IMPRESSA F70 / F707 Instructions for use
Legend: 䡲 䡲 DISPLAY: serves as information. DISPLAY: please follow the instructions shown.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig.
Fig. 19 Fig. 20 Temp. max. Fig. 21 Temp. min.
9 3 Control elements 7 1. Rotary Switch 2. Illuminated ring 3. ON / OFF symbol 4 5 6 8 21 4. 1 LARGE CUP symbol 22 23 5. 1 COFFEE symbol 6. 1 ESPRESSO symbol 11 12 10 13 9 2 14 7. MAINTENANCE symbol 8. START symbol 9. Display dialog system 10. Water tank with handle 11. Filler funnel for pre-ground coffee 12. Bean tank cover 13. Aroma preservation cover 1 14. Steam / hot water draw-off tap 15/16 17 18 15. Profi-Auto-Cappuccino Frother with milk pipe 16.
Contents 1. Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1.1 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1.2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2. Preparing the IMPRESSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2.1 Check supply voltage . . . .
Introduction Thank you for purchasing the IMPRESSA. To ensure perfect functioning of your IMPRESSA, carefully read this operating manual and keep it for future reference. Should you need more information or if you encounter particular problems not specified in these operating instructions in sufficient detail, either contact us directly or contact your local authorized dealer. You will also find useful tips on operation and maintenance of your IMPRESSA on our website at www.jura.com. 1.
The grinding degree may only be adjusted while the grinding gear is running. 2.3 Fill water tank Only use fresh, cold water. Never fill in milk, mineral water or other liquids. 䡲 Remove the water tank and rinse it with cold tap water thoroughly (Fig. 4). 䡲 Then fill the water tank and reinstall it. Make sure to install the tank properly, it must engage audibly. 䡲 Open the bean tank cover (12) and remove the aroma preservation cover (13). 䡲 To adjust the grinding degree, turn the Rotary Switch (Fig.
䡲 Confirm your selection by pressing the Rotary Switch (1) (Fig. 17). 䡲 4. Adjusting the water hardness FILL WATER Water is heated in the IMPRESSA. As a result, calcification occurs during normal use and is indicated automatically. Before using the IMPRESSA for the first time the hardness of the water used must be adjusted. Use the supplied test sticks for this. 䡲 Fill the water tank (10) with fresh water. 䡲 OPEN TAP 䡲 Place a receptacle under the Professional Cappuccino Frother (15) (Fig. 10).
䡲 FILTER – 䡲 Turn the Rotary Switch (1) until the following message is displayed: 䡲 HARDNESS 䡲 Now press the Rotary Switch (1) to start the programming. 䡲 LEVEL 3 䡲 Turn the Rotary Switch (1) until the required level is displayed. 䡲 For example, LEVEL 4 䡲 Press the Rotary Switch (1) to confirm the required level. 䡲 HARDNESS 䡲 Turn the Rotary Switch (1) until EXIT appears 䡲 Press the Rotary Switch (1) to leave the programming mode. 䡲 READY 5.
䡲 HEATING UP 䡲 READY Now you have activated the filter. In Programming Mode the water hardness selection function is no longer displayed. 5.2 Replacing the filter Draw off 1/2 litre of water to rinse filter completely. In order to ensure perfect operation, close tap (14) only after the display says CLOSE TAP After drawing off approx. 50 litres, the filter cartridge will be used up. A message requesting you to replace the filter will appear on the display.
䡲 Touch the symbol (3). 䡲 HEATING UP 䡲 PRESS MAINT. 䡲 Touch the symbol (7). 䡲 RINSING 䡲 READY You can adjust the water quantity in steps of 5 ML using the Rotary Switch (1). 䡲 READY 䡲 Turn the Rotary Switch (1) until the required water quantity is displayed. 䡲 For example, 120 ML 8. Making 1 cup of coffee 6.1 Rinsing the IMPRESSA without display request 䡲 Press the Rotary Switch (1) until FILTER – /⻫ appears. You can choose from 3 different coffee strengths.
䡲 䡲 Touch the 䡲 䡲 Touch the coffee draw-off symbol of your choice twice STRONG (8) symbol 160 ML (water quantity last adjusted). 䡲 2 COFFEE 䡲 120 ML (water quantity last adjusted). 䡲 The illuminated ring (2) is active. 䡲 The illuminated ring (2) is active. 䡲 Turn the Rotary Switch (1) until the required amount of coffee water appears on the display (9). 䡲 Turn the Rotary Switch (1) until the required amount of coffee water appears on the display (9). 䡲 e.g. 120 ML 䡲 e.g.
䡲 Open the cover of the filler funnel for pre-ground coffee (11). 䡲 䡲 䡲 Place a cup under the replaceable hot water nozzle (16). FILL POWDER 䡲 Fill 1 or 2 level spoonfuls of pre-ground coffee in the filler funnel for pre-ground coffee (11) (Fig. 15) and close the cover. 䡲 SELECT KEY 䡲 (8) symbol 120 ML (water quantity last adjusted) 䡲 The illuminated ring (2) is active.
Make sure that the nozzle is correctly fitted when drawing steam. If the nozzle becomes blocked with particles of milk residue or is incorrectly assembled, a danger can arise during use whereby the nozzle may jump off. Due to the system design, some water will escape at first when steam is drawn. However, this will not affect the result in any way. When drawing steam, spluttering can occur at the start. The nozzle becomes hot in use. Avoid any direct skin contact.
A useful addition is available for all lovers of milk specialities in the form of high-quality vacuum milk containers. They keep the milk cool the whole day long and are optimally suited to the design of your IMPRESSA. All original JURA accessories can be obtained from the specialist shop. 䡲 Turn the selector switch of the Professional Cappuccino Frother (15) to the milk foam position (Fig. 19). 䡲 READY 䡲 Open the steam / hot water draw-off tap (14) (Fig. 12). The milk foam is prepared.
䡲 Thoroughly rinse all parts of the nozzle under running water. 䡲 Close the steam / hot water draw-off tap (14). 䡲 Reassemble the Professional Cappuccino Frother (15) and refit it on to your IMPRESSA. 䡲 13.4 Cleaning the Professional Cappuccino Frother To ensure that the Professional Cappuccino Frother (15) functions perfectly, you should clean it daily if you have prepared milk foam or hot milk. You will not be prompted by your IMPRESSA to clean the Professional Cappuccino Frother (15).
15. Programming When your IMPRESSA leaves the factory it is adjusted such that you can draw off coffee without having to change any settings. However, you can programme various parameters individually. 15.2 Programming the water hardness Refer to Chapter 4 ‘Adjusting the water hardness’. 15.
䡲 READY 䡲 Press the Rotary Switch (1) until FILTER – /⻫ appears 䡲 Turn the Rotary Switch (1) to change the temperature from HIGH to NORMAL (or vice versa). 䡲 NORMAL 䡲 The illuminated ring (2) is active. 䡲 Press the Rotary Switch (1) to save the setting. 䡲 Turn the Rotary Switch (1) until Aroma is displayed. 䡲 䡲 䡲 Turn the Rotary Switch (1) until EXIT appears AROMA 䡲 Press the Rotary Switch (1).
䡲 Turn the Rotary Switch (1) to select the minutes. 䡲 2:05 䡲 Press the Rotary Switch (1) to confirm the hour settings and to activate the minutes. 䡲 Press the Rotary Switch (1) to save the setting. 䡲 䡲 䡲 Turn theRotary Switch (1) to select the minutes. TIME 12:-- 䡲 Turn the Rotary Switch (1) until EXIT appears 䡲 䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 Turn the Rotary Switch (1) to adjust the hours. 䡲 E.g press draw-off key 1 cup of coffee 䡲 䡲 1.0 HR 䡲 Press the Rotary Switch (1) to save the setting. 䡲 䡲 Press the Rotary Switch (1) to leave the programming mode. 䡲 READY 20 You can check the number of pre-ground cups of coffee by opening the filler funnel for pre-ground coffee (11). OFF AFT. HR 䡲 Turn the Rotary Switch (1) until EXIT appears (5). 䡲 Touch one of the symbols made 2 cups of coffee.
䡲 LANGUAGE 䡲 Turn the Rotary Switch (1) until EXIT appears 15.12 Programming the display for ML/OZ 䡲 READY 䡲 Press the Rotary Switch (1) to leave the programming mode. 䡲 Press the Rotary Switch (1) until FILTER – /⻫ appears 䡲 䡲 The illuminated ring (2) is active. READY 15.11 Programming Display 24H/AM/PM 䡲 Turn the Rotary Switch (1) until DISPLAY appears 䡲 䡲 Press the Rotary Switch (1) READY 䡲 Press the Rotary Switch (1) until FILTER – /⻫ appears 䡲 䡲 The illuminated ring (2) is active.
䡲 Press the Rotary Switch (1) to leave the programming mode. 䡲 READYM 16. Maintenance 16.1 Filling in water 䡲 FILL WATER If this information is displayed, drawing off products is no longer possible. Refill water as described in Chapter 2.3. 䡲 16.2 Emptying the coffee grounds container EMPTY GROUNDS If this message appears on the display, you can no longer draw off coffee. You must empty the coffee grounds container (18) first (Fig. 13). 䡲 Carefully take out the drip tray (20), it is filled with water.
If the water tank shows signs of scaling, remove the scaling using a commercial descaling agent. Take out the water tank (Fig. 4). 16.6 Cleaning the IMPRESSA After 200 draw-off operations or after 80 rinsing operations, the IMPRESSA must be cleaned. A message appears on the display, telling you to start the cleaning programme. You can still draw off coffee or hot water/steam. However, we recommend that you should clean the machine (Chapter 17) within the next few days.
17. Cleaning 䡲 CLEANING Your IMPRESSA features an integrated cleaning program. The cleaning operation will take some 15 min. 䡲 FILL TABLET Original JURA cleaning tablets which are specially designed for the cleaning program of your IMPRESSA are available at your authorized dealer. Please note that machine defects or residues in the water cannot be excluded if you use inappropriate cleaning agents.
䡲 Press the Rotary Switch (1) again to confirm. 䡲 Touch the 䡲 䡲 EMPTY TRAY 䡲 The program ‘Clean’ is now active. Now proceed as described in Chapter 17 from EMPTY TRAY onwards. 18. Descaling Your IMPRESSA features an integrated descaling program. The cleaning operation will take some 40 min. Original JURA descaling tablets which are specially designed for the descaling program of your IMPRESSA are available at your authorized dealer.
䡲 Insert the tray (20) again. 䡲 18.1 Decalcifying without display request FILL WATER Rinse the water tank thoroughly and fill it with cold, fresh tap water. Install it again. 䡲 OPEN TAP Decalcifying without display request is only possible if the CLARIS plus filter is NOT programmed. 䡲 Press the Rotary Switch (1) until FILTER – appears. 䡲 Turn the Rotary Switch (1) until MAINTENANCE appears. 䡲 Open the steam / hot water draw-off tap (14) (Fig. 12). 䡲 Press the Rotary Switch (1) to confirm.
20. Tips for perfect coffee Height-adjustable coffee spout (17) You can adjust the height of the coffee spout to the size of your cups (Fig. 3) Grinding degree Refer to Chapter 2.5 ‘Adjusting the grinding gear’. Preheating cups You can preheat the cups using hot water or steam. The smaller the coffee you want to draw off, the more important preheating is. Sugar and cream Stirring coffee/tea will result in heat being released.
21. Messages Cause Remedy Water tank is empty. Refill water Float defective Rinse or de-scale water tank Bean tank is empty. Refill beans Although you have refilled beans, the message still appears. Draw off a cup of coffee. The message will disappear only after you have drawn off a cup of coffee Coffee grounds container full Empty coffee grounds container Tray reinstalled too early after emptying Wait 10 sec.
22.
23. Legal information 24. Technical data These operating instructions contain all the information required for using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance. These operating instructions cannot cover any conceivable application. The machine was designed for private household use.
Art. 66380 – 5/07 JURA-Elektroapparate AG – Kaffeeweltstrasse 10 – CH-4626 Niederbuchsiten www.jura.