WiFi IP CAMERA QUICK OPERATION GUIDE Note: Due to the continuous updating of the products and software,there may have some discrepancy between the operating guide and APP interface.All the instructions are subject to the actual operation interface.
Contents WiFi IP CAMERA ......................................................................................................... - 1 Service Guarantee ....................................................................................... 错误!未定义书签。 1. Introduction .............................................................................................................. - 4 2. Installation ...............................................................................................................
5.6.11 SD card plan recording ................................................................................ - 17 5.6.12 Device time setting..................................................................................... - 18 5.6.13 SD card setting ......................................................................................... - 19 5.6.14 Default setting .......................................................................................... - 19 6. Computer Browsing Access ..............
1. Introduction Thanks for buying YoLuke Security IP Camera. This manual describes all the parameters, functional structures,usage,common problems and solutions for the cameras in detail. This would help you know the camera quickly and use it easily. If you have any problems with our camera or confused in the settings, please contact with us, and we will provide technical support and service at the first time. 2.
3. SD Card Slot 4. APP Download Download APP “CamHipro” or “CamHi”in Google Play or Apple Store, or scan the QR Code to install.
Software Overview: Camhi Pro APP is a tool for managing network cameras, which can realize the functions of monitoring the images of network cameras on the LAN and the Internet on the mobile phone.
Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 5.2 Connect to IP Camera Hot-Spot and then Configure Wi-Fi Go to your cell phone’s Wi-Fi Setting -- search Wi-Fi signals -- connect the Wi-Fi. The name of Wi-Fi Hot Spot is the UID on the camera (Wi-Fi name:IPCAM-900139) Camera default Wi-Fi Hot Spot password: 01234567 Remark: Only when the mobile phone is 3-5 meters away from the camera can the hot spot signal be detected,please close the mobile data when connect the camera Hot Spot.
5.3 Add Camera Add your camera to ‘CamHipro’ APP follow the steps of the below pictures. Step 1 Step 2 Step 3 5.
Step 1 Step 2 Step 3 Step 4 5.5 Connect the Camera by Search Nearby Devices A） Connect the camera to the power supply and the camera would turn into self-test mode, which would take about 15 seconds. Open the ‘CamHipro’ APP. B） Add the camera by Search Nearby Devices follow the below steps. Note: 1.Please make sure that the camera has been connected to router’s Wi-Fi. 2.Please make sure that your cell phone connects the same Wi-Fi as the camera connected. 3.
Step 4 Step 5 Step 6 - 10 -
5.6 Mobile APP Function Introduction 5.6.1 Micro SD Card Video files playback and download Opps:if you download the recorded video files from pc,then the files can only be played in hiplayer.
5.6.2 Local files, device list and add other new camera Click click to view the local file of different cameras.；click to add a new camera. 5.6.
Remarks: HD is a higher-definition display effect than SD (recommended to use when the network is good)
Auto Cruise Function: Number 1-16 means 16 points you want to set up Adjust the camera rotation to the first point you want to monitor on the app; input "1" and Setting; Adjust the camera rotation to the second point you want to monitor on the app; input "2" and Setting; ……until set up 16 points…… After you set up 16 points, input "41" and transfer. The camera will auto cruise. Input "41" and Setting, auto cruise will stop 5.6.4 Change password Click “Change Password” to modify the password.
5.6.6 Alarm management and notification Recording and alarm, default recording all day;APP push is off by default;Recording time period and alarm time period can be customized 5.6.
5.6.8 Email settings 5.6.
5.6.10 Video setting and audio setting 5.6.
Need to change the camera time to the local time zone first 5.6.
5.6.13 SD card setting The files in the SD card cannot be deleted to keep the playback function coherent, the SD card will automatically overwrite the earliest recording 5.6.14 Default setting 6. Computer Browsing Access 6.1 Download Search Tool Download Software from the website ( http://www.gentlen168.com/security-camera/info/898.html) or Mini CD in the package,open the file and install search tool in your computer. Click “next” to find IP camera. Also You can select Network Card to search IP Camera.
nfiguration of the camera such as: IP address, user and password, camera name, etc... You can also access the camera through the browser (recommended IE browser), in the browser you t the camera and configure all the settings of the camera. . 6.2 Search IP Camera Click “next” to find IP camera. You can select Network Card to search IP Camera.
6.3 View Video by Browser Support IE, Google and Firefox browser, Install ActiveX before view video. 6.4 Interface Region A Multiple preview modes. View memory card capacity and date. Region B Click on the capture and take the current image.
Local manual recording. Video Recording playback: Click the playback, select the date and time, select the local playback or SD card playback, search the video files and double click on the file to play. PTZ control operation interface, control the camera to rotate horizontally and vertically. Control the camera zoom in/out, focus +/-, left / right and up / down cruise.
Image: Adjust the brightness, saturation, contrast, exposure parameter and set the WDR, Aemode, Imgmode, Intelligent night mode, IR LED Control, IRCut in this interface. (The camera does not support full colour night vision and smart night vision currently.) Audio: Audio type support G711 / 726 protocol, audio stream selection on/off, audio input type selection, input / output volume adjustment 6.5.2 SettingNetwork Network: The IP address can be selected manually settings or automatically obtain.
Wireless: Enable Wireless to search and select the wireless network that you want to add, input password. Click the “check” to verify camera if connected to the wireless signal. DDNS: To set up DDNS (Remote access), requesting an dynamic domain name to fill in the username and password which provided by Service provider. Contact us to get the cam ID number, each camera username and password will be different. Also you could use a third-party domain name to set it up.
Platform: this function was replaced by P2P, please use P2P to complete your setting. ONVIF: Set the Server Port, Preview, Time zone Setting, Image Setting, NVC Type in this interface. P2P: Enable this function, can watch video in Mobile App via add UID Number.
6.5.3 SettingAlarm Audio alarm: Enable this function. Need to connect a buzzer, turn on & adjust the volume, audio alarm can work well. Motion detection: There are 4 windows selections under Motion Detection.
different window positions. Drag the selected window to enlarge the window proportion. Manually type the sensitivity value or swipe the sensitivity bar to adjust the sensitivity. Alarm: Email setting method is the same as Phone APP. Set the FTP server setting and Image capture in this interface. Schedule: Select the time and click on the “Apply”.
6.5.4 Setting Advanced User: For Change password.
Auto snap: Time capture, Choose to set the SD card snap interval or FTP snap interval and save route. Timed record: Set the Record files duration, whether to open Record and stream.
Email Setting: FTP Setting:
Terminal: Set the cruise laps, select the centred while self-check on/off, close the alarm PTZ movement on/off and indicator display mode. 485Set: These cameras can’t support RS485. Multiple setting: In the same LAN, two or more of this series products from our company's, can be displayed on the same page via this Multiple Setting.
Video Shade: Video shade setting method is the same as the motion detection. Restart timer: Turn on the restart timer and set restart time, then click “Apply”, the camera will follow the settings to scheduled reboot.
6.5.5 Settings System Time: Select the NTP server to synchronize the camera with the internet network time, click to “Sync with PC time”. The camera time automatically becomes the time displayed on the computer. Initialize: Set the Language (only available in Chinese and English currently), Lenstype, Reboot, Factory default, Backup setting data and system upgrade in this interface.
Device information: The device information include device ID, device type, network connection and etc. System Log: The system log records all the steps of the device.
7. Video Management Software (HIP2P Client) Using Video Management software to view multiple cameras at the same time 7.1 Software installation Scarica dal sito Web (http://www.gentlen168.com/security-camera/info/898.html) o Mini CD nel pacchetto. Installalo sul tuo computer. Nota: questo programma riconosce l'UID della videocamera e non l'IP della videocamera.
7.2 Add Camera A） Open the software, click , to login system, default password: leave it blank.
B） Click to Set an Area name (Like: office / home / factory……), you also can modify and delete Area as picture showing below. C） Click “Search” to find IP Camera in the LAN, Select the camera click “add” to Add camera.
D） Double Click camera’s UID to modify camera’s password. (Applicable after the camera is added to wifi, or after the camera has been connected to the network by cat5/6. You can access your camera anywhere by internet.). E） Click Back to preview screen, Double-click the camera name in the device list to preview the screen in real time.
. Frequently Asked Questions Q1: Remote viewing, appear pause and delay phenomenon? A:1) Related to network data, it is recommended to adjust the HD mode to Smooth mode when watching, and the video file is still saved in HD mode. 2) Try to reduce the camera stream when view the video, reducing the stream may affect the quality of the image. 3) Remote viewing, the network recommends uploading network data up to 512KB/S. Download data 256KB/S to watch the best.
A:1) Login to web version and go to the camera setting, change the automatic IP address to manual setting. 2) The IP address which automatically obtain will vary depending on the IP assigned by your router's DHCP. Q5: Is the device not online? A:1) The router disables MAC address filtering. 2) If it is a dual-band router, it needs to use 2.4GWi-Fi and not support 5GWi-Fi. 3) The preferred server address (DNS) of the router is changed to the telecommunications service provider DNS.
Q15: Can't search for the camera IP address in the local area network. A: Our device default IP address network segment 192.168.1.X, you need to modify your network IP address network segment to the same network segment, then use the search tool on the CD to search for IP addresses.
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
