Julius Blum GmbH Industriestrasse 1 6973 Hoechst Austria www.blum.com SERVO-DRIVE RF Module 23.A00L83 Manual 1.0.2 Edition 30.08.2019 Authors Rashid Talib, Arendi Armin R.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 2 of 17 History Date Author 30.08.2019 ELAR 28.08.2019 ELAR 22.08.2019 ELAR 04.05.2018 TALRA Changes Version 1.0.2 -- Regulatory Information for Canada und USA added Version 1.0.1 -- Regulatory Information for Taiwan added Version 1.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 3 of 17 Table of contents 1 Terms and definitions ........................................................................................................................ 4 2 References ........................................................................................................................................ 4 3 Specifications ..............................................................................................................................
Blum 23.A00L83 RF Module Manual 1.0.2 Page 4 of 17 1 Terms and definitions BLE Bluetooth Low Energy dBm Power level in decibel, relative to 1mW dBc Power level in decibel, relative to carrier DTM Direct Test Mode VNA Vector Network Analyzer PER Packet Error Rate SoC System on Chip 2 References [1] nRF52832 Datasheet v1.4: http://infocenter.nordicsemi.com/pdf/nRF52832_PS_v1.4.pdf 3 Specifications • 2.4 GHz transceiver • Supporting BLE 4 and shock burst protocols • 3.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 5 of 17 4 Overview The Module is a compact 2.4GHz RF Module supporting BLE 4 and shock burst protocols. The module is designed to add RF functionalities to applications with limited space and requires no additional components. The Module is certified and easy to use, no RF knowledge is required. 4.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 6 of 17 4.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 7 of 17 5 Mechanical 5.1 Dimensions Image 3 shows the dimensions of the module. Top View 15 9 (9 x 1mm) 7 (7 x 1mm) 1 Front View 6 (6 x 1mm) 1 2 3 4 5 6 7 GND VDD GND SW DIO GND SW CLK GND 2.5 9 (6 x 1.5mm) 10 DC GND GND Top-View GND 14 13 12 11 10 9 8 GND 2.7 x 2 3 5 Right View Image 3 Module dimensions 0.7 x 0.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 8 of 17 5.2 Pinout 1 2 3 4 5 6 7 GND VDD GND SW DIO GND SW CLK GND DC GND GND Top-View GND 14 13 12 11 10 9 8 GND Image 4 Pinout Pin Function Type Remarks 1 P0.00 Digital I/O General purpose I/O Analog input 32kHz crystal input1 (LFXO) Digital I/O General purpose I/O XL1 2 P0.01 XL2 3 4 5 6 P0.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 9 of 17 11 P0.07 12 P0.08 13 14 Digital I/O General purpose I/O Digital I/O General purpose I/O NFC1 NFC input NFC antenna connection1 P0.09 Digital I/O General purpose I/O NFC2 NFC input NFC antenna connection1 P0.10 Digital I/O General purpose I/O GND GND VDD VDD DCC DCC SWDIO SWDIO WKUP GND Power Power VDD Power SWDCLK SWDCLK 1 Supply Pad DC/DC regulator output.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 10 of 17 5.3 Recommended PCB dimensions PCB keep red area free from copper and traces 15 9 (9 x 1mm) 7 (7 x 1mm) 1 6 (6 x 1mm) 1 2 3 4 5 6 7 GND VDD GND SW DIO GND SW CLK GND 2.5 9 (6 x 1.5mm) 10 min 20 DC GND GND Top-View GND 14 13 12 11 10 9 8 GND 2.7 x 2 3 5 0.7 x 0.7 All dimensions in mm (not to be scaled) min 20 Image 5 Recommended PCB dimensions 3.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 11 of 17 6 Regulatory Approval The module has received regulatory approval for the following countries: • United States / FCC ID: W95-23A00L83 • Canada / ISED ID: 8352A-23A00L83 HVIN: 23.A00L83 • Europe/CE • Taiwan The integrated trace antenna of the module is of an optimized design an must not be modified. Host-design must strongly follow the recommendation found in chapter 5.3. The shielding is an integral part of the module. 6.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 12 of 17 transmission sub-assembly, designed to be incorporated into another device, that must demonstrate compliance with FCC rules and policies independent of any host.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 13 of 17 A user’s manual for the product must include the following statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 14 of 17 co-located or operating in conjunction with any other antenna or transmitters within a host device, except in accordance with FCC multi-transmitter product procedures. The installation of the transmitter must ensure that the antenna has a separation distance of at least 30 mm from all persons or compliance, and it must be demonstrated according to the FCC SAR procedures. 6.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 15 of 17 This device complies with Industry Canada’s license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 16 of 17 Note: To maintain conformance, the module shall be installed in accordance with the installation instructions in this data sheet and shall not be modified. When integrating a radio module into a completed product the integrator becomes the manufacturer of the final product and is therefore responsible for demonstrating compliance of the final product with the essential requirements against the RED. 6.4.
Blum 23.A00L83 RF Module Manual 1.0.2 Page 17 of 17 When the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module NCC ID: CCXXxxLPyyyZzW” or “Contains NCC ID: CCXXxxLPyyyZzW” or any similar wording that expresses the same meaning may be used.
