WIRELESS KIT QUICK USER GUIDE
CONTENTS Statement 1 Safety Caution 1 Unpack Audit 1 Product overview 2 NVR 2 IPC 2 Installation Instructions 3 HDD installation 3 KIT installation 4 NVR system operation 6 Format the hard disk 6 Record Video 6 Video Playback 7 Video Backup 8 Motion Detection 9 E-Mail Setup 9 MENU Function（other function） 10 Extend the WIFI range 11 Position the Antenna Correctly 11 Repeater Setup 12
Use Antenna Extension 13 OPERATE NVR SYSTEM FROM CLIENT ON PC 14 Login 14 Add Device 14 Bottom Menu 16 OPERATE NVR SYSTEM ON MOBILE DEVICE 16 Download 16 Add Device 17 Warning 18 Q&A 19
1 Statement Thank you for purchasing our product! This quick user guide will talk about main usages of the product. More information can be found on our website and the help center. The functions, parameters, operations, etc. presented in this manual are for reference only, and Jooan may improve the content. For all specific information, please refer to the actual product. 2 Safety Caution Please do not put any fluid container on the product.
4 Product Overview This product may require cabling, we suggest to test all products&parts before installation and cabling. NVR 7 AUDIO OUT WIFI Antenna Ports: Double antennas to WIFI range; AUDIO OUT: 3.5mm audio interface for external speakers; VGA Port: For viewing on VGA monitor; HD OUTPUT Port: For viewing on HDTV; WAN Port: Connect your NVR to the Internet; USB Ports: For mouse and backup； 7 Power Input: 12V 2A NVR power interface; IPC 4 02 technicalreply@qacctv.
WiFi antenna: WiFi connection with NVR; DC Port: Input power 12V 1A; Reset button: Press reset button for 10 seconds to restore factory setting and enter into matching-code mode. Photosensitive: Used to measure light and control the turning on of infrared light. 5 installation instructions HDD installation Notes: 1.To use the video recording and playback functions, HDD must be installed. 2.The camera system doesn't come with hard drive. Recommend to choose an Monitoring dedicated Hard Drive in SATA III 3.
Step 4: Hold the Hard Disk Drive and the NVR together,carefully turn them over,then align the screw holes on the Hard Disk Drive with the screw holes on the NVR housing and put screw on. Step 5: Put the cover back to position and install the screws. KIT installation This system is standalone with embedded Linux Operating System in the NVR. Just like a desktop PC, need to hook a screen to the NVR to enter the OS. Any TV , monitor with VGA or HD-OUTPUT input should work for it.
Add the cameras to the NVR Step 1: Install antennas for cameras; Step 2: Connect a screen to the NVR via its HD-OUT port or VGA port.(The default supported screen size is 19-42".). Step 3: Plug the NVR to power.(use bigger 12V 2A power adapter.) Step 4: Plug cameras to power.(use smaller 12V 1A power adapters.) Step 5: Within seconds, you can see camera's images on the screen. Step 6: Plug the mouse to USB port on the back of NVR. So you can operate the system.
6 NVR system operation Format the hard disk Steps: After installing HDD, boot up the NVR -> Right click -> System Setup -> General Setup -> HDD Setup -> format the HDD. Note: Recommend to choose an Monitoring dedicated Hard Drive in SATA III 3.5", 1-2TB .The hard disk is installed on the device for the first time, and the hard disk needs to be formatted. Video Record Steps: Right click -> System Setup -> Record Setup -> Record Plan.
Time Recording: Click "Time" and put mouse icon on the upper left corner (for example "T" as picture shows), press and drag the mouse to the right to choose the time. The selected area will turn to red. Motion Recording: Click “Motion” and put mouse icon on the upper left corner (for example "T" as picture shows), press and drag the mouse to the right to choose the time. The selected area will turn to green.
Video search condition area: You can select the date, time, channel, and event type to query the video, and click "search" to query. Video search result area: Display the video search results under the search conditions you set. Different colors represent different event types.
Motion Detection Steps: Right click -> System Setup -> Channel Setup -> Video Detection Select the channel to enable motion detection and set the channel detection type (movement, video loss, video occlusion, etc). When the alarm sensitivity is too high or too low, the sensitivity can be adjusted to achieve the best effect. When a moving object is detected, the alarm information can be received by means of buzzer, mail, app, etc.
Step 2: enter settings and enable SMTP/IMAP service and set a authorization code(available in some email settings,not all). Step 3: Add the email address and password to the NVR, you have to input the authorization code as password if the code is unavailable. MENU Function （other function） Right click the mouse to show the main Menu bar as shown below, right click again to return or exit the current menu. Split Screen: change the numbers of the channels showing in the same screen.
Channel Setup: change encode mode, camera resolution, motion detection ect. System Admin: system version, set password, edit users, simple restore ect. Video Playback: playback recorded videos. Video Backup: backup recorded videos. Color Adjust: adjust the brightness, contrast, sharpness ect. Of the picture in each channel. PTZ Control: enter PTZ control to control camera. (requires camera to support this function.) Volume: adjust volume of audio cameras.(works only for audio cameras.
Notes: Please place the NVR far away from the devices that are easy to interfere the connection, such as microwave oven, TV ect. Make sure the obstacles between the NVR and the cameras are as few as possible. Repeater Setup As picture shown above, when IPCAM1 is put somewhere out of NVR WIFI range, and there is IPCAM2 between them with strong WIFI signal, users can put IPCAM1 close to NVR and power it, setup IPCAM1 repeated by IPCAM2, and then install IPCAM1 to the presupposed place.
Step 2: Click + to select the channel with the stronger signal value to connect to the NVR, and the weaker signal value to connect to the channel with stronger signal value. As shown in the picture, the signal values of CH1 and CH2 are strong. We can connect CH3 and CH4 behind CH1 and CH2. Step 3: Click “Apply” to finish the cascading connection. Click “Refresh” to check if it’s set successfully. To cancel selection, click on the seleted channel, then click “Apply” and “Ok”.
8 OPERATE NVR SYSTEM FROM CLIENT ON PC Please download the EseeCloud client through http://k.jooan.cc Note: This function needs to be connected to the network, please confirm the status of the NVR network in advance. Login Login Local: Log in to EseeCloud Client with default user name (admin) and Password (empty, namely enter nothing) if you did not set any password. Login Cloud: You can also register an account by phone number or email address.
Add device by IP address Switch to IP address option. Enter IP address of your device(Please choose the appropriate device type and number of channels.) Add device by Cloud ID Switch to Cloud ID option. Enter cloud ID of your device (Password is empty, namely enter nothing if you did not set any password.), click “Finish” and add device. (Please choose the appropriate device type and number of channels.) technicalreply@qacctv.
Bottom Menu Playback: Screenshot: video playback and download. take a screenshot of the current screen and save it into your computer. Device Management: Disconnect All: User Parameter: Screen Number: Record: More Funtion: add and delete device, modify information of device. change language, change the file path of saving ect. record the current video into your computer. 9 disconnect the device change the channel numbers showing in the screen.
Add Device Install and open EseeCloud App, then follow the steps below to add the NVR system. Step 1: Register an account and log in to EseeCloud, then + icon in the center or on the upper right corner to add device. Step 2: You can add NVR by scanning the cloud ID, or you can add it in other ways. (Click “Kit”, manually enter the cloud ID and password to add the NVR.) technicalreply@qacctv.
10 Warning Notes: Device will not be in guarantee if caused by below reason： Product failure due to accident, negligence, disaster, improper operation or misuse. Do not conform to the environment and conditions, such as power improper, working temperature too high or too low, lightning stroke.etc. Ever be maintained by other center which not belong to the real factory. Goods already sold more than 12 months.
11 Q&A Q1: Camera connection failed or no image. It maybe the camera did not match the code successfully,Please kindly follow page 5 to add them to the NVR. Q2: Can I add the extra new camera? The camera with the same brand is recommended when you’d like to add more cameras. To get the link of buying camera and the detailed guide for adding the camera, please contact us at market@qacctv.com. Q3: NVR system can not detect the Hard Disk Drive.
Step 2: When you are able to see the Menu, please go to System Setup -> General Setup -> General Setup -> Display Resolution to adjust the appropriate resolution, then click Ok. (For larger monitors, please choose 1024*768.) Step 3: Connect the NVR to your primary screen via again to check the dispaly. Set by IP address Step 1:Download the EseeCloud client on your computer. (The operation is on page 14.) Step 2: Connect the NVR and your computer to the same network.
Email:technicalreply@qacctv.com Skype:market@qacctv.com Tell:+1-202-945-9595 / +86-18127028076 website: k.jooan.
