JLT6012A Quick Start Guide JLT6012A JLT Mobile Computers AB Head Office: Isbjörnsvägen 3, SE-352 45 Växjö, SWEDEN Sales Office: Medborgarplatsen 3, Plan 8, SE-118 26 Stockholm, SWEDEN Phone: +46 470 53 03 00 Fax+46 470 445 29 Email: info@jltmobile.
First start Android operating system is preinstalled on the unit. Follow instructions and steps given to complete the user setup. See section “Maintenance” for SIM-card installation. Touch Screen JLT6012A is equipped with a Projected Capacitive Touch screen. Also called PCT or PCAP. The touch screen is calibrated from factory and needs no further calibration. It has a resistant glass surface that can be cleaned with a damp cloth, ordinary soap or hand-dish washing fluids.
Interfaces Connectors From left to right: • • • • • • • • • WWAN Main, SMA GNSS, SMA WWAN Aux, SMA USB2 x2, USB type A Ethernet, RJ45 USB3.1, OTG, ADB, Display, USB type C USB3.1, USB type A RS232C, configurable 5V supply on pin1/9, D-Sub-9 Isolated Power input, 9-72VDC, nominal input voltage 12-60VDC – Pin 1 = Positive – Pin 2 = Remote On/Off – Pin 3 = Power Ground Power cable Connect cable as shown in the picture below.
Power Input and UPS The unit is equipped with an isolated wide range 9-72VDC input. Nominal input voltage 12-60VDC. If power is lost or switched off, the unit will switch to the UPS-battery to perform a controlled system shutdown. Battery and remote operation are configurable in JLT Control Panel application. Remote input is recommended to utilize to automatically power on and off the unit. Typically connects to a vehicle ignition switch. No additional grounding of unit is normally required.
Mounting Cable Strain Relief and Rubber Sealing Plugs Use included cable ties to attach cables to the strain relief plate. Install rubber sealing plugs to unused ports. JLT provided Mounting Kits: RAM® RAM® Mount -> Computer: Use included screws and washers. Usage of thread locking products like Loctite® is recommended. Mounting with other brands and parts When mounting a JLT unit to a VESA bracket, use M6 screws with correct length.
Important: The vehicle computer and bracket must be firmly secured to a surface that can support the vehicle computer´s weight and include optional accessories such as keyboard and scanners. Computer weight = 2.9 kg or 6.4 lb Keyboard mount An accessory keyboard mount is available from JLT that mounts towards the two M6 screw holes on each side. Fasteners are included with the mount. If other fasteners or screws are being used the depth of mounting holes are maximum 8mm.
Wireless Communication WLAN: 802.11 ac/a/b/g/n 2x2 Dual Band MU-MIMO Dual Mode Bluetooth 2x Integrated Antennas 2.4Ghz / 5Ghz NFC Optional: WWAN: 4G/3G, HSPA+, UMTS, LTE GNSS: GPS, Glonass, Galileo, BeiDou See section “Maintenance-Service lid overview” for SIM-card insertion. For best performance, make sure no antennas are obstructed, especially by conductive material such as any metal. The NFC are for close range >10mm, make sure it’s physically accessible when mounting unit.
Maintenance Battery Replacement • • • • Unscrew the six Torx 10 screws. Lift the lid and gasket. Lift the battery and unplug cable. Mount battery in reverse order make sure battery and gasket are in correct position.
LED indicators and Ambient light sensor LED, 1 1. Green, slow blink every 10 sec. Power is connected, unit is turned OFF 2. Green, Constantly lit Power is connected, unit is in normal operation 3. Orange, Constantly lit Unit is running on battery, preparing shutdown 4. Orange/Green alternately A button is pressed LED, 2 1. Off WiFi, no connection 2. Orange WiFi is connected, WiFi level 1-3 3.