User's Manual

MATTERS NEEDING ATTENTION
SYSTEM CONNECTION METHOD
HOW TO USE THE MEMOREX MP3862
1. Handle
2. CD Door ON/OFF
3. Channel Selection
4. Function
5. Waveband
6. Auto Channel Selection
7. Standby
8. DBB
9. Volume
10. Play/Pause
11. Previous/Fast Reverse
12. Next/Fast Forward
13. LCD Display Window
14. Standby/Bluetooth Indicator
15. Remote Control Receiver
16. Mode
17. Programming (Time Setting)
18. Stop
19. Audio Input Port
20. Earphone Port
21. External AC Power Port
22. Battery Cover (bottom)
Power Supply:
AC 120V~,60Hz,17W or
DC 12V (8x1.5V “C” size,UM-2 batteries
Output Power: 1.5W+1.5W
Cd Playback Frequency Response: 31.5Hz-16kHz±3dB
CD SNR: ≥50dB
Cd Sampling Frequency: 44.1kHz
DAC Mode: 16 bit
Frequency Scope: FM: 87.5-108MHz AM: 530-1710kHz
Remote Control Distance: 8m
Remote Control Angle of Deviation: 30 degree
Bluetooth Reception Distance: 8m
Speakerphone Resistance: 4 ohm + 4 ohm
Dimensions: 350mm x 242 mm x 140 mm
Weight: about 1.69kg
The product’s specifications and design are subject to change without additional notice.
1. Programming Function: CD Mode
Under Stop Status, press Programming on remote controller, and LCD will display flickering P01 to enter
programming status as showed in Figure 4. Press Previous or Next or Number button on remote
controller
to select the song you want to program; then, press Programming again to save the song. In this case,
20
songs are available for programming at most under CD Mode, and 99 songs under MP3 Mode. After
such
programming, you can press Play to play the song in proper order as programmed, and LCD display is
showed in Figure 5. If you press Stop during programming process, it will stop programming and quit
from
programming status.
***Under programmed playing status, press Stop twice and then press Play, it will switch to Normal
Playing Status.
Time Setting:
Under Standby or any Start-up mode, press and hold Programming/Time Setting (17) till LCD displays
flickering 24H; then, release Programming/Time Setting (17) and press Previous (11) or Next (12) to
select Time Format (12H/24H). After that, please press Mode (16) to confirm such time format, and then
enter Time Setting interface. At this moment, Hour number will flicker, and you can adjust Hour Number
by pressing Previous (11) or Next (12). Later, you can press Mode (16) for confirmation. The same
operation shall prevail for setting Minute Number.
In addition, the above time setting method shall prevail for remote controller’s time setting.
11. When the product’s radio function is enabled:
a. Press Play/Pause to enable auto channel searching and save searched channel;
b. Press and hold Previous/Next to enable Manual Channel Searching and save searched channel;
press Previous/Next to adjust step frequency. For example, original reception frequency is 98.0MHZ,
and it will respectively change to 97.9MHZ and 98.1MHZ by pressing Previous/Next. Press Stop to
select a saved channel in proper order.
12. Press Content-/Content+ to select a saved channel.
When the product is not under CD Play Mode, previous programming will be canceled.
2. MP3 Content+/MP3 Content-
When MP3 disc is playing, press Content+, and it will skip to next content for play; press Content-, and it
will skip to previous content for play.
3. Number Button
1: During Playing, directly press a Number button to choose a song for play.
For example, if you want to No.26 song, you need press Number Button 2 and Number Button 6.
3. Mode Function of Remote Controller is the same with that of the product.
4. Function: Under start-up status, press Function to select different functions, including:
CD/MP3 Disc Function→Card Play→Radio→Audio Input→Bluetooth Function
7. Previous/Next (PREV/REW. NEXT/F.F): Press it to enable Previous or Next, Fast Forward or Fast
Reverse function.
Programming Status Display Programmed Playing Status Display
CD DISC OPERATION
Bluetooth Operation
Maintenance
1. Gently press Standby, and it will display HI under start-up status, and OFF under shutdown
status; press Function (4) and select CD Mode;
2. Open CD Door, and it will display OP; lay the printed CD Disc surface on CD Machine’s
Movement Shaft; then, close CD Door, it will reveal “---” and start reading the disc. LCD will show
relevant information. It will start playing the first song after displaying Total Song Number. 1s later, it
will display disc reading time from 0:01, and then display current song and playing time as showed
in Figure 2;
3. Press Play/Pause to stop playing, and press it again to start playing again. Under Pause status,
LCD will show flickering Play.
4. If you want to Pause, please press CD Stop (18).
5. During playing, press Next/Fast Forward (12) to skip to Next Song; press Previous/Fast Reverse
(11)
to skip to Previous Song;
6. During playing, press and hold Previous, and it will enable Fast Reverse. Then, you can stop at
where
you like. Similarly, press and hold Next, and it will enable Fast Forward. Then, you can stop at
where you like.
7. During playing, press Mode to enable Repetition Function, and repetition order is as follows:
Repeat A Single Song-Repeat the List-Repeat All Songs-Random Play-Cancel.
8. Under Stop status, press Programming/Time Setting (17) to enter Programming Status by using
the same
operation method as showed in Remote Controller Operation (1).
1. Gently press Standby, and it will display HI under start-up status, and OFF under shutdown
status; press Function (4) and select BT. Mode; in this case, Bluetooth is under Matching
Status with flickering blue indicator (14).
2. Start up mobile phone or other Bluetooth devices, and search the product’s Bluetooth
Device Name “BT-9237MUC”. If the software version is lower in mobile phone or other
Bluetooth Devices, Bluetooth password is required. Please input 0000 for successful matching,
and such blue indicator will keep ON;
3. After Bluetooth Matching, press and hold Mode (16) to quit from Bluetooth Matching; press
Play twice to enable Callback function;
4. After Bluetooth Matching, press Play to answer a call; press Play twice to refuse a call;
5. After Bluetooth Matching, after a call is answered, press Play to end the call;
6. Under Bluetooth Playing Status, press Play to enable Play/Pause function;
Remark: With 5 minutes after the product starts up, it will automatically enter Dormant State if
no Bluetooth matching is available, and the indicator will flicker slowly.
7. After Bluetooth Matching, press and hold Mode (16) to disconnect current Bluetooth
connection, and wait for the next matching and connection.
1. If the product gets very dirty, please firstly make a piece of soft cloth soaked with fresh water
or soap water and then wring it up to wipe the product’s body. Before you apply any chemical
cleanser, please firstly read relevant instructions. Please do not use alcohol or banana oil to
clean the product.
2. After a long time, the product’s laser lens may become dirty, which may cause playback
intermission. In this case, please use camera lens brush to gently wipe off dust, and then blow it
by using hair drier. Alternatively, you can use clean swab soaked with absolute alcohol to gently
wipe the laser lens, and then use another clean swab to dry it.
.
3. Please do not touch the disc’s data surface (silver surface) by hand so as not to cause sound
intermission during playing.
4. When the disc’s data surface gets very dirty, please wipe it off by using soft wet cloth and then dry
it up. It should be noted that, please straightly wipe it from center to outside, and do not rotate the
disc.
5. Never try to write or post any label on the disc.
.
3. Please do not touch the disc’s data surface (silver surface) by hand so as not to cause sound
intermission during playing.
4. When the disc’s data surface gets very dirty, please wipe it off by using soft wet cloth and then dry
it up. It should be noted that, please straightly wipe it from center to outside, and do not rotate the
disc.
5. Never try to write or post any label on the disc.
Fault
Description
Possible Reasons
Solutions
The product
cannot work.
Power plug is not well
connected.
Please well connect
the power plug.
The disc is not correctly
place.
Correctly place the
disc with printed
surface up.
The disc is not
compatible.
Replace the disc with
a compatible one.
The product
cannot play
music.
CD Door is not well
closed.
Please close CD Door
well.
Remote controller’s front
end is not rightly towards
its reception window.
Please make its
orientation right.
Battery is exhausted. Please replace the
battery.
Remote
Controller
cannot work.
Distance is extremely
long.
Please operate it
within valid distance.
Operation method is
wrong.
Please operate it
according to User’s
Manual.
It cannot
produce any
sound.
Volume is adjusted to the
minimum.
Increase the volume.
The Disc or laser lens
becomes dirty.
Please clean the disc
or laser lens.
Sound
Intermission
The disc is scratched or
curled up.
Replace it with a new
one.
The product
and remote
controller are
out of
control.
Power Supply is quickly
switched, and the system
program cannot be
rebooted.
Power it off firstly,
and then power it on 1
minute later.
TROUBLESHOOTING GUIDE
MP3862
Please carefully read this User’s Manual prior to first usage, and properly keep it for future
reference. Users are subject to User’s Manual, Warnings, Matters Needing Attention and the
following Safety Regulations.
Working Environment
1. Water and Moisture Do not use the product near water, including bathtub, sink, kitchen sink,
washtub, wet floor, swimming pool and the like.
2. High Temperature Do not use the product near any heat source, including radiator, heater or
other heating appliances.
3. Surface Please well place the product on flat surface.
4. Good Ventilation Please place the product with good ventilation condition so as to ensure
enough space for ventilation. Meanwhile, 10cm space shall be spared in the rear and on the top of
the product, and 5cm on both sides.
•Do not place the product on bed, carpet or other similar surfaces that may obstruct the opening for
ventilation.
•Do not place the product on book shelf or within cabinet or seal carrier, otherwise, ventilation effect
may be badly influenced.
5. Try not to allow any object or liquid to enter the product’s interior via ventilation opening.
6. Never place container with water in it on the product, e.g. Vase.
7. Moisture Condensation In the followings cases, moisture may be condensed on laser lens:
•Move from cold place to warm place.
•Heating system starts to work.
•The product is working in damp environment.
When moisture condensation happens to the product, it’s unable to work normally. In this case,
please stop using it for several hours, and then start to operate it again.
Power Supply
1. Power Supply The product can only apply the battery and AC power supply indicated in User’s
Manual or Outer Shell.
2. AC Power Line
•Please unplug AC Power Line by holding the plug, and try not to directly pull the power line.
•Please avoid touching AC Power Plug with wet hands, otherwise, it may cause electric shock.
•Please well place the power line at a fixed place so as not to tramp on it. Please do not apply any
power plug connected with extremely fine and long power line. If the plug is overloaded, fire or
electric shock may happen.
3. When the product needs to be left unused for a long time, please unplug AC Power Plug and
take out the battery so as to avoid any damage caused by the leakage of battery fluid.
******Network Source Disconnection Device: If Power Plug and Appliance Coupler are applied as
Disconnection Device, such device shall be favorable for easy and convenient operation.
Power Supply
1. Open the battery cover (24), and correctly install 8 batteries (UM-2 No.2) as indicated in battery
compartment. Then, please close the battery cover and unplug the power line (23).
2. AC Power Supply Operation
Connect one end of AC Power Line with the plug (23), and the other end 220V city power supply.
When the product is connected with power supply, standby indicator (14) will be ON, and it will
enter standby status. After AC Power Line (23) is correctly plugged, battery power supply will be
automatically disconnected.
Earphone Connection Method
You can listen to program available in the product via Earphone. Please insert Earphone into
Earphone Port (20), and built-in speakerphone will be automatically disconnected.
Audio Input
1. The product is able to amplify all external sound sources (including Mobile Phone, MP3 Player,
Walkman, CD and Radio etc.).
2. Gently press Standby and Function (4), and select AUX; LCD will display relevant AUX
information as showed in Figure 1.
3. Connect Audio Input Port (19) with External Source via Audio Input Cable, and then enable the
external source to realize sound amplification.
4. Adjust Volume (9) as you like.