User's Manual

KCT-53U
USB ADAPTER
INSTALLATION MANUAL
© B62-XXXX-00 (W)
SUPPLIED ITEMS
• USB Adapter (USB to 9-pin RS-232)
• Distribution disc with driver software
• Installation Manual (B62-XXXX-XX)
SYSTEM REQUIREMENT
Operating System:
Windows
®
98SE, Windows
®
Me, Windows
®
2000, or Windows
®
XP
operating system.
INSTALLING THE DRIVER
1
With the computer power on, plug the KCT-53U into a USB port
on the computer. The [New Hardware Wizard] appears. Click
Next
to continue.
2
ln the dialog box that appears, leave the default choice (search
for the best drivers for your device), and click
Next
to continue.
3
 Inthedialogboxthatappears,rstputthedistributiondiscinto
your CD-ROM drive, choose [Specify a Location], then Browse
to the folder on the disc that corresponds to your version of
Windows. Click
Next
to continue.
4
ln the [Ready to install…] dialog box that appears, click
Next
to
continue.Theleswillnowbecopiedtoyourharddisk.
5
 Afterthedriveleshavebeencopiedtotheharddisk,adialog
boxwillappear,tellingyouthattheinstallationhasnished.
Click
Finish
.Windowswillnownishtheinstallation.
Note:
The KCT-53U installs as a virtual port driver on Com3. As Such
it does not support devices, such as serial mice, that require an lRQ
number or lO Address.
CONFIRMING THE INSTALLATION
Toconrmthattheadapterwascorrectlyinstalled:
1
Open the
System
folder.
2
Click the
Device Manager
tab at the top of the dialog box.
3
Click the
Plus Sign
in front of the Universal Serial Bus
Controller heading to see the Universal Serial Bus Controller
listing. If the installation completed successfully, you should
see an entry for [ATEN USB] to Serial Cable.
UNINSTALLING THE DRIVER
Windows 98SE/Me:
1
Put the distribution disc in your CD-ROM drive.
2
Open the KCT-53U folder.
3
Click
UNINST.EXE
.
Windows 2000/XP:
1
Open the
System
folder.
2
Click the
Device Manager
tab at the top of the dialog box.
3
Click the
Plus Sign
in front of the Universal Serial Bus
Controller heading to see the Universal Serial Bus Controller
listing.
4
Select [ATEN USB] to Serial Cable.
5
Click the
Remove
button.
PERIPHERAL INSTALLATION
1
With the computer power on and the KCT-53U adapter already
plugged into the computer’s USB port, plug the peripheral into
the KCT-53U, then turn the peripheral ON.
2
Follow the installation Wizard’s on-screen instructions to
complete the installation.
Note:
♦
 Thisprocedureonlyoccursthersttimeyouconnectaperipheral.
Ifyourperipheralwaspreviouslyconnectedandconguredforthe
RS-232 (COM) port, after you perform the Adapter installation and
click Finish (see above), the driver will detect the peripheral and
install it automatically.
♦
Under Windows 2000/XP, if you connect a modem, you must
specify it as a Standard Modem.
♦
Please access the following URL for support information:
http://www.kenwood.com/......
Copyrights
• Windows is a registered trademark of Microsoft Corporation in
the United States and/or other countries.
• Other product and company names mentioned herein may be
the trademarks of their respective owners.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
One or more of the following statements may be applicable to this
equipment.
FCC WARNING
This equipment generates or uses radio frequency energy. Changes
ormodicationstothisequipmentmaycauseharmfulinterference
unlessthemodicationsareexpresslyapprovedintheinstruction
manual. The user could lose the authority to operate this equipment if
anunauthorizedchangeormodicationismade.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY
THE FCC
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer for technical assistance.