U2 (International Version - S92P) Product Manual Printed Version 2021/04/08 v1.1 Reviewed By: He Yuan Announcement JMGO is committed to continuously improving both product performance and functionality. The images and function descriptions in the product manual are subject to product and factory presets. JMGO reserves the right to improve the functionality and human-machine interface (HMI) outlined in this manual without prior notice. The actual product should take precedence.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (2) Class B Device Warning Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
(1) cet appareil ne doit pas causer d'interférences nuisibles. (2) cet appareil doit accepter toute interférence, y compris les interférences pouvant entraîner un fonctionnement indésirable. (2) Canadian 20cm RF Exposure Statement (only add the following statement if the product is used >20cm away from the body) The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure.
Battery Safety Warning The remote control contains a built-in rechargeable battery. Observe the below safety guidelines. Do not disassemble, hit, squeeze, or throw into a fire. Do not continue use in case of severe malfunction. Do not expose to high temperatures. Do not use if battery has become immersed in water. Replacing the battery with another of the wrong type may result in explosion. Ensure that used batteries are disposed of carefully.
Chairman: 一. Scope of Delivery Projector Body x1 Power Cord x1 Remote Control x1 Remote Control Charging Cable x1 Grommet Holder x2 Product Manual & Three Guarantees Service Card x1 *Note: Thank you very much for purchasing this JMGO product. Please check the items received against those listed on the scope of delivery. If the items received are not the same as the scope of delivery, please contact JMGO customer service as soon as possible. 二.
1. Infrared sensor 2. Smart photosensitive sensor 3. Full-range speaker 4. Tilt-Adjustment Foot 1. Eye Protection Motion Sensor 2. Lens 3.
1. Power socket 2. LAN 3. OPTICAL 4. HDMI 2 5. HDMI 1 (ARC) 6. SERVICE 7. USB Port 1. Air inlet (do not cover) 2. USB Port 3.
1. Lifting Bracket 2. Mounting screw hole 3. Fall protection mounting hole 1. Flashing White Light: Standby mode 2. Solid White Light: Powered on 3.
4. Solid Blue Light: Bluetooth speaker successfully connected Supported Devices 1. TV Stick 2. USB 3. Hard Disk 4. Game Console 5. Microphone (JMGO only) 6. Set-top box 7. Speaker 8. Xbox 9. Switch 10. PlayStation Projection Distance and Image Size This product uses a fixed-focus lens with a fixed image size of 100 inches. Size: 100 inches Display length * width (in): 87*48.
*Note: The distance between the rear plane of the product and the screen surface should be around 9.5in (24cm) to display a 100-inch screen. 三. Primary System Functions 1.
Once a source is connected, select the corresponding button on the homepage to enter the external source. You can also select a source from Settings > Source, or by pressing the Source button on the remote control. 2. Settings You can enter the settings panel by selecting the Settings button from the bottom of the homepage, or by pressing the Settings button on the remote control. 1) System Update You can check or update the system version from Settings > System > Update Version.
Online Update: Head to Settings > System > Update Version. The system will automatically detect if your software is up-to-date. You will receive a prompt if the software is already the latest version. If your software is out-of-date, you will be asked if you wish to update it. Local Update: Download the software update package from the JMGO website, copy the file to the root directory of a hard disk or USB, then insert the hard disk or USB into the USB port on the projector body.
3) Audio Settings Settings > Audio > Audio Modes The product includes 4 different audio modes. These are Standard, Music, Film, and Sports. You can select the mode that best suits your preference.
4) USB Storage Devices This product can automatically identify USB storage devices. After inserting a USB device, simply follow the system prompts.
This product also supports manual switching between video sources. To switch to another video source, select Settings > Source > Local/HDMI. Alternatively, return to the homepage and select the corresponding source button to enter an external source.
5) Brightness Users can adjust the brightness of the projector lens manually or through the Smart Brightness function. The system automatically detects changes to the ambient light and adjusts the brightness accordingly. Settings > Projection Settings > Brightness > Smart Brightness/Custom a) Smart Brightness: Automatically adjusts brightness in accordance with ambient lighting.
b) Custom: Manually adjust the brightness with the keys on the side of the remote control. 下方线稿右侧为国内系统的页面,请注意替换 6) Eye Protection Feature This product includes a smart motion sensor designed to protect the user’s eyes. Settings > Projection Settings > Eye Protection(注意红字路径有修改,请按此修改) When this function is enabled, the smart sensor automatically cuts power to the projector lens when it detects that someone is too close. This helps prevent damage to the human eye.
7) Bluetooth Remote Control(本设备没有蓝牙语音,这个按键是 hdmi 信号源键。)
Screenshot Button Power Voice Control Direction Pad (Up/Down/Left/Right) Enter Return Home Menu Shortcut Settings Brightness Up Brightness Down Volume Up Volume Down LED Indicator Operation Press Press Function Turn the device on or off. Activate near-field voice control. Press Move the cursor, or select a direction. Press Press Press Press Press Press Press Press Press Press Confirm a selection. Return to the previous menu. Return to the home screen. Open the application menu. Open the shortcut menu.
will automatically attempt to pair and connect. If the pairing is successful, the projector interface will display the corresponding prompts. ⚫ If the indicator light turns off and there are no prompts on the screen, the pairing has failed and you will have to try again. ⚫ If you were unable to pair the remote control during initial setup, you can do so manually within the first 5 minutes of startup. The name of the Bluetooth remote control on the pair screen should be RemoteControl.
Note: JMGO regularly releases software updates as continuous maintenance services. We may push software updates without prior notice to ensure users can enjoy up-to-date experiences and services. b) Local Update: Download the software update package from the JMGO website, copy the file to the root directory of a hard disk or USB, then insert the hard disk or USB into the USB port on the projector body. Head to Settings > System > Update Version, then select Local Update.
2. Screen Share To use the screen share function, select the Screen Share button from the homepage, then follow the prompts to connect a device to the projector.
3. JMGO FUN To control the product through the JMGO FUN app, select the JMGO Fun button from the homepage, then follow the prompts to download JMGO FUN from the App Store or JMGO Official Website. You can download "Fun Control" from your mobile phone Appstore or, you can also find from our website (http://en.jmgo.com/remote.html) Make sure that your mobile phone and JMGO projector both are on the same Wi-Fi network Launch "Fun Control”, then the projector will automatically discover the application 4.
四. Environmental Protection This Environment-Friendly Use Period (EFUP) label indicates that there is a 10 year period before hazardous substances contained in this device are likely to leak out during normal use, causing possible harm to health and the environment. During normal use conditions, there will be no leakage or sudden change of hazardous substances, no serious pollution to the environment, and no serious damage to people or property.
reporting requirements of GB/T 26572-2011, and there is no readily available industry alternative that meets the environmental protection requirements of the China RoHS. Component Name Projector Body Remote Control Wiring Packaging Material Lead (Pb) Toxic and or Hazardous Substance or Elements Hexavalent Polybrominated Polybrominated Mercury Cadmium Chromium Biphenyls Diphenyl (Hg) (Cd) (Cr (VI)) (PBB) Ethers (PBDE) X O O O O O X O O O O O O O O O O O O O O O O O 五.
After the position of the projector and screen installation has been determined, tear off the protective paper from the grommet holder, attach the holder to the front foot, then paste to the tabletop. *Ensure that the grommet holder fits in place with the outer contour of the front foot. Pull out the lifting bracket beside the rear foot, then push it onto the wall surface. Mark the position on the wall surface, tighten the screws again, then note the relative position between the projector and the wall.
The validity period is calculated from the date of purchase, or the date of receipt of the package. If the product experiences a performance failure, the package must be returned within 30 days. The projector is guaranteed for 2 years. b) Non-European Region The validity period is calculated from the date of purchase, or the date of receipt of the package. If the product experiences a performance failure, the package must be returned within 30 days. The projector is guaranteed for 1 year.
components. 2) When seeking a return or replacement, please return all provided accessories as well (including but not limited to product accessories, gifts, warranty cards, manuals, etc.). 3) Tip: To ensure a smooth return or replacement process, we recommend that you keep the outer packaging, accessories, and other gifts provided with the products for 30 days from the date of receipt.
* If you did not receive a purchase order, please provide a copy of the purchase voucher. Contact Information Name: Phone: Address: *Replaced and repaired products will be returned to this address. Please ensure your details are filled in correctly. Green dotted lines serve as a separator. Dotted lines are not printed.