9" Portable On-camera LCD Monitor User Manual Model: DT-X91F HDSDI&HDMI, Waveform, Audio meter, Focus assist DT-X91H 3GSDI&HDMI DT-X91C HDMI
Please read this User Manual throughout before using. Preface Congratulations on your purchase of this product. Please read this user manual carefully. 1 . All internal technologies of this product are protected, including device, software and trademark. Reproduction in whole or in part without written permission is prohibited. 2 . All brands and trademarks are protected and other relative trademarks in this user manual are the properties of their respective owners.
Maintenance Monitor 1. Please keep the signal terminals and the cooling vent away from knife-edge, metal or liquid in order to avoid short-circuit and damage. 2. Please don't try to disassemble any parts of the monitor by yourself, which would probably damage the monitor and do harm to human body, and it will cause the invalidation of product warranty. 3. Please don't touch the screen with your fingers, which would probably deface the screen. 4.
1. Features DT-X91F ◆ High resolution 9” LCD Panel 16:9, 1280×800, 16.77 million colors ◆ Multiple inputs 2 HD/SD-SDI, 1 HDMI and 1 Composite input. ◆ Loop through outputs 2 HD/SD-SDI and 1 HDMI loop through output. ◆ HDMI converted to SDI output Supported HDMI formats: 480i / 576i / 720p (50, 59.94, 60) / 1080i (50, 59.94, 60) / 1080P (23.98 24, 25, 29.97, 30), and the output SDI will embed the audio (48KHz) from HDMI.
DT-X91H ◆ High resolution 9” LCD Panel 16:9, 1280×800, 16.77 million colors ◆ 3Gbps SDI support Accepts 3G/HD/SD-SDI input. ◆ Multiple inputs ◆ ◆ ◆ ◆ DSLR scale zoom in The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective image scale full screen on the monitor. User definable function keys There are 2 function keys on the monitor front panel, that permit users to define shortcuts for the various functions.
2. Panel Instruction DT-X91F Front view ⑴ PHONE: Earphone jack, for SDI embedded audio, HDMI embedded audio monitoring ⑵ POWER: Power on/off Connect with power cable, press the “POWER” and the power indicator is turned on and the monitor will be switched on and get into normal working status. Press the “POWER” again, the indicator is turned off and monitor is switched off. Disconnect with power cable or battery if the monitor will not be used for a period of time.
Rear view ⑴ DC 12V IN: Connect with DC12V 4-pin XLR power adapter. ⑵ TALLY Light: Red, Green and Yellow 3-color TALLY indicator ⑶ Battery mount: Connect with SSL-JVC50 battery (optional) to power the monitor.
DT-X91H Front view ⑴ PHONE: Earphone jack, for SDI embedded audio, HDMI embedded audio and analog audio monitoring ⑵ POWER: Power on/off Connect with power cable, press the “POWER” and the power indicator is turned on and after 10 seconds, the monitor will be switched on and get into normal working status. Press the “POWER” again, the indicator is turned off and monitor is switched off. Disconnect with power cable or battery if the monitor will not be used for a period of time.
Rear view ⑴ ⑵ ⑶ ⑷ DC 12V IN: Connect with DC12V 4-pin XLR power adapter. Battery mount: Connect with SSL-JVC50 battery (optional) to power the monitor.
DT-X91C Front view ⑴ PHONE: Earphone jack, for HDMI embedded audio and analog audio monitoring ⑵ POWER: Power on/off Connect with power cable, press the “POWER” and the power indicator is turned on and after 10 seconds, the monitor will be switched on and get into normal working status. Press the “POWER” again, the indicator is turned off and monitor is switched off. Disconnect with power cable or battery if the monitor will not be used for a period of time.
Rear view ⑴ DC 12V IN: Connect with DC12V 4-pin XLR power adapter. ⑵ Battery mount: Connect with SSL-JVC50 battery (optional) to power the monitor. ⑶ CVBS IN: Composite video input (BNC connector) ⑷ HDMI-LOOP: HDMI loop through output ⑸ HDMI-IN: HDMI input ⑹ TALLY controlling port (RS-232): terminal description is as follows: Terminal Description 1 2 Y 3 G 4 R 5 6 7 GND 8 GND The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting.
3. Menu Operation Press “MENU” and it will display menu system Revolve “OK” to select an item. The selected item will be highlighted display. Press “OK” to enter the selected item. Under menu system, press “MENU” to back to previous menu. The menu will automatically save and quit if it remains idle. 4.
6. OSD Settings Submenu The OSD Settings Submenu includes: ⑴ LANGUAGE: Menu language English / Chinese selection ⑵ H-POSITION: Menu horizontal position (0-100) adjustment, real-time preview, default value: 50, center. ⑶ V-POSITION: Menu vertical position (0-100) adjustment, real-time preview, default value: 50, center. ⑷ DURATION: Menu timeout setting Set a time (in seconds) in which the menu will automatically quit if remains idle. Default: 10 seconds; Range: 5 seconds to 60 seconds. 7.
9. FUNCTION KEY Settings Submenu The F KEY Settings Submenu is to define Function Keys on the front keyboard. The DT-X91F has 3 function keys: F1, F2 and F3; The DT-X91H and DT-X91C has 2 function keys: F1 and F2.
10. Specifications LCD Performance Size 9.0 inches Resolution 1280×RGB×800 Aspect ratio 16:9/4:3 Color system NTSC/PAL Brightness 250cd/m2 Contrast 700:1 Color 16.77 million colors Viewing angle H/V:140/120 Video Format SMPTE-425M ** SMPTE-274M SDI * 1080p (60 / 59.94 / 50) 1080i (60 / 59.94 / 50) 1080p (30 / 29.97 / 25 / 24 / 23.98) SMPTE-RP211 1080psf (30 / 29.97 / 25 / 24 / 23.98) SMPTE-296M 720p (60 / 59.94 / 50) SMPTE-125M 480i (59.94) ITU-R BT.
This model is manufactured, warranted and supported by SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC, and distributed in North America by JVC Professional Video Products. To obtain service or for further information, please contact: SWIT Electronics USA, LLC. Address: 4300 Stevens Creek Blvd., Suite 230, San Jose, CA 95129 Toll free: 1 866 986-SWIT (7948) • Tel: 408 260-8258 Email: info@swit.us • Website: www.swit.