Operation Instructions Product Name: Smart Bike Trainer (DJS‐003) Product Model: TY‐DJS003 Jinhua Unisky Tools Co., Ltd.
Catalogue Warning After‐Sales Service Disclaimer Spare Parts List Installation Instructions 1、Bike Confirmation 2、Assembly of Bike Trainer and Damper 3、Bike Installation and Debugging Smart Training Maintenance Common Fault and Eliminating Methods Product Specification Parameters FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
and prevent and avoid unnecessary accidents and injuries. ●Please replace and use our special quick release for the rear wheel of the bike before use, and carefully check whether all parts in the package are complete. ● Before use, please confirm that the product has been placed on firm ground, and the four‐foot pads on the feet touch the ground at the same time, to ensure that the product is stable and does not shake. ● Before starting the training, please make sure you are in good health.
shake the bike to avoid falling or damaging the bike. ● Please do not disassemble or convert this product by yourself. ● Please use the original spare parts. If there is any problem with this product, please contact the authorized dealer of UNISKY. After‐Sales Service The products shall provide three guarantees of product quality within one year from the date of sale. The specific implementation is as follows: 1.
consumers themselves. 6. Damage caused by flood, fire, earthquake and other irresistible natural factors Tip: For products not covered by the Three Guarantees, the dealer shall provide paid maintenance services, and the consumer shall bear all costs for maintenance, replacement of parts, transportation, etc.
B Power Adaptor 12V‐4A 1 Electromagnetic Coil C 1 Damper D Hexagon Bolt M8*95 1 E Lock Nut M8 1 F Flat Washer φ8 2 G ANT+ Receiver 1 Front Wheel Fixing H 1 Seat I Quick Release 1 J L‐Type Socket Spanner 2 Installation Instructions Step 1. Bike Confirmation Before using the bike trainer, please confirm the specification of the bike that you want to use. This product is suitable for 26", 28', 700C and 29" mountain bikes and road bikes. Step 2.
2‐1 Open the box and check all the parts and quantity according to the spare parts list. 2‐2 Put up the frame. 1)As shown in figure 1, put up the two A pipes of the bike trainer to the maximum position, place them on the working surface, and ensure that the movable pin of B cylinder slides into slot C.
3)As shown in Figure 3 above, hold the damper with the left hand and lift it slowly. Adjust the position of the screw hole of the cylindrical movable pin with the right hand, and then align the mouth of the adjusting screw with the screw hole of the cylindrical movable pin. Slightly lift the left hand to make the mouth of the adjusting screw completely align with the screw hole.
Note: during operation, hold the damper with one hand gently, and hold the cylindrical movable pin with the other hand to slide it from slot C to slot D. Pay attention to prevent hand injury during sliding! Step 3. Bike Installation and Debugging 1)Place the bike trainer on stable ground, and adjust the rotary knobs on both sides of the bike trainer so that the distance between the axle sleeve A and the axle sleeve B is greater than the length of the bike quick release, as shown in Figure 5.
3)Adjust the knobs on both sides to make the bike tire roughly in the middle of the roller, as shown in Fig. 6. The knobs on both sides should be tightened to prevent the bike from shaking easily, and then lock the two nuts on the screw rods on both sides for fixing. 4)Adjust the triangular knob clockwise to make the tire just touch the bicycle, and then tighten the triangle knob for a circle and a half turns to make the roller press into the tire tightly.
5)As shown in Figure 7, the standard front‐wheel stand is fixed under the front wheel of the bike to reduce the left and right wing of the front wheel and improve the comfort while riding.
Smart Training 1 Bike Trainer Pairing This bike trainer needs to be connected with external power supply before it can be used (When using PC, you need to plug the ANT+ receiver into the USB port of the computer). Take out the power adapter in the packing box, connect the DC plug to the bike trainer first, and then connect the power supply. When the power is connected, the power signal indicator on the damper is always on, and the ANT + signal indicator and Bluetooth signal indicator are flashing.
power and other items. The advantages of using mobile phones or tablets are simple, clear, and convenient. At present, the game video training mode is not supported on mobile phones. This product can also be connected to ANT + riding stopwatch for use. The specific operation methods of pairing and setting shall be according to the operation instructions of each brand. The subsequent operation can be carried out after confirming the connection.
Connect the bike trainer to power, insert ANT+ USB disk into computer SUB port to receive the data between the trainer and computer. 3. Click the downloaded APP Zwift, and enter in. Register it if you are new for the APP, after this, login. Or you could login directly if you have already had an ID. 4. Connect the trainer and the Zwift software. Click the controllable one to connect the trainer. 5. Choose the training type and riding route.
Maintenance The product can be folded for storage. Operation method: press down the two A pipes directly and tuck them in. Take care not to hurt your hands when folding and tucking. This product must be stored in a clean indoor environment that is dry, away from direct sunlight, fire, water, or other dangerous goods. Due to the circuit board structure inside the product, please only wipe the product with a clean cloth for cleaning.
Excessive body Check if the exposed counterweight wheel shakes and vibration during use if the knobs and nuts on both sides of the bike trainer are loose. Check whether the tire pressure of a bicycle is in normal condition. Note: If the fault still cannot be eliminated, please contact the authorized dealer of UNISKY for assistance.
Riders Adaptable Bike Mode Noise Level Casing Temperature Adaptable 26"、700C、28"、29." ≤68db(A‐Weight、1.5m、30Km/h) ≤75℃ Third‐party Zwift, Onelap, Strava, etc. Riding Platforms Adaptable Smart Devices ANT+ stopwatch, Computer, Tablet, Mobile phone, etc.