Owner’s Manual
TABLE OF CONTENTS Introduction ...................................................................................... 3 Two-Year Warranty ........................................................................ 4-5 Installation.................................................................................... 6-25 Parts List............................................................................................6-9 Preparing for Installation ..............................................................
I N TRO D UCT IO N Overview Thank you for purchasing the Minn Kota® i-Pilot®. This revolutionary control system uses GPS technology to record and store tracks and locations which are then used to deliver unprecedented levels of boat control. Intuitive features and wireless control help to accurately position your boat and improve your bait presentation. i-Pilot navigates and positions your boat for you, so you can focus on fishing.
LIMITED T WO-YEAR WARRANT Y ON ENTIRE PRODUCT: Johnson Outdoors Inc. warrants to the original purchaser that the purchaser’s entire i-Pilot System® accessory is free from defects in materials and workmanship appearing within two (2) years after the date of purchase. Johnson Outdoors Inc. will, at its option, either repair or replace, free of charge, any parts found to be defective during the term of this warranty. Such repair or replacement shall be the sole and exclusive liability of Johnson Outdoors Inc.
1-800-227-6433, 1-507-345-4623 or fax 1-800-527-4464. Note: Do not return your i-Pilot or parts to your retailer. Your retailer is not authorized to repair or replace them. THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. IN NO EVENT SHALL ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXTEND BEYOND TWO YEARS FROM THE DATE OF PURCHASE. IN NO EVENT SHALL JOHNSON OUTDOORS MARINE ELECTRONICS L.L.C.
PA RTS L I S T V I E W T E R ROVA ITEM # PART NUMBER DESCRIPTION 1 2990270 I-PILOT CONTROLLER, TERROVA 1 2 2994170 REMOTE, ASSEMBLY I-PILOT 1 3 2372100 SCREW, #8-18 X 5/8" SS 4 4* 2377152 MANUAL, I-PILOT 1 5* 2377153 MANUAL, I-PILOT QUICK REFERENCE GUIDE 1 6* 2370817 LANYARD, REMOTE WITH CARABINEER 1 * Not Shown In Exploded View 6 QTY min n kot a m ot o r s .
INSTALLATION PA RTS L I S T V I E W R I P T I D E S T ITEM # PART NUMBER 1 2990271 I-PILOT CONTROLLER, RIPTIDE ST 1 2 2994170 REMOTE, ASSEMBLY I-PILOT 1 3 2372100 SCREW, #8-18 X 5/8" SS 4 4* 2377152 MANUAL, I-PILOT 1 5* 2377153 MANUAL, I-PILOT QUICK REFERENCE GUIDE 1 6* 2370817 LANYARD, REMOTE WITH CARABINEER 1 DESCRIPTION QTY * Not Shown In Exploded View min n kot a m ot o r s .
PA RTS L I S T V I E W P OW E R D R I V E V 2 ITEM # PART NUMBER DESCRIPTION 1 2990272 I-PILOT CONTROLLER, POWERDRIVE V2 1 2 2994170 REMOTE, ASSEMBLY I-PILOT 1 3 2372100 SCREW, #8-18 X 5/8" SS 4 4 2224704 INSERT PLUG, BLACK SLOTTED 1 5 2376312 TIE, NYLON 5 6 2375403 HEAT SHRINK, .
INSTALLATION PA RTS L I S T V I E W R I P T I D E S P ITEM # PART NUMBER DESCRIPTION 1 2990273 I-PILOT CONTROLLER, RIPTIDE SP 1 2 2994170 REMOTE, ASSEMBLY I-PILOT 1 QTY 3 2372100 SCREW, #8-18 X 5/8" SS 4 4 2224705 INSERT PLUG, WHITE SLOTTED 1 5 2376312 TIE, NYLON 5 6 2375403 HEAT SHRINK, .
P R E PA R I N G F O R I N S TA L L AT I O N Preparing for Installation Tools you will need during installation Terrova and Riptide ST -Phillips screwdriver PowerDrive V2 -Phillips screwdriver -Needle-nose pliers -Utility knife -Heat gun or other heat source for installing heat shrink Riptide SP -Phillips screwdriver -Needle-nose pliers -Utility knife -Heat gun or other heat source for installing heat shrink To help with future service work or ordering replacement parts, please refer to the information b
INSTALLATION I N S TA L L AT I O N O F I - P I LOT CON TRO L L ER For PowerDrive V2 and Riptide SP trolling motors go to page 13. i-Pilot Installation on Terrova and Riptide ST Trolling Motors *i-Pilot will override all CoPilot functionality. CoPilot remotes will not function with i-Pilot. FIGURE 1 *The Terrova foot pedal is fully functional and supported when i-Pilot is installed correctly. 1. Remove all power to the trolling motor. 2.
4. Plug the i-Pilot controller connector into the accessory connector as shown. (Figure 4) Be careful to orient connector properly prior to pushing together. The plug will click twice when pushing it together and the yellow end will be fully covered when installed properly. Make sure connector is aligned properly. (Figure 5) FIGURE 4 Make sure connector is fully seated as shown. (Figure 5) 5. Place the i-Pilot controller where the control box cover was installed and secure with supplied #8 screws.
INSTALLATION i-Pilot Installation on PowerDrive V2 and Riptide SP *Note: Once i-Pilot is installed in a PowerDrive V2 or Riptide SP motor, the foot pedal cannot be used again unless i-Pilot is fully uninstalled. 1. Remove all power to the trolling motor. 2. If a CoPilot is installed, it must be removed as follows: FIGURE 6 a. Disconnect motor connector and foot pedal connector from CoPilot. (Figure 7) b. Remove the CoPilot receiver from the motor by removing both mounting screws.
3. Remove control box cover screws and cover using Phillips screwdriver. (Figure 9) 4. If the trolling motor has AutoPilot it must be removed as follows: FIGURE 9 FIGURE 10 FIGURE 11 14 m i n n kot a m ot o r s . c o m min a. Disconnect all six AutoPilot connectors from AutoPilot controller, using a needle-nose pliers and a utility knife to remove any heat shrink insulation that may exist. (Figure 10) b. Remove the AutoPilot controller from the head of the trolling motor.
INSTALLATION 5. Remove grommet by pulling back on coil cord strain relief and pushing down on grommet until it pops out. (Figure 12) Grommet 6. Review the cables in the head of the trolling motor. a. If a sonar cable is present, it must be routed around the outer perimeter of the control box. The sonar ground wire should also be routed as shown. (Figure 13) FIGURE 12 Sonar Cable (Universal Sonar Motors Only) b. The motor power wires must be routed as shown.
7. Route i-Pilot controller cable through grommet hole and through center of coil cord. (Figure 14) 8. If AutoPilot was removed, insulate the loose AutoPilot connectors as follows: FIGURE 14 FIGURE 15 Insert AutoPilot wires into terminal holders. a. For PowerDrive V2 Motors: Using a needle-nose pliers push all six AutoPilot connectors that were disconnected in step 4 onto terminal holders located on the underside of the i-Pilot Controller.
INSTALLATION b. For Riptide SP Motors: Apply heat shrink insulation supplied in bag assembly to the ends of all six loose AutoPilot connectors as shown. (Figure 17) Use a zip tie to bundle connectors together. Trim the zip tie and place connector bundle in the middle of the control box as shown. (Figure 18) Pinch ends of heat shrink shut using needle-nose pliers. FIGURE 17 Insulate and seal six AutoPilot wires on Riptide SP motors with supplied heat shrink.
9. Install new grommet supplied with i-Pilot by snapping it into the hole located in front of the coil cord strain relief. The i-Pilot controller cable must be placed in the pass-through slot of the grommet. (Figure 19) FIGURE 19 10. Place the i-Pilot controller where the control box cover was installed. Pull any extra controller cable out of the control box by gently pulling on the cable. (Figure 20) 11. Secure cover with supplied #8 screws. Do not over tighten screws.
INSTALLATION 12. Secure the i-Pilot controller cable to the motor coil cord in all three locations shown using zip ties provided. (Figure 22) Trim zip ties using utility knife. Failure to secure cable will result in possible damage to the cabling during operation. 13. Remove the left and right side plates of trolling motor by loosening all four side plate screws using a Phillips screwdriver.
14. Remove center housing by pushing in on both sides and lifting up at the same time. This will expose the main control board and wiring. (Figure 24) FIGURE 24 FIGURE 25 20 Entrance of steering cable through center housing Disconnect both wires by removing heat shrink and pulling them apart. m i n n kot a m ot o r s .
INSTALLATION 15. The steering motor cable passes through the top of the center housing removed in step 14. This cable contains a black and white wire. Disconnect these two wires by pulling each connector apart. (Figure 25) Riptide SP motors will have this connections covered with heat shrink which must be removed with a utility knife. 16. Loosen the cable strain relief that is secured to the base of the motor and install the i-Pilot controller steering cable into the open strain relief slot.
17. Tighten the cable strain relief as shown. The i-Pilot controller steering cable should slide freely through the strain relief when installed properly. (Figures 27 and 28) Foot Pedal Cable Motor Power Cable i-Pilot Controller Steering Cable Reinstall strain relief screw. FIGURE 27 and 28 22 m i n n kot a m ot o r s .
INSTALLATION 18. Slide four pieces of heat shrink insulation over each side of the wires that were disconnected in step 15. (Figure 29) Slide heat shrink over steering motor wires. FIGURE 29 m i n n kot a m ot o r s .
19. Connect the black and white wires from the i-Pilot controller cable to the back and white steering motor wires, making sure black is connected to black and white is connected to white. (Figure 30) Connect steering wires: white to white black to black FIGURE 30 24 m i n n kot a m ot o r s .
INSTALLATION 20. Complete the installation by positioning the heat shrink over the connections and shrink down, using a heat gun or other heat source, being careful not to overheat any wire or parts. Seal connections with heat shrink. IMPORTANT: DO NOT OVERHEAT WIRES OR SURROUNDING PARTS WHEN INSTALLING HEAT SHRINK! 21. Reinstall center housing over control board by pushing it down until the side fingers lock into place.
FIGURE 32 FIGURE 33 26 m i n n kot a m ot o r s .
INSTALLATION 22. Reinstall both side plates using Phillips screwdriver. If a Co-Pilot was uninstalled, use new ¼-20 X 5/8" Phillips screws provided. (Figure 32) 23. If a foot pedal is connected to the trolling motor, it must be disconnected. Once i-Pilot has been installed the foot pedal cannot be used unless i-Pilot is completely uninstalled. 24. Connect i-Pilot controller cable to the foot pedal connector, making sure the connector nut is tight.
V E R I F Y I N G I N S TA L L AT I O N It is important to verify your i-Pilot installation prior to going on the water. If this cannot be done, it is highly recommended that system verification be done in an open area on a calm day with a fully operational outboard motor for a backup means of powering your boat. To verify that i-Pilot is working properly before going on the water, follow the steps below. 1. Trolling motor should be correctly installed and mounted to the bow of a boat. 2.
INSTALLATION 9. When i-Pilot is powered up, it starts to gather satellite information about its location. A minimum satellite signal level must be achieved before all i-Pilot functionality is available. This minimum level is one bar on the GPS signal icon. At initial startup only manual functions will be available. 10. Verify all manual functions by pressing and . 11.
K N OW I N G YO U R R E M OT E Layout The i-Pilot remote is divided into four sections: Manual Control, Tracks, Spot Lock, and Cruise Control/AutoPilot. Buttons in the Manual Control section of the remote do not require a GPS signal to operate and give you full, immediate control over steering, speed and prop functions similar to a CoPilot. All other buttons require a minimum GPS signal strength of one bar in order to operate. Buttons located in the Tracks section are used for track recording and playback.
GETTING STARTED min n kot a m ot o r s .
Remote Battery Replacement 1. Make sure hands are clean, dry and static free. Discharge any static electricity by touching a metal object that is grounded. *Static electricity can damage the circuit board. FIGURE A 2. With the remote upside down, use a large coin to rotate the battery door counterclockwise until either of the Unlock icons align with the arrow (see Figure B). 3. Remove battery cover and old battery and replace with new CR2450 coin cell battery.
GETTING STARTED K N OW I N G YO U R I -P I LOT CO N T RO L LER Construction The i-Pilot controller contains a very sensitive digital compass and is where all GPS satellite and i-Pilot remote signals are received. It is very important that the controller have a clear view of the sky in all directions and has a clear line of sight to the remote for optimum performance. All electronics within the controller i-Pilot enclosure are completely sealed.
Audio Modes The i-Pilot Controller also contains an internal speaker which can be programmed to work in two different audio modes. The speaker is programmed to operate in audio mode one from the factory. To enable and down at the same time for three different audio modes hold seconds. For an explanation of each audio mode and their sounds see the table below.
GETTING STARTED WHAT CONDITION CAUSES IT Attempting to enable a GPS feature when no signal strength bars are shown Attempting to replay a Track or recall a Spot Lock location when the boat is beyond the minimum distance MOM button on the footpedal is pressed and a remote button press attempts to override it End of track attained during track playback (in conjunction with cancelling mode and turning the prop off) Switch to Audio Mode 1 Switch to Audio Mode 2 Learn button is pressed Learn successfully comple
Power The i-Pilot controller will turn on whenever the trolling motor has power. For Terrova and Riptide ST motors this is when the green system ready light is on. For PowerDrive V2 and Riptide SP motors this is whenever the motor is connected to power. * For this reason it is very important to disconnect a PowerDrive V2 or Riptide SP motor from power when not in use or battery drain will occur.
GETTING STARTED System Startup Once you have verified i-Pilot’s installation it’s time to start using it on the water. Follow these simple steps each time you power up your trolling motor for successful operation: 1. Connect trolling motor to power. 2. Deploy trolling motor into water. 3 Push any button on your remote. The remote LCD will show prop speed and GPS signal strength. 4. You are now able to use all manual functions: and . 5.