Network Camera Installation and Operating Instructions Version 1.0 Model: APPCAM23 These instructions should be retained in a safe place for future reference.
CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. INTRODUCTION ..............................................................................2 PLEASE READ BEFORE YOU START ........................................2 WIRELESS DEVICES OPERATING RANGE..............................2 IMPORTANT SAFETY PRECAUTIONS .......................................2 KIT CONTENT ..................................................................................4 SAFETY AND INSTALLATION TIPS ............................................
1. INTRODUCTION The WIP APP Camera is a wireless security system designed for easily creating your home security network. Downloading the free App, you can view and capture video clips of any motion detected by the wireless camera(s) and store them onto the memory card via smart phones and/or tablets running iOS/Android. Snapshot function captures images and stored them directly to smart phones and/or tablets.
(10) Check power cables, do not get crushed or damaged by sharp edges whenever the devices are in operation. FCC Compliance Statement: This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2. KIT CONTENT A App Camera x 1 C Camera Antenna x 1 E Ethernet Cable x 1 G Manual x 1 B Camera Stand x 1 D 5V/1A Power Adapter for Camera F Screw Bag x 1 Tools Required: Electric drill 5mm masonry drill bit 15mm masonry drill bit No.
3. SAFETY AND INSTALLATION TIPS Do not attempt to open the units with the power adaptor plug connected to avoid any risk of personal injury. When installing CCTV camera(s), always follow manufacturer's advice when using power tools, steps, ladders, etc. and wear suitable protective equipment (e.g. safety goggles) when drilling holes. Before drilling holes through walls, check for hidden electricity cables and water pipes. The use of cable/pipe detector is advisable.
Planning your layout Night Vision The camera has built-in infra-red LEDs to allow you to view at night for 24hrs surveillance. The LEDs will automatically activate at night and the picture viewed will turn to black and white. The night viewing range is up to 5 meters.
Camera Installation A. Secure camera stand on the wall B. Loosen up the Thumb screw C. Adjust proper view angle then secure the joint with T-bolt.
Connection Diagram 8
4.
5. DOWNLOAD AND USE THE APP The WAPP CAM is designed to remotely view the live camera video with your smart phone or tablet device. Please follow these steps to download, setup and use the App. Download the App 1. From you Android smart phone or tablet device, click the Android Market. 2. Tap on the search icon and type in “APPCAM.” The icon appears as a square with an orange emblem. 3. Click on the App to choose and click the download button. 4.
field. 7. Enter the default password 123456 in the PASSWORD field. “Enable Email Alert” option will send an email alert to your smart phone or tablet whenever the motion detection is triggered. “Enable Event Notify” option will notify you whenever any recording event is produced. Note: When you type in the default password, the system will alarm you to change it. Please follow the instruction of the DEVICE PASSWORD section to change the default password into your personal security code. (page 16) 8.
You can also use the SEARCH feature for a quick setup. This feature will automatically search for your camera(s) on your local area network (LAN). Please follow the steps below. 1. Connect your smart phone or tablet device to WiFi which the camera is used. 2. Click SEARCH button in the App. The system will automatically find the available camera on the local area network (LAN) and carry out the DID code in the DID field. You only need to enter the default password 123456. 3.
Once the camera is connected, the App will show the video as below. You can tap the icons to add more cameras or configure the advanced settings. Tap to add more camera(s). Tap to setup the camera configuration. Tap to update the status of camera(s). Tap to enable PIN lock or enter the INFORMATION page. The ADD CAMERA icon allows you to add more cameras. The systems supports up to 4 concurrent cameras. Tap the ADD CAMERA icon and follow the steps of App setup to add more cameras.
The INFORMATION icon allows you to enable PIN lock or check the App information. Setup PIN Lock If you enable PIN Lock, the user will be asked to enter the PIN code when you turn on your mobile device. 1. Click the “Enable lock when starting” then type in your PIN code. 2. Confirm your PIN code again. About Tap the ABOUT icon to check the WIP and API Kernel version information.
App Operation When you launch the App on the smart phone or tablet, the image displayed on the main screen is the latest captured camera image from previously established session. The App then updates the status of all cameras automatically. You can take a snapshot or record a video clip with the icons below. Tap the SNAPSHOT icon to capture screen images. Tap the MUTE icon to turn on/off the volume when playback the video. Tap the RECORD icon to record and tap again to stop recording.
Advanced Setting The Advanced setting allow you to setup the time zone, device password, video setting, WiFi setting, sensitivity setting, and email setting. You can also format the SD card or check the device information here. Tap the CAMERA SETTING icon on the panel. . The following icons appear Tap the ADVANCED SETTING icon to setup camera configuration. Press to enter the advanced settings Tap the DELETE icon to remove current camera. Tap the EVENT LIST icon to check the recorded events.
Admin Password The Admin Password is a specific security code for your advanced settings. The default password is 123456. Please use this function to change the default password into your personal admin password. For the protection of your system configuration, every time you change the advanced settings, you need to enter the admin password. Time Zone The drop-down list shows the world time zone. Select the time zone that will work the best for you.
Video Setting The video setting section allows you to configure the video quality and environment mode. Video Quality Set up the video format to VGA/QVGA with High/Low resolution. Environment Mode Choose the appropriate option in accordance with local power frequency. WiFi Setting The WiFi setting allows you to choose the WiFi connection that you wish to use and setup the WiFi environment.
Sensitivity Setting Set up the sensitivity of motion sensor from OFF, LOW to HIGH. If you set OFF the sensitivity setting, the system will turn off the motion detection function. If you configure the sensitivity setting into LOW or HIGH, the system will start recording when any movement occurs within the viewing angle of the camera. Please adjust the setting to acquire the expected motion detection. Email Setting The email setting allows you to configure the email environment, email account and password.
Device Information This section contains the model number, device version, vendor name, total size and available size of the memory card.
6. TROUBLE SHOOTING IF… SOLUTION No image appears Make sure the power adaptor is not damaged or defective and plugged into an electrical outlet with power. Relocate the camera to obtain the best reception of wireless signals. Make sure the camera is properly configured in App. Low wireless signal Wireless devices such as wireless home stereo system may reduce the signal strength. Leave as much space as possible between the camera/mobile device and these wireless devices.
Bright white spots appear at night time The camera's infrared LEDs produce invisible light that reflects off surfaces such as glass. Install the camera on the other side of windows or place the lens flush against the surface to improve the night vision. It is suggested to install camera(s) under well lit area. Note: Please check the environment rating (Ingress) of the camera(s) before installing outdoors. Memory card error Make sure the memory card is correctly inserted and formatted.
7. ABOUT DIGITAL WIRELESS TECHNOLOGY This section offers some helpful information to overcome most of the problems you may encounter. We hope this section can help you to enjoy a pleasant setup. About 2.4GHz Digital Wireless Signal This innovative digital wireless solution integrates advance Frequency Hopping Spread spectrum (FHSS) technology. This technology greatly reduce the interference that comes from other devices using the same radio frequency (2.4GHz), e.g.
8. PRODUCTION SPECIFICATION Networking Parameter Wireless Technology IEEE 802.
Operating Temperature -10°~+50°C 9.