User's Manual

Instruction Manual
2 CAUTION
Changes or modifications not approved by us
could void the user’s authority to operate the
equipment.
• This adapter has been designed exclusively
for use with Kenwood car receivers. Do not
use this adapter with any other car receiver.
• The Wi-Fi CERTIFIED Logo is a certification
mark of the Wi-Fi Alliance.
W02-5613 (USB Wi-Fi
®
adapter)
Specifications
IEEE Standard:
802.11b/g/n
Security Support:
64/128 bit WEP /WPA & WPA2
Frequency Range:
2.401 GHz – 2.473 GHz
Transfer rates (MAX.):
802.11n (150 Mbps)
802.11g (54 Mbps)
802.11b (11 Mbps)
Output Power:
16 – 18dBm (CCK)
13 – 15dBm (OFDM)
Power Consumption:
5 V/250 mA (MAX.)
Dimensions (L × W × H):
15 mm × 19 mm × 5.6 mm
(5/8” × 3/4” × 1/4”)
Design and specifications are subject to
change without notice.
Keep the Wi-Fi adapter inserted when
using the Wi-Fi function.
When the adapter is removed, store it in a
safe place.
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications
to this equipment may cause harmful
interference unless the modifications are
expressly approved in the instruction manual.
The user could lose the authority to operate
this equipment if an unauthorized change or
modification is made.
FCC NOTE
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment may cause harmful interference
to radio communications, if it is not installed
and used in accordance with the instructions.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful
interference, and (2) This device must
accept any interference received, including
interference that may cause undesired
operation.
IC (Industry Canada) Notice
This device complies with Industry Canada
licence-exempt RSS-210 standard(s).
Operation is subject to the following two
conditions:
(1) This device may not cause interference,
and (2) this device must accept any
interference, including interference that may
cause undesired operation of the device.
The term “IC: ” before the certification/
registration number only signifies that the
Industry Canada technical specification were
met.
2 CAUTION
This equipment complies with FCC/IC
radiation exposure limits set forth for an
uncontrolled environment and meets the
FCC radio frequency (RF) Exposure Guidelines
in Supplement C to OET65 and RSS-102 of
the IC radio frequency (RF) Exposure rules.
This equipment has very low levels of RF
energy that it deemed to comply without
maximum permissive exposure evaluation
(MPE). But it is desirable that it should be
installed and operated keeping the radiator at
least 20cm or more away from person’s body
(excluding extremities: hands, wrists, feet and
ankles).
Under Industry Canada regulations, this
radio transmitter may only operate using
an antenna of a type and maximum (or
lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio
interference to other users, the antenna
type and its gain should be so chosen that
the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for
successful communication.
Wi-Fiadapter.indd2-3Wi-Fiadapter.indd2-3 12/12/1010:5512/12/1010:55