RA - 7203 VHF Receiver 1 DISPLAY 2 FbA (Function button A) 3 RS (Rotary switch) 4 SQUELCH LED 5 REMOTE LED 1 6 FRONT CONNECTOR 2 7 FbB (Function button B) 4 8 FbC (Function button C) 5 9 ON/OFF 10 ALARM LED 11 STANDBY LED 12 LOUDSPEAKER 3 6 7 8 9 10 11 12
RA - 7203 Front RJ45 connector Front Connector, RJ45 Name PIN Purpose SEL 1 TDO 2 Headset 3 RS232 4 RS232 Tx RS232 5 RS232 Rx TMS 6 +12VDC 7 +12 VDC to external equipment (10mA) GND 8 Common ground
RA - 7203 Technical data, 1 of 4 Standards; ICAO annex 10, EN300 676(AM, AM-MSK), EN301 841(VDL2 – Physical layer) Environmental: Temperature range -20°C to +55°C (operating) 40°C to +70°C (storage) Humidity 90% @+40°C (non condensing) Shock Transport: IEC-721-3-2, Class 2M3 Vibration Transport: IEC-68-2-32, Class 2M3. IEC-68-2-6 EMC EN 301 489 – part 22 Weight: 1.
RA - 7203 Technical data, 2 of 4 Frequency response: 300-3400 Hz 350-2500 Hz Data ports: RS232, RS485, 100/10BaseT Protocol: (SNMP v.2) Simple Network Management RS232/RS485 Jotron proprietary BITE monitoring: VSWR, Voltages, Currents, Levels, Lock detect, Temperature, Output power, Reflected power, a.o. Supply voltage: AC 115/230VAC +15/-10% / 50-60Hz Supply voltage, DC 21.6 - 31.
RA - 7203 Technical data, 3 of 4 Receiver Sensitivity analogue @1μV / 30% pd: Adjacent channel rejection: Intermodulation (3 signal): IF bandwidth: Image and IF frequency response: Squelch operation: Audio AGC: Noise blanker: Signal / Noise: AM 25kHz AM 8.33kHz 10dSINAD(CCITT) >70dB >60dB >70 dBc +/- 11kHz +/-2.
RA - 7203 Technical data, 4 of 4 AGC range: AGC attach time: AGC decay time: Inband squelch signal: Line output: -107dBm to +5dBm <50ms <200ms Configurable tones: 150-3400Hz 600Ω, -36 - +7dBm @90% modulation Harmonic distortion: <3% @90% AM (line output) Crossmodulation: >85dB @ 100 kHz frequency offset Blocking: >100dB @1MHz offset, >110 dB out of band signals Dynamic range: >110dB Spurious response rejection: >90dB
RA - 7203 Menus, 1 of 16 FbA FbC RS NOTE! RS can be pressed and turned. FbB The radio is controlled through an advanced menu system. The access for each menu is restricted by a user parameter. The System Operator can change all user parameters from SNMP, or from the menu using a hardware key.
RA - 7203 Menus, 2 of 16 There are four access user levels: User Name of menu: parameter: Access and restrictions: 1 System operator Full access to all parameters (R/W by System Operator) 2 Technician Access to some settings in RX menu system + bite (R/O) 3 Operators Access only to Volume, Frequency and memory store and recall 4 Restricted Restricted to Volume, Squelch and memory recall
RA - 7203 Menus, 3 of 16 When operated locally, the operator has full access to all facilities using the various controls at the front panel.
RA - 7203 Menus, 4 of 16 Push menu button to enter MAIN MENU
RA - 7203 Menus, 5 of 16
RA - 7203 Menus, 6 of 16
RA - 7203 Menus, 7 of 16 RX config subtree menu, 1 of 2
RA - 7203 Menus, 8 of 16 RX config subtree menu, 2 of 2
RA - 7203 Menus, 9 of 16 Interface config subtree menu, 1 of 2
RA - 7203 Menus, 10 of 16 Interface config subtree menu, 2 of 2
RA - 7203 Menus, 11 of 16 Bite system subtree, 1 of 2
RA - 7203 Menus, 12 of 16 Bite system subtree, 2 of 2
RA - 7203 Menus, 13 of 16 To maneuver in the menu systems, use the up-button FbA, the down-button FbB or (preferably) turn the RS. The different submenus are selected by pressing the rotary switch and turning up/down until the desired menu is reached. (FbA, FbB and FbC may be used as well) To return to previous menu, press RS (or FbC) when “ ,,,” is selected in the present menu. The RA-7203 will enter the Operator menu when turned “ON”.
RA - 7203 Menus, 14 of 16 Operator menu, 1 of 3 Normal operating display with active squelch. Press Fb C to mute squelch. PressRS Normal operating display with no channels stored. Press Fb C to recall stored channels. Press RS Set loudspeaker volume by turning RS. Press FbC to mute loudspeaker. Press RS Set headset volume by turning RS. Press FbC to mute headset.
RA - 7203 Menus, 15 of 16 Operator menu, 2 of 3 Set squelch level by turning RS. Press FbC to mute squelsh. Press RS See next page how to select frequency. Press RS Press FbC to store new frequency on specified channel. Select storing channel by turning RS. Press RS Select brightness level by turning RS.
RA - 7203 Menus, 16 of 16 Operator menu, 3 of 3 Select 8,33kHz steps by turning RS. For no changes press FbC. Press FbA Select 100kHz steps by turning RS. Press FbA Select 1MHz steps by turning RS. Press FbC Press FbC to store new frequency and return.
RA - 7203 Rear RJ45 connectors, 1 of 5 1 ANTENNA CONNECTOR 2 EARTH TAG 3 DC INPUT CONNECTOR 4 AC INPUT CONNECTOR 5 LAN CONNECTOR 6 AUX 1 CONNECTOR 7 AUX 2 CONNECTOR 1 6 2 7 3 4 8 REMOTE CONNECTOR 5 8
RA - 7203 Rear RJ45 connectors, 2 of 5 LAN interface connector Name PIN Purpose LAN_TXP 1 Tx data LAN_TXN 2 Tx data LAN_RXP 3 Rx data LAN_D3P 4 Optional LAN_D3N 5 Optional LAN_RXN 6 Rx data LAN_D4P 7 Optional LAN_D4N 8 Optional
RA - 7203 Rear RJ45 connectors, 3 of 5 Aux 1 connector Name PIN Purpose ALARM_P 1 Alarm out – rele ALARM_N 2 Alarm out – rele Select_in_P 3 Select in – opto isolated RS232_S 4 RS232 Send data RS232_R 5 RS232 Receive data Select_in_N 6 Select in – opto isolated +12V 7 12V output to ext equipment (D/O: 200mA) GND 8 Common ground
RA - 7203 Rear RJ45 connectors, 4 of 5 AUX 2 connector Name PIN Purpose Squelch_out_P 1 Squelch out - opto isolated Squelch_out_N 2 Differential – opto isolated AGC_HILO_P 3 Hi / Lo depending on input signal (configurable) NC 4 NC 5 AGC_HILO_N 6 AGC_ OUT 7 NC 8 Differential – opto isolated
RA - 7203 Rear RJ45 connectors, 5 of 5 REM connector (Interface to transmitter) Name PIN Purpose RS485_Z 1 RS485 (-) RS485_Y 2 RS485(+) LINE_P 3 Diff. line output from RX, 600 ohm TX_BUSY 4 TX Busy indicator input (Mute input) RX_BUSY 5 RX Busy indicator output (Repeater Key Output – Tx in repeater mode) LINE_N 6 Diff.
RA - 7203 External wiring RJ45 KRONE