Instructions

ManualsBrandsJunsi ManualsBatteries & ChargersScale model multifunction charger 30 A Junsi Li-ion, LiFePO, LiHV, LiPolymer, NiMH, NiCd, Lead-acid, NiZn

d) Setup location

• Only use in temperate climates. Refer to the technical data section for information on the

permitted ambient conditions.

• The charger must only be used in dry, enclosed indoor areas. It must not become damp or

wet. Never place the product next to a bathtub, shower or other sources of moisture.

• Avoid direct sunlight, intense heat and cold temperatures. Keep the product away from dust

and dirt. The same applies to connected batteries.

• Do not use the product in rooms or areas where ammable gas, vapours or dust may be

present, as this may cause an explosion!

• Place the charger on a clean, level surface. Do not place the charger on ammable materi-

als (e.g. a carpet or tablecloth). Always use a non-ammable, heatproof surface.

• Keep the charger away from ammable or combustible materials (e.g. curtains).

• Never cover the product, as this may cause it to overheat and catch re. Do not insert any

objects into the ventilation slots on the charger.

• If the product has a fan, do not interfere with the built-in fan.

• Always use suitable protection when placing the charger on valuable furniture, otherwise it

may cause scratch/pressure marks or discolour the furniture.

• Do not use the charger inside vehicles.

• Do not use the charger in the immediate vicinity of strong magnetic/electromagnetic elds,

transmitter aerials or HF generators. These may affect the electronic control system.

• Do not place any objects that contain liquid (e.g. vases or plants) on or next to the charger,

battery or cable.

• Liquids that get into the interior of the charger (or inside the connection sockets) may de-

stroy the charger and cause a re.

• If liquid does get inside the device or the connection sockets, disconnect the charger from

the power supply. Remove the battery from the charger. Discontinue use and take the

charger to a specialist repair centre.

e) Cables

• Make sure that cables are not pinched or damaged by sharp edges. Do not place any

objects on cables.

f) Operation

• The charger is powered by stabilized direct voltage (e.g. an external car lead-acid battery

or a suitable mains adapter). Make sure the power supply complies with the details given

in the technical data.

• Never wear metal or conductive objects (e.g. jewellery such as necklaces, bracelets or

rings) to avoid short circuits, which can lead to re or explosion.

• Never leave the product unattended during use.

• Ensure there is sufcient ventilation during use; never cover the charger. Ensure that there

is a sufcient distance (min. 20 cm) between the charger and other objects, otherwise the

charger may overheat and cause a re!

• Only charge battery types listed in the technical data.

• To prevent re or explosion, always connect the cable to the charger before connecting a

battery. When disconnecting, proceed in the reverse order – disconnect the battery from the

charging cable, and then unplug the cable from the charger.

• Do not connect several chargers together.

• Only connect a single battery/battery pack to the charger.

• If you do not plan to use the charger for an extended period, disconnect any connected bat-

teries from the charger, and then disconnect the charger from the power supply.

• Never use the product immediately after it has been brought from a cold room into a warm

one. This may generate condensation, which can cause the charger to malfunction or dam-

age the interior components.

• Allow the product to reach room temperature before using it. This may take several hours.

• If you suspect that safe operation is no longer possible, discontinue use immediately and

prevent unauthorized use. Disconnect the charger from the power supply.

• Safe operation is no longer possible if the product is visibly damaged or stops working, or

if the product was stored in unfavourable conditions for an extended period or mishandled

during transport.

g) Cleaning and Storage

• Before you clean the charger, disconnect any connected batteries.

• Before you clean, disconnect the power supply from the charger.

• Keep the product in a cool, dry place out of the reach of children.

Quick Start Guide

Charger 30 V / 30 A

Item No. 1900460

Notes to all users

For features not listed in this Quick Start Guide (e.g. programming, set up, servo testing,

rmware update, or USB & SD card usage), refer to the full operating instructions on the

supplied CD or download them as outlined in chapter Full Operating Instructions.

Remark: Features/Instructions not listed in this Quick Start Guide are intended for users

that have an in-depth knowledge of battery chemistry (types) and battery charging tech-

niques. Programming of settings allows users to adjust the charging techniques, and users

without such knowledge should never attempt to meddle with any such setting.

Full Operating Instructions

Download the latest full operating instructions at www.conrad.com/downloads

or scan the QR code shown. Follow the instructions on the website.

Intended use

The product is designed to charge different types of rechargeable batteries.

Never leave the product unattended during use.

It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bath-

rooms, must be avoided under all circsumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use

the product for purposes other than those described above, the product may be damaged. In

addition, improper use can result in short circuits, res, electric shocks or other hazards. Read

the instructions carefully and store them in a safe place. Make this product available to third

parties only together with its operating instructions.

This product complies with the statutory national and European requirements.

All company names and product names are trademarks of their respective owners. All rights

reserved.

Explanation of symbols

The symbol with the lightning in the triangle is used if there is a risk to your health,

e.g. due to an electric shock.

The symbol with the exclamation mark in the triangle is used to indicate important

information in these operating instructions. Always read this information carefully.

The arrow symbol indicates special information and advice on operation.

Safety instructions

Read these instructions and the full operating instructions carefully and espe-

cially observe the safety information. If you do not follow the safety instruc-

tions and information on proper handling, we assume no liability for any re-

sulting personal injury or damage to property. Such cases will invalidate the

warranty/guarantee.

a) General information

• The unauthorized conversion and/or modication of the product is prohibited for safety and

approval reasons. Never dismantle the product.

• Maintenance, modications and repairs must only be completed by a technician or an au-

thorised repair centre.

• Do not leave packaging material lying around carelessly, as it may become dangerous

playing material for children.

• If you are not sure how to operate the product correctly, or if you have any questions that are

not answered in the operating instructions, contact us or another specialist.

• Handle the product with care. Impacts or falls (even from a low height) may damage the

product.

b) Children

• This product is not a toy and must be kept out of the reach of children.

• The product must be installed, used and stored in areas that are inaccessible to children.

c) Facilities

• In schools, educational facilities, hobby and DIY workshops, the product must be operated

under the supervision of qualied personnel.

• Always comply with the accident prevention regulations for electrical equipment when using

the product in industrial facilities.

Summary of content (4 pages)

PAGE 1
d) Setup location • Only use in temperate climates. Refer to the technical data section for information on the permitted ambient conditions. Quick Start Guide Charger 30 V / 30 A Item No. 1900460 Notes to all users For features not listed in this Quick Start Guide (e.g. programming, set up, servo testing, firmware update, or USB & SD card usage), refer to the full operating instructions on the supplied CD or download them as outlined in chapter Full Operating Instructions.
PAGE 2
Battery information There are numerous hazards associated with the use of rechargeable batteries. Always observe the following safety information when handling rechargeable batteries. In addition, ensure that you observe any additional safety information provided by the battery manufacturer. a) Children • Rechargeable batteries are not toys. Keep batteries out of the reach of children. • Do not leave batteries lying around, as they constitute a choking hazard for children and pets.
PAGE 3
Quick Start Guide b) Selecting an input source 1. While the startup screen shows (approx. 5 seconds), press < source. Confirm by pressing any other button. > to select the input Battery Types The below tables gives details on the battery types the charger can charge. Type LiPo Lilo LiFe LiHV LTO NiZn User Pb NiCd/ NiMh Nominal Charge voltage voltage 3.7V 3.85V – 4.35V Default: 4.20V 3.6V 3.75V – 4.35V Default: 4.10V 3.3V 3.30V – 3.80V Default: 3.60V 3.8V 3.90V – 4.40V Default: 4.35V 2.4V 2.50V – 3.
PAGE 4
e) Error Handling and Messages -- LiXX battery: > 3C -- NiMH/NiCd battery: > 2C Refer to the full operating instructions for full details on errors. -- Pb battery: > 0.3C • If an error is detected while running a program, charging on the affected channel immediately stops. You will be informed by a buzzer and a pop-up with error information. -- NiZn battery: >2C • Press < Press < > or < > to choose Run Program. The common parameters are in grey. > to change them. • Press < > to exit the interface.