User's Guide

Website : www.juplink.com
Email : [e-mail]
Before Setting
To customize your wireless network
connection and other advanced repeater
settings, please go to
www.Juplink.com/Support/
to download EC4-1200 updated Firmware
and User Guide for more information.
Operating Conditions
Working Temperature: 0~45°C / 32~113°F
Working Humidity: 10%~90% RH
(No condensation)
Storage Temperature:-40~85°C / -40~185°F
Storage Humidity: 5%~95% RH
(No condensation)
Quick Start Guide
V A N I N
EC4-1200
Wi-Fi Extender
LED Status Indicators
Wi-Fi Signal Strength
Indicator LED
WPS
LED
2.4G / 5G Singal LED
PWR
LED on WPS is enabled and connected
LED Flashing WPS is enabled and in connection
LED off
LED on
LED Flashing
LED off
LED on
LED off
Power on
Power off
Status Meaning
Function not enabled or Powered off
No Transferming data
Transferming data
Equipment Connection Normal
One LED on Weak reception, strength below 25%
Two LED on Good reception, strength below 50~75%
Three LED on Excellent reception, strength below 100%
No Wi-Fi signal or Power off
Method 1 : Extending Your Wi-Fi Network Using Web UI
②Extend Your Wi-Fi Network
1. Connect your Wi-Fi device to the repeater’s Wi-Fi network
Juplink-EC4-1200_5G or Juplink-EC4-1200.
2. Lauch a web browser on the device which has been connected
to the repeater,Enter 192.168.0.2 in the address bar to log in.
3. Username:admin / Passwrod:admin
4. Modify your SSID and Password
( Note :It may takes a few second to scan the network )
Ensure that Mobile Data ( if any ) is disabled.
WLAN
Juplink-EC4-1200
Juplink-EC4-1200_5G
http://192.168.0.2
Login 192.168.0.2” VANIN EC4-1200 repeater
Username
Password
admin
admin
Cancel Login
6. Enter the password of the Wi-Fi network you want to extend.
7. Scroll to the bottom of the page and select “Save&Apply”.
②Extend Your Wi-Fi Network
③Relocate the Repeater
CancelSave&Apply
Wait a moment, the Change setting successfully! page appears
Method 2 : Extending Your Wi-Fi Network Using WPS
You can use Method 2 if your router has a WPS button. otherwise, use Method 1
②Extend Your Wi-Fi Network
WPS
POWER
WPS
2.4G 5G
1. Press the WPS button on the router and within 2minutes press the WPS button on the repeater
2. Wait until the 2.4G / 5G Singal LED turns solid green
1. For better performance, plug the repeater into an outlet halfway
between the router and the Wi-Fi dead zone.
The location you choose must be within the range of your existing
Wi-Fi network
2. Wait until the 2.4G / 5G Singal LED turns solid green. or the
Wi-Fi Signal Strength Indicator shows at least Two LEDs on
①Power on the Repeater
1. Plug the repeater into a power outlet near the router
2. Wait until the 2.4G / 5G Singal LED turns solid green
①Power on the Repeater
1. Plug the repeater into a power outlet near the router
2. Wait until the 2.4G / 5G Singal LED turns solid green
POWER
WPS
2.4G 5G
POWER
WPS
2.4G 5G
POWER
WPS
2.4G 5G
POWER
WPS
2.4G 5G
5. Select a Wi-Fi network (SSID) you want to extend
Note：Default SSID and password are automatically copied from that of the router for both 2.4 GHz and 5 GHz networks. If you wish to modify
these settings, Click the check mark and then enter the SSID and password that you wish to apply to the extended Wi-Fi network(s).
Juplink-RX4-1500
Juplink-RX4-1500_5G
Juplink-Router
FCC ID：2AT9Z-EC4-1200