ENGLISH FRANÇAIS FM CORDLESS HEADPHONES CASQUE FM SANS FIL AURICULARES INALÁMBRICOS FM ESPAÑOL HA-W600RF-J/C For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No. INSTRUCTIONS MANUEL D’INSTRUCTIONS MANUAL DE INSTRUCCIONES LNT0066-001A HAW600RF_J.indb 3 06.6.
Warnings, cautions and others Mises en garde, precautions et indications diverses Avisos, precauciones y otras notas FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not approved by JVC could void user’s authority to operate the equipment.
IC INFORMATION This device complies with RSS-210 of the IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation of the device. CAUTION: Changes or modifications not approved by JVC could void user’s authority to operate the equipment. Contact Address: JVC CANADA INC.
IMPORTANT CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. ATTENTION: POUR PREVENIR LES CHOCS ELECTRIQES NE PAS UTILISER CETTER FICHE AVEC UN PROLONGATEUR, UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT. (1) This device may not cause interference.
FEATURES • Call Function–Call headphone user with “CALL” button on base station (transmitter) • Reception range up to 50 m/164 ft.
ENGLISH Precautions Important cautions CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, cover or cabinet. 2. Do not expose this appliance to rain or moisture. Precautions Installation • Select a place which is level, dry and neither too hot nor too cold (between 0°C and 35°C (32°F and 95°F)). • Keep away from direct sunlight. • Do not put it too close to a heater. • Indoor use only.
ENGLISH Parts identification See pages in parentheses for details. Base station (transmitter and battery charging unit) Back side 6 * 1 1 2 3 4 23 4 7 8 The battery charging terminal on the base station is covered with the protection cap when purchasing. Take off the cap before charging.
ENGLISH Connection Be sure to connect the AC adaptor after all other connections are complete. 1 Connect the base station to the AV equipment. 2 Connect the AC adaptor to the base station. 3 Connect the AC adaptor to the AC outlet. 2 1 1 Conversion cord for stereo pin jack (supplied) Connection cord (supplied) TV, audio amplifier, VCR, DVD player, PC, etc. AC adaptor (supplied) Plug adaptor for 6.3 mm (0.
1 Take off the ear pad of the right headphone. 4 5 Put on the battery covers. Put on the ear pad. 1 Insert the hem of the ear pad into the slit on the headphone. 2 Take off the battery covers. 3 Install the batteries. Match the polarity (+ and –) on the batteries with the + and – marking on the battery compartments. • Insert the – terminal of the battery at first. Be sure to use the supplied exclusive battery.
ENGLISH Charging the battery The base station works as the battery charging unit. Charge the rechargeable battery before starting to use the headphones. You can continuously use the headphones for about 10 hours after full battery charge. 1 Make sure that the headphones are turned off. You cannot charge the battery of the headphones when the headphones are turned on. Press POWER to turn the Power indicator off. 2 Put on the headphones on the base station so that their charging terminals contact firmly.
• No sound is heard while Auto Tuning. It takes a few seconds to tune in. • Press AUTO SCAN when the sound does not come out properly. Listening to the sound from the base station The base station works as the FM transmitter and send sound to the headphones. Precaution Turn down the volume of the headphones with the VOL dial before turning on its power to avoid excessive volume. 1 Start playback on the AV equipment connected with the base station.
ENGLISH Basic operations Selecting a better reception channel Call through the base station When the playback sound is noisy, you can choose one of the other two channels to transmit signals on the base station. • The white noise may come out when switching the channel. Take off the headphones when switching the channel. You can call the one using the headphones with the microphone on the base station. 1 2 3 1 Press and hold CALL on the base station. The playback sound is interrupted.
What appears to be trouble is not always serious. Check the following points before calling a service center. Symptom Cause/Remedy No sound comes out at all. • Turns on the power of the headphones. • Start playback on the AV equipment connected to the base station. • Check the connection between the base station and the AV equipment. • Turns up the volume of the headphones or the connected AV equipment to an appropriate level. • Fully charge the headphones’ battery. No sound comes out from R-channel.
ENGLISH Specifications General Specifications Modulation system: Stereo frequency modulation system Carrier frequency: 912.0 MHz (Channel 1) 912.5 MHz (Channel 2) 913.0 MHz (Channel 3) Usable area (distance to reach): Max. 50 m (164 ft.) (using JVC measurement systems, under controlled ambient conditions) Frequency response: 25 Hz – 13,000 Hz Distortion: Less than 3% (at 1 kHz) Transmitter (J22320-001) Power requirements: DC 12 V (with the exclusive AC adaptor) Audio input terminals: 3.5 mm (0.13˝) dia.
HA-W600RF-J/C FM CORDLESS HEADPHONES © 2006 Victor Company of Japan, Limited HAW600RF_J.indb 2 Printed in China LNT0066-001A 06.6.
ENGLISH NEDERLANDS DEUTSCH FM CORDLESS HEADPHONES FUNKKOPFHÖRER DRAADLOZE FM-HOOFDTELEFOON CASQUE FM SANS FIL CUFFIE SENZA FILO FM TRÅDLÖSA FM-HÖRLURAR SVENSKA ITALIANO FRANÇAIS HA-W600RF-G INSTRUCTIONS BEDIENUNGSANLEITUNG GEBRUIKSAANWIJZING MANUEL D’INSTRUCTIONS ISTRUZIONI BRUKSANVISNING HAW600_G.indb 3 LNT0067-001A 06.6.
FM CORDLESS HEADPHONES 863MHz — 865 MHZ THIS DEVICE IS INTENDED FOR USE IN THESE COUNTRIES: DIESES GERÄT IST FÜR DEN GEBRAUCH IN DEN FOLGENDEN LÄNDERN VORGESEHEN: DIT APPARAAT IS BEDOELD VOOR GEBRUIK IN DEZE LANDEN: DISPOSITIF PREVU POUR ETRE UTILISE DANS LES PAYS SUIVANTS: QUESTO DISPOSITIVO È DESTINATO PER L’USO IN QUESTI PAESI: DENNA APPARAT ÄR AVSEDD FÖR BRUK I DESSA LÄNDER: English Hereby, JVC, declares that this HA-W600RF is in compliance with the essential requirements and other relevant provision
Dear Customer, ENGLISH Cher(e) client(e), FRANÇAIS This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety. Cet appareil est conforme aux directives et normes européennes en vigueur concernant la compatibilité électromagnétique et à la sécurité électrique.
Information for Users on Disposal of Old Equipment ENGLISH [European Union] This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of-life. Instead, the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment, recovery and recycling in accordance with your national legislation.
Informatie voor gebruikers over het weggooien van oude apparatuur NEDERLANDS [Europese Unie] Deze markering geeft aan dat de elektrische en elektronische apparatuur bij het einde van de gebruiksduur niet bij het huishoudelijk afval mag worden gegooid. Het product moet in plaats daarvan worden ingeleverd bij het relevante inzamelingspunt voor hergebruik van elektrische en elektronische apparatuur, voor juiste verwerking, terugwinning en hergebruik in overeenstemming met uw nationale wetgeving.
Informazioni per gli utenti sullo smaltimento delle apparecchiature obsolete ITALIANO [Unione Europea] Questo simbolo indica che l’apparecchiatura elettrica ed elettronica a cui è relativo non deve essere smaltita tra i rifiuti domestici generici alla fine della sua vita utile.
ENGLISH This product’s performance would be degraded under a strong electro-static environment. And the function would be self-recoverable after the above case. This product’s performance would be degraded since the disturbance from the mains cord. And the function would be self-recoverable after the above case. DEUTSCH Die Leistung dieses Produkts würde sich in einer stark elektrostatisch geladenen Umgebung verschlechtern. Und die Funktion würde sich nach dem obigen Fall selbst wiederherstellen.
“SOME DO’S AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical apparatus, care must be taken if you are to obtain the best results and safety is to be assured. ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Do read the operating instructions before you attempt to use the equipment.
FEATURES • Reception range up to 100 m (using JVC measurement system) • Auto Tuning–Headphones automatically tunes in to the base station (transmitter) as it turns on • On Stand Charging–Rechargeable system with the exclusive Ni-MH battery that requires no charge cable • Auto Power On/Off transmitter • “PLL” Stabilized Transmission Technology • Auto-level control circuit that automatically adjusts signals to the appropriate modulation level • Large 40 mm dia.
ENGLISH Precautions Important cautions CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, cover or cabinet. 2. Do not expose this appliance to rain or moisture. Precautions Installation • Select a place which is level, dry and neither too hot nor too cold (between 0°C and 35°C). • Keep away from direct sunlight. • Do not put it too close to a heater. • Indoor use only. Power cord • Do not handle the power cord with wet hands! • Do not bend the power cord sharply.
ENGLISH Parts identification See pages in parentheses for details.
ENGLISH Connection Be sure to connect the AC adaptor after all other connections are complete. 1 Connect the base station to the AV equipment. 2 Connect the AC adaptor to the base station. 3 Connect the AC adaptor to the AC outlet. 2 1 1 Conversion cord for stereo pin jack (supplied) Connection cord (supplied) AC adaptor (supplied) TV, audio amplifier, VCR, DVD player, PC, etc. Plug adaptor for 6.
1 Take off the ear pad of the right headphone. 4 5 Put on the battery covers. Put on the ear pad. 1 Insert the hem of the ear pad into the slit on the headphone. 2 Take off the battery covers. 3 Install the batteries. Match the polarity (+ and –) on the batteries with the + and – marking on the battery compartments. • Insert the – terminal of the battery at first. Be sure to use the supplied exclusive battery.
ENGLISH Charging the battery The base station works as the battery charging unit. Charge the rechargeable battery before starting to use the headphones. You can continuously use the headphones for about 10 hours after full battery charge. 1 Make sure that the headphones are turned off. You cannot charge the battery of the headphones when the headphones are turned on. Press POWER to turn the Power indicator off. 2 Put on the headphones on the base station so that their charging terminals contact firmly.
• No sound is heard while Auto Tuning. It takes a few seconds to tune in. • Press AUTO SCAN when the sound does not come out properly. Listening to the sound from the base station The base station works as the FM transmitter and send sound to the headphones. Precaution Turn down the volume of the headphones with the VOL dial before turning on its power to avoid excessive volume. 1 Start playback on the AV equipment connected with the base station.
ENGLISH Basic operations Selecting a better reception channel When the playback sound is noisy, you can choose one of the other two channels to transmit signals on the base station. • The white noise may come out when switching the channel. Take off the headphones when switching the channel. 1 Slide the CHANNEL selector on the back side of the base station to select another channel. 2 Press AUTO SCAN on the headphones to tune in to the new channel. 3 Repeat Steps 1 and 2 to select the best channel.
What appears to be trouble is not always serious. Check the following points before calling a service center. Symptom Cause/Remedy No sound comes out at all. • Turns on the power of the headphones. • Start playback on the AV equipment connected to the base station. • Check the connection between the base station and the AV equipment. • Turns up the volume of the headphones or the connected AV equipment to an appropriate level. • Fully charge the headphones’ battery. No sound comes out from R-channel.
ENGLISH Specifications General Specifications Modulation system: Stereo frequency modulation system Carrier frequency: 863.5 MHz (Channel 1) 864.0 MHz (Channel 2) 864.5 MHz (Channel 3) Usable area (distance to reach): Max. 100 m (using JVC measurement systems, under controlled ambient conditions) Frequency response: 25 Hz – 13,000 Hz Distortion: Less than 3% (at 1 kHz) Transmitter (J22321-001) Power requirements: DC 12 V (with the exclusive AC adaptor) Audio input terminals: 3.5 mm dia.
HA-W600RF-G FM CORDLESS HEADPHONES © 2006 Victor Company of Japan, Limited HAW600_G.indb 2 Printed in China LNT0067-001A 06.6.
FM CORDLESS HEADPHONES HA-W600RF-B INSTRUCTIONS LNT0068-001A HAW600RF_B.indb 3 06.6.
FM CORDLESS HEADPHONES 863MHz — 865 MHZ THIS DEVICE IS INTENDED FOR USE IN THESE COUNTRIES: English Hereby, JVC, declares that this HA-W600RF is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish JVC vakuuttaa täten että HA-W600RF tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety. European representative of Victor Company of Japan, Limited is: JVC Technology Centre Europe GmbH Postfach 10 05 52 61145 Friedberg Germany Information for Users on Disposal of Old Equipment [European Union] This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of-life.
“SOME DO’S AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical apparatus, care must be taken if you are to obtain the best results and safety is to be assured. ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Do read the operating instructions before you attempt to use the equipment.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.
Precautions Important cautions CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, cover or cabinet. 2. Do not expose this appliance to rain or moisture. Precautions Installation • Select a place which is level, dry and neither too hot nor too cold (between 0°C and 35°C). • Keep away from direct sunlight. • Do not put it too close to a heater. • Indoor use only. Power cord • Do not handle the power cord with wet hands! • Do not bend the power cord sharply.
Parts identification See pages in parentheses for details. Base station (transmitter and battery charging unit) Back side 4 1 2 5 6 3 1 CHARGE indicator (6) 2 POWER indicator (7) 3 Battery charging terminal (6) 4 CHANNEL selector (8) 5 AUDIO IN jack (4) 6 DC IN jack (4) Headphones Right Left 1 2 3 4 5 6 7 1 2 AUTO SCAN button (7, 8) AUTO SCAN indicator (7) VOL (volume) (7) Ear pad (5) Battery charging terminal (6) POWER button (6, 7) POWER indicator (6, 7) 3 6 4 4 7 5 3 HAW600RF_B.
Connection Be sure to connect the AC adaptor after all other connections are complete. 1 Connect the base station to the AV equipment. 2 Connect the AC adaptor to the base station. 3 Connect the AC adaptor to the AC outlet. 2 1 1 Conversion cord for stereo pin jack (supplied) Connection cord (supplied) TV, audio amplifier, VCR, DVD player, PC, etc. AC adaptor (supplied) Plug adaptor for 6.
Battery installation 1 Take off the ear pad of the right headphone. 4 5 Put on the battery covers. Put on the ear pad. 1 Insert the hem of the ear pad into the slit on the headphone. 2 Take off the battery covers. 3 Install the batteries. Match the polarity (+ and –) on the batteries with the + and – marking on the battery compartments. • Insert the – terminal of the battery at first. Be sure to use the supplied exclusive battery.
Charging the battery The base station works as the battery charging unit. Charge the rechargeable battery before starting to use the headphones. You can continuously use the headphones for about 10 hours after full battery charge. 1 Make sure that the headphones are turned off. You cannot charge the battery of the headphones when the headphones are turned on. Press POWER to turn the Power indicator off. 2 Put on the headphones on the base station so that their charging terminals contact firmly.
Basic operations • No sound is heard while Auto Tuning. It takes a few seconds to tune in. • Press AUTO SCAN when the sound does not come out properly. Listening to the sound from the base station The base station works as the FM transmitter and send sound to the headphones. Precaution Turn down the volume of the headphones with the VOL dial before turning on its power to avoid excessive volume. 1 Start playback on the AV equipment connected with the base station.
Basic operations Selecting a better reception channel When the playback sound is noisy, you can choose one of the other two channels to transmit signals on the base station. • The white noise may come out when switching the channel. Take off the headphones when switching the channel. 1 Slide the CHANNEL selector on the back side of the base station to select another channel. 2 Press AUTO SCAN on the headphones to tune in to the new channel. 3 Repeat Steps 1 and 2 to select the best channel.
Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. Symptom Cause/Remedy No sound comes out at all. • Turns on the power of the headphones. • Start playback on the AV equipment connected to the base station. • Check the connection between the base station and the AV equipment. • Turns up the volume of the headphones or the connected AV equipment to an appropriate level. • Fully charge the headphones’ battery.
Specifications General Specifications Modulation system: Stereo frequency modulation system Carrier frequency: 863.5 MHz (Channel 1) 864.0 MHz (Channel 2) 864.5 MHz (Channel 3) Usable area (distance to reach): Max. 100 m (using JVC measurement systems, under controlled ambient conditions) Frequency response: 25 Hz – 13,000 Hz Distortion: Less than 3% (at 1 kHz) Transmitter (J22321-001) Power requirements: DC 12 V (with the exclusive AC adaptor) Audio input terminals: 3.5 mm dia.
HAW600RF_B.indb 11 06.6.
HA-W600RF-B FM CORDLESS HEADPHONES © 2006 Victor Company of Japan, Limited HAW600RF_B.indb 2 Printed in China LNT0068-001A 06.6.