Specifications

RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC
Functions
1. Frequency band: FM88.1-108MHz(Receive)
VHF 108-136MHz(Only AM receive)
VHF 136-174MHz(RX)&144-148MHz(TX)
UHF 400-520MHz(RX)&420-450MHz(TX)
2. Working mode: Frequency mode/Channel mode
3. FM Radio
4. Dual standby
5. 50 CTCSS/105 DCS
6. RX CTCSS/DCS , TX CTCSS/DCS can be set individually
7. TOT
8. Voice encryption(Frequency Hopping)
9. Frequency Step: 2.5K/5K/6.25K/10K/12.5K/20K/25K/50K
10. Battery saving
11. Reverse Frequency / Talk around
12. VOX
13. Busy channel lockout
14. Low battery alert / Voltage display
15. Automatic backlight
16. Channel display: Frequency/Channel/Channel name
17. Scan: Time/Carrier/Search
18. Frequency mode: Frequency difference+/Frequency difference-
19. Frequency mode: Frequency difference range: 0-99.9995MHz
20. Frequency mode: Edit/Save channel specs
21. 256 memory channels
22. Emergency
23. Frequency scan
24. DTMF
25. GPS (optional)
26. Boot interface customization
27. PC Programming
28. Wireless programming via Bluetooth(optional)
Keypad description
1. Keypad function
P1
Short press: Switch A/B band
Long press: In channel mode, switch channel display mode
P2
Short press: Switch frequency mode and channel mode
Long press: Turn on/off ANI name display function
Functional keypad
Select/confirm [ ]
Enter Menu, then select option in menu list
[ ]Long press to quickly change menu option, in Scan
mode, change scan direction
[ ]Long press to quickly change menu option, in Scan
mode, change scan direction
[ ]In the input state, clear the information that has been
input
Numeric keypad
Input information while in programming menu or input
non-standard CTCSS/DCS if need[ ]key
Short Press: Switch Reverse Frequency / Talk around
/Normal mode
Long press(Over 2 seconds): Active frequency/channel
scan[ ]
Short press: DTMF edit. Use * key to end if less then 6
digits
In FM mode, scan FM
Long press: Lock/unlock keypad
[SOS] Key
Long press to enter this function, short press to exit this
function
Power/Volume on-off
clockwise rotation: Power on/Volume+
Anticlockwise rotation: Power off/Volume-
Status Indicator
TX- Red light
RX- Green light
External Jack
Earpiece or programming cable
Side key 1(PTT): Short press to exit SOS mode while in
SOS mode
Side key 2: Set functions via programming software
Side key 3: Long press to active MONI mode. Set func-
tion for short press via programming software
2. Muti keys function
1750Hz Tone: PTT + MONI
DTMF: PTT+ numeric keys+ to transmit DTMF 0-9,
ABCD*#
Screen display and Menu list
Screen display
Icon definition
Screen display
Menu
Menu List
Menu operation
1) Press ，then enter menu via up/down key.
2) Press again to enter the menu function
3) Select option via up/down key.
4) Press to confirm and back to main menu
5) Press to exit menu and back to normal working
mode.
Note: Step, TX power, W/N band, CTCSS/DCS,
frequency different etc. only set valid in frequency mode.
Other function description
1. Dual PTT
Set side key2 as PTT-B, press PTT to transmit A band,
press PTT-B to transmit B band.
2. AM Mode
108-136Mhz, AM mode receiving
3. Scan mode
TO/CO/SE Mode
TO : Time scanning, the walkie-talkie pauses scanning
when it detects a signal, and after staying stopped for
about 5 seconds, the walkie-talkie will continue scanning
even if the signal is still there.
CO: Carrier scanning, the two-way radio pauses scanning
when a channel is detected and keeps it on the same
frequency until the signal disappears. There is a 2 second
delay between the disappearance of the signal and the
resumption of scanning to allow time for the response to
begin transmission.
SE: Search scanning, the walkie-talkie exits scanning when
it detects a signal and stays at this frequency.
FM function
1)Turn on FM function, the screen will display current
FM frequency
2)Press to change FM frequency, or input via
keypad(88.1-108MHz); Press # key to scan FM frequency
automatically in FM mode
3)Adjust volume via Power/volume knob
4)Press FM key again to exit FM mode
Note: FM function need to be set in side key customized
setting.
Frequency scan
Scan other radios’ CTCSS/DCS and frequency to make
a contact.
After defining the side key function as a frequency scan
function, turn it on through the side key. This function
can scan the frequency of U/V/200M/350M, and switch
the frequency band to be scanned by the [P1] key. After
scanning the frequency, it will continue to scan
CTCSS/DCS. If there is no CTCSS/DCS, the screen will
display 'NONE' and end the scan. At this time, the
scanned data can be saved to the designated channel
through the [ ]key and the frequency scan function can
be launched. Or through[ ]or[ ]to start the next
frequency scan.DTMF
A. DTMF encode
Quick transmitting Encode: In transmitting status, press
digit keys, [ ] *, # to transmit DTMF encode 0-9,
ABCD*#. Press key to continuously encode transmitting
and release to end encode transmitting.
Transmitting encode after editing: In standby mode, press
[#] key to enter DTMF edit menu, input 0-9,ABCD*#, if
less 6 digits then press [#] as ending. Done editing, press
PTT to transmitting DTMF. In edit mode press [ ]to
delete encode, then press [ ] to exit DTMF edit mode.
B. DTMF Decode
ANI Name Display
To indicator which radio is transmitting. 60 group names
can be selected.
50 groups name are radio 1 to radio 50. The rest of 10
group names can be edited via programming software.
GPS function
Press [ ]or [ ]to enter the GPS positioning interface.
At the same time, you can switch the coordinate display
mode and the image mode. It also has the backtracking
function. You can store the starting point position in
advance, and you can view the direction and distance to
the current position in real time to ensure that you won't
get lost in the wild.
Wireless programming via Bluetooth
AM Mode
FM Mode
Bluetooth turn on
GPS
GPS turn on
Transmitting power
Indicates the amplitude of audio transmission when transmitting,
and the signal strength when receiving
Icon Description
CTCSS display
DCS display
Frequency difference +
Frequency difference -
Dual standby
VOX
Reverse Frequency
Talk Around
Narrow Band
Battery level display
Keypad lock
High Power
Low Power
Tone while DTMF transmitting
4 R-CTCSS 接收模拟亚音
OFF None DCS
67.0HZ,…,2
54.1HZ
Standard CTCSS.
Input standard
or nonstandard
CTCSS via keypad.
5 R-DCS 接收数字亚音
OFF None DCS
D023N,…,D7
54I
Standard DCS
None CTCSS
6 T-CTCSS 发射模拟亚音
OFF
67.0HZ,…,2
54.1HZ
Standard CTCSS.
Input standard
or nonstandard
CTCSS via keypad.
7 T-DCS 发射数字亚音
OFF None DCS
D023N,…,D7
54I
Standard DCS
High Power Transmitting
Lower Power Transmitting
Off Battery saving
Off Battery saving
8 VOICEPRI
语音加密 OFF
Encryption 1
Encryption 2
Encryption 3
Encryption 4
Common name List
9 CH-MAME
信道名称
10 TXP 发射功率
HIGH
LOW
11 SAVE 省电模式
OFF
1
2 Normal saving
3 Super saving
12
POGER
通话结束提示音
OFF
Turn off
ON
Turn on
13 TOT 发射限时
30,60,…
480S
The number is
from 30 to 480s,
and the maximum
time for PTT
transmission is
indicated in 30s steps
14 VOX 声控发射
OFF
Turn off VOX
function,
transmitting
without PTT pressing
1,2,… 9
15 W/N 信道带宽
WIDE Wide mode
NARR Narrow mode
Activate the sound
pressure intensity of
voice control, level 1
is the most sensitive
16 VOICE 语音提示开关
OFF
ON
17 BEEP 哔音开关
OFF
ON
18 LANGUAGE 菜单语言
ENGLISH English
Chinese Chinese
19 BCL 繁忙锁定
OFF OFF
ON ON
20 SC-REV 扫描模式
TO
Time scanning,
the walkie-talkie
pauses scanning
when it detects
a signal, and after
staying stopped for
about 5 seconds,
the walkie-talkie
will continue scanning
even if the signal is
still there.
CO
Carrier scanning,
the two-way radio
pauses scanning when
a channel is detected
and keeps it on the
same frequency until
the signal disappears.
There is a 2 second
delay between the
disappearance of the
signal and the resumption
of scanning to allow time
for the response to begin
transmission.
SE
Search scaning,
the walkie-talkie
exits scanning
when it detects
a signal and
stays at this
frequency.
21 PF2
侧键 2 短按功能设
置
22
PF2 LONG
PRESS
侧键 2 长按功能设
置
23 PF3
侧键 3 短按功能设
置
24 ABR
自动背光灯时间设
置
ON
5S,10S...
3Min、
Time between the
background light
ON to automatically OFF.
25 OFFSET 频差频率
00.000,…,9
9.995
In frequency mode, the
difference between the
transmitting and receiving
frequencies
26 SFT-D 频差方向
OFF
In frequency mode, turn
off the difference between
the transmitting and rece-
iving frequencies
+
In frequency mode, the TX
frequency=RX frequency
plus frequency difference
In frequency mode, the TX
frequency=RX frequency minus
frequency difference
-
Turn off voice prompt
Turn on voice prompt
Turn off operation prompt
Turn on operation prompt
Background light is always on
27 SCAN CTCSS 扫描模拟亚音
28 SCAN DCS 扫描数字亚音
29
CDCSS SAVE
MODE
扫描亚音频存储
ALL ALL
RX Receiving
TX Transmitting
30 POWER ON MSG 开机画面选择
LOGO Photo
VOL TAGE Battery voltage
31 ANI NAME 本机名称选择
NUM1…NUM60
32 S-CODE DTMF 信息码 1,2,3...15
33 DTMF CODE 上下线码
OFF Turn off
BOT
EOT
BOTH
34 DTMFST 侧音开关
OFF
DT-ST
ANI-ST
DTMF prompt when automatically
transmitting DTM
DT+ANI
DTMF prompt when automatically
transmitting DTMF and press key
to transmitting DTMF
35 AUTOLK 自动键盘锁
OFF
5S、10S、15S
36 SCAN ADD 信道扫描添加
37 TONE TONE 音
1000,1450,
1750,2100Hz
38 PTT-LT 发码附加延迟
0,100,…,10
00
Delay time before
automatic DTMF
transmitting
Control the time of menu
automatically exit
39
MENU EXIT
TIME
菜单自动退出时间 5,10,...60S
40 VOX DELAY 声控延时
0.5SEC.....
2.0SEC
41 RP_STE 过中继尾音消除 OFF
Due to the delay of the
repeater, noise appears
when receive instant signal.
No.1---No.50 radio. The radio name
of 51-60 can be set
Press PTT to transmitting DTMF
Release PTT to transmitting DTMF
No DTMF prompt when press key
to transmitting DTMF
DTMF prompt when press key to
transmitting DTMF
BOTH
Turn off auto keypad lock
Turn on the keypad timing
automatic lock function
OFF: Adjust to el
iminate the tail.
If want to ensure
if the repeater
is work or not,
set OFF.
1,2,3,4,5,
… 10S
42 RPT-RL 过中继尾音延时
OFF
OFF: Adjust the
length of time
the tail sound
appears, if not
needed, set it to
off.
1,2,3,4,5,
… 10S
43 ANI FUNCTION 身份码功能
OFF Turn off
ON Turn on
44 MDF-A A 段显示模式
FREQ
A band displays as
frequency in channel mode
,
CH
A band displays as channel
in channel mode
NAME
A band displays as channel
name in channel mode
45 MDF-B B 段显示模式
FREQ
B band displays as freq-
uency in channel mode
CH
B band displays as channel
in channel mode
NAME
band displays as channel
name in channel mode
In dual standby mode,
press PTT to transmitting
A band for cross-band TX/RX
A
In dual standby mode
press PTT to tra-
nsmitting B band for
cross-band TX/RX
After releasing the PTT,
the radio will send a
turn-off code to suppress
the instant noise of the
receiver.
After releasing the PTT,
the radio will send a turn-off
code to suppress the instant
noise of the receiver.
After releasing the PTT,
the radio will send a turn-off
code to suppress the instant
noise of the receiver.
B
48 STE 尾音消除
OFF
ON
49 AL-MOD 报警模式
SITE On-site Emergency
SOUND
CODE
50 GPS GPS 定位
OFF
ON
51 BLUETOOTH 蓝牙写频
OFF
ON
52 DISPLAY 接收时间显示
OFF
ON
53
RESET
恢复出厂设置
VFO
ALL
46 TDR 双频守侯
OFF Turn off
ON Turn on
In dual standby
mode, transmitting
current frequency band
47 TX-A/B
双守发射选择
OFF
Send emergency voice
Send emergency code
Turn off
Turn on
Turn off
Turn on
Turn off
Turn on
Menu back to factory
setting
Menu and channel back
to factory setting
Note: When entering the menu, take note of whether to set A band or B band.
NoMenu
List
Chinese
2nd menu
characters
Description
0 SQL 静噪等级
0,…,9
1 STEP 步进频率
2.50K
5.00K
6.25K
10.00K
12.50K
20.00K
25.00K
50.00K
2 MEMCH 信道存储 000,…,256
Indicate the
channel number
to be stored while
store channel. if ‘CH’
in front of number means
this channel already has
a channel parameter.
3 DELCH 信道删除 000,…,256
The lower the
level, the easier
it is to be disturbed,
the higher the level,
the worse the sensitivity.
Better set as medium.
In frequency mode, to change
frequency step
Delete the channelparameters of
the specified channel. If there
is no CH-
means that the channel has
no parameters and the operation
is invalid.
-1-
-2-
-3-
-4-
-5- -6-
-7- -8-
-9- -10-
-11- -12-
-13- -14-
-15-
■
FCC Compliance Statements:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR
RULES AND FEDERAL LAW.
■
Licensing Information
Use our radio in USA is subject to the rules & regulations of FCC. Changes
or modifications not expressly approved by our may void the user authority
granted by the FCC to operate this radio and should not be made. To
comply with FCC requirements, transmitter adjustments should be made
only by or under the supervision of a person certified as technically qualified
to perform transmitter maintenance and repairs in the private land mobile
and fixed services as certified by an organization representative of the user
of those services. Replacement of any transmitter component (crystal,
semiconductor, etc) not authorized by the FCC equipment authorization for
this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be
distributed is subject to government regulations and may be prohibited.
Important: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this device. Your radio is set up to transmit a regulated signal on an
assigned frequency. It is against the law to alter or adjust the settings inside
the radio to exceed those limitations. Any adjustments to your radio must
be made by qualified technicians.