT 25 To AC outlet (120 V AC, 50 Hz/60 Hz) REMOTE For U.S.A. and Canada VIDEO A To AC outlet (230 V AC, 50 Hz/60 Hz) IN OUT VIDEO B IN 25 IN OUT Y/C OUT AUDIO A IN OUT AUDIO B For Europe IN OUT 25 (Rear view of TM-H1950CG shown) 24 For the United Kingdom 23 Main power switch Press the switch to turn the main power ON or OFF.
CONTROLS AND FEATURES (INPUT CARD: OPTIONAL) COMPONENT/RGB INPUT CARD (OPTIONAL: IF-C01COMG) 1 Video input/output terminals Input (IN) and output (OUT) terminals for component (color deference) or RGB signals. The IN and OUT terminals are bridge-connected. (When no cable is connected to the OUT terminal, the input signal is automatically terminated.
PREPARATION INSTALLING THE INPUT CARD 1. Turn off the Color Video Monitor’s main power and unplug the power cable from the AC outlet. 2. Unscrew the screws and remove the slot cover from the slot (on the rear side of the monitor) in which you are going to install the card. SLOT Rear side of the TM-H1950CG color video monitor REMOTE Slot cover VIDEO A IN OUT VIDEO B IN IN OUT Y/C 3.
ATTACHING THE POWER CORD HOLDER The provided Power Cord Holder prevents the AC power cord from being accidentally disconnected from the AC inlet. The Power Cord Holder consists of two parts; a case and cover. 1. Attach the Power Cord Holder case to the AC inlet on the back of the monitor with 2 screws (provided). Caution: Use only the provided screws. ENGLISH 2. Attach the Power Cord Holder cover to the AC power cord. Press the cover until it clicks. 3.
HOW TO HANDLE BASIC OPERATIONS BASIC OPERATION STATUS indication (PAL or NTSC) 1. Press the main power switch to turn on the power. 2. Press the POWER switch to turn on the power. POWER 3. Press the INPUT SELECT buttons to choose input. Select video/audio signals input to terminals on the rear panel. The selected button lights in green. A B PAL ON : Power turns ON. (Power indicator: lit) Green : The main power is ON, and the monitor’s power is ON (in the normal operation mode). OFF : Power turns OFF.
VIDEO SIGNAL CONTROLS Use these buttons for video signal control. UNDER SCAN Press the UNDER SCAN button to reduce the size of display area so that the whole picture is displayed on screen. Use to check the picture frame. COLOR OFF To display a black and white picture, press the COLOR OFF button to input the luminance signal only. Use to check noise in the luminance signal or for white balance adjustment. Note: ● No effect with RGB input.
HOW TO USE THE MENU FUNCTIONS DISPLAY AND SELECTION IN THE
DISPLAY AND SELECTIONS IN THE MODE (SETTING) screen You can set the following set-up menu items. • WHITE BALANCE • CONTROL LOCK • STATUS DISPLAY 1 • REMOTE SYSTEM • INPUT REMOTE 4 PICTURE SUB ADJ. H. POSITION V. POSITION WHITE BALANCE CONTROL LOCK STATUS DISPLAY REMOTE SYSTEM INPUT REMOTE Notes: ● Parameters for PICTURE SUB ADJ., H. POSITION and V.
HOW TO USE THE MENU FUNCTIONS (cont’d) Set-up menu items Purpose PICTURE SUB ADJ. Settings Image sub adjustment Selects CONTRAST/BRIGHT/CHROMA/PHASE. The selected setting screen is shown. Select the function display for adjustment. Adjusts contrast. –10 –9 • • –01 00 +01 • • +09 +10 BRIGHT Adjusts brightness. – 10 –9 • • – 01 00 +01 • • +09 +10 CHROMA Adjusts color density. *1 –10 –9 • • –01 00 +01 • • +09 +10 PHASE Adjusts hue.
HOW TO INITIALIZE THE SETTING SCREEN DISPLAY AND SELECTIONS IN THE RESET MODE You can set and screen items, picture adjustment items and the volume level to their factory-set (initial) values. RESET screen RESET Are you “Yes” then “No” then 1. Press the Power ( ) switch to turn the power OFF (activate the standby mode). sure ? <+> POWER APERTURE ADJ. BAR POSI COLOR TEMP COLOR SYSTEM COMPO. LEVEL RUSH DELAY PICTURE SUB ADJ.
BASIC CONNECTION EXAMPLE Notes: • Before connecting your system, make sure that all units are turned off. • The illustration below shows some examples of different connections. Terminal connections may differ depending on the component connected. Be sure to refer to the instructions provided with the unit(s) you are connecting. • Each pair of input (IN) and output (OUT) terminals are bridge-connected.
VIDEO B (Y/C) Connection Example (Select Input B (Y/C)) VIDEO A IN OUT VIDEO B Video Camera IN OUT Y/C (S-video) (Y/C (S-video) signal cable) VCR IN Y/C Video Monitor Y/C (S-video) (Y/C (S-video) signal cable) OUT AUDIO A Audio (Audio signal cable) OUT AUDIO B IN Video Monitor Audio OUT (Audio signal cable) : Signal Flow ENGLISH IN VCR 17 LCT1025-002A-H(EN) 19 02.4.
HOW TO USE EXTERNAL CONTROL ABOUT EXTERNAL CONTROL This monitor is provided with an external control terminal. MAKE (make contact) or TRIG. (trigger) system can be selected by the setting of REMOTE SYSTEM in the . MAKE (make contact system) : The functino is controlled by short-circuiting or disconnecting each control terminal with pin 15 (GND). TRG. (trigger system) : The function is controlled by short-circuiting with pulses (for about 1 second) (short-circuit/open with the 15th pin GND).
TROUBLESHOOTING Solutions to common problems related to your monitor are described here. If none of the solutions presented here solves the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance. Points to be checked No power supply. Measures (Remedy) Is the power plug loosened or disconnected? Firmly insert the power plug. Is the main power turned OFF? Turn the main power ON. (See page 6.
SPECIFICATIONS MODEL TM-H1950CG TM-H1750CG Type Color video monitor Color system PAL, NTSC (3.58) Picture tube 49 cm (19") measured diagonally, 90° deflection, in-line gun, trio-dot type (phosphor dot-trio pitch 0.27 mm) Effective screen size 44 cm (17") measured diagonally, 90° deflection, in-line gun, trio-dot type (phosphor dot-trio pitch 0.27 mm) Width 365.8 mm (14-5/8") Height 274.3 mm (10-7/8") Diagonal 457.2 mm (18") Width Height Diagonal 327.5 mm (12-7/8") 246.2 mm (9-5/8") 407.
Dimensions [TM-H1950CG] Unit : mm (inch) < Side View > < Front View > 496 (19-5/8") 485 (19-1/9") 440 (17-3/8") 1.5 (1/16") VOLUME/SELECT MENU UNDER SCAN COLOR OFF BLUE CHECK ASPECT A BRIGHT B C SLOT D POWER INPUT SELECT 380.4 (15") 336 (13-1/4") 95.7 (3-7/8") 5 (1/4") PHASE 5 (1/4") CHROMA CONTRAST TM-H1950CG 195.5 (7-3/4") 284.3 (11-1/4")* 375 (14-7/8") 375 (14-7/8")* ENGLISH ø 20 (7/8") * Asterisks (*) are used to indicate front panel dimensions.
Y/C (Mini DIN 4 pin) terminal specification 2 4 1 3 OUT 2 4 1 3 Pin No. IN Y/C Signal 1 GND (Y) 2 GND (C) 3 Y 4 C APPENDIX: CONNECTION EXAMPLES FOR THE SDI INPUT CARD ● To use the SWITCHED OUT terminal, the main power must be ON. (Unlike a bridged output, this connector outputs relocked digital signals.) ● Signal output from the SWITCHED OUT terminal can be changed by selecting INPUT C (SDI 1) or INPUT D (SDI 2). You can use the front panel buttons or do it via external control.
MEMO MEMO LCT1025-002A-H(EN) 25 02.4.
TM-H1950CG/TM-H1750CG COLOR VIDEO MONITOR VICTOR COMPANY OF JAPAN, LIMITED Printed in Thailand 0602-Y-U-JMT © 2002 VICTOR COMPANY OF JAPAN, LIMITED LCT1025-002B-H(CH) 25 02.6.