User Guide 10ft x 18ft Rectangle Trampoline and Enclosure Model: JKRC1018HEC3 The trampoline / enclosure is designed for users weighing 181kg (400lbs) or less. Got a Problem building your trampoline? Please contact us at contact@jumpking.com WARNING: Read these assembly instructions carefully before attempting to assemble or use this product. Keep this user guide in a safe place for future reference.
10ft x 18ft Rectangle Trampoline and Enclosure Model: JKRC1018HEC3 If you have questions after reading this manual, please email us at contact@jumpking.com. Trained technicians will provide immediate assistance. IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 WARNING LABEL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 TRAMPOLINE / ENCLOSURE SAFETY INFORMATION . .
MAX 181 kg (400 lbs)
1. Trained Spo er supervision is recommended. 2. Must place the trampoline on lawn, bark wood chip, sand or cushioning materials. 3. Maintain a free space of minimum 8.2� on all sides of the trampoline. This area should not included concrete, bitumen, brick or other hard surfaces as these can cause serious injuries. 4. Adequate overhead clearance is essen al. A minimum of 24 from ground level is recommended. Provide clearance for wires, tree limbs and other possible hazards. 5.
24. Learn fundamental bounces and body posi ons thoroughly before trying more advanced skills. A variety of trampoline ac vi es can be carried out by performing the basic fundamentals in various series and combina ons, performing one fundamental a er another, with or without feet bounces between them. 25. Avoid bouncing too high. Stay low un l bounce control and repeated landing in the center of the trampoline can be accomplished. Control is more important than height. 26.
WARNING Do not attempt or allow somersaults. Serious injuries, paralysis, or death may result. Do not allow more than one person on the trampoline at a time. To reduce the chance of landing on your head or neck, do not do somersaults(flips). Use trampoline only with mature, knowledgeable supervision. Not recommended for children under 6 years of age. Read instructions before use. Inspect before use and replace any worn, defective or missing parts. Avoid bouncing when tired.
Thank you for selecting a Jumpking trampoline / enclosure. “Jumpking” is designed and crafted to provide many years of fun and fitness. This trampoline / enclosure comes equipped with warnings and instructions for the assembly, care, maintenance and use of the trampoline / enclosure. This information must be read by all trampoline supervisors and users before any person is allowed to use the trampoline / enclosure. If you have questions after reading this manual, please visit our websites at www.jumpking.
181 70 400
BUILDING YOUR TRAMPOLINE 1. This is a 2 person build. 2. Time for build is approximately 2 hours. 3. Choose a good location: (wood chippings, sand or grass). wires, trees and other possible hazards. (7.3m) from ground level, away from (2.5m) around sides, away from walls, fences, structures, roads and other hard surfaces and play areas.
PARTS LIST Part 1 Leg side corner Part#LSC101618HE Part 2 Leg side middle Part#LSM101618HE Quantity: 8 Quantity: 4 Part 7 Part 8 T-connector With welded tube T-connector With 2 welded tube Part 3 Leg center corner Part#LCC101618HE Quantity: 4 Part 9 Support connector Part#TCWS101618HE Part#TCW2S101618HE Quantity: 8 Quantity: 4 Quantity: 8 Part 14 Part 15 Part 13 Top tube D Top tube B Part#TRB1018HE Part#TRD1018HE Quantity: 2 Quantity: 4 Part 19 8.5 inch Spring Part#SP8.
A E F Support Connector Support Connector A x2 E F Support Connector Support Connector x2 17
Marked A x4 Marked F x4 Support Connector x8 18 Marked E x4
A Support Connector F E x2 E Support Connector F A x2 19
E F A C B E D F B A A B F D E B C A E F 27
A E F E A F 28 x2 x2
Turn over the Center Support Section. Top Tube B will be inserted into T-connectors with 2 welded tubes.
Turn over 2 corner sections then insert each end of Top Tube A into T-connector w/ 1 welded tube on Top tube B.
Then insert one end of both remaining Top Tubes B into the other T-connector w/ 2 welded tubes.
Next turn over remaining 2 corner sections. Insert each end of Top Tube B into T-connector w/ 1 welded tube. Note: Please keep Top tube C insert into top tube E later after jumping bed attached.
x116 (8.5” length) x8 (5.
Lay the stitched bed (with the V-rings) out inside the frame of the trampoline with the warning labels facing upwards.
5.5” length spring 2 Then take 4 of the 5.5" springs and use the spring pulling tool to insert one end into trampoline frame after connecting the other end to the V-ring. Place in the 1st corner than go to the next corner and repeat this step.
Then with the remaining each on of 5.5" springs on each corners, repeat previous step going clockwise.
Take the remaining Top Tube C and insert each end into T-connector w/ 1 welded tube. Now your frame is assembled.
Then with the remaining 4 5.5" springs, repeat previous step going clockwise. 5.
8.5” length spring Top spring holes Next you will use 16 8.5" springs and place 4 into top spring holes in the frame in position 1, then 2 (diagonally across), then 3 & finally 4 (diagonally across).
8.5” length spring Top spring holes Next you will use 16 8.5" springs and place them in the center top holes on the short sides with 8 each in positions 1 & 2.
Top spring holes Ste p1 St ep 2– 42 11 TO P Sp rin gs 8.5 ” –1 1T OP Sp rin gs 8.
Once finished, all Top Springs in the center of the trampoline should look like this. St ep St ep 4– 11 TO P Sp rin gs 3– 11 TO P Sp rin gs 8.5 ” 8.
8 Bottom spring holes St ep St ep 44 2– 10 BO TT OM Sp rin gs 8.5 ” 1– 10 BO TT OM Sp rin gs 8.
Bottom spring holes St ep St ep 4– 10 3– 10 BO TT OM Sp rin gs 8.5 ” BO TT OM Sp rin gs 8.
Lay one long side of the pad out over the edge of the frame with the ties facing downwards. Align the openings in the frame pad with the T-connector+welded tube’s on the frame.
Repeat previous step with the other long side of pad.
Lay one short side of the pad out over the edge of the frame with the ties facing downwards. Align the openings in the frame pad with the T-connector+welded tube’s on the frame.
Repeat previous step with the other short side of pad.
Look under the trampoline and locate the pairs of straps near the edge of bed near the frame. Tie each of these around the frame to secure the pad in place. Now your frame pad is installed.
Insert the thin end on one of the bottom enclosure tubes into the open end of one of top enclosure tubes. Align the hole in the bottom enclosure tube with the slot in the top enclosure tube. Use a Phillips head screwdriver to secure a self tapping screw in place. Repeat for all remaining poles.
Slide the foam sleeve up to cover where enclosure poles are connected. Repeat for all poles.
Insert all 12 assembled enclosure poles into T-connectors with welded tubes. Please make sure the pole completely inserted into T-connector+welded tube.
1 67 IMPORTANT: Make sure that all poles are all the way down.
2 Continue to do this until you have used up nearly all the cord then tie the end round a V-ring.
3 69
181kg 400 70
SPARE PARTS 18 26 12 15 5 16 11 6 9 4 13 14 10 18 17 22 1 3 21 9 Key No. 1 2 3 4 5 6 7 8 Qty. 8 4 4 4 2 4 8 4 9 10 11 12 8 2 12 12 71 2 7 8 Description L-Leg Center Support L-leg V-leg Top tube A Top tube C Corner tube F T-connector with welded tube T-connector with 2 welded tube Support Connector Center Support V-leg Bottom enclosure poles Top enclosure poles 24 25 Key No. 23 19 20 Qty.