Spot-Lock SPOT LOCK FISHFINDER OPERATIONS minnkot amot or s.
WAYPOINT REMOTE OPERATIONS H ow WAYP O I N T NAV I G AT ION Wo rks Waypoints are stored positions that allow you to mark areas of interest or navigation points. Your Fishfinder can store up to 2,750 Waypoints. MARK A WAYPOINT 12:13 PM OCT 18 PROP 12 5/ S P E ED 2 DEPTH 1 ft .3 BEAR ING 273° Settings 1. To create a Waypoint at the boat’s position, press and hold the Spot-Lock key. TARG E T 0 .0 This Waypoint will be saved on the Humminbird.
WAYPOINT FISHFINDER OPERATIONS Mark a Waypoint 1. Press the VIEW key until a Chart View is displayed on the screen. 2. A Waypoint can be marked as follows: To save the Waypoint at the boat’s location, press the MARK key. To save a Waypoint at a cursor position, use the 4-WAY Cursor Control key to move the active cursor to a position on the Chart View. Then, press the MARK key.
WAYPOINT FISHFINDER REMOTE OPERATIONS Chart View with Waypoints, Routes, iTracks Waypoint Route Spot-Lock iTrack (gray line) i-Pilot Link Icon indicates i-Pilot Link navigation is in progress Move the Cursor 58 minnkot amot or s.
WAYPOINT FISHFINDER OPERATIONS engage Spot-Lock at a waypoint position 1. Use the 4-WAY Cursor Control key to move the cursor to a Waypoint on the chart. 2. Navigation X-Press Menu: Press the MENU key. 3. Select the Waypoint name > Spot-Lock. If the waypoint is within a 1⁄4 mile, i-Pilot Link navigation will start towards the Waypoint. When the boat arrives at the Waypoint, Spot-Lock will start automatically. minnkot amot or s.
iTRACKS HOW iT RAC K RE CO R D I N G AND NAVIG AT ION WO R K When the recording of an iTrack is initiated, i-Pilot Link starts to record GPS position data in the form of track points. The distance between these points varies based on the speed of the boat and the GPS signal strength. The very first track point recorded is called the Start. The last point recorded is called the End. i-Pilot Link sees a recorded track as a series of these track points.
iTRACKS minnkot amot or s.
iTRACKS REMOTE OPERATIONS 12:13 PM OCT 18 PROP 12 5/ SPEED 2 DEPTH 1 ft .3 BEAR ING 273° TARG E T 0 .0 D ISTANCE 114 ft RECORDING AN iTRACK 1. To begin recording select Home>Controls>Record>OK 2. To stop the recording, press the StopRec Softkey on the Settings iTrack Active Screen. Controls a. The user will then be prompted to Save or Discard the recorded iTrack. OK NAVIGATE AN iTRACK 1. Manually navigate the boat to within a quarter mile of any point on the iTrack. 2.
iTRACKS REMOTE OPERATIONS Record an itrack 1. Main Menu: Press the MENU key twice. 2. Select the Accessories tab. 3. Select Record iTrack, and press the RIGHT Cursor key. 4. Press the EXIT key until the menu system is closed. As you navigate, iTrack Record will flash on the screen periodically to indicate that a recording is in progress. Stop Recording 1. Press the MENU key. 2. Select Stop Recording iTrack, and press the RIGHT Cursor key. Follow the on-screen instructions to save or discard the iTrack.
RECORD A TRACK FISHFINDER OPERATIONS Recording an iTrack iTrack being recorded Recorded iTrack (red) Traditional iTrack (gray) Navigate a Saved iTrack from the Go To list 1. Press the GOTO key. 2. Select an iTrack Start or iTrack End from the Go To list. iTracks are saved with an alphanumeric name that stars with IT. iTracks are a special class of navigation data. The iTrack can be renamed and it will still appear under the list of iTracks.
Selecting a Saved iTrack from the Go To list Go To List Select to Start Navigation Select to Start Navigation from the End Point to the Start Point RD A TRACK OPERATIONS Open the Go To List Select a Saved iTrack Navigating an iTrack Track (gray line) iTrack Start Point iTrack (red line) iTrack End Point minnkot amot or s.
BACKTRACK FISHFINDER OPERATIONS How BackTrack Works Traditional Humminbird Tracks consist of detailed position history and are displayed as a breadcrumb trail of trackpoints. The Current Track shows the position history since the unit was powered up. You can clear the Current Track or save it at any time. Your Fishfinder can store up to 50 saved tracks, each containing 20,000 trackpoints. The current track represents your actual path so far.
BACKTRACK FISHFINDER OPERATIONS BackTrack Applies an iTrack to the Current Track BackTrack (Yellow line) When you select BackTrack, the iTrack Start Point begins at the boat position. iTrack End Point minnkot amot or s.
FOLLOW THE CONTOUR REMOTE OPERATIONS H OW follow the co n to u r WO R KS NOTE: Initiation of Follow the Contour is done through the Humminbird. 12:13 PM OCT 18 PROP 12 5/ SPEED 2 DEPTH 1 ft .3 BEAR ING 273° TARG E T 0 .0 D ISTANCE 114 ft REVERSE DIRECTION 1. During navigation of a contour, the direction of travel can Settings be reversed by pressing: Home>Controls>Reverse>OK Controls OK DISENGAGE CONTOUR NAVIGATION 1.
FOLLOW THE CONTOUR FISHFINDER OPERATIONS How Lakemaster contour works (Chart View only, Lakemaster chart required) Follow the Contour allows you to navigate a contour on a LakeMaster chart. When you start i-Pilot Link navigation to follow the contour, all other types of navigation are stopped on the Humminbird and the Ethernet network. NOTE: When the i-Pilot Link is following the contour, the current track is not saved, and iTracks cannot be recorded.
FOLLOW THE CONTOUR FISHFINDER OPERATIONS Starting Follow the Contour Navigation Submenu Navigation Option 1 (orange) Contour Line(s) Navigation Option 2 (gray) Navigation Option 1 (previewed in orange) Boat Icon (idle) Cursor selecting a contour Navigation Option 2 (previewed in gray) Move the Cursor Open the Contour Submenu Following the Contour Projected Contour Line (changes to yellow when Follow the Contour is active) Boat Icon (navigating) i-Pilot Link Icon indicates i-Pilot Link navigation is
FOLLOW THE CONTOUR FISHFINDER OPERATIONS set the contour offset If you don’t want to navigate directly on the contour line, you can set a distance from the contour so that navigation will be offset from the selected contour. 1. Use the 4-WAY Cursor Control key to move the cursor to a contour line. 2. Press the GOTO key. 3. Select Follow the Contour, and select Contour Offset from the submenu. 4. Press the RIGHT or LEFT Cursor keys to set the Offset.
ROUTE NAVIGATION REMOTE OPERATIONS how rou t e navig ati o n wo rks Routes link two or more Waypoints together to create a path for navigation and are used in trip planning. Your Fishfinder can store up to 45 routes that can each contain up to 50 Waypoints. A route represents your intended navigation and shows the shortest path from each Waypoint to the next.