User's Manual

ManualsBrandsJOYMAX ELECTRONICS ManualsElectronics2.4GHz ZigBee Wireless Module

TIGO MD102AD User Manual

V1.01

Benefits

 Microminiature module solutions

 Ready to use in products

 Minimizes product development time

 No RF test required for systems

 Compliant with FCC part 15 rules, IC Canada

Features: Module

 2.4GHz IEEE802.15.4 & ZigBee

PRO Compatible

 2.3-3.6V for SOC

 Sleep Current ( with Active Sleep

Timer ) 2.6µA

 Receiver Sensitivity -95dBm

 TX Power +2dBm

 TX Current 15mA

 RX Current 17.5mA

 Dimension：32.2*18*3.5mm

 Weight：3.0g

Features: Microcontroller

 32-Bit RISC CPU,up to 32MIPs

with low power

 128KB RAM, 128KB ROM

 4Mbit serial flash for program

code and data

 On chip OTP efuse

 JTAG debug interface

 4-input 12-bit ADC, 2 12-Bit

DACs, 2 Comparators

 3 Application Timer / Counters,

3 System Timers

 2 UARTs (One for In-System

Debug)

 SPI Port with 5 Selects

 2-Wire Serial Interface

 4-wire digtal audio interface

 Watchdog timer

 21 GPIO

Temperature Range

-40°C to +85°C

Humidity

10 to 95% RH

Lead-Free and RoHS Com

liant

Features: Module

 2.4GHz IEEE802.15.4 & ZigBee

PRO Compatible

 2.3-3.6V for SOC

 Sleep Current ( with Active Sleep

Timer ) 2.6µA

 Receiver Sensitivity -95dBm

 PIFA Antenna Gain +3dBi

 TX Power +2dBm (without PIFA

Antenna )

 TX Current 15mA

 RX Current 17.5mA

 Dimension：30*18*3.5mm

 Weight：3.0g

Features: Microcontroller

 32-Bit RISC CPU,up to 32MIPs

with low power

 128KB RAM, 128KB ROM

 4Mbit serial flash for program code

and data

 On chip OTP efuse

 JTAG debug interface

 4-input 12-bit ADC, 2 12-Bit DACs,

2 Comparators

 3 Application Timer / Counters,

3 System Timers

 2 UARTs (One for In-System

Debug)

 SPI Port with 5 Selects

 2-Wire Serial Interface

 4-wire digtal audio interface

 Watchdog timer

 21 GPIO

Temperature Range:-40°C to +85°C

Humidity:10 to 95% RH

Lead-Free and RoHS Compliant

IEEE802.15.4 / ZigBee PIFA Module Family

Overview

This MD-102AD ZigBee PIFA Module is a surface mount module with 1mW output power that

enables users to implement IEEE802.15.4 or ZigBee PRO networking applications with

minimum time to market and at the lowest cost. They remove the need for expensive and

lengthy development of custom RF board designs and test suites. The modules provide a

comprehensive solution with high radio performance and all RF components included. All that

is required to develop and manufacture wireless control or sensing products is to connect a

power supply and peripherals such as switches, actuators and sensors, considerably

simplifying product development.

Applications

 Robust and secure low power wireless applications

 ZigBee PRO networks

 Home and commercial building automation

 Home networks

 Toys and gaming peripherals

 Industrial systems

 Telemetry and utilities

(e.g. AMR)

Summary of content (17 pages)

PAGE 1
TIGO MD102AD User Manual IEEE802.15.4 / ZigBee PIFA Module Family Overview This MD-102AD ZigBee PIFA Module is a surface mount module with 1mW output power that enables users to implement IEEE802.15.4 or ZigBee PRO networking applications with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules provide a comprehensive solution with high radio performance and all RF components included.
PAGE 2
TIGO MD102AD User Manual Revised History Date Revision Description 2011/08/17 1.0 1st Released Table of Contents 1. 2. 3. 4. 5. 6. Introduction .......................................................................................................... 3 1.1 Key Features ............................................................................................. 3 1.1.1 Module .............................................................................................. 3 1.1.2 Microcontroller ..
PAGE 3
TIGO MD102AD User Manual 1. Introduction This MD-102AD ZigBee PIFA Module is a surface mount module with 1mW output power that enables users to implement IEEE802.15.4 or ZigBee PRO networking applications with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules provide a comprehensive solution with high radio performance and all RF components included.
PAGE 4
TIGO MD102AD User Manual 2. Specifications VDD=3.0V @ +25°C Typical DC Characteristics Deep Sleep Current Sleep Current Radio Transmit Current Radio Receive Current 1.3uA 2.6uA 15mA 17.
PAGE 5
TIGO MD102AD User Manual 3. Pin Configurations Figure: MD-102AD Pin Configuration (Top View) 5 V1.
PAGE 6
TIGO MD102AD User Manual 3.
PAGE 7
TIGO MD102AD User Manual Pin Signal Function Alternative Function 26 VSSA Analogue ground 27 DIO12 DIO12, Timer1 capture (input), Antenna Diversity or Digital Audio Word Select TIM1_CAP ADO DAI_WS 28 DIO13 DIO13, Timer1 PWM (output), Antenna Diversity or Digital Audio Data Input TIM1_OUT ADE DAI_SDIN 29 RESETN Reset input 30 DIO14 DIO14, Serial Interface clock or Intelligent peripheral clock Input SIF_CLK IP_CLK 31 DIO15 DIO15, Serial Interface data or Intelligent peripheral
PAGE 8
TIGO MD102AD User Manual 4. Additional Information 4.1 Outline Drawing Figure: MD-102AD Outline Drawing 8 V1.
PAGE 9
TIGO MD102AD User Manual 4.2 Module PCB Footprint Figure: Module PCB footprint 9 V1.
PAGE 10
TIGO MD102AD User Manual 4.3 Ordering / Lable Information Logo Label Line 1：IC ID Number Label Line 2：FCC ID Number Label Line 3：Part Name Label Line 4：Lot Code YYWWNNNNNN (See Below) Logo Label Line 1：IC ID Number Label Line 2：FCC ID Number Label Line 3：Part Name Label Line 4：Lot Code YYWWNNNNNN (See Below) Identifier YY WW NNNNNN Description Year Week Serial Number Format 11 (Example) 33 (Example) 000001 (Example) Figure: Example MD-102AD Labeling for FCC Approved Modules 13mm 16mm 10 V1.
PAGE 11
TIGO MD102AD User Manual 4.4 Tape and Reel Information 4.4.1 Tape Orientation and dimensions All dimensions are in mm Module type A B MD-102AD 18.5 32.7 Tolerance ±0.1 ±0.1 W 44 ±0.3 F E 20.2 1.75 ±0.1 +0.1 P0 4.0 ±0.1 P1 2.0 ±0.1 P2 24.0 ±0.1 T 3.4 ±0.1 Cover Tape width (W) 37.5 ±0.1 4.4.2 Cover tape details Thickness (T) 0.
PAGE 12
TIGO MD102AD User Manual 4.4.3 Leader and Trailer 4.4.4 Reel Dimensions Module type: A B C N W (min) MD-102AD-5148A 330 ±1.0 2.2±0.5 13 ±0.2 100 +0.1 45.5±0.3 12 V1.
PAGE 13
TIGO MD102AD User Manual 4.5 SMT IR Profile Average ramp-up rate (217C to peak): 3 ℃ /sec. max. Preheat：150~200 ℃、60~180 seconds Temperature maintained above 217 oC : 60~150 seconds Time within 5 ℃ of actual peak temperature: 20 ~ 40 sec. Peak temperature：250+0/-5 ℃ Ramp-down rate : 6 ℃/sec. max. Time 25 ℃ to peak temperature : 8 minutes max. Cycle interval：5 minus 4.
PAGE 14
TIGO MD102AD User Manual 5. FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 15
TIGO MD102AD User Manual LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: XNNMD102AD ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules.
PAGE 16
TIGO MD102AD User Manual 6. IC Statement This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
PAGE 17
TIGO MD102AD User Manual 6.3 Avis de conformité insérés dans le manuel d'utilisation des appareils radio exempts de licence Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.