Users Manual

ManualsBrandsJLT Mobile ManualsElectronicsWiFi SOM Modular

MS-01 SOM

All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI.

Page 1

1. WiFi and Bluetooth

MS-01 Integrated Qualcomm WCN3990 to support WLAN 2x2 802.11a/b/g/n/ac with DBS

and 160 MHz, Bluetooth 5.0.

◼ 2 × 2 802.11ac with MU-MIMO

◼ DBS support

◼ 160 MHz bandwidth support

◼ Bluetooth 5.0

1.1 WLAN RF Characteristics

1.1.1 2.4 GHz WLAN Transmitter Characteristic

Parameter

Test

Conditions

Typ

Unit

1 Mbps DSSS (b) TX

Output power

1 Mbps BPSK 802.11(b) Mask

Compliance 35% EVM RMS power over

TX packet, 20 MHz

18 +/-

1.5

dBm

11 Mbps DSSS (b) TX

Output power

11 Mbps CCK 802.11(b) Mask

Compliance 35% EVM RMS power over

TX packet, 20 MHz

18 +/-

1.5

dBm

6 Mbps OFDM (g) TX

Output power

6 Mbps BPSK 802.11(g) Mask Compliance

-5 dB EVM RMS power over TX packet, 20

MHz

16 +/-

1.5

dBm

54 Mbps OFDM (g) TX

Output power

54 Mbps 64-QAM 802.11(g) Mask

Compliance -25 dB EVM RMS power over TX

packet, 20 MHz

14 +/-

1.5

dBm

MCS0 OFDM (n) TX Output

power, 20 MHz

6.5 Mbps BPSK 802.11(n) Mask Compliance -5

EVM RMS power over TX packet, 20 MHz

16 +/-

1.5

dBm

MCS7 OFDM (n) TX

Output power, 20 MHz

65 Mbps 64-QAM 802.11(n) Mask

Compliance -27 dB EVM RMS power over TX

packet, 20 MHz

13 +/-

1.5

dBm

MCS0 OFDM (n) TX

Output power, 40 MHz

13.5 Mbps BPSK 802.11(n) Mask Compliance

-5 dB EVM RMS power over TX packet, 40

MHz

16 +/-

1.5

dBm

MCS7 OFDM (n) TX

Output power, 40 MHz

135 Mbps 64-QAM 802.11(n) Mask

Compliance -27 dB EVM RMS power over TX

packet, 40 MHz

13 +/-

1.5

dBm

Summary of content (12 pages)

PAGE 1
MS-01 SOM ` 1. WiFi and Bluetooth MS-01 Integrated Qualcomm WCN3990 to support WLAN 2x2 802.11a/b/g/n/ac with DBS and 160 MHz, Bluetooth 5.0. ◼ ◼ ◼ ◼ 2 × 2 802.11ac with MU-MIMO DBS support 160 MHz bandwidth support Bluetooth 5.0 1.1 WLAN RF Characteristics 1.1.1 2.
PAGE 2
MS-01 SOM ` 1.1.2 2.4 GHz WLAN Receiver Characteristic Parameter 1 Mbps DSSS (b) Rx Sensitivity 11 Mbps DSSS (b) Rx Sensitivity 6 Mbps OFDM (g) Rx Sensitivity 54 Mbps OFDM (g) Rx Sensitivity MCS0 OFDM (n) Rx Sensitivity MCS7 OFDM (n) Rx Sensitivity MCS0 OFDM (n) Rx Sensitivity MCS7 OFDM (n) Rx Sensitivity 802.11b RX Overload Level 20MHz 802.11g RX Overload Level 20MHz 802.
PAGE 3
MS-01 SOM MCS9 OFDM (ac) TX Output power, 40 MHz MCS0 OFDM (ac) TX Output power, 80 MHz MCS9 OFDM (ac) TX Output power, 80 MHz 180 Mbps 256-QAM 802.11(ac) Mask Compliance -32 dB EVM RMS power over TX packet, 40 MHz 29.3 Mbps BPSK 802.11(ac) Mask Compliance -5 dB EVM RMS power over TX packet, 80 MHz 390 Mbps 256-QAM 802.11(ac) Mask Compliance -32 dB EVM RMS power over TX packet, 40 MHz 11 +/1.5 dBm 16 +/1.5 dBm 11 +/1.5 dBm All rights are reserved by USI.
PAGE 4
MS-01 SOM ` 1.1.4 5 GHz WLAN Receiver Characteristics 1.
PAGE 5
MS-01 SOM ` OEM/Integrators Installation Manual Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4. For FCC Part 15.
PAGE 6
MS-01 SOM ` Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 7
MS-01 SOM ` This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna.
PAGE 8
MS-01 SOM ` This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed with 20 cm is maintained between the antenna and users in mobile or fixed applications. 2) The Antenna for Module (MS-01) is Non-detachable and the maximum antenna gain allowed for use with this device is 0.0 dBi.@2.4GHz band & 2.3dBi@5GHz band. 3) The transmitter module may not be co-located with any other transmitter or antenna.
PAGE 9
MS-01 SOM ` Antenna Trace Design WLAN chain1/BT Top layer WLAN chain0 Top layer The Land Pattern and Dimensions should be compliance with USI's Standard PCB Design. The characteristics of products may vary depending on the pattern drawing method, grounding method, land dimensions, land forming method of the NC terminals and the PCB material and thickness. Therefore, be sure to verify the characteristics in the actual set. When using non-standard lands, contact Universal Global Scientific Industrial Co.
PAGE 10
MS-01 SOM ` Dipole Antenna All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI.
PAGE 11
MS-01 SOM `IFA Antenna: USI uses various test mode programs for test set up which operate separate from production firmware. Host integrators should contact USI for assistance with test modes needed for module/host compliance test requirements. The MS-01 modular transmitter is only FCC authorized for the specific rule parts (i.e.
PAGE 12
MS-01 SOM ` RSS-247 Section 6.4 (5) (6) (for local area network devices, 5GHz) The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology.