Trapeze Mobility Point™ 400 Installation Guide Part Number 730-9502-0134, Revision A
Trapeze Networks, Inc. 5753 W. Las Positas Blvd. Pleasanton, CA 94588 Tel: +1 925-474-2200 Fax: +1 925-251-0642 Toll-Free: 877-FLY-TRPZ (877-359-8779) www.trapezenetworks.com © 2006 Trapeze Networks, Inc. All rights reserved.
Customer Service For general information about Trapeze Networks Mobility System™ products and services, visit www.trapezenetworks.com. For warranty, license, and support information, visit the following sites: ● Warranty and software licenses. Current Trapeze Networks warranty and software licenses are available at www.trapezenetworks.com/support/ warranty.asp. ● Support services. For information about Trapeze support services, visit www.trapezenetworks.com/support/.
TAC Response Time TAC responds to service requests as follows: Contact method Priority Response time Telephone Emergency One hour Non-emergency Next business day Email Non-emergency Next business day Information to Have Available To expedite your service request, have the following information available when you call or write to TAC for technical assistance: iv ● Your company name and address ● Your name, telephone number, cell phone or pager number, and email address ● Name, model, and seria
Contents Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii 1 Introducing the Trapeze Networks Mobility System . . . . . . . . . . . . . . . . 1 Trapeze Networks Mobility System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety and Advisory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . .
Junction Box Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Solid Wall or Ceiling Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Tabletop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Connecting an MP to an External Antenna . . . . . . . . . . . . . . . . . . . . . . 49 Connecting an MP to an MX Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Verifying MP Health . . . . .
1 Introducing the Trapeze Networks Mobility System Trapeze Networks Mobility System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 This guide shows you how to install a Trapeze Networks™ Mobility Point™ (MP™) access point in a Trapeze Networks Mobility System™ wireless LAN (WLAN).
Documentation Chapter 1 The Trapeze Networks Mobility System consists of the following components: ● RingMaster tool suite—A full-featured graphical user interface (GUI) application used to plan, configure, deploy, and manage a WLAN and its users ● One or more Mobility Exchange™ (MX™) switches—Distributed, intelligent machines for managing user connectivity, connecting and powering Mobility Point (MP) access points, and connecting the WLAN to the wired network backbone ● Multiple Mobility Point™ (MP™)
Documentation Chapter 1 Installation ● Trapeze Mobility Exchange Hardware Installation Guide. Instructions and specifications for installing an MX switch ● Trapeze Mobility System Software Quick Start Guide. Instructions for performing basic setup of secure (802.1X) and guest (Web AAA) access, for configuring a Mobility Domain for roaming, and for accessing a sample network plan in RingMaster for advanced configuration and management ● Trapeze Mobility Point MP-422 Installation Guide (this document).
Documentation Chapter 1 Safety and Advisory Notices The following kinds of safety and advisory notices appear in this manual. (For translations of the warning conventions and of all warnings in this manual, see Trapeze Regulatory Information.) Caution! This situation or condition can lead to data loss or damage to the product or other property. Warning! This situation or condition can cause injury. Warning! High voltage. This situation or condition can cause injury due to electric shock.
Documentation Chapter 1 Text and Syntax Conventions Trapeze manuals use the following text and syntax conventions: Convention Use Monospace text Sets off command syntax or sample commands and system responses. Bold text Highlights commands that you enter or items you select. Italic text Designates command variables that you replace with appropriate values, or highlights publication titles or words requiring special emphasis. Menu Name > Command Indicates a menu item that you select.
Documentation Chapter 1 6 Trapeze Mobility Point Installation Guide
2 MP Overview External Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 A Trapeze Networks Mobility Point (MP) access point provides IEEE 802.11 wireless access to the network. MP access points are designed for use with a Trapeze Networks Mobility Exchange (MX) switch. MP access points require hardware installation only.
External Hardware Features Chapter 2 External Hardware Features Figure 1 and Figure 2 show the external hardware features of the MP-422. Figure 1. MP Access Point Model MP-422—Top View Diameter 16.76 cm (6.6 inches) Figure 2. 840-9502-0040 Height 6.10 cm (2.4 inches) MP Access Point Model MP-422—Bottom View External antenna connectors Kensington security slot 802.11b/g 840-9502-0007 Unlock 802.
External Hardware Features Chapter 2 Cable Ports The MP-422 has two RJ-45 ports. (See Figure 2.) Each port provides a 10/100BASE-TX Ethernet connection to an MX switch. The connection can be direct to an MX-switch or indirect through an intermediate Layer 2 or Layer 3 network. The MP receives power and data through the RJ-45 ports. Use a Category 5 (Cat 5) cable with straight-through signaling and standard RJ-45 connectors to connect an MP to an MX switch or other device in the network.
External Hardware Features Chapter 2 External Antenna Connectors The MP-422 has connectors for attaching optional external antennas. (See Figure 2.) Table 1 lists the external antenna models. Table 1. Trapeze External Antenna Models Model Type Gain ANT-7360 802.11a 802.11b/g Beamwidth Horizontal Vertical 8 dBi 360° 15° 6 dBi 360° 25° 8 dBi 360° 15° 802.11b/g 6 dBi 360° 22° 802.11a 14.5 dBi 60° 14° ANT-5120 (ASTN6T) 802.11a 12.5 dBi 120° 14° ANT-5180 (ASTN6H) 802.11a 10.
External Hardware Features Chapter 2 Figure 3. External 802.11b/g Antennas Model ANT-1120 Model ANT-1180 840-9502-0077 Model ANT-1060 The 802.11a external antennas look similar to the 802.11b/g model ANT-1180, but each has a reflector plate specific to the model number. You can identify an 802.11a external antenna’s model by looking on the back of its reflector plate. Do not reverse or remove the reflector plate. It is required for antenna operation.
External Hardware Features Chapter 2 Kensington Security Slot Models MP-422 has a slot for attachment of a Kensington security cable. The cable is not included with the MP but can be ordered separately. MP Mounting Options You can mount an MP access point on any of the following types of surfaces: ● Suspended T-bar ceiling ● Junction box ● Solid surface wall or ceiling ● Tabletop Note. The solid surface mounting option requires Cat 5 cable that does not have strain relief.
External Hardware Features Chapter 2 Table 2. MP Access Point LEDs—MP-422 LED Appearance Meaning Health Solid green All the following are true: • Management link with an MX switch is operational. • MP access point has booted. • MP access point has received a valid configuration from an MX switch. • At least one radio is enabled or is in sentry mode. Solid amber MP access point is waiting to receive boot instructions and a configuration file from an MX switch.
Connection Options Chapter 2 Connection Options You can connect an MP access port directly to an MX switch port or indirectly to MX switches through an intermediate Layer 2 or Layer 3 network. In either case, use Category 5 (CAT 5) cable with straight-through signaling for each MP connection. You also can provide data link redundancy by connecting both of its ports directly to MX switch ports or indirectly to MX switches through the network.
3 Installing and Connecting an MP-422 Unpacking an MP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Installation Requirements and Recommendations . . . . . . . . . . . . . . . . . . . . . 18 Installing an MP-422 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Connecting an MP to an MX Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Verifying MP Health . . . . . . . . . . . . . . . . . . . . .
Unpacking an MP Chapter 3 Unpacking an MP The shipping carton for an MP access point contains the following items: ● One MP access point ● Mounting kit: ● 16 ● One universal mounting bracket (attached to the MP) ● One paper mounting template (used for marking cutting areas and screw holes) ● One two-piece 14.2-mm (9/16-inch) T-bar clamp ● One two-piece 15.9-mm (5/8-inch) T-bar clamp ● One two-piece 23.
Unpacking an MP Chapter 3 Figure 5 shows the contents of the shipping carton for model MP-422. Figure 5. MP-422 Shipping Carton Contents Mounting template Rubber feet T-bar clamps Universal mounting bracket 840-9502-0001 Mobility point Mounting hardware Before you begin installation: 1 Open the carton and carefully remove the contents, if you have not already done so. 2 Place the packing materials back in the carton and save the carton.
Installation Requirements and Recommendations Chapter 3 Installation Requirements and Recommendations For best results, follow these requirements and recommendations before installing an MP access point. RingMaster Network Plan and Work Orders If you are using RingMaster to plan your Trapeze Networks Mobility System installation, you might want to create and verify a network plan for the entire Trapeze network installation and generate an MP work order, before installing MP access points.
Installation Requirements and Recommendations Chapter 3 (For information about connecting an MP access point to an MX switch port, see “Connecting an MP to an MX Switch” on page 50.) Wall Installation Recommendations If you plan to install an MP on a partial wall or other vertical surface, orient the top of the access point (the side with the LEDs) toward the intended coverage area. The radio antennas transmit through the top of the access point but not through the bottom (where the bracket is).
Installation Requirements and Recommendations Chapter 3 Warning! Do not operate the MP access point near unshielded blasting caps or in an otherwise explosive environment unless the device has been modified for such use by qualified personnel. Warning! Do not touch or move the MP access point when the antennas are transmitting or receiving.
Installation Requirements and Recommendations Chapter 3 Cat 5 cable with straight-through signaling must be installed at the site before you install an MP access point. A single connection requires one cable. A dual-homed connection requires two cables. Table 3 lists the pin signals for 10/100 Ethernet straight-through wiring. Pins 4, 5, 7, and 8 are used when Trapeze Power over Ethernet (PoE) is enabled on the port. RD means Receive Data and TD means Transmit Data. Table 3.
Installing an MP-422 Chapter 3 Installing an MP-422 To install an MP-422, use one of the procedures in this section. Installation Hardware and Tools Table 4 lists the mounting hardware and tools required for each type of installation. Table 4.
Installing an MP-422 Chapter 3 Table 4.
Installing an MP-422 Chapter 3 Figure 6. Universal Mounting Bracket Port connector opening T-bar flanges 840-9502-0018 Screw holes Suspended Ceiling Installation—Flush Ceiling Tiles (For required mounting hardware and tools, see Table 4 on page 22.) 1 Select an installation location that is centered over a T-bar in the ceiling. 2 Cut a hole as follows in the ceiling tile for the Cat 5 cable(s): 3 24 a Place the mounting template over the area where you plan to install the MP access point.
Installing an MP-422 Chapter 3 4 Figure 7. Install the 14.2-mm (9/16-inch) T-bar clamp onto the ceiling T-bar as shown in Figure 7. a Slide each half of the clamp onto the T-bar so that the clamp lip is fully on the T-bar. b Slide the two halves of the clamp toward each other until the tabs are inserted completely into the holes and the clamp fits snugly on the T-bar.
Installing an MP-422 Chapter 3 Step 5—Unlocking the Bracket 840-9502-0011 Figure 8. 6 Remove the bracket as shown in Figure 9. Step 6—Removing the Bracket 840-9502-0008 Figure 9. 7 Install the universal mounting bracket as follows onto the T-bar or T-bar clamp: a 26 As shown in Figure 10, place the universal mounting bracket against the T-bar or clamp so that the two screw holes face downward and the two T-bar flanges face upward and are adjacent to the T-bar edges.
Installing an MP-422 Chapter 3 Figure 10. Step 7—Top View Universal mounting bracket T-bar 840-9502-0005 Port connector opening (Viewed from above ceiling tiles, looking down.) b Properly align the bracket for mounting by placing the bracket so that its port connector opening is to the left of the hole you cut for the cables. c Rotate the universal mounting bracket clockwise until the flanges snap into place on the T-bar or clamp as shown in Figure 11. Figure 11.
Installing an MP-422 Chapter 3 9 10 11 Insert the Cat 5 cable(s) into the connector(s): ● For a single connection, use the connector for port 1. ● For redundancy, insert one cable into each connector. Install the Kensington lock, if you plan to use one. a Loop the Kensington lock’s cable around an object that cannot be moved or damaged by a person pulling on the cable. b Insert the key into the Kensington lock. c Insert the Kensington lock into the security slot on the MP.
Installing an MP-422 Chapter 3 12 Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point as shown in Figure 13. Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it. Figure 13.
Installing an MP-422 Chapter 3 Suspended Ceiling Installation—Drop Ceiling Tiles (For required mounting hardware and tools, see Table 4 on page 22.) 1 Select an installation location that is centered over a T-bar in the ceiling. 2 Cut a hole as follows in the ceiling tile for the Cat 5 cable(s): 3 a Place the mounting template over the area where you plan to install the MP access point. b Use the box cutter to cut along the line marking the opening for the port connectors.
Installing an MP-422 Chapter 3 Figure 15. Step 3—Installing the T-bar Clamp for a 15.9-mm (5/8-inch) T-bar T-bar Slide together 840-9502-0066 T-bar clamp halves 4 Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point as shown in Figure 16.
Installing an MP-422 Chapter 3 5 Remove the bracket as shown in Figure 17. 840-9502-0008 Figure 17. Step 5—Removing the Bracket 6 32 Install the universal mounting bracket as follows onto the T-bar clamp: a As shown in Figure 18, place the universal mounting bracket against the T-bar clamp so that the two screw holes face downward and the two T-bar flanges face upward and are adjacent to the T-bar edges.
Installing an MP-422 Chapter 3 Figure 18. Step 6—Top View Universal mounting bracket T- bar 840-9502-0012 T-bar clamps (attached to T-bar) Port connector opening (Viewed from above ceiling tiles, looking down.) Figure 19. Step 6—Bottom View Port connector opening Universal mounting bracket 840-9502-0004 T-bar 7 Pull the Cat 5 cable(s) about 15 cm (about 6 inches) out of the hole in the ceiling tile and through the port connector opening to create enough slack to insert the cable(s).
Installing an MP-422 Chapter 3 9 10 Install the Kensington lock, if you plan to use one. a Loop the Kensington lock’s cable around an object that cannot be moved or damaged by a person pulling on the cable. b Insert the key into the Kensington lock. c Insert the Kensington lock into the security slot on the MP. d Rotate the key right or left to secure the lock to the MP. e Pull on the lock to verify that it is secured to the MP. f Remove the key.
Installing an MP-422 Chapter 3 Figure 21. Step 10—Locking the Bracket Lock 840-9502-0006 T-bar 12 To ensure that the MP access point is fully locked onto the bracket, gently pull down on the access point and attempt to rotate it from side to side. If the access point comes off the bracket, relock the device onto the bracket as described in step 11 on page 34. 13 If the MP requires an external antenna, install and connect the antenna. (See “Connecting an MP to an External Antenna” on page 49.
Installing an MP-422 Chapter 3 Junction Box Installation (For required mounting hardware and tools, see Table 4 on page 22.) 1 Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point as shown in Figure 22. Caution! To avoid damage to the MP access point’s lock mechanism or electronic components, do not use excessive force when inserting a tool into the Unlock or Lock hole. 840-9502-0011 Figure 22.
Installing an MP-422 Chapter 3 840-9502-0008 Figure 23. Step 2—Removing the Bracket 3 Attach the universal mounting bracket to the junction box as shown in Figure 24: a Place the universal mounting bracket against the junction box so that the two screw holes face the junction box and align over the screw holes in the box. b Insert the #6-32 x 1-inch machine screws in the universal mounting bracket’s screw holes, and use a #2 Phillips-head screwdriver to tighten them.
Installing an MP-422 Chapter 3 Figure 24. Step 3—Placing the Bracket on the Junction Box Junction box 840-9502-0017 Port connector opening 4 Pull the Cat 5 cable(s) about 15 cm (about 6 inches) out of the junction box and through the port connector opening to create enough slack to insert the cable(s) into the port connectors. 5 Insert the Cat 5 cable(s) into the connector(s): 6 38 ● For a single connection, use the connector for port 1. ● For redundancy, insert one cable into each connector.
Installing an MP-422 Chapter 3 7 Lift the MP access point into place on the universal mounting bracket. Make sure the cable feeds properly into the junction box as you lift the device, and does not become trapped between the access point and the bracket. 8 Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point as shown in Figure 25.
Installing an MP-422 Chapter 3 Solid Wall or Ceiling Installation Note. The solid surface mounting option requires Cat 5 cable that does not have strain relief, unless you plan to route the cable through a hole in the wall or ceiling. The other options can use Cat 5 cable with or without strain relief. (For required mounting hardware and tools, see Table 4 on page 22.
Installing an MP-422 Chapter 3 3 Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point as shown in Figure 26. Caution! To avoid damage to the MP access point’s lock mechanism or electronic components, do not use excessive force when inserting a tool into the Unlock or Lock hole. 840-9502-0011 Figure 26. Step 3—Unlocking the Bracket 4 Remove the bracket as shown in Figure 27. 840-9502-0008 Figure 27.
Installing an MP-422 Chapter 3 5 As shown in Figure 28, feed the Cat 5 cable(s) through the port connector opening and align the universal mounting bracket over the drywall anchors so that the two screw holes in the bracket face the drywall anchors. 6 Insert the #6 sheet metal screws into the screw holes, and tighten them to secure the universal mounting bracket to the wall or ceiling. (If you routed the Cat 5 cable through a hole in the wall or ceiling, insert the screw into the center screw hole only.
Installing an MP-422 Chapter 3 7 8 9 Insert the Cat 5 cable(s) into the connector(s): ● For a single connection, use the connector for port 1. ● For redundancy, insert one cable into each connector. Install the Kensington lock, if you plan to use one. a Loop the Kensington lock’s cable around an object that cannot be moved or damaged by a person pulling on the cable. b Insert the key into the Kensington lock. c Insert the Kensington lock into the security slot on the MP.
Installing an MP-422 Chapter 3 10 Lock the MP access point onto the bracket by inserting the 3-mm or 1/8-inch screwdriver into the Lock hole on the access point as shown in Figure 30. Caution! To prevent possible damage to the MP access point, make sure the device is fully locked onto the bracket before letting go of it. Lock 11 840-9502-0062 Figure 30.
Installing an MP-422 Chapter 3 Tabletop Installation (For required mounting hardware and tools, see Table 4 on page 22.) 1 Reverse the universal mounting bracket: a Unlock the universal mounting bracket from the MP access point by inserting the 3-mm or 1/8-inch screwdriver into the Unlock hole on the MP access point as shown in Figure 31.
Installing an MP-422 Chapter 3 b Remove the bracket as shown in Figure 32. 840-9502-0008 Figure 32. Step 1b—Removing the Bracket c Turn over the universal mounting bracket, then align the bracket over the cable ports and the four mounting posts as shown in Figure 33. 840-9502-0061 Figure 33.
Installing an MP-422 Chapter 3 840-9502-0062 Figure 34. Step 1d—Locking the Bracket Lock 2 Attach the three rubber adhesive feet onto the universal mounting bracket, in the three location circles, as shown in Figure 35. 840-9502-0013 Figure 35. Step 2—Installing the Rubber Feet 3 Insert the Cat 5 cable(s) into the connector(s): ● For a single connection, use the connector for port 1. ● For redundancy, insert one cable into each connector.
Installing an MP-422 Chapter 3 4 48 Install the Kensington lock, if you plan to use one. a Loop the Kensington lock’s cable around an object that cannot be moved or damaged by a person pulling on the cable. b Insert the key into the Kensington lock. c Insert the Kensington lock into the security slot on the MP. d Rotate the key right or left to secure the lock to the MP. e Pull on the lock to verify that it is secured to the MP. f Remove the key.
Installing an MP-422 Chapter 3 Connecting an MP to an External Antenna Each radio in an MP-422 can use an optional Trapeze external antenna. To mount the antenna, see the instructions that come with the antenna. Caution! The external antenna must be installed at least 20 cm from the MP access point. To connect a mounted external antenna to an MP-422: 1 Attach the exterior antenna cable that is shipped with the antenna to the MP external antenna connector.
Connecting an MP to an MX Switch Chapter 3 Connecting an MP to an MX Switch You can connect an MP access point directly to an MX switch or indirectly to the switch through an intermediate Layer 2 or Layer 3 network. If you are connecting the MP directly to an MX switch, use the following procedure to insert the cable into the MX switch and verify the link. You can use the CLI or RingMaster to configure an MP connection.
Verifying MP Health Chapter 3 1 Insert a Cat 5 cable with a standard RJ-45 connector as shown in Figure 36. For connection to an MP access point, use a straight-through cable. 2 When the link is activated, observe the MP LED for the port on the MX switch: MP LED Appearance Meaning Solid green For an MP access point’s active link, all the following are true: • MP access point has booted. • MP access point has received a valid configuration from the MX switch.
Verifying MP Health Chapter 3 52 ● If the LED is green and glowing steadily, the MP has been booted successfully by the MX switch and is ready for operation. ● If the LED is not steadily glowing green, contact the system administrator for the MX switch or, if you are the system administrator, see Appendix A, “MP Troubleshooting,” on page 53.
A MP Troubleshooting After you insert a Cat 5 cable into an MP access point’s port connector and enable PoE on the cable, observe the device’s health or LINK LED to determine the status of the connection with the MX switch. ● If the LED is green and is glowing steadily, the MP has been booted successfully by the MX switch and is ready for operation. ● If the LED is not steadily glowing green, see Table 5. (For descriptions of all the LEDs, see “Status LEDs” on page 12.) Table 5.
Appendix A Table 5. Health LED States (continued) Health or LINK LED Appearance Diagnosis Remedy Slowly alternating green and amber MP access point is booting Wait a few seconds for the boot with an image received from process to complete. If this LED an MX switch. appearance persists, enable a radio or place a radio in sentry mode. Solid amber MP access point is waiting to receive boot instructions and a configuration file from an MX switch. 54 Wait a few seconds for the boot process to begin.
B MP Technical Specifications This appendix lists the technical specifications for the Trapeze Networks MP-422 access point. Table 6 lists the mechanical and compliance specifications. (For detailed compliance information, see the Trapeze Regulatory Information document.) Table 7, Table 8, and Table 9 list the radio specifications. Table 10 lists the MAC address allocation scheme. (For specifications for the MX switch, see the Trapeze Mobility Exchange Installation and Basic Configuration Guide.) Note.
Appendix B Table 6. MP Mechanical and Compliance Specifications Specification Description Size Diameter: 16.76 cm (6.6 inches) Height: 6.1 cm (2.4 inches) Weight Without mounting bracket: 0.45 kg (16 ounces) With mounting bracket: 0.5 kg (17.5 ounces) Operating Temperature 0° C to +50° C (32° F to 122° F) Storage Temperature -20° C to +70° C (-4° F to +158° F) Humidity 10% to 95% noncondensing Power over Ethernet (PoE) 42 VDC to 57 VDC (46 VDC nominal) IEEE 802.
Appendix B Table 6. MP Mechanical and Compliance Specifications (continued) Specification Description Encryption Wi-Fi Protected Access (WPA) Advanced Encryption Standard (AES) 40-bit/104-bit Wired-Equivalent Privacy (WEP) General Power-save mode supported Transmit power control in 1 dBm increments Supports up to 250 clients per radio Table 7. 802.
Appendix B Table 8. 802.11b Radio Specifications Specification Description Antenna type Integrated diversity omnidirectional External sectorized or directional (optional) Antenna gain Internal: 3 dBi External: • ANT-1060—greater than 10 dBi • ANT-1120—7 dBi or more • ANT-1180—6 dBi or more • ANT-7360—6 dBi • ANT-7360-OUT—6 dBi Frequency band 2.4 GHz to 2.
Appendix B Table 9. 802.11g Radio Specifications (continued) Specification Description Frequency band 2.4 GHz to 2.
Appendix B Table 10. MAC Address Allocations on MP-422 MP base MAC Address • The MP has a base MAC address. All the other addresses are assigned based on this address. Ethernet Port MAC Addresses • Ethernet port 1 equals the MP base MAC address. • Ethernet port 2 equals the MP base MAC address + 1. 802.11a Radio and SSID MAC Addresses • The 802.11a radio equals the MP base MAC address + 1. • The BSSIDs for the SSIDs configured on the 802.11a radio end in odd numbers.
Index A D access point.
troubleshooting with 53 verifying MP health with 51 I installation junction box 36 MP 15, 22 requirements 18 requirements, tools 22 solid surface 40 suspended ceilings 30 suspended ceilings, flush tiles 24 tabletop 45 T-bar ceilings.
RingMaster wall installation recommendations 19 work order 18 RJ-45s 9 radio 19 work order, RingMaster 18 S safety notices, explanations of 4 solid surface installation 40 specifications 55 status LEDs. See LEDs status lights. See LEDs suspended ceilings, installation drop tiles 30 flush tiles 24 switch. See MX (Mobility Exchange) syntax conventions 5 T tabletop installation 45 TAC (Technical Assistance Center) iii T-bar ceilings.
64 Trapeze Mobility Point Installation Guide
Trapeze Regulatory Information Hardware Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety and Advisory Notice Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Regulatory Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Declarations of Conformity . . . . . . . . . . . .
Safety and Advisory Notice Conventions Direct current (DC). Alternating current (AC). Complies with Underwriters Laboratories regulations in United States and Canada. Complies with European Union (CE) regulations. Contains a radio transmitter that complies with the Radio and Telecommunications Technical Equipment (R&TTE) Directive 1995/5/EC to an unharmonized frequency spectrum.
Regulatory Compliance Information Regulatory Compliance Information Trapeze Networks products cause no electromagnetic interference to other devices if installed and operated properly and without modification. Modification Prohibition Caution! The Part 15 radio device in the access point operates on a noninterference basis with other devices operating at the same frequency. Any modification to this device not expressly approved by Trapeze Networks can void your authority to operate the device.
Regulatory Compliance Information This accepted equipment is designed and tested to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed in accordance with the instruction manual, may cause harmful interference. There is no guarantee that interference will not occur.
Regulatory Compliance Information conditions: l This device may not cause harmful interference. l This device must accept any interference received, including interference that may cause undesired operation. The device is certified to the requirements of IC RSS-139-1. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system. For more information, contact your local Industry Canada office.
Regulatory Compliance Information Translation: This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
Regulatory Compliance Information Lithium Battery Caution The MX switch contains a lithium battery. If you need to replace the battery, make sure you dispose of the battery properly according to local regulations and replace the battery only with another comparable lithium battery. Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Attentie! Gevaar voor explosie als accu wordt vervangen door onjuist type.
Declarations of Conformity Declarations of Conformity The following sections contain declarations of conformity. European Union Notice All products labeled with the CE marking comply with the Electromagnetic Compliance (EMC) Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (ENs). The equivalent international standards are listed in parentheses.
Declarations of Conformity European Community, Switzerland, Norway, Iceland, and Liechtenstein Declarations Table 1 lists European declarations of conformity with Radio Equipment and Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Table 1. European Declarations of Conformity with R&TTE Directive 1999/5/EC Language Declaration Statement English This equipment complies with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Translations of Warnings and Warning Conventions Translations of Warnings and Warning Conventions Warning Conventions Warning! This situation or condition can cause injury. Waarschuwing! Warnung! Diese Situation oder dieser Zustand kann zu Verletzungen führen. Avertissement ! Aviso Deze situatie of omstandigheid kan letsel veroorzaken. Cette situation ou cette condition peuvent provoquer des blessures. Esta situación o condición puede causar lesiones. Warning! High voltage.
Translations of Warnings and Warning Conventions Warning! Radiation. This situation or condition can cause injury due to improper handling of fiber-optic equipment. Waarschuwing! Straling. Deze situatie of omstandigheid kan letsel veroorzaken door onjuist gebruik van glasvezelapparatuur. Warnung! Strahlung. Diese Situation oder dieser Zustand kann durch falschen Umgang mit glasfaserbasierten Geräten zu Verletzungen führen. Avertissement ! Radiation.
Translations of Warnings and Warning Conventions Radio Safety Warnings Warning! Do not operate the MP access point near unshielded blasting caps or in an otherwise explosive environment unless the device has been modified for such use by qualified personnel. Waarschuwing! Het MP-toegangspunt mag niet worden gebruikt in de nabijheid van onafgeschermde slaghoedjes of in een andere explosieve omgeving tenzij het apparaat voor een dergelijk gebruik is aangepast door bevoegd personeel.
Translations of Warnings and Warning Conventions Warning! Do not hold any radio device so that the antenna is very close to or touching the face, eyes, or other exposed body part while the device's radio antenna is transmitting. Waarschuwing! De antenne van een apparaat dat radiogolven aan het uitzenden is, mag nooit vlakbij of tegen het gezicht, de ogen of een andere onbedekt deel van het lichaam worden gehouden.
Translations of Warnings and Warning Conventions Lightning Warning Warning! Do not connect or disconnect cables or otherwise work with the MP access point hardware during periods of lightning activity. Waarschuwing! Tijdens onweer met bliksem mogen kabels nooit worden aangekoppeld aan of losgekoppeld van het MP-toegangspunt of andere werkzaamheden aan het MP-toegangspunt worden verricht.
Translations of Warnings and Warning Conventions Earth Ground Warning Warning! Earth grounding is required for an MX switch installed in a rack. If you are relying on the rack to provide ground, the rack itself must be grounded with a ground strap to the earth ground. Metal screws attaching the switch to the rack provide ground attachment to the rack. Waarschuwing! Aarding aan de grond is vereist voor een MX switch geïnstalleerd in een rek.
Translations of Warnings and Warning Conventions Rack Installation Warnings Warning! Trapeze Networks recommends that you ask someone to assist you with the remaining steps. If you accidentally drop the MX switch, you can be injured and the switch can be damaged. Waarschuwing! Trapeze Networks adviseert dat u bij het uitvoeren van de resterende stappen iemand ter assistentie vraagt. Als u de MX switch per ongeluk laat vallen, kunt u letsel oplopen en kan de switch beschadigd raken.
Translations of Warnings and Warning Conventions Overcurrent Warning Warning! The MX switch relies on the building’s installation for overcurrent protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10 A international) is used on the phase conductors. Waarschuwing! De MX switch is afhankelijk van de in het gebouw geïnstalleerde beveiliging tegen overstroom. Op de fase-aders dient een zekering of circuitonderbreker te worden gebruikt van maximaal 240 V~, 10 A.
