PROOF *OMPFP15955* JDLink™ Modular Telematics Gateway 4G LTE, Service ADVISOR™ Remote, and Ethernet Switch OPERATOR'S MANUAL JDLink™ Modular Telematics Gateway 4G LTE, Service ADVISOR™ Remote, and Ethernet Switch OMPFP15955 ISSUE F6 (ENGLISH) PROOF CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.
Introduction PROOF Foreword THANK YOU for purchasing a John Deere product. Your dealer also needs these numbers when you order parts. File a backup of the identification numbers in a safe location off the machine or away from the product. READ THIS MANUAL carefully to learn how to operate and service your product correctly. Failure to do so could result in personal injury or equipment damage. This manual and safety signs on your product may also be available in other languages.
Contents PROOF Page Safety Recognize Safety Information ............................05-1 Understand Signal Words...................................05-1 Follow Safety Instructions...................................05-1 Practice Safe Maintenance.................................05-2 Use Steps and Handholds Correctly ..................05-2 Handle Electronic Components and Brackets Safely ..............................................05-3 Use Electronic Display Properly .........................
Contents PROOF PROOF ii 062816 PN=2
Follow recommended precautions and safe operating practices. Understand Signal Words A signal word—DANGER, WARNING, or CAUTION—is used with the safety-alert symbol. DANGER identifies the most serious hazards. DANGER or WARNING safety signs are located near specific hazards. General precautions are listed on CAUTION safety signs. CAUTION also calls attention to safety messages in this manual. DX,ALERT -19-29SEP98-1/1 TS187 —19—30SEP88 This is a safety-alert symbol.
Understand service procedure before doing work. Keep area clean and dry. Never lubricate, service, or adjust machine while it is moving. Keep hands, feet , and clothing from power-driven parts. Disengage all power and operate controls to relieve pressure. Lower equipment to the ground. Stop the engine. Remove the key. Allow machine to cool. Securely support any machine elements that must be raised for service work. Keep all parts in good condition and properly installed. Fix damage immediately.
If installing or servicing a RTK base station on a tower or other tall structure, use a certified climber. If installing or servicing a global positioning receiver mast used on an implement, use proper lifting techniques and wear proper protective equipment. The mast is heavy and can be awkward to handle. Two people are required when mounting locations are not accessible from the ground or from a service platform.
Regulatory and Compliance Information Modular Telematics Gateway 4G LTE and Satellite Module These devices comply with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: (1) These devices may not cause harmful interference, and (2) these devices must accept any interference received, including interference that may cause undesired operation. These devices must be operated as supplied by John Deere Ag Management Solutions.
Regulatory and Compliance Information PROOF Industry Canada Notifications to User GPS / GSM / Wireless Antenna: Omnidirectional John Deere JDLink™ This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Modular Telematics Gateway 4G LTE and Satellite Module.
Regulatory and Compliance Information PROOF 20-3 PC22800 —UN—28JUN16 PROOF Bluetooth is a trademark of Bluetooth SIG AE77568,00001F9 -19-28JUN16-2/2 062816 PN=10
Regulatory and Compliance Information PROOF Third Party Software Notifications and Licenses Copies of those licenses are included in the Third Party Notices. The copyrights for certain portions of the Software may be owned or licensed by other third parties (“Third Party Software”) and used and distributed under license. The Third Party Notices include the acknowledgements, notices, and licenses for the Third Party Software.
Modular Telematics Gateway 4G LTE Use the date code (A) on the product label to identify the date of manufacture. “YY" (B) identifies the last two numbers of the year of manufacture; “WW” (C) identifies the week number of calendar year of manufacture. NOTE: The week number of manufacture ranges between 01-53.
Regulatory and Compliance Information PROOF EC Declaration of Conformity Deere & Company Moline, Illinois U.S.A.
Regulatory and Compliance Information PROOF EC Declaration of Conformity Deere & Company Moline, Illinois U.S.A.
Regulatory and Compliance Information PROOF EC Declaration of Conformity Deere & Company Moline, Illinois U.S.A.
PROOF Continued on next page 20-9 PC20930 —UN—11MAR15 PROOF Customs Union–EAC PC22192 —UN—24FEB16 Regulatory and Compliance Information AE77568,00001AE -19-24FEB16-1/3 062816 PN=16
PROOF 20-10 PC20931 —UN—16MAR15 PROOF Continued on next page PC22193 —UN—24FEB16 Regulatory and Compliance Information AE77568,00001AE -19-24FEB16-2/3 062816 PN=17
PROOF PC20932 —UN—16MAR15 PROOF 20-11 PC22194 —UN—24FEB16 Regulatory and Compliance Information AE77568,00001AE -19-24FEB16-3/3 062816 PN=18
System Overview Modular telematics gateway (MTG) is one of the main components that enable John Deere telematics solutions, including JDLink™. MTG is a controller that contains firmware, a cellular modem, and a subscriber identification module (SIM) device. MTG transfers data to and from the JDLink™ host server over a cellular network. MTG also contains a wireless modem that is used to transfer data when connected to a wireless network.
NOTE: Turn key switch Off before inserting or changing SIM card. 1. Remove cap screws (A) and SIM insert (B). 2. Insert micro SIM card (C) into slot (D) as illustrated. 3. Reinstall insert and cap screws. A—Cap Screw (2 used) B—SIM Insert C—Micro SIM Card D—Micro SIM Card Slot Satellite Module Theory of Operation In select regions, an optional satellite module is offered that is a companion to the modular telematics gateway (MTG).
System Overview The JDLink / ZXLink product enables John Deere and John Deere dealers to access any data generated by the use of, collected by, or stored in the JDLink / ZXLink product or any device interfacing with the JDLink / ZXLink product (“Machine Data”).
System Overview NOTE: Not all functions are included in all levels of service. Contact your John Deere dealer or visit StellarSupport.com for more information. NOTE: Not all levels of service are available in all countries. Contact your John Deere dealer or visit StellarSupport.com for availability. PROOF JDLink™ Functions NOTE: Not all levels of service are compatible with all machines. Contact your John Deere dealer or visit Stellar Support.com for complete list.
System Overview PROOF PC15291 —UN—26NOV12 Satellite Module Service Level When the Satellite Module is in use, data from several JDLink™ functions are transferred from the machine to the website. However, not all functions are supported by the Satellite Module. The MTG is able to store this remaining data not sent by the Satellite Module for up to 1000 hours. On the next cellular call, the most recent 1000 hr of stored data is transferred to the website from the MTG.
Component Overview PROOF • Satellite Module and Antenna (optional) JDLink™ system comprises the following hardware components: • • Modular Telematics Gateway • Cellular, GPS, and Wireless Antenna • Wireless Antenna (may not be included depending on machine type) JDLink is a trademark of Deere & Company Modular Telematics Gateway MTG 4G LTE controller contains a main processor, cellular modem, GPS chipset, Subscriber Identity Module (SIM) card slot for customer-owned SIM in applicable countries, commu
PROOF LED status indicator (A) indicates MTG’s current state.
Component Overview NOTE: Satellite Module is not offered and usage is not legal in all regions. Check with your John Deere dealer for availability. Optional Satellite Module is intended to be a slave to the modular telematics gateway (MTG), and does not function properly as a standalone. In locations with poor cell coverage, the Satellite Module can be used to communicate instead of the MTG. The Satellite Module utilizes a single coaxial TNC connector for the antenna. The connector is a TNC receptacle.
Ethernet switch OCTOPUS 5TX-EEC has been especially designed for use in agricultural environments. It supports Ethernet 10 MBit/s and Fast Ethernet 100 MBit/s. Ethernet switch modules support switched Ethernet networks in accordance with IEEE standard 802.3 (10BASE-T) or 802.3u (100BASE-TX) using copper technology. Switch modules are fitted at installation site using screws. OCTOPUS 5TX-EEC modules have five 10/100 Mbit/s twisted pair ports (10BASET/100BASE-TX, shielded M12 connectors).
Operating—JDLink™ Website Creation of a Customer Account is required for new JDLink™ customers. Contact your John Deere dealer for assistance with creating a user name and password for your JDLink™ account. When entering JDLink™ website, operator is prompted to enter user name and password. Operators with access JDLink is a trademark of Deere & Company Getting Started JDLink / ZXLink Setup Setup for the MTG can only be done through the JDLink / ZXLink website or by the dealer via Service ADVISOR.
Operating—Service ADVISOR™ Remote Service ADVISOR™ Remote (SAR) information in this manual is applicable to John Deere agricultural machines equipped with a compatible CommandCenter™ or GreenStar™ Display that communicates on the machine CAN Bus. SAR is not compatible with every machine equipped with a Modular Telematics Gateway (MTG). (Refer to specific machine Operator’s Manual for detailed SAR information.
Operating—Service ADVISOR™ Remote PROOF If the message is cancelled, the user can access the page by selecting the Menu button and then Remote Software Updates. PC8663 —UN—29APR15 MENU button PC12671 —UN—21JUL10 Download Updates On the Remote Software Updates page, the operator can either reject (A) or download (B) the new software. Pressing the Download Software (B) button will start the download process. This process will continue in the background and normal machine operation can continue.
Once the software has been downloaded and it is ready for installation, a message will appear on the display. Press the accept button to go to the Remote Software Updates page. Software installation can take up to 40 minutes. Pressing the cancel button enables you to update the software at a later time if desired.
70B-4 PC12672 —UN—28JUN10 PC13582 —UN—09MAY11 PC12857 —UN—07SEP10 CAUTION: Some vehicle functions, including lights, may become inoperable during reprogramming. To avoid injury, ensure the vehicle is in a safe location and configuration before reprogramming. Do not reprogram near public roadways or in active work sites. PROOF On the Remote Software Updates page, press the Install Software button to begin the installation process.
Operating—Service ADVISOR™ Remote PROOF Troubleshooting — Reprogramming Symptom Problem Accessory Power Lost Engine started or key turned off. Voltage Low The system voltage is too low to Turn off or remove accessories that proceed with the software installation. are unnecessary. Communication Fault Remote Software Updates button is not on display. The software installation cannot be completed because of a communications fault. Cannot access Remote Software Updates page on the display.
Operating—Service ADVISOR™ Remote IMPORTANT -- READ CAREFULLY: THIS SOFTWARE LICENSE AGREEMENT IS A LEGAL CONTRACT BETWEEN YOU AND THE LICENSOR ("LICENSOR") IDENTIFIED BELOW AND GOVERNS YOUR USE OF THE SOFTWARE DELIVERED TO YOUR MACHINE (THE “MACHINE”).
Operating—Service ADVISOR™ Remote 9. Compliance with Law. You agree that you will use the Software in accordance with United States law and the laws of the country in which you are located, as applicable, including foreign trade control laws and regulations. The Software may be subject to export and other foreign trade controls restricting re-sales and/or transfers to other countries and parties.
Operating—Service ADVISOR™ Remote 16.2 Limitation of Liability for Users Residing in European Economic Area Countries or Switzerland. not be liable for damages caused by a slightly negligent breach of a non-material contractual obligation. (b) The aforesaid limitation of liability shall not apply to any mandatory statutory liability, in particular, to liability under the German Product Liability Act, liability for assuming a specific guarantee or liability for culpably caused personal injuries.
Operating—Service ADVISOR™ Remote PROOF Europe John Deere European Technology and Innovation Center Strassburger Allee 3 67657 Kaiserslautern, Germany Federal Republic of Germany Kaiserslautern, Germany Other The John Deere entity identified for the location of your Machine on www.JDLink.com. The John Deere entity identified for the location of your Machine on www.JDLink.com. The John Deere entity identified for the location of your Machine on www.JDLink.com.
Specifications PROOF • Fuse recommendations—The device should be Electrical Specifications protected with a 10A fuse maximum. Modular Telematics Gateway and Satellite Module • Input Voltage—The voltage range for switched and unswitched power 9-32VDC.
Index C Components ............................................................... 40-1 Cellular, GPS, and Wireless Antenna ..................... 40-2 MTG ........................................................................ 40-1 Satellite Antenna..................................................... 40-3 Satellite Module ...................................................... 40-3 Wireless Antenna.................................................... 40-3 Connectors MTG Antenna Connections..................
Index PROOF PROOF Index-2 062816 PN=2
www.JohnDeere.com/TechInfoStore • Call 1-800-522-7448 • Contact your John Deere dealer Available information includes: • PARTS CATALOGS list service parts available for your • • • PROOF machine with exploded view illustrations to help you identify the correct parts. It is also useful in assembling and disassembling. OPERATOR’S MANUALS providing safety, operating, maintenance, and service information. TECHNICAL MANUALS outlining service information for your machine.
John Deere Service Literature Available PROOF PROOF SERVLIT-2 062816 PN=42
That’s why we maintain a large and varied inventory—to stay a jump ahead of your needs. The Right Tools Precision tools and testing equipment enable our Service Department to locate and correct troubles quickly . . . to save you time and money. DX,IBC,A -19-04JUN90-1/1 TS101 —UN—23AUG88 We help minimize downtime by putting genuine John Deere parts in your hands in a hurry.
John Deere Service Keeps You On The Job PROOF PROOF IBC-2 062816 PN=44
John Deere Service Keeps You On The Job PROOF PROOF IBC-3 062816 PN=45
