USER GUIDE LoRa® SPY Ref : 11819G
TABLE OF CONTENTS I. INTRODUCTION ........................................................................................................................................ 3 a) Product contents ....................................................................................................................................................... 3 b) Symbols ......................................................................................................................................................
I. INTRODUCTION The LoRa® SPY is a recorder capable of measuring 1 or 2 physical quantities (T / TH or other quantity depending on the model) and transmitting by radio to monitoring software hosted on a platform. The radio transmission uses the LoRa® long-distance network. The LoRa® SPY (T0, T1 andT2) comply with EN 12830 and compatible with EN 13486 which defines procedures for periodic verification.
The thickness of an obstacle in the wave path. The attenuation is greater diagonally than perpendicularly A solid metal wall will not allow transmission by radio. A perforated metal wall will allow waves to pass while attenuating them. b) Positioning The LoRa® SPY units can be placed either inside or outside the enclosures. For installations outside the enclosure, mount the units sufficiently high on the walls to avoid interference with obstacles and foot traffic.
b) LCD display Battery level indicator MySirius connection indicator LoRa® networkconnection indicator Searching factory network blinking : Searching for LoRa® network Fixed : LoRa® network found Empty: LoRa® Network not found Connected to MySirius RSSI radio reception level indicator Threshold overrun indicator ( c) High, Low) Mounting The LoRa® SPY can be mounted in 2 different ways Using a tie wrap to attach it to the monitored product Magnetically The LoRa® SPY has 3 internal magnets for mou
Once activated, the LoRa® SPY measures and transmits its measurements to My Sirius, at the frequency defined in MySirius, then flashes regularly as a function of its status. c) Turning Off 3’’ d) Actions on the touch-sensitive button Touch duration < 3s Mode Activation > 3s - during 3s 1s = OK 1s = Technical alarm 3x1s = OK but paused 1s = In alarm state Measurement Off >8s - Off during 3s The LoRa SPY remains activated Off V.
VI. BATTERY REPLACEMENT Removing the battery Open the battery cover with a suitable object (2cts coin) to align the marks (/!\0 = Open ; 1= Closed) Remove the battery from its lodging Replacing the battery Put the new battery in place respecting the polarity KEEP THE BATTERY AWAY FROM FIRE; DO NOT ATTEMPT TO RECHARGE OR SHORT-CIRCUIT IT ONLY USE BATTERIES* SUPPLIED BY JRI (REF : 11596) *Recommended battery: Saft LS14500 type AA 3.6V 2250mAh VII.
LoRa® SPY TH1 - Thermo-Hygro Internal HIM Communication Memory Sensor Operating range Measurement range Accuracy, standard version Temperature Humidity at T° between 15 and 25°C Resolution IP rating Frequency of recording and transmission Frequency of measurement Response time Power source : 1 RGB LED + 1 touch-sensitive button + 1 LCD display : LoRa® 868MHz or 915MHz* : 10 000 time-stamped measurements : Inside control unit : -30+70°C : -30+70°C and 0 – 100% RH : ± 0.4°C from -20 C° to +40°C / ± 0.
Frequency of measurement : 1 or 5min Response time Power source Case : ~ 2 min.
LoRa® SPY T4 Hygitherm (Calibrated for Hot Water Network) HIM : 1 RGB LED + 1 touch-sensitive button + 1 LCD display Communication : LoRa® 868MHz or 915MHz Memory : 10 000 time-stamped measurements Sensor (with overmoulded support) : PT100 non disconnectable Operating range : -30 to +70°C Measurement range Accuracy @55°C : -40 to +85°C : ±0.3°C on copper tube network ±0.5°C on HTA tube network Resolution : 0.
*2018 4th trimestrial. a) Compliance All our products are in compliance with the following standards: EN 12830 CE ERM VIII. Yes for T0, T1 and T2 models: these devices must be verified regularly according to EN 13486 (recommendation is once per year) EN 301 489 / EN 61000 / EN 61010 / EN 55022 / EN 300 220 MAINTENANCE Clean the device with a soft cloth, either dry or slightly moistened with water. To remove stubborn dust, use a cloth soaked in a diluted, non-abrasive detergent.
IX.
©JRI 13
©JRI 14
©JRI 15
X. GUARANTEE Our material is guaranteed for one year, parts and labor, against any manufacturing defect, functional failure or abnormal wear. This guarantee covers only the replacement of parts recognized to be defective as well as the repair of the material in question returned shipping paid to our workshops, and excludes all damages and interest or incidental expenses. The starting point of the guarantee is the date of invoice of the concerned product.
