P R O O F JDLINK Machine Messenger INSTALLATION INSTRUCTIONS JDLINK Machine Messenger PC20103 09JAN02 (ENGLISH) P R O O F 8020, 9020 John Deere Ag Management Solutions PC20103 (09JAN02) COPYRIGHT 2001 DEERE & COMPANY Moline, Illinois All rights reserved A John Deere ILLUSTRUCTION Manual PC20103-19-09JAN02
P R O O F Installation Instructions Recognize Safety Information JDLINK Wiring Harness Reference 1 T81389 PC6782 P R O O F (09JAN02) –UN–19DEC01 PC6783 A—Socket Connector To Controller B—CAN Bus Terminator Connector C—Ground wire D—CCD Bus Connector E—CAN Bus Terminator Connector F—Unswitched And Switch Power Wires G—SCV Panel Connector H—10 Amp Fuses DX,ALERT –19–29SEP98–1/1 –UN–19DEC01 Follow recommended precautions and safe operating practices. –UN–07DEC88 This is a safety-alert symbol.
P R O O F Installation Instructions Install JDLINK Machine Messenger IMPORTANT: Avoid damage to electrical system of tractor when installing JDLINK wiring harness. Disconnect battery ground. NOTE: After installing JDLINK Machine Messenger and before reassembling cab roof, login to JDLINK website at www.jdlink.com, go to Dealer Menu/Setup New Device wizard and follow online procedures.
P R O O F –UN–28NOV01 P R O O F OUO6091,0001433 –19–14AUG01–2/27 Installation Instructions 3. Remove plastic rivets (B). 4. Remove cap screw (C). NOTE: To access console screws (D), remove fuse panel cover. 5. Remove screws (D) and console cover (E). TORX is a trademark of Camcar/Textron (09JAN02) Continued on next page 3 PC6930 –UN–28NOV01 PC6931 –UN–29NOV01 PC6929 A—TORX Screws B—Plastic Rivets C—Cap Screw D—Screws E—Console Cover PC6928 2. Remove TORX screws (A).
P R O O F Installation Instructions PC6764 A—Shroud Screws B—Post Shroud –UN–14AUG01 6. Remove right rear shroud screws (A) and shroud (B). OUO6091,0001433 –19–14AUG01–3/27 7. Remove screw (A), light (B), trim screws (C) and headliner trim (D). PC6934 A—Screw B—Light C—Trim Screws D—Trim –UN–28NOV01 NOTE: Remove headliner enough to route wiring harness down right-rear corner post. OUO6091,0001433 –19–14AUG01–4/27 PC6933 P R O O F A—Rear Window Molding –UN–28NOV01 8.
P R O O F Installation Instructions 11. Remove flange cap screws (A) and mirror (B). 12. Disconnect and remove STARFIRE receiver, if equipped. NOTE: Refer to machine Technical Manual for removal of rear cab lights and radio antenna. A—Cap Screws B—Mirror P R O O F STARFIRE is a trademark of Deere & Company OUO6091,0001433 –19–14AUG01–7/27 PC6762 13. Remove rear cab lights and disconnect radio antenna. PC6767 A—CAN Bus Terminator –UN–14AUG01 10. Disconnect and remove CAN bus terminator (A).
P R O O F Installation Instructions 15. Connect coax cables (A and B) to antenna assembly (C). PC6781 –UN–20AUG01 IMPORTANT: Improperly installed antenna and receiver may interfere with the operation of machine’s electronic system and possibly subject operator to higher than recommended radio frequency emission levels. PC6771 A—Coax B—Coax C—Antenna Assembly D—Cap Screws –UN–20AUG01 16. Attach antenna assembly to right rear-window hinge using existing cap screws (D).
P R O O F Installation Instructions –UN–14AUG01 NOTE: Use pullout templates (included with this instruction) to locate and drill holes at left front section of cab. Templates below are for reference only. If tractor is equipped with JDLINK wiring harness, skip to step 21. 20. Drill four 8 mm (5/16 in) holes (B). (09JAN02) 7 PC6760 P R O O F Continued on next page –UN–10AUG01 PC6769 A—Template B—Hole Guides –UN–16AUG01 19. Remove templates. PC6768 18.
P R O O F 22. Connect JDLINK wiring harness connector (C) to controller and tighten cap screw (D). NOTE: Record controller’s 13 digit serial number for a following step. 23. Install terminator (E) and retain with tie straps. PC6773 21. Attach coax cables (A) to controller (B). –UN–28NOV01 Installation Instructions OUO6091,0001433 –19–14AUG01–13/27 24. Attach controller (A), using four 6 mm cap screws (B). PC6780 A—Controller B—Cap Screws (4 used) C—Ground Wire D—Nut –UN–28NOV01 25.
P R O O F Installation Instructions Place controller ground wire next to chassis behind second nut. 26. Route ground wire (C) along side of windshield washer hose and connect to chassis ground (E). A –UN–15AUG01 If equipped with JDLINK wiring harness skip to step 32. B D C PC6761 NOTE: Record machine’s 13 digit serial number for a following step.
P R O O F PC6939 A—JDLINK Wiring Harness B—Cab Slot PC6775 27. Route JDLINK wiring harness (A) to SCV panel through slot (B) at right rear cab post. –UN–28NOV01 IMPORTANT: Avoid damage to antenna coax cables and JDLINK wiring harness when reinstalling cab roof. Tie strap wiring harness and coax cables in areas on top of cab to prevent damage of wires and cables (tie strap cables and wiring harness together from right rear cab slot to controller).
P R O O F Installation Instructions A—JDLINK SCV Connector B—SCV Panel Wiring Harness Connector Continued on next page PC6778 30. Connect JDLINK SCV connector (B) to SCV panel wiring harness connector (A). –UN–14AUG01 NOTE: Reference JDLINK wiring harness at beginning of instruction for CCD Bus connector.
P R O O F Installation Instructions IMPORTANT: Avoid damage to machine, reinstall machine enough to be moved but do not fully reassemble until proper operation of JDLINK is confirmed. PC6969 32. Reconnect battery ground. –UN–19DEC01 31. Connect JDLINK wiring harness CCD Bus connector (A) to SCV panel (B). 33. To properly confirm operation of JDLINK, move machine to an open area so it has clear view of sky horizon. 34. Shut off engine , set parking brake. A—CCD Bus Connector B—SCV Panel 35.
P R O O F Installation Instructions NOTE: If equipped with JDLINK wiring harness skip to step 47. Continued on next page PC6766 A—Screw B—SCV Panel Spacer C—SCV Panel –UN–28NOV01 39. Reinstall SCV panel (C), panel spacer (B) and retain with screw (A).
P R O O F Installation Instructions 42. Reinstall TORX screws (A). (09JAN02) 14 PC6929 –UN–28NOV01 PC6928 P R O O F Continued on next page –UN–28NOV01 PC6931 A—TORX Screws B—Rivets C—Cap Screw D—Screws E—Console PC6930 41. Reinstall cap screw (C) and new rivets (B). –UN–29NOV01 40. Reinstall console (E) and screws (D). –UN–28NOV01 NOTE: After reinstallation of console, reinstall fuse panel cover.
P R O O F 44. Reinstall headliner trim (D) retain with screws (C). 45. Reinstall light (B) and retain with screw (A). OUO6091,0001433 –19–14AUG01–23/27 PC6934 A—Screw B—Light C—Trim D—Trim Screws PC6933 A—Rear Window Molding –UN–28NOV01 43. Reinstall rear window molding (A). –UN–28NOV01 Installation Instructions OUO6091,0001433 –19–14AUG01–24/27 47. Reinstall roof (C) and retain with washers and cap screws (A and B).
P R O O F 49. Reinstall STARFIRE receiver, if equipped. A—Cap Screws B—Mirror PC6762 48. Reinstall mirror (B) and retain with cap screws (A).