LCD Flat Television Users Guide For Model: LT-26WX84 Illustration of LT-26WX84 and RM-C13G Important Note: In the spaces below, enter the model and serial number of your television (located at the rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this guide. Keep this user’s guide in a convenient place for future reference. Keep the carton and original packaging for future use.
Important Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock. Do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• As an “ENERGY STAR®” partner, JVC has determined that this product or product model meets the “ENERGY STAR®” guidelines for energy efficiency. IMPORTANT SAFETY INSTRUCTIONS 1) 2) 3) 4) 5) 6) 7) 8) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
16) Avoid improper installation and never position the unit where good ventilation is impossible. When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance guidelines shown for safe operation. 200 mm 150 mm 200 mm 150 mm 50 mm 17) Cautions for installation — Do not tilt the TV towards the left or right, or towards the back.
Warnings Screen Burn-in By displaying fixed images for extended periods of time, can leave a subtle but permanent ghost image in your picture. This is referred to as "burn-in". To avoid this, mix your viewing pattern. Examples include, but are not limited to the following: • • • • • Stock-market report bars Shopping channel logos and pricing displays Video game patterns or scoreboards Bright station logos Internet web sites or other computer-style images.
Warnings How to move the cabinet Your fingers may become trapped under the TV, causing injuries. Hold the TV at the bottom in the middle, and do not allow the TV to tilt up or down. The TV may fall causing injuries. Hold the bottom of the stand with your hand and tilt the TV up or down. POWER Speaker panel note Do not press hard on the speaker area at the bottom front panel of the TV . Doing so can cause a dent to occur on the plastic grid.
Table of Contents Quick Setup . . . . . . . . . . . 8 Sound Adjust . . . . . . . . . 44 Unpacking your TV . . . . . . . . . . . . 8 TV Model . . . . . . . . . . . . . . . . 9 TV Remote Control . . . . . . . . . . . 10 Getting Started . . . . . . . . . . . . . 11 Using the Stand . . . . . . . . . . 11 The Remote Control . . . . . . . . . . 12 Connecting Your Devices . . . . . . . 13 Interactive Plug In Menu . . . . . . . . 20 Sound Settings . . . . . . . . . . . . Adjust Sound Settings . . . . . . . .
Quick Setup Unpacking your TV Thank you for your purchase of a JVC LCD Flat Television. Before you begin setting up your new television, please check to make sure you have all of the following items.
Quick Setup TV Model NOTE: Before you connect your television to another device, please refer to the proper diagrams for your specific TV and remote. These will help assist you in understanding how to connect your television to another device, as well as use the remote to set up your television.
Quick Setup TV Remote Control POWER TV CATV VCR DVD ASPECT MULTI SCREEN SPLIT INDEX FREEZE SWAP SELECT 1 2 3 4 5 6 7 8 100+ 0 INPUT 1 V1 INPUT 2 V2 INPUT 3 V3 9 RETURN+ INPUT 4 V4 DIGITAL-IN TV THEATER NATURAL VIDEO PRO CINEMA STATUS D-IN SLEEP TIMER DISPLAY SOUND LIGHT + MUTING C.C. C.C.
Quick Setup Getting Started Getting Started These quick setup pages will provide you, in three easy steps, with the basic information you need to begin using your new television right away. If you have questions, or for more detailed information on any of these steps, please consult other sections of this manual. Step 1 - Using the stand This TV comes with a Table Top Stand already attached. This stand can be used to adjust the direction of the TV screen 5º up, 10º down and 20º to the left or right.
Quick Setup Getting Started Step 2 – The Remote Control Before you can operate your remote control, you first need to install the batteries (included). Slide the cover on the back of the remote down towards the bottom of the remote control. Insert two batteries (included) carefully noting the “+” and “–” markings, placing the “–” end in the unit first. Slide the cover back into place. When you change the batteries, try to complete the task within three minutes.
Quick Setup Connections Step 3 - Connecting your devices Remove the terminal cover There are connection terminals behind the covers on the left and right in the back of the TV. Remove these two covers before connecting an antenna or other devices. The covers can be removed by removing the hook at the bottom and then pull out while slightly lifting. To replace the covers, first connect the hook at the top of the cover, and then insert the hook at the bottom.
Quick Setup Diagram #1 Connections INPUT 1 S-VIDEO VIDEO TV Rear Panel OVER VIDEO AUDIO INPUT 2 S-VIDEO VIDEO OVER VIDEO L AUDIO Cable or Antenna Output R VIDEO AUDIO Coaxial Cable MONITOR OUT S-VIDEO VIDEO VIDEO L AUDIO R IN OUT OR 75 (UHF/VHF ) Cable Box Note: • If you do not have a cable box, connect the cable wire from the wall outlet into the back of the TV.
Quick Setup Connections Notes: • Green, blue and red are the most common colors for DVD cables. Some models may vary colors. Please consult the user’s manual for your DVD player for more information. • Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete one set of connections (DVD or audio output) before starting the other to avoid accidentally switching the cables. • You may also connect the DVD player to Input 1.
Quick Setup Connections Connecting to a Camcorder You can connect a camcorder to you televison by using the input jacks located on the back of the television.
Quick Setup Connections Connecting to an External Amplifier INPUT 1 S-VIDE O VIDEO OVER TV Rear Panel VIDEO AUDIO INPUT 2 S-VIDE O VIDEO OVER VIDEO L AUDIO R VIDEO AUDIO Speaker MONIT OR OUT Speaker S-VIDE O VIDEO Amplifier VIDEO L AUDIO R 75 (UHF/V HF) 1) Connect a white cable from the LEFT AUDIO OUTPUT on the back of the TV to the LEFT AUDIO INPUT on the amplifier. 2) Connect a red cable from the RIGHT AUDIO OUTPUT on the back of the TV to the RIGHT AUDIO INPUT on the amplifier.
Quick Setup Connections Connecting to a Digital TV Receiver w/HDCP By inputting a high bandwidth digital content protection high definition picture source to the digital-in terminal of this television, high-definition pictures can be displayed on the screen in their digital form. (This terminal is for use in the future when high bandwidth digital content protection DTV decoders and DVD players and D-VHS are put on the market.
Quick Setup Connections Connecting to an AV Receiver using your television's V1 Smart Input By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture sources from many different devices, without having to change or use the other input connections on your TV. This allows you to free up the other input connections so you can connect more devices to your television.
Quick Setup Plug-In Menu Step 4 – The Interactive Plug In Menu When you turn your television on for the first time the interactive plug-in menu will appear. The plug-in menu helps you to get your TV ready to use by letting you set your preferences for: • The language in which you want the onscreen menus to appear. • Setting the TV’s clock to the correct time so your timer functions will work properly. You can choose “AUTO” or “MANUAL” for setting the clock.
Quick Setup Plug-In Menu Auto Clock Set Before you use any of your TV’s timer functions, you must first set the clock. You may precisely set your clock using the XDS time signal broadcast by most public broadcasting stations. If you do not have this in your area, you will have to set the clock manually. See manual clock set below. To set the clock using the XDS signal: SET CLOCK MODE TIME ZONE D.S.T.
Quick Setup Plug-In Menu Auto Tuner Setup In auto tuner setup, the TV automatically scans through all available channels, memorizing the active ones and skipping over blank ones or channels with weak signals. This means when you scan (using the CHANNEL +/– buttons) you will receive only clear, active channels.
Remote Programming Setting the CATV, VCR and DVD Codes You can program your remote to operate your cable box, satellite receiver, VCR or DVD player by using the instructions and codes listed below. If the equipment does not respond to any of the codes listed below or to the code search function, use the remote control supplied by the manufacturer. Cable Box or Satellite Codes The remote control is programmed with cable box and satellite codes for power on/off, channel up/down, and 10 key operation.
Remote Programming VCR Codes The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward, rewind, pause, record, channel up/down operation. 1) Find the VCR brand from the list of codes shown below. 2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”. 3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10 key pad. 4) Release the DISPLAY button, and confirm the operation of the VCR.
Remote Programming DVD Codes The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward, rewind, previous/next chapter, tray open/close, and still/pause operation. 1) Find the DVD player brand from the list of codes shown below. 2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”. 3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10 key pad.
Remote Programming Search Codes Cable/Satellite Search Codes Function 1) Slide the first 2-Way Mode Selector switch to CATV. 2) Press and hold down the POWER button, then press the RETURN+/TV button for more than three seconds. 3) Release the RETURN+/TV button, then release the POWER button. 4) Press the POWER button on the remote, and see if the cable or satellite box responds. 5) If there was a response, press RETURN+/TV. The codes are now set. If there was no response, repeat Step 4.
Onscreen Menus Using the Guide Certain symbols are used throughout this guide to help you learn about the features of your new television. The ones you will see most frequently are: π† Up and Down arrows mean press the CH+ or CH– buttons.
Onscreen Menus The Onscreen Menu System Your television comes with JVC’s onscreen menu system. The onscreen menus let you make adjustments to your television’s operation simply and quickly. Examples of the onscreen menus are shown on the next page. Detailed explanations on using each menu follow later in this guide. For information about the interactive plug-in Menu, see pages 20 - 22. The Onscreen Menu System To open the onscreen menu system, press the MENU button on the remote control.
Onscreen Menus Press the MENU button INITIAL SETUP INITIAL SETUP PREVIOUS AUTO TUNER SETUP CHANNEL SUMMARY V-CHIP SET LOCK CODE AUTO DEMO PREVIOUS LANGUAGE MENU Notes: STANDARD 00 00 00 00 00 ENERGY SAVER MODE NEXT PAGE SELECT OPERATE MENU EXIT PICTURE ADJUST 01 PICTURE ADJUST PREVIOUS STANDARD COLOR TEMPERATURE DIG.
Initial Setup Auto Tuner Setup The auto tuner setup function is described on page 22 as the interactive plug-in menu. If you need to run the auto tuner setup again, follow the steps below. Press the MENU button π† To AUTO TUNER SETUP √® √® To operate To choose CABLE or AIR AUTO TUNER SETUP CABLE TUNER MODE Press the OK button to start PRESS SELECT OK TO START OPERATE MENU EXIT Programming will take approximately 1 to 2 minutes.
Initial Setup Channel Guard Message When a viewer attempts to watch a guarded channel, the following message appears: To watch a channel that you have locked, enter the Lock Code using the 10 key pad. If the wrong code is entered, the message “INVALID LOCK CODE!” will flash on the screen. The channel cannot be accessed until the correct code is entered. THIS CHANNEL IS LOCKED BY CHANNEL GUARD. PLEASE ENTER LOCK CODE BY 10 KEY PAD TO UNLOCK IT. NO.
Initial Setup Unrated Programs Unrated programming refers to any programming which does not contain a rating signal. Programming on television stations which do not broadcast rating signals will be placed in the “Unrated Programming” category.
Initial Setup US V-Chip Ratings U.S. PARENTAL RATING SYSTEMS Programs with the following ratings are appropriate for children. q TV Y is Appropriate for All Children Programs are created for very young viewers and should be suitable for all ages, including children ages 2 - 6. q TV Y7 is for Older Children Most parents would find such programs suitable for children 7 and above. These programs may contain some mild fantasy violence or comedic violence, which children should be able to discern from reality.
Initial Setup Setting US V-Chip Ratings Press the MENU button π† √® To V-CHIP To operate (lock icon V-CHIP appears) Press ZERO to access the V-Chip menu √® π† √® OFF V-CHIP To turn V-Chip ON or OFF To move to SET US TV RATINGS To operate SET US TV RATINGS SET MOVIE RATINGS SET CANADIAN RATINGS ENG SET CANADIAN RATINGS FRE UNRATED VIEW SELECT OPERATE EXIT MENU Directions to set US V-Chip Ratings Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.
Initial Setup Movies Ratings q NR – Not Rated This is a film which has no rating. In many cases these films were imported from countries which do not use the MPAA ratings system. Other NR films may be from amateur producers who didn’t intend to have their film widely released. NR (Not Rated) Programming may contain all types of programming including children’s programming, foreign programs, or adult material.
Initial Setup Canadian V-Chip Ratings q q q q q q q E – Exempt Exempt programming includes: news, sports, documentaries and other information programming, talk shows, music videos, and variety programming. C – Programming Intended for Children Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or unrealistic in nature.
Initial Setup Set Lock Code Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes preset with a lock code of “0000”. You may change the code to any four-digit number you wish. To change the lock code, follow the steps below.
Initial Setup Language The language function is described on page 20 as the interactive plug-in menu. If you need to choose the language again, follow the steps below. Press the Menu button π† √® To LANGUAGE To choose a language: ENG. (English), FRAN. (French) or ESP. (Spanish) Press the MENU button when finished Closed Caption INITIAL SETUP PREVIOUS LANGUAGE ENG. FRAN. ESP.
Initial Setup XDS ID XDS ID Display provides a channel’s call letters, the network’s name, and even a program name. The XDS ID information is provided by the broadcaster. Press the MENU button π† √® To XDS ID To turn ON or OFF Press the MENU button when finished INITIAL SETUP PREVIOUS LANGUAGE ENG. FRAN. ESP.
Initial Setup V1 Smart Input This feature is used if you have connected an AV Receiver to your television. By turning this feature on, your television can automatically detect the signal source from your components that are connected to your AV Receiver. Press the MENU button To V1 SMART INPUT To turn ON or OFF π† √® Press the MENU button when finished Notes: • If you do not have an AV Receiver connected to your television, turn this feature OFF.
Initial Setup Video-1 Monitor Out This function allows you to set whether the signal, which comes from VIDEO-1 input terminal, should be output from MONITOR OUT terminal. If you select it from MONITOR OUT, set it to "ON".
Picture Adjust Picture Settings These settings allow you to change and adjust the way the picture appears on your television. TINT Tint allows you to adjust the levels of red and green in your TV picture. COLOR The color function lets you make all the colors in the TV picture appear either more vivid or subtle. PICTURE Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker or brighter picture overall.
Picture Adjust Color Temperature You can decide how strong or dull the colors appear on the TV screen. Press the MENU button π† √® To COLOR TEMPERATURE To enter COLOR TEMPERATURE √® LOW HIGH PICTURE ADJUST PREVIOUS STANDARD COLOR TEMPERATURE DIG.
Sound Adjust Sound Settings These settings allow you to change and adjust the sound on your television. BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with the bass adjustment. TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio. BALANCE – Adjust the level of sound between the TV’s left and right speakers with the balance setting.
Clock/Timers Set Clock The set clock function is described on page 21 as the interactive plug-in menu. You can choose to set the clock automatically, or manually. If you need to set the clock again, follow the steps below. Press the MENU button π† To SET CLOCK √® To operate When you set the clock automatically, choose AUTO by pressing the π† To TIME ZONE √® To select your time zone ATLANTIC π† √® SET CLOCK EASTERN HAWAII √ or ® arrows. CENTRAL ALASKA MOUNTAIN AUTO MODE PACIFIC To D.S.T.
Clock/Timers On/Off Timer The on/off timer lets you program your television to turn itself on or off. You can use it as an alarm to wake up, to help you remember important programs, or as a decoy when you’re not home. Press the MENU button π† To ON/OFF TIMER √® √® To operate (begins with ON TIME) To set the hour (AM/PM) you want the TV to turn on † To move to minutes √® To set the minutes † To accept ON TIME and move to OFF TIME (the time the TV will turn off).
Button Functions Multi Screen Function Your television has two kinds of screen: SPLIT (2 channels), and INDEX (12 channels). Note: After you press any multiscreen button, if you press the menu button, only the picture adjust screen will appear. Split Activate the split-screen option by pressing SPLIT on the remote control. Two channels (or input) will now appear onscreen. The channel (or input) you were watching before pressing SPLIT will appear on the left, the new channel will appear on the right.
Button Functions Index This allows you to quickly look at up to 12 channels at a time so that you can decide which one to watch. 1 2 3 4 5 6 7 8 9 10 11 12 Notes: • Only RF input signal will be displayed. • You can watch the channel added in channel summary. See page 30. Freeze Pressing the FREEZE button causes the screen to change to the split-screen display with the still picture displayed on the right. In order to return to the normal display, press the FREEZE button once again.
Button Functions Power Turns the TV on or off. Press the POWER button Number Buttons - 10Key Pad Use the number buttons on the remote control to move directly to a specific channel. For example, to move to channel 7: 0 (Zero) 7 (Seven) 100+ Button Use the 100+ button to directly access channels above channel 99. For example, to move to channel 124, press 100+, 2 (Two), 4 (Four).
Button Functions Return +/TV The return+/TV button has three functions: Return - Returns to the channel viewed just before the channel currently onscreen. Return+ - Lets you program a specific channel to return to while scanning through the channels using the CH+ and CH– buttons. TV - Returns to the TV mode. RETURN+/TV and hold for three seconds RETURN CHANNEL PROGRAMMED! The channel currently active has been programmed as your return+ channel. Now scan through the channels using the CHANNEL+/– buttons.
Button Functions Video Status The Video status button gives you a choice of four TV picture display settings, including a display of your own preferences. Standard - Resets the picture display to the factory settings. VIDEO STATUS STANDARD Dynamic - Gives a vivid picture with better contrast when viewing in a brightly lit room. DYNAMIC THEATER GAME Theater - Gives a rich, film-like look to video when viewing in a dimly lit room. Game - Used for when you are playing video games connected to your TV.
Button Functions Sleep Timer The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals of 15 minutes, for a total time of up to 180 minutes. Press the SLEEP TIMER button 0 15 30 45 60 75 90 105 120 135 150 165 180 Sleep Timer Message 20 seconds before the automatic shutoff, this message will appear: GOOD NIGHT!! PUSH SLEEP TIMER BUTTON TO EXTEND You then have 20 seconds to press the SLEEP TIMER button to delay the shut off for another 15 minutes.
Button Functions Aspect This feature will help you adjust the picture you are watching to give you the best possible picture quality. Aspect Ratios PANORAMA - With this ratio a normal 4:3 aspect picture is stretched to fit the dimensions of the 16:9 aspect screen. REGULAR - The regular ratio is used when you want to watch a 4:3 broadcast or recorded program without modifying the original picture to fit the dimensions of your 16:9 screen.
Button Functions Aspect Ratios (Continued) Press the ASPECT button • By pressing the ASPECT button, you can change the size. When you change the aspect ratios, it is different from their broadcast or recorded program. NTSC, 480i, 480p, HDCP 480p ASPECT PANORAMA CINEMA FULL REGULAR HD, HDCP 1080i 720P, HDCP 720p ASPECT HD PANORAMA CINEMA ZOOM FULL ASPECT FULL Notes: • You can also choose the size by pressing the π† buttons.
Button Functions TV/CATV Slide Switch Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to operate the television’s built-in tuner. Move the switch to CATV to operate a cable box. Note: • See page 23 for information on programming your remote for cable box operation. VCR/DVD Slide Switch You can control a VCR or DVD player with the buttons on the lower part of the remote control. Move the slide switch to VCR or DVD to operate.
Troubleshooting PROBLEMS CHECK There is no power • See if the power cord became unplugged. • Check for a blown fuse or circuit breaker or a power outage. There is no picture or sound • The antenna could be disconnected. • The input mode could be set improperly. See page 49. • The tuner (Auto Tuner Setup) could be set improperly. See page 30. • The TV station may be having difficulties. Check to see if other stations are working.
Warranty JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period shown below. (“The Warranty Period”) PARTS 1 YEAR LABOR 1 YEAR This limited warranty is valid only in the fifty (50) United States, The District of Columbia and Commonwealth of Puerto Rico.
Warranty THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
Authorized Service Centers QUALITY SERVICE HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE: 1 (800) 537-5722 http://www.jvc.com Dear Customer, In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the unit. In the event that repairs are necessary, call our Customer Relations Department at 1-800-537-5722 or visit our website at www.JVC.com Remember to retain your Bill of Sale for Warranty Service.
Specifications Model LT-26WX84 Type LCD Flat Television Reception Format NTSC, BTSC System (Multi-Channel Sound) HDTV digital broadcast ready Reception Range VHF 2 to 13, UHF 14 to 69 Sub, Mid, Super, Hyper and Ultra bands (180 channel frequency synthesizer system) Power Source AC 120V, 60 Hz Power Consumption 155W Screen Size 26 inch / 66 cm measured diagonally, 16:9 ratio Speakers 6.
Manuel d’instructions du téléviseur à écran plat et affichage à cristaux liquides Pour Le Modèle: LT-26WX84 Illustration du modèle LT-26WX84 and RM-C13G Information importante pour l’utilisateur : Veillez inscrire dans l’espace ci-dessous le numéro de série de votre téléviseur (situé à l’arrière du téléviseur). Agrafez votre reçu ou votre facture à la couverture, à l’intérieur de ce guide. Rangez ce manuel dans un lieu où vous pourrez le retrouver rapidement pour vous y référer.
IMPORTANTES PRECAUTIONS DE SECURITE ATTENTION RISQUE D’ÉLECTROCUTION NE PAS OUVRIR ATTENTION : Pour diminuer les risques d’électrocution Ne pas retirer le capot (ou le panneau arrière). Aucune pièce à l’intérieur n’est réparable par l’utilisateur. Adressez-vous à un réparateur qualifié pour la maintenance.
• Comme société « ENERGY STAR® » , JVC a déterminé que ce produit ou modèle de produit est conforme aux directives « ENERGY STAR® » pour le rendement énergétique. IMPORTANTES CONSIGNES DE SÉCURITÉ 1) 2) 3) 4) 5) 6) 7) 8) Lisez ces consignes. Gardez ces consignes. Conformez-vous à tous les avertissements. Suivez toutes les consignes. N’utilisez pas cet appareil près de l’eau. Nettoyez uniquement à l’aide d’un chiffon sec. Ne bloquez aucune prise d’air.
16) Évitez une installation inappropriée et ne positionnez jamais là où il est impossible d’assurer une bonne ventilation. Lors de l’installation de ce téléviseur, conformez-vous aux recommandations de distance entre l’appareil et le mur ainsi qu’à l’intérieur d’un meuble ou d’un endroit restreint. Observez les lignes directrices de distance minimum montrées ci-après pour un fonctionnement sûr.
Précautions Burn-in de l’écran L’affichage d’images fixes pendant des périodes prolongées peut laisser une image fantôme subtile mais permanente sur votre écran. Ce phénomène est désigné sous le nom de « burn-in ». Pour éviter ceci, mélangez les programmes que vous regardez.
Précautions Déplacement du téléviseur Vous pouvez vous prendre les doigts sous le téléviseur et être blessé. Tenez le téléviseur au centre de la partie inférieure et évitez d’incliner le téléviseur vers le haut ou vers le bas. Le téléviseur peut tomber et causer des blessures. Tenez le bas du support avec votre main et inclinez le téléviseur vers le haut ou vers le bas. POWER Remarque sur le panneau des haut-parleurs.
Tables des matières Configuration rapide . . . . . 8 Réglages du son . . . . . . . . 44 Déballage de votre téléviseur . . . . . . . . 8 Modèle de téléviseur . . . . . . . . . . 9 Télécommande de téléviseur . . . . . . 10 Pour débuter . . . . . . . . . . . . . . . 11 Using the Stand . . . . . . . . . . . . 11 La télécommande . . . . . . . . . . 12 Raccordement de vos appareils . . . . 13 Plug-in menu interactif . . . . . . . . 20 Réglages du son . . . . . . . . . . . . . Ajustement des réglages du son . .
Configuration rapide Déballage de votre téléviseur Merci d’avoir acheté un téléviseur à écran plat et affichage à cristaux liquides JVC. Avant de commencer l’installation de votre nouveau téléviseur, assurez-vous d’avoir toutes les pièces suivantes.
Configuration rapide Modèle de téléviseur REMARQUE : Avant de raccorder votre téléviseur à un autre appareil, veuillez vous reporter aux schémas appropriés pour votre téléviseur et votre télécommande précis. Ceci vous aidera à comprendre la manière de raccorder votre téléviseur à un autre appareil, ainsi qu’à utiliser la télécommande pour configurer votre téléviseur.
Configuration rapide Télécommande de téléviseur POWER TV CATV VCR DVD ASPECT MULTI SCREEN SPLIT INDEX FREEZE SWAP SELECT 1 2 3 4 5 6 7 8 100+ 0 INPUT 1 V1 INPUT 2 V2 INPUT 3 V3 9 RETURN+ INPUT 4 V4 DIGITAL-IN TV THEATER NATURAL VIDEO PRO CINEMA STATUS D-IN SLEEP TIMER DISPLAY SOUND LIGHT + MUTING C.C. C.C.
Configuration rapide Pour débuter Pour débuter Ces pages de configuration rapide vous donneront, en trois étapes faciles, les informations de base dont vous avez besoin pour commencer à utiliser immédiatement votre nouveau téléviseur. Si vous avez des questions, ou pour obtenir des informations plus détaillées sur l’une quelconque de ces étapes, veuillez consulter d’autres sections de ce guide. Étape 1 – Utilisation du support Ce téléviseur est offert avec un support de table déjà fixé.
Configuration rapide Pour débuter Étape 2 - La télécommande Avant de pouvoir utiliser votre télécommande, vous devez d’abord poser les piles (fournies). Faites glisser le couvercle à l’arrière de la télécommande vers le bas de la télécommande. Insérez deux piles en notant soigneusement les marquages « + » et « – » et en plaçant l’extrémité « – » dans l’appareil en premier. Remettez le couvercle en place. Lorsque vous changez les piles, tentez de le faire en moins de trois minutes.
Configuration rapide Connexions Étape 3 – Raccordement de vos dispositifs Retirez le couvercle de bornes Il y a des bornes de connexion derrière les couvercles à gauche et à droite à l’arrière du téléviseur. Retirez ces deux couvercles avant de raccorder une antenne ou d’autres dispositifs. Pour déposer les couvercles, retirez le crochet dans la partie inférieure, puis tirez vers l’extérieur tout en levant légèrement.
Configuration rapide Connexions Schéma no. 1 INPUT 1 S-VIDEO Panneau arrière du téléviseur VIDEO OVER VIDEO AUDIO INPUT 2 S-VIDEO VIDEO OVER VIDEO L AUDIO Câble ou sortie antenne R VIDEO AUDIO Câble coaxiaux MONITOR OUT S-VIDEO VIDEO VIDEO L AUDIO R IN OUT OU 75 (UHF/VHF ) Boîte de câble Remarque : • Si vous n’avez pas de boîte de câble, raccordez le fil de câble provenant de la prise murale à l’arrière du téléviseur. Schéma no.
Configuration rapide Connexions Remarques : • Le vert, le bleu et le rouge sont les couleurs les plus répandues des câbles de DVD. Les couleurs peuvent varier sur certains modèles. Pour de plus amples renseignements, prière de consulter le manuel de l’utilisateur de votre lecteur de DVD. • Veillez à ne pas confondre le câble de DVD rouge avec le câble audio rouge.
Configuration rapide Connexions Connexion à un caméscope Vous pouvez raccorder un caméscope à votre téléviseur en utilisant les jacks d’entrée situés à l’arrière du téléviseur.
Configuration rapide Connexions Connexion à un amplificateur externe INPUT 1 S-VIDE VIDEO O OVER Panneau arrière du téléviseur VIDEO AUDIO INPUT 2 S-VIDE VIDEO O OVER VIDEO L AUDIO R VIDEO AUDIO Haut-parleur droit Haut-parleur gauche MONIT OR OUT S-VIDE O Amplificateur VIDEO VIDEO L AUDIO R 75 (UHF/V HF) 1) Raccordez un câble blanc depuis la SORTIE AUDIO GAUCHE à l’arrière du téléviseur dans l’ENTRÉE AUDIO GAUCHE de l’amplificateur.
Configuration rapide Connexions Connexion à un récepteur TV numérique avec HDCP En introduisant une source d’image Haute définition Protection du contenu numérique à bande passante élevée à la borne d’entrée numérique de ce téléviseur, des images à haute définition peuvent être affichées à l’écran sous leur forme numérique.
Configuration rapide Connexions Raccordement à un récepteur AV à l’aide de l’entrée V1 Smart Input de votre téléviseur En raccordant votre récepteur AV à l’entrée V1 Smart Input de votre téléviseur, vous pouvez regarder des sources d’image depuis un grand nombre de dispositifs différents, sans avoir à changer ni à utiliser les autres connexions d’entrée de votre téléviseur. Ceci vous permet de libérer les autres connexions d’entrée pour pouvoir ainsi raccorder plus de dispositifs à votre téléviseur.
Configuration rapide Plug-in menu Étape 4 - Le plug-in menu interactif Le plug-in menu interactif apparaît lorsque vous mettez votre téléviseur en marche pour la première fois. Ce menu vous aide à configurer votre téléviseur pour usage en vous permettant de définir vos préférences concernant : • La langue dans laquelle vous voulez que les menus à l’écran apparaissent. • Le réglage de l’horloge du téléviseur à la bonne heure afin que vos fonctions de minuterie fonctionnent adéquatement. Choix d’« AUTO.
Configuration rapide Plug-in menu Régler horloge automatique Avant d’utiliser l’une quelconque des fonctions de minuterie de votre téléviseur, vous devez d’abord régler l’horloge. Vous pouvez régler votre horloge avec précision en utilisant le signal horaire XDS transmis par la plupart des postes de public broadcasting. S’il n’y a pas de poste PBS dans votre région, vous devrez régler l’horloge manuellement. Reportez-vous à la section réglage manuel de l’horloge ci-après.
Configuration rapide Plug-in menu Régler auto tuner En mode auto tuner setup, le téléviseur balaye automatiquement tous les canaux disponibles, mettant en mémoire les canaux actifs et sautant les canaux vides ou les canaux dont le signal est faible. Ceci signifie que, durant le balayage (à l’aide des boutons CHANNEL +/–), vous ne recevrez que les canaux clairs et actifs. √® RÉGLER AUTO TUNER † Pour choisir CÂBLE ou ANT. (ou SAUTER L’ÉTAPE lorsque vous sautez RÉGLER AUTO TUNER).
Programmation de la télécommande Réglage des codes CATV, magnétoscope et lecteur de DVD Vous pouvez programmer votre télécommande de manière à actionner votre boîte de câble, récepteur satellite, magnétoscope ou lecteur de DVD en vous reportant aux instructions et aux codes répertoriés ci-dessous. Si l’appareil ne répond à aucun des codes répertoriés ci-après ou à la fonction de recherche de codes, utilisez la télécommande fournie par le fabricant.
Programmation de la télécommande Codes du magnétoscope La télécommande est programmée avec les codes de magnétoscope pour la mise sous et hors tension, la lecture, l’arrêt, l’avance rapide, le rembobinage, la pause, l’enregistrement et le balayage de canaux vers le haut et vers le bas. 1) Repérez la marque du magnétoscope dans la liste de codes indiqués ci-dessous.
Programmation de la télécommande Codes DVD La télécommande est programmée avec les codes DVD pour la mise sous et hors tension, la lecture, l’arrêt, l’avance rapide, le rembobinage, chapitre précédent, chapitre suivant, l’ouverture et la fermeture du plateau, l’image fixe et la pause. 1) Repérez la marque du lecteur de DVD dans la liste de codes indiqués ci-dessous.
Programmation de la télécommande Codes de recherche Fonction de codes de recherche pour boîte de câble ou antenne parabolique 1) Faites glisser le premier interrupteur sélecteur à deux voies sur la position CATV. 2) Enfoncez et tenez le bouton POWER, puis appuyez sur le bouton RETURN+/TV pendant plus de trois secondes. 3) Relâchez le bouton RETURN+/TV, puis relâchez le bouton POWER. 4) Appuyez sur le bouton POWER de la télécommande et vérifiez que la boîte de câble ou de l’antenne parabolique répond.
Menus à l’écran Utilisation du guide Certains symboles sont utilisés tout au long de ce guide pour vous aider à apprendre les fonctions de votre nouveau téléviseur. Ceux que vous verrez le plus souvent sont les suivants : π† Les flèches montante et descendante signifient appuyer sur les boutons CH+ ou CH–.
Menus à l’écran Système de menus à l’écran Votre téléviseur est équipé d’un système de menus à l’écran JVC. Ces menus vous permettent de régler facilement et rapidement votre téléviseur. Des exemples de menus à l’écran sont donnés à la page suivante. Des explications détaillées portant sur l’utilisation de chaque menu sont données par la suite dans ce guide. Reportez-vous aux pages 20 à 22 pour obtenir des informations sur le Plug In Menu interactif.
Menus à l’écran Appuyez sur le bouton MENU CONFIG. INITIALE CONFIG. INITIALE PRÉCÉDENTE RÉGLER AUTO TUNER SOMMAIRE CANAUX V-CHIP PRÉCÉDENTE ENG. FRAN. ESP.
Configuration initiale Réglage de l’auto tuner La fonction de réglage de l’auto tuner est décrite à la page 22 en tant que plug-in menu interactif. Si vous voulez accéder à nouveau à cette fonction, suivez les étapes ci-après. Appuyez sur le bouton MENU π† Vers RÉGLER AUTO TUNER √® √® Pour activer Pour choisir CÂBLE ou ANT.
Configuration initiale Message d’un canal réservé Quand un spectateur essaie de regarder un canal réservé, ce message apparaît : Pour regarder un canal que vous avez verrouillé, entrez le code de verrouillage en utilisant le pavé numérique à 10 touches. Si le mauvais code est entré, le message « CODE D’ACCÈS INVALIDE » clignote à l’écran. Le canal est inaccessible jusqu’à ce que le code correct soit introduit.
Configuration initiale Programmes non cotés La programmation non cotée désigne tout programme qui ne contient pas de signal de cote. Les programmes des postes de télévision qui ne transmettent pas les signaux de cote seront dans la catégorie « programmation non cotée ».
Configuration initiale Cotes américaines de Puce V SYSTÈMES AMÉRICAINS DE COTES PARENTALES Les programmes possédant les cotes suivantes sont appropriés pour les enfants. q TV Y est approprié pour tous les enfants Ces programmes sont réalisés pour de très jeunes spectateurs, et ils devraient convenir à tous les âges, y compris les enfants âgés de 2 à 6 ans. q TV Y7 est destiné aux enfants plus âgés La plupart des parents devraient trouver ces programmes convenables pour les enfants âgés de 7 ans et plus.
Configuration initiale Configuration des cotes américaines de Puce V Appuyez sur le bouton MENU π† √® √® π† √® Vers V-CHIP Pour exécuter (l’icône de verrouillage V-CHIP OFF V-CHIP apparaît) FIXER COTES TÉLÉVISEUR FIXER COTES FILM Appuyez sur ZÉRO pour accéder au menu puce V SYST CLASSIFICAT CAN ANG Pour ON (activer) ou OFF (inactiver) la puce V Pour passer à FIXER COTES TÉLÉVISEUR Pour exécuter NONCOTÉ SYST CLASSIFICAT CAN FRE CHOIX VISUALISER OPÈRE MENU SORTIR Instructions pour configure
Configuration Initiale Cotes de films NR – Non coté Il s’agit de film non coté. Ces films sont souvent importés de pays qui n’utilisent pas le système de cotes MPAA. D’autres films NR peuvent être l’oeuvre de réalisateurs amateurs qui n’avaient pas l’intention de diffuser leurs films dans le grand public. La programmation NR peut contenir tous les types de programmation, y compris des programmes pour les enfants, des programmes étrangers et du matériel adulte.
Configuration Initiale Cotes canadiennes de Puce V q q q q q q E - Exempté. Les programmes exempts comprennent : les informations, les émissions sportives, les documentaires et autres programmes d’information, les débats, les vidéos de musique, et les programmes de variétés. G – Général. Directives de violence : il n’y aura aucune scène réaliste de violence. Les descriptions de comportements agressifs seront rares et limitées à des représentations de nature clairement fictive, comique ou irréaliste.
Configuration initiale Réglage du code de verrouillage Les réglages de canal réservé et de Puce V sont protégés par un code de verrouillage à quatre chiffres. Votre téléviseur est livré préréglé avec un code de verrouillage de 0000. Vous pouvez changer le code de verrouillage par n’importe quel nombre de quatre chiffres.
Configuration initiale Langue La fonction Langue est décrite à la page 20 du plug-in menu interactif. Si vous devez choisir à nouveau la langue, suivez les étapes ci-après. Appuyez sur le bouton MENU π† √® Vers LANGUE Pour choisir une langue : ENG. (anglais), FRAN. (français) ou ESP. (espagnol). Appuyez sur le bouton MENU lorsque vous avez terminé Sous-titres CONFIG. INITIALE PRÉCÉDENTE ENG. FRAN. ESP.
Configuration initiale XDS ID L’affichage XDS ID procure les lettres d’identification du canal, le nom du réseau et même un nom de programme. Les informations XDS ID sont fournies par le télédiffuseur. Appuyez sur le bouton MENU π† √® Vers XDS ID Pour ON (activer) ou OFF (inactiver) Appuyez sur le bouton MENU lorsque vous avez terminé CONFIG. INITIALE PRÉCÉDENTE ENG. FRAN. ESP.
Configuration initiale V1 Entrèe intelligente Cette fonction s’emploie si vous avez raccordé un récepteur AV à votre téléviseur. En activant cette fonction, l’entrée VIDEO-1 de votre téléviseur peut détecter automatiquement la source de signal depuis vos composants raccordés à votre récepteur AV. Appuyez sur le bouton MENU Vers V1 ENTRÈE INTELLIGENTE Pour ON (activer) ou OFF (inactiver) π† √® Appuyez sur le bouton MENU lorsque vous avez terminé CONFIG.
Configuration initiale Sortie Moniteur V1 Cette fonction vous permet de décider si le signal, qui provient de la borne d’entrée VIDEO-1, doit sortir de la borne MONITOR OUT. Si vous faites cette sélection depuis MONITOR OUT, mettez à la position « ON ». Appuyez sur le bouton MENU π† Vers SORTIE MONITEUR V1 √® Pour choisir ON or OFF CONFIG.
Réglage de l’image Réglages de l’image Ces réglages vous permettent de modifier et d’ajuster la façon dont l’image apparaît sur votre téléviseur. TEINTE Ceci vous permet d’ajuster les niveaux de rouge et de vert dans l’image de votre téléviseur. COULEUR La fonction de couleur vous permet de rendre toutes les couleurs de l’image plus vives ou plus subtiles.
Réglages de l’image Température couleur Grace à température des couleurs, vous pouvez décider l’intensité (élevée ou faible) des couleurs apparaissant sur l’écran de télévision. Appuyez sur le bouton MENU π† √® Vers TEMP. COULEUR Pour exécuter TEMP. COULEUR √® BASSE HAUTE AJUSTAR IMAGEN PRÉCÉDENTE STANDARD BASSE TEMP.
Réglages du son Réglages du son Ces réglages vous permettent de modifier et d’ajuster le son de votre téléviseur. BASSE – La fonction de réglage du niveau de basse vous permet d’augmenter ou de diminuer le niveau des sons à basse fréquence dans l’audio de votre téléviseur. AIGU – La fonction de réglage du niveau d’aigu vous permet d’augmenter ou de diminuer le niveau des sons à haute fréquence dans l’audio de votre téléviseur.
Horloge/minuteries Réglage de l’horloge La fonction de réglage de l’horloge est décrite à la page 21 en tant que plug-in menu interactif. Vous pouvez choisir de régler l’horloge automatiquement ou manuellement. Si vous avez besoin de régler l’horloge à nouveau, suivez les étapes ci-après. Appuyez sur le bouton MENU π† Vers RÉGLER HORLOGE √® Pour exécuter Lorsque vous réglez l’horloge automatiquement, choisissez AUTO. en appuyant sur les touches √ ou ®.
Minuterie/horloges Minuterie on/off La fonction minuterie on/off vous permet de programmer votre téléviseur pour qu’il s’allume ou s’éteigne de lui-même. Vous pouvez utiliser cette fonction comme alarme pour vous réveiller le matin, pour vous rappeler l’heure d’un programme important ou comme dispositif de sécurité pour donner l’impression qu’il y a quelqu’un chez vous quand vous êtes absent.
Fonctions des boutons Fonction multi screen Votre téléviseur possède deux types d’écran : SPLIT (2 canaux), et INDEX (12 canaux). Remarque : Après avoir appuyé sur tout bouton multiscreen, si vous appuyez sur le bouton de MENU, seul l’écran de réglage d’image apparaîtra. Split Activez l’option image-sur-image en appuyant sur le bouton SPLIT de la télécommande. Deux canaux (ou entrées) apparaissent maintenant sur l’écran.
Fonctions des boutons Index Ce bouton vous permet de regarder rapidement un nombre allant jusqu’à 12 canaux à la fois pour décider celui que vous voulez regarder. 1 2 3 4 5 6 7 8 9 10 11 12 Remarques : • Seul le signal d’entrée RF est affiché. • Vous pouvez regarder le canal ajouté dans le sommaire canaux. Reportez-vous à la page 30. Freeze Appuyez sur le bouton FREEZE pour changer l’affichage d’image-sur-image, à la droite de l’écran, par l’affichage d’une image fixe.
Fonctions des boutons Power Allume ou éteint le téléviseur. Appuyez sur le bouton POWER Boutons de numéro – Clavier numérique à 10 touches Utilisez les touches numériques de la télécommande pour passer directement à un canal précis. Par exemple, pour passer au canal 7 : 0 (Zéro) 7 (Sept) 100+ (Bouton 100+) Appuyez sur le bouton 100+ pour accéder directement aux canaux au-dessus de 99. Par exemple, pour passer au canal 124, appuyez sur 100+, 2 (deux), 4 (quatre).
Fonctions des boutons Return +/TV Le bouton return+/TV a trois fonctions : Return - Retour au canal regardé immédiatement avant le canal maintenant à l’écran. Return+ - Vous permet de programmer un canal précis auquel revenir après le balayage à travers les canaux à l’aide des boutons CH+ et CH–. TV - Ramène au mode TV. RETURN+/TV et tenez pendant trois secondes. RETOUR Â CANAL PROGRAMMÉ Le canal actuellement actif a été programmé comme votre canal return+.
Fonctions des boutons Video Status (Statut vidéo) Le bouton video status vous offre un choix de quatre réglages d’affichage d’image, y compris un affichage de vos propres préférences. STANDARD - Rétablit l’affichage de l’image aux réglages d’usine. DYNAMIQUE - Donne une image vive avec un meilleur contraste lorsque vous regardez la télévision dans une pièce très éclairée. CINÉMA - Donne à la vidéo un aspect riche, similaire au film, lorsque vous la regardez dans une pièce faiblement éclairée.
Fonctions des boutons Sleep Timer (Minuterie de sommeil) Cette minuterie met le téléviseur hors tension à votre place en cas d’assoupissement. Vous pouvez programmer cette fonction avec des intervalles de 15 minutes, pour un temps total allant jusqu’à 180 minutes. Appuyez sur le bouton SLEEP TIMER 0 15 30 45 60 75 90 105 120 135 150 165 180 Message de la minuterie de sommeil 20 secondes avant l’extinction automatique, ce message apparaîtra : BONNE NUIT!! PRESSER LE BOUTON MINUT.
Fonctions des boutons Aspect (Format d’image) Cette fonction vous aidera à ajuster l’image que vous regardez pour obtenir la meilleure qualité d’image possible. Formats d’image PANORAMA - Avec ce format, une image normale de format 4:3 est étirée pour correspondre à un écran de format 16:9. CINÉMA - Ce format « agrandit » le centre de l’image de format 4:3, le gonflant pour le faire correspondre à un écran de format 16:9.
Fonctions des boutons Formats d’image (suite) Appuyez sur le bouton ASPECT • Vous pouvez modifier le format en appuyant sur le bouton ASPECT Lorsque vous changez le format d’image, il est différent de sa diffusion ou du programme enregistré. NTSC, 480i, 480p, HDCP 480p ASPECT PANORAMA CINÉMA PLEIN RÉGULIER HD, HDCP 1080i 720P, HDCP 720p ASPECT HD PANORAMA CINÉMA ZOOM PLEIN ASPECT PLEIN Remarques : • Vous pouvez également modifier le format en appuyant sur les boutons π†.
Fonctions des boutons Interrupteur à glissière TV/CATV Utilisez le syntonisateur du téléviseur ou une boîte de câble pour sélectionner les canaux. Mettez cet interrupteur à la position TV pour utiliser le syntonisateur incorporé dans le téléviseur. Mettez cet interrupteur à la position CATV pour utiliser une boîte de câble. Remarque : • Reportez-vouz à la page 23 pour informations sur la programmation de votre télécommande pour l’utilisation de la boîte de câbles.
Guide de dépannage PROBLÈMES VÉRIFICATION Pas d'alimentation • Voir si le cordon secteur est débranché. • Disjoncteur ou fusibles sautés ou panne de courant. Pas d'image, pas de son • L'antenne est déconnectée. • Le mode d'entrée n'est pas sélectionné correctement. Voir page 49. • Le mode sélecteur (configuration automatique du sélecteur) est mal réglé. Voir page 30. • La station est en panne, vérifiez le bon fonctionnement des autres canaux.
Garantie Limitée JVC COMPANY OF AMERICA garantit ce produit et toutes ses pièces, sauf comme indiqué ci-après, À L’ACHETEUR DÉ DÉTAIL INITIAL comme étant EXEMPTS DE VICES DE MATÉRIAUX ET D’EXÉCUTION depuis la date de l’achat initial pendant la période indiquée ciaprès (la « période de garantie »). PIÈCES 1 AN TRAVAIL 1 AN Cette garantie limitée n’est valable que dans les cinquante (50) états des États-Unis, le District de Columbia et le Commonwealth de Porto Rico.
Garantie Limitée LA DURÉE DE TOUTE GARANTIE IMPLICITE, Y COMPRIS LA GARANTIE IMPLICITE DE COMMERCIALISATION, EST LIMITÉE À LA DURÉE DE LA GARANTIE EXPLICITE DONNÉE AUX PRÉSENTES.
Centres de Réparations Agréés SERVICE DE QUALITÉ SERVICE DE QUALITÉ COMMENT REPÉRER VOTRE CENTRE DE SERVICE JVC NUMÉRO SANS FRAIS : 1 (800) 252-5722 http://www.jvc.com Cher client, Afin de recevoir des prestations optimales de l ’appareil que vous avez acheté, veuillez lire le manuel d ’instructions avant de mettre l ’appareil en marche.Si des réparations s ’avèrent nécessaires, veuillez composer le 1 (800)252-5722 ou visitez notre site Web à www.JVC.
Spécifications MODÈLE LT-26WX84 Type Téléviseur à écran plat à affichage à cristaux liquides Système de réception Systèmes NTSC, BTSC (son multicanaux) Diffusion numérique HDTV Canaux reçus VHF 2 à 13, UHF 14 à 69 bandes Sub Mid, Mid, Super, Hyper et Ultra (Système de synthétiseur à 180 canaux) Alimentation 120 V c.a., 60 Hz Consommation 155W 26 cm / 66 pouces en diagonale coins carres format 16:9 Taille écran Haut-parleurs 6.