UNDERWATER SCOOTER USER MANAUL STERMAY M1 Please read the operation instructions carefully before using this product. Please operate in the correct way based on complete understanding.
STERMAY Honor customers Thank you for you choice STERMAY M1! STERMAY M1 is one type technology products which able to provide thrust power for you under water. It has small body, portable and disassemble structure, easy to carry, use and renewal. Machine body bottom set integrated type outer configured sliding rail, coordinate the switch part according to your requirements, able to carry different outer configure equipment (SUP, sport camera, lighting lamp, etc).
STERMAY Caution! !This device complies with Part 15 of the FCC Rules / Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation.
STERMAY 02 Content 1. Product overview 1.1 Product overview............................03 2. Safety warnings 2.1 Safety warnings...............................03 3. Product Introduction 3.1 Package list .....................................06 3.2 Specification ...................................06 3.3 Product diagram.............................07 4. Assembling Instruction 4.1 Install the Battery...........................08 4.2 Remove the Battery........................08 4.3 Handle assembling...
STERMAY 1. Product overview STERMAY M1 formed with head cover, body, remote handle, handle, propeller and tail cover, the power system integrated into machine body, remote handle set signal remote system. Face of machine set OLED display screen that indicate the signal connection, rest power volume, speed mode and other information.
STERMAY 04 !This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. !Children shall not play with the appliance. !Cleaning and user maintenance shall not be made by children without supervision.
STERMAY 05 !Before using this product,please take protective measure,be sure to wear the life jacket or life saving equipment, and accompanied by the diver with experience. !When useing this product,please wear life jacket or life-saving equipment, wear well swim cap, never dress the loosen cloth, keep safety distance with the people who are long hair or dress loosen cloth, avoid the long hair or loosen cloth rolling into propeller.
06 STERMAY 3. Product Introduction 3.1 Package list ·Main Unit*1 ·Remote Handle*1 ·Handle*1 ·Bettery*1 ·Switching power supply*1 ·O Ring*2 ·Camera Bracket*1 ·Connect Bracket ·Connect Bracket ·Type-C*1 ·Typy-C adapter*1 ·Remote handle anti ·Remote handle anti ·User Manual*1 A*1 B*1 lose rope (long type)*1 lose rope(short type)*1 3.2 Specification Size The while machine Weight Power Speed Speed Setting Working Depth Durable time Add-on Support 41 x 33.5 x 17.
STERMAY 07 3.
08 STERMAY 4. Assembling Instruction Fast Disassemble Button 4.1 Install the Battery 1.Press the Fast Disassemble Button to remove the Head Cover. Tighten Nut 2.Push the Battery into cabin according the shape of Battery Compartment until the bottom. 3.Force to tightly insert after make the Fix Position Groove of power supply joint outer wall on Main Unit corresponding to the Convex Rib on internal wall of battery power supply joint. 4.Turn Tighten Nut clockwise until tightened. 5.
STERMAY 09 4.3 Handle assembling 1. Main Unit is placed with the Display Screen as the front。 2. Take out the Handle ,Remote Handle. 3. Kindly pay attention to check the front and back directions of Handle and Remote Handle installations,so that the Remote Handle is in right of Main Unit. 4.
10 STERMAY 5. Charging Instruction 5.1 Battery charging 1.Connect the plug pins of Switching Power Supply to the AC power. 2.Connect another end of Switching Power Supply to Battery 5.2 Remote Handle charging 1.Open the Seal Cover of Type-C of Remote Handle. 2.Please use 5V/1A power adapter or standard USB charger port to charge. slot. 3.Insert one end of the Type-C Charge Cable into the Remote the battery is not fully charged,and Green indicates that the 4.
STERMAY 11 6. Operating instruction 6.1 How to use when diving 1. Press the Power Switch for 2s on Main Unit,the power is on when Disply Screen lights up,then the signal icon waiting signal of Remote Handle to connect. start flashing and 2. Long press the F Key on Remote Handle for 2s ,the connection is successful after the Indicator light on and the signal icon always on.
STERMAY 12 6.2 How to use when suspended on SUP. 1.The operation steps for power-on and signal connection same to 6.1 (How to use when dinving). 2.After the Main Unit and Remote Handle signal are connected,the M1 suspended on SUP start working when press down M Key on Remote Handle. 3.Short press F Key to shift the speed setting; Short press both of M Key or Start-stop button to stop working; Long press F Key to power off your M1.
STERMAY 7.Outer configure equipment installation methods 7.1.1 Install the M1 on SUP (By the Connect Bracket A) 13 Connect Bracket A 1.Make the Connect Bracket A align to the Track of Main Unit,and slide the Connect Bracket A into the Main Unit until the screw holes of both are aligned. Bolt 2.Rotate the Bolt on the Connect Bracket A and fasten it to the Main Unit. 3.Make another end of Connect Bracket A and SUP rail aligned after the Connect Bracket A and Track of Main Unit connection finished. 4.
STERMAY 14 7.1.2 Install the M1 on SUP(By the Connect Bracket B) 1. The installation method of connecting bracket B and Main Unit Connect Bracket B Track is the same as that of connecting bracket A. 2. After the installation, the Main Unit with Connect Bracket B should be keep a tilt angle with the SUP mounting base. 3. Align the Location Pin on the connect bracket B with the Limit notch on the sup mounting base, and slowly push it into and Bolt slide it forward to tighten it. 4.
STERMAY 15 Underwater Sport 7.2 Install the sport camear on the M1 1.Make the Camera Bracket align to the Track of Main Unit,and slide the Camera Bracket into the Main Unit until the screw Bolt 2 Camera (Not Provided) holes of both are aligned. 2.Rotate the Bolt 1 on the Camera Bracket and fasten it to the Main Unit. 3 Track Bolt 1 Camera Bracket 2 1 3.
16 STERMAY 8. Maintenance 8.1 Cleaning after use Please refer the below steps for maintenance after each used to maintain the good performance: 1.Immerse the M1 in a container filled with clean water(not seawater) for 20 minutes. 2.Hold the Handle and Remote Handle ,turn it on with slow speed for 2s~3s and repeat this for 3~5 times while the product is completely immersed into water. 3.Dry the M1 with a soft,clean,dry cloth. 4.Disammble the Remote Handle and Handle. 5.
STERMAY 17 8.4 Warranty Policy !In case of faults during use,please contact and consult with after-service of company to avoid the delay in your use and maintenance period.
R Manufacturer: JIANGSU YOUMAY ELECTRIC APPLIANCE CO., LTD Manufacturer's address: No.