Instructions / Assembly

ManualsBrandsJONATHAN Y ManualsLightingHygge 16 in. Swing Arm 1-Light Black/Brass Gold Modern Midcentury Iron USB Charging Port LED Wall Sconce

WARNING

WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.

WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER

BEFORE INSTALLATION.

INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS

DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.

CARE AND MAINTENANCE

To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe

the surface of the fixture.

To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the

fuse at the fuse box. Next, use a dry or slighly damperned clean clorth (use clean water, never a solvent) to wipe the

interior surface of the fixture.

Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.

Model#: JYL1302A，JYL1302B，JYL1302C

Product Dimensions: 16"W X 6.5"H X 14.5"E

Note: 2 Assembly Options

Option 1：Portable lamp with plug

Option 2：Hard wired

NOTICE& IMPORTANT SAFETY INSTRUCTIONS

* Please make sure that you have all parts indicated before you begin assembly of this item.

* This item should be assembled on a soft surface to prevent scratching the finish during assembly.

* To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use

and installation.

* The external flexible cable or cord of this lamp cannot be replaced. If the cord is damaged, the lamp shall be destroyed.

Option 1：Portable lamp with plug

Part List and Hardware List

PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION PICTURE QUANTITY

A wire nut 3X E wooden screw 2X

B mounting plate 1X F fixture screws 4X

C Ground Screw 1X G lamp body 1X

D Wall Anchors 2X H bulb 1X

接线粒

平头螺丝

绿螺丝

灯体

灯泡

背板

塑胶壁虎

螺丝

自攻螺丝

灯罩

外环

插头护套

接线粒

平头螺丝

绿螺丝

灯体

灯泡

背板

塑胶壁虎

螺丝

自攻螺丝

灯罩

外环

插头护套

接线粒

平头螺丝

背板

塑胶壁虎

自攻螺丝

绿螺丝

灯体

灯泡

灯罩

外环

安装板

平头螺丝

灯体

螺丝

灯泡

绿螺丝

接线粒

平头螺丝

背板

塑胶壁虎

绿螺丝

灯体

灯泡

自攻螺丝

安装板

平头螺丝

灯体

螺丝

灯泡

绿螺丝

接线粒

平头螺丝

背板

塑胶壁虎

绿螺丝

灯体

灯泡

自攻螺丝

1/5

Summary of content (5 pages)

PAGE 1
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
PAGE 2
PREPARATION Step 1 Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes. A D B C D E G 1.Place mounting plate (B) on the wall and use a marker to mark the hole in the mounting plate . 2.Secure mounting plate (B) to the wall with Wall Anchors(D) and wooden screw(E).
PAGE 3
Option 2：Hard wired WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
PAGE 4
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes. Step 1 1.Cut off the plug with scissors, leaving the exposed wire 8" in length. Note: Cuting the cord so that they are at least 6 inches (152.4mm) long within an outlet box and extend max. 2.
PAGE 5
Connect, Hot, Black or Red Outlet Supply Wire to: Connect, Neutral, White Outlet Supply Wire to: Black White * Parallel Cord (round & smooth) * Parallel Cord (square & ridged) Clear, Brown, Gold or Black without Tracer (colored stripes) Insulated Wire (not green) with copper metal conductor Clear, Brown, Gold or Black with Tracer (colored stripes) Insulated Wire (not green) with Silver metal conductor. *Note: When parallel wire ( SPT I & SPT II ) is used.